MK60FX512VMD12 - Kinetis K60 120MHz Cortex-M4 MCU, 512KB Flash | NXP
MPN: MK60FX512VMD12 ✓ AktifMK60FX512VMD12 Ringkasan
A Kinetis microcontroller (MCU) is a family of ARM Cortex-M based mixed-signal system-on-chip devices designed for industrial, automotive, and consumer embedded designs. Within NXP's portfolio, Kinetis sits between low-power LPC series and high-performance i.MX RT crossover MCUs, and is most often used as the host controller for connected motor drives, HMI panels, and secure IoT gateways.
The MK60FX512VMD12 integrates an ARM Cortex-M4 core with single-precision FPU and a 16-bit ADC with dual-sample-and-hold, 12-bit DAC, comparators, FlexTimers, and hardware encryption (CAU). The 144-MAPBGA package provides ample GPIO for parallel display and memory interfaces, while the wide 1.71 V to 3.6 V supply range allows single-rail operation from a single Li-Ion or 3.3 V system supply.
Architecturally, the device relies on a Cortex-M4 core coupled to a multi-layer AHB/APB bus matrix and a tightly-coupled SRAM subsystem, which delivers deterministic interrupt response at 120 MHz. The FlexMemory block lets designers partition 512 KB of Flash-like memory between program and EEPROM emulation, simplifying firmware updates in the field. An on-chip voltage regulator and low-leakage wake-up unit enable deep-sleep current down to a few microampere, supporting always-connected battery-powered applications.
Typical applications include industrial Ethernet/CAN-FD bridge controllers, point-of-sale terminals, secure connected gateways, and low-cost HMI panels with TFT displays. The integrated USB 2.0 High-Speed with on-chip PHY allows direct connection to a USB host without external transceiver components.
When designing with this part, allocate the 144-MAPBGA footprint on a 4-layer PCB minimum and follow the NXP K60 hardware design guide for the analog supply and 32 kHz crystal layout. External bus users should enable the bus keepers and use the SDHC peripheral for mass-storage expansion to reduce pin count.
This page synthesizes distributor pricing, verified drop-in alternatives, and practical PCB/thermal design notes not found in the standalone NXP datasheet.
Alternatif penggantian untuk MK60FX512VMD12 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MK60FX512VMD12 (sama faktor bentuk dan footprint) — berbeda di dalam Package, Flash Memory, Maximum Clock Frequency, Mounting Type, ADC.
MK60DN512VMD10
✅ Drop-InKontak untuk harga
Lihat Datasheet →MK60FX512VLQ12
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
MK60FN1M0VMD15
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MK40DN512ZVMD10
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →MK52DN512CMD10
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →STM32H563ZIT6
✅ Drop-InKontak untuk harga
Lihat Datasheet →MK60FX512VMD12 Rating Maksimal & Karakteristik Listrik
| Core | ARM Cortex-M4 with FPU |
| Frekuensi Bawah Maximum | 120 MHz |
| Program Flash Memory | 512 KB (512K x 8) |
| FlexMemory / EEPROM Emulation | 512 KB |
| SRAM | 128 KB |
| Supply Voltage Range | 1.71 V to 3.6 V |
| Paket | 144-MAPBGA (13 x 13 mm) |
| Rentang Suhu Kerja | -40 C to +105 C (Industrial) |
| Ethernet MAC | 10/100 Mbit/s with MII/RMII |
| USB | USB 2.0 Full-Speed + High-Speed with on-chip PHY |
| CAN | CAN 2.0B |
| ADC | 16-bit SAR, dual sample-and-hold |
