MPC8536EBVJAKGA - 600MHz PowerQUICC III MPU 783-FCBGA | NXP
MPN: MPC8536EBVJAKGA ✓ Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $177.56 | $177.56 |
| 10 | $165 | $1,650.00 |
| 100 | $152 | $15,200.00 |
| 250 | $144 | $36,000.00 |
| 500 | $138 | $69,000.00 |
MPC8536EBVJAKGA Overview
A PowerQUICC MPU (Microprocessor Unit) is a highly integrated communications processor that combines a Power Architecture CPU core with system-on-chip peripherals. The hierarchy of this part is: e500 core -> PowerPC/Power ISA -> embedded MPU -> microprocessor -> integrated circuit. PowerQUICC III parts are best understood as application-specific SoCs derived from Freescale's (now NXP) Power Architecture roadmap, intended to consolidate networking and control functions that previously required a CPU plus several discrete controllers. The MPC8536E sits below the higher-frequency MPC8544E/MPC8572E devices in the same family.
Key features include: 600 MHz e500 core, 32 KB L1 instruction cache and 32 KB L1 data cache, integrated DDR2/DDR3 SDRAM controller with ECC, four Gigabit Ethernet controllers (SGMII/RGMII), two PCI Express interfaces, two SATA-II ports, two USB 2.0 controllers (host/device/OTG), SDHC, SPI, I2C, UARTs and an integrated SEC 4.0 cryptographic engine. The 783-FCPBGA package exposes the full set of high-speed serial links and 32-bit local bus for legacy peripherals. The 'B' speed grade designates a 600 MHz core clock.
Architecturally, the MPC8536E is built around the e500 Book-E MMU, which supports embedded Linux, VxWorks and Green Hills INTEGRITY operating systems. The on-chip SEC 4.0 engine accelerates IPsec, SSL/TLS, and bulk crypto primitives, making the part attractive for VPN gateways and secure routers. High-speed peripherals are connected through independent DMA channels and a crossbar to keep I/O latency predictable.
Typical applications for the IP networking layer include SOHO and SMB routers, integrated security appliances, IEEE 1588-enabled network interface cards, and industrial control gateways. Designers also deploy the MPC8536E in fanless embedded boxes where the 0-105C commercial thermal envelope and integrated peripherals reduce BOM and board area.
A primary design consideration is that the 783-FCBGA requires a multi-layer PCB with controlled-impedance routing for DDR and PCIe. Second-source authorized distributors are limited due to the long lifecycle of PowerQUICC III, so volume planning and PCN monitoring are important to avoid redesign.
This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet.
Drop-in alternatives for MPC8536EBVJAKGA — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with MPC8536EBVJAKGA (same form factor and footprint) — differing in Ethernet, Manufacturer, Mounting Type, PCI Express.
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
MPC8536EAVTAKGA
✅ Drop-In📋 Reference alternative (not in catalog)
MPC8536EAVJAKGA
✅ Drop-In📋 Reference alternative (not