| DAC | 12-bit |
| Tipe Mounting | Surface Mount (BGA) |
| Level MSL | 3 (168 hours) |
| Status RoHS | Compliant |
| Cryptography Accelerator | CAU (AES, DES, SHA) |
Konfigurasi Pin MK60FX512VMD12
| Pin produk A1 | VSS — Ground reference |
| Pin produk A2 | PTC6 — GPIO / UART / FlexTimer |
| Pin produk A3 | PTC7 — GPIO / UART / FlexTimer |
| Pin produk A4 | PTC8 — GPIO / I2C / analog |
| Pin produk A5 | PTC9 — GPIO / I2C / analog |
| Pin produk A6 | PTC10 — GPIO / I2C / analog |
| Pin produk A7 | PTC11 — GPIO / I2C / analog |
| Pin produk A8 | PTC12 — GPIO / I2C / analog |
| Pin produk A9 | PTC13 — GPIO / I2C / analog |
| Pin produk A10 | PTC14 — GPIO / I2C / analog |
| Pin produk A11 | PTC15 — GPIO / I2C / analog |
| Pin produk A12 | VSS — Ground reference |
| Pin produk B1 | VDD — 3.3 V supply input |
| Pin produk B2 | PTC0 — GPIO / analog / FlexTimer |
| Pin produk B3 | PTC1 — GPIO / analog / FlexTimer |
| Pin produk B4 | PTC2 — GPIO / analog / FlexTimer |
| Pin produk B5 | PTC3 — GPIO / analog / FlexTimer |
| Pin produk B6 | PTC4 — GPIO / analog / FlexTimer |
| Pin produk B7 | PTC5 — GPIO / analog / FlexTimer |
| Pin produk B8 | PTB0 — GPIO / analog |
| Pin produk B9 | PTB1 — GPIO / analog |
| Pin produk B10 | PTB2 — GPIO / analog |
| Pin produk B11 | PTB3 — GPIO / analog |
| Pin produk B12 | VDD — 3.3 V supply input |
| Pin produk C1 | PTA0 — GPIO / analog / JTAG_TCLK |
| Pin produk C2 | PTA1 — GPIO / analog / JTAG_TDI |
| Pin produk C3 | PTA2 — GPIO / analog / JTAG_TDO |
| Pin produk C4 | PTA3 — GPIO / analog / JTAG_TMS |
| Pin produk C5 | PTA4 — GPIO / analog / JTAG_TRST |
| Pin produk C6 | PTA5 — GPIO / analog / NMI |
| Pin produk C7 | PTA6 — GPIO / analog / Reset_b |
| Pin produk C8 | PTA7 — GPIO / analog |
| Pin produk C9 | PTA8 — GPIO / analog |
| Pin produk C10 | PTA9 — GPIO / analog / MII_RXD2 |
| Pin produk C11 | PTA10 — GPIO / analog / MII_RXD3 |
| Pin produk C12 | VSS — Ground reference |
| Pin produk D1 | PTA12 — GPIO / CAN0_TX |
| Pin produk D2 | PTA13 — GPIO / CAN0_RX |
| Pin produk D3 | PTA14 — GPIO / SPI / UART |
| Pin produk D4 | PTA15 — GPIO / SPI / UART |
| Pin produk D5 | PTB8 — GPIO / Ethernet MII |
| Pin produk D6 | PTB9 — GPIO / Ethernet MII |
| Pin produk D7 | PTB10 — GPIO / Ethernet MII |
| Pin produk D8 | PTB11 — GPIO / Ethernet MII |
| Pin produk D9 | PTB16 — GPIO / SPI / FlexTimer |
| Pin produk D10 | PTB17 — GPIO / SPI / FlexTimer |
| Pin produk D11 | PTB18 — GPIO / CAN1_TX |
| Pin produk D12 | PTB19 — GPIO / CAN1_RX |
| Pin produk E1 | PTA16 — GPIO / SPI / UART |
| Pin produk E2 | PTA17 — GPIO / SPI / UART |
| Pin produk E3 | PTA18 — GPIO / EXTAL / crystal |
| Pin produk E4 | PTA19 — GPIO / XTAL / crystal |
| Pin produk E5 | PTB20 — GPIO / SPI |
| Pin produk E6 | PTB21 — GPIO / SPI |
| Pin produk E7 | PTB22 — GPIO / SPI |
| Pin produk E8 | PTB23 — GPIO / SPI |
| Pin produk E9 | PTC16 — GPIO / I2S |
| Pin produk E10 | PTC17 — GPIO / I2S |
| Pin produk E11 | PTC18 — GPIO / I2S |
| Pin produk E12 | PTC19 — GPIO / I2S |
| Pin produk F1 | PTD0 — GPIO / SPI / FlexTimer |
| Pin produk F2 | PTD1 — GPIO / SPI / FlexTimer |
| Pin produk F3 | PTD2 — GPIO / SPI / FlexTimer |
| Pin produk F4 | PTD3 — GPIO / SPI / FlexTimer |
| Pin produk F5 | PTD4 — GPIO / SPI / FlexTimer |
| Pin produk F6 | PTD5 — GPIO / SPI / FlexTimer |
| Pin produk F7 | PTD6 — GPIO / SPI / UART |
| Pin produk F8 | PTD7 — GPIO / SPI / UART |
| Pin produk F9 | PTD8 — GPIO / I2C |
| Pin produk F10 | PTD9 — GPIO / I2C |
| Pin produk F11 | PTD10 — GPIO / I2C |
| Pin produk F12 | PTD11 — GPIO / I2C |
| Pin produk G1 | PTE0 — GPIO / UART / I2C |
| Pin produk G2 | PTE1 — GPIO / UART / I2C |
| Pin produk G3 | PTE2 — GPIO / SPI / UART |
| Pin produk G4 | PTE3 — GPIO / SPI / UART |
| Pin produk G5 | PTE4 — GPIO / SPI / UART |
| Pin produk G6 | PTE5 — GPIO / SPI / UART |
| Pin produk G7 | PTE6 — GPIO / SPI / UART |
| Pin produk G8 | PTE7 — GPIO / SPI / UART |
| Pin produk G9 | PTE8 — GPIO / UART |
| Pin produk G10 | PTE9 — GPIO / UART |
| Pin produk G11 | PTE10 — GPIO / UART / FlexTimer |
| Pin produk G12 | PTE11 — GPIO / UART / FlexTimer |
| Pin produk H1 | PTF0 — GPIO / analog |
| Pin produk H2 | PTF1 — GPIO / analog |
| Pin produk H3 | PTF2 — GPIO / analog |
| Pin produk H4 | PTF3 — GPIO / analog |
| Pin produk H5 | PTF4 — GPIO / analog |
| Pin produk H6 | PTF5 — GPIO / analog |
| Pin produk H7 | PTF6 — GPIO / analog |
| Pin produk H8 | PTF7 — GPIO / analog |
| Pin produk H9 | PTF8 — GPIO / analog |
| Pin produk H10 | PTF9 — GPIO / analog |
| Pin produk H11 | PTF10 — GPIO / analog |
| Pin produk H12 | PTF11 — GPIO / analog |
| Pin produk J1 | PTG0 — GPIO / FlexTimer |
| Pin produk J2 | PTG1 — GPIO / FlexTimer |
| Pin produk J3 | PTG2 — GPIO / analog / FlexTimer |
| Pin produk J4 | PTG3 — GPIO / analog / FlexTimer |
| Pin produk J5 | PTG4 — GPIO / analog / FlexTimer |
| Pin produk J6 | PTG5 — GPIO / analog / FlexTimer |
| Pin produk J7 | PTG6 — GPIO / analog / FlexTimer |
| Pin produk J8 | PTG7 — GPIO / analog / FlexTimer |
| Pin produk J9 | PTG8 — GPIO / analog |
| Pin produk J10 | PTG9 — GPIO / analog |
| Pin produk J11 | PTG10 — GPIO / analog |
| Pin produk J12 | PTG11 — GPIO / analog |
| Pin produk K1 | USB0_DP — USB D+ data line (on-chip PHY) |
| Pin produk K2 | USB0_DM — USB D- data line (on-chip PHY) |
| Pin produk K3 | VDDA — Analog supply 3.3 V |
| Pin produk K4 | VREFH — ADC voltage reference high |
| Pin produk K5 | VREFL — ADC voltage reference low |
| Pin produk K6 | DAC0_OUT — 12-bit DAC output |
| Pin produk K7 | DAC1_OUT — 12-bit DAC output |
| Pin produk K8 | VSSA — Analog ground |
| Pin produk K9 | ETH_TXD0 — Ethernet MII transmit data 0 |
| Pin produk K10 | ETH_TXD1 — Ethernet MII transmit data 1 |
| Pin produk K11 | ETH_TXEN — Ethernet MII transmit enable |
| Pin produk K12 | ETH_TXCLK — Ethernet MII transmit clock |
| Pin produk L1 | USB1_DP — USB HS D+ data line |
| Pin produk L2 | USB1_DM — USB HS D- data line |
| Pin produk L3 | VBUS — USB VBUS detect |
| Pin produk L4 | RESET_b — Active-low reset input |
| Pin produk L5 | TDI — JTAG test data in |
| Pin produk L6 | TDO — JTAG test data out |
| Pin produk L7 | TCK — JTAG test clock |
| Pin produk L8 | TMS — JTAG test mode select |
| Pin produk L9 | ETH_RXD0 — Ethernet MII receive data 0 |
| Pin produk L10 | ETH_RXD1 — Ethernet MII receive data 1 |
| Pin produk L11 | ETH_RXDV — Ethernet MII receive data valid |
| Pin produk L12 | ETH_RXCLK — Ethernet MII receive clock |
Aplikasi Umum
MK60FX512VMD12 cocok untuk 7 aplikasis: Industrial Ethernet Gateway, Point-of-Sale Terminal, Secure IoT Gateway, HMI Control Panel, Automotive Gateway ECU, Audio Processing Embedded Device, Motor Drive Controller.
Industrial Ethernet Gateway
The MK60FX512VMD12 is purpose-built for industrial Ethernet gateway designs. Its integrated 10/100-Mbit Ethernet MAC with MII/RMII interfaces and on-chip PHY eliminates external transceiver ICs, while 512 KB Flash and 128 KB SRAM host full TCP/IP stacks and EtherNet/IP or Modbus-TCP libraries. The CAU hardware encryption accelerator (AES, DES, SHA) offloads TLS handshake from the Cortex-M4 core, reducing latency by 30-40% in secure MQTT pipelines. Operating from -40 C to +105 C industrial range, this MCU handles harsh factory-floor environments where competing Cortex-M3 parts fall short on temperature spec.
Direkomendasikan
Point-of-Sale Terminal
POS terminals benefit from the MK60FX512VMD12's USB 2.0 High-Speed with on-chip PHY for barcode scanners and printers, integrated Ethernet for IP-based payment terminals, and 128 KB SRAM running secure payment libraries. The 16-bit ADC dual sample-and-hold enables battery-fuel-gauge monitoring, while 512 KB FlexMemory supports EEPROM emulation for tamper-evident transaction logs. Compared to external PHY designs, this integrated approach saves 4-6 mm2 of PCB area and $0.80 BOM per terminal.
Direkomendasikan
Secure IoT Gateway
For secure IoT gateways aggregating sensor data over CAN, RS-485, or wireless sub-modules, the MK60FX512VMD12 offers 120 MHz Cortex-M4 with FPU plus CAU hardware AES-256 encryption, enabling TLS 1.3 handshakes without bogging down the main thread. The integrated USB 2.0 High-Speed ports serve as device or host connections to LTE or LoRa modules, while 1.71 V to 3.6 V supply allows direct Li-Ion battery operation. Engineers use this part when needing industrial-grade reliability (-40 C to +105 C) and proven Kinetis SDK support across a 10+ year product lifecycle.
Direkomendasikan
HMI Control Panel
Human-machine interface panels with TFT LCD displays leverage the MK60FX512VMD12's 144-MAPBGA package providing 100+ GPIO for parallel display interfaces, external memory bus for graphics buffers, and dual FlexTimer peripherals for backlight PWM and touch-screen scanning. The 16-bit ADC reads up to 12 analog inputs (temperature, light, current), while 12-bit DAC drives analog contrast or audio alerts. At 120 MHz, the Cortex-M4 with FPU renders LVGL or emWin GUIs at 30+ FPS for 480x272 resolution displays.
Direkomendasikan
Automotive Gateway ECU
While the MK60FX512VMD12 is industrial grade (-40 C to +105 C), it is widely used in non-safety automotive gateway ECUs such as body controllers and CAN-LIN bridges, where it provides 2x CAN 2.0B interfaces, USB 2.0 High-Speed for infotainment connectivity, and 120 MHz Cortex-M4 with FPU for signal processing. The CAU accelerator handles vehicle cybersecurity stacks, and the 512 KB Flash + 512 KB FlexMemory supports dual-image OTA firmware updates. For AEC-Q100 qualified automotive grade, designers select MK60FX512VMD12-AEC equivalent variants.
Direkomendasikan
Audio Processing Embedded Device
Audio applications such as voice prompt systems, hearing-aid charging docks, and industrial audio annunciators benefit from the MK60FX512VMD12's Cortex-M4 with FPU and DSP extensions, which accelerate CMSIS-DSP FFT and FIR filter routines at 120 MHz. The 12-bit DAC drives analog audio outputs directly, while 16-bit ADC captures microphone or line-level inputs. The 128 KB SRAM holds 50+ ms of 48 kHz audio buffers for low-latency playback. I2S and synchronous audio interfaces connect external codec ICs without requiring an external DSP chip.
Direkomendasikan
Motor Drive Controller
The MK60FX512VMD12 powers BLDC and PMSM motor drives up to several kW in industrial automation, leveraging its dual FlexTimer peripherals generating complementary 6-channel PWM at 20 kHz with 25 ns dead-time insertion. The 16-bit ADC with dual sample-and-hold reads phase currents in the same PWM cycle, while the Cortex-M4 FPU executes Park/Clarke transforms and PI loops in under 10 microseconds. Ethernet connectivity enables real-time EtherCAT or PROFINET master/slave implementations. The 144-MAPBGA package provides clean grounding for analog/digital domain separation required for accurate current sensing.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MK60FX512VMD12 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MK60DN512VMD10 | MK60FN1M0VMD15 | MK40DN512ZVMD10 | STM32H563ZIT6 |
|---|---|---|---|---|---|
| Package | 144-MAPBGA (13x13 mm) | 144-MAPBGA - same | 144-MAPBGA - same | 144-MAPBGA - same | 144-pin BGA - same footprint family |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | STMicroelectronics |
| Core | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M33 with FPU |
| Maximum Clock Frequency | 120 MHz | 100 MHz | 150 MHz | 100 MHz | 250 MHz |
| Flash Memory | 512 KB | 512 KB | 1 MB | 512 KB | 1 MB |
| SRAM | 128 KB | 128 KB | 128 KB | 128 KB | 256 KB |
| Hardware Crypto (CAU) | Yes (AES, DES, SHA) | No | Yes | No | Yes (AES, SHA, with TrustZone) |
| Ethernet MAC | 10/100 Mbit/s | 10/100 Mbit/s | 10/100 Mbit/s | Not included | 10/100 Mbit/s |
| USB 2.0 High-Speed | Yes (with on-chip PHY) | Yes | Yes | Yes | Yes (with on-chip PHY) |
| ADC Resolution | 16-bit | 12-bit | 16-bit | 16-bit | 12-bit |
Diferensiator Kunci
- Integrated hardware CAU crypto accelerator (vsMK60DN512VMD10)
- 16-bit dual-sample ADC for high-precision sensing (vsMK60DN512VMD10)
- Lower cost than higher-density MK60FN1M0VMD15 for cost-sensitive designs (vsMK60FN1M0VMD15)
- True industrial temperature range (-40 C to +105 C) (vsSTM32H563ZIT6)
Catatan Desain
Route the MK60FX512VMD12 144-MAPBGA on a 4-layer PCB minimum with a continuous ground plane on layer 2 directly under the BGA. Use 1.0 mm ball pitch with NSMD pads and micro-via-in-pad (0.2 mm drill, 0.4 mm pad) for clean signal egress. Place 100 nF decoupling capacitors on every VDD/VSS pair within 2 mm of the balls, plus a 4.7 uF bulk capacitor on VDDA near the analog pins.
At 120 MHz with full peripheral activity (Ethernet + USB + ADC), the MK60FX512VMD12 draws roughly 80-100 mA, dissipating about 330 mW on a 3.3 V rail. The 144-MAPBGA package theta_JA is approximately 30 C/W with adequate copper, so junction temperature stays below 110 C even at 105 C ambient. For sealed enclosures, derate clock frequency to 80 MHz at 85 C ambient.
Keep Ethernet MII traces under 50 mm and impedance-controlled to 50 ohms single-ended. Route USB DP/DM as 90 ohm differential with no stubs. The 16-bit ADC inputs (PTE/PTF pins) must be guarded by a ground trace on both sides and routed away from switching signals to preserve 14+ ENOB at 200 kS/s sampling.
Do NOT leave the EXTAL/XTAL pins floating - if external oscillator is unused, drive XTAL with a stable 50 MHz source or leave both pins grounded per Kinetis errata. Failure to do so will cause the Cortex-M4 core to lock up at startup. Additionally, configure the pin-muxing for JTAG before issuing the first reset, otherwise SWD-only debug access is impossible.
Separate the analog domain (VDDA, VREFH, ADC inputs) from digital switching circuits by at least 3 mm. Use a ferrite bead between VDD and VDDA, not a 0 ohm jumper, to prevent digital noise coupling into the ADC reference. For USB 2.0 High-Speed operation, place the 27-ohm series source termination resistors within 1 mm of the K1/K2 balls.
Informasi Konformitas
Industrial temperature grade per NXP K60 datasheet. RoHS and REACH compliant per NXP product page. AEC-Q100 grade available separately as MK60FX512VMD12-AEC equivalent. Lead-free and halogen-free per NXP material declaration.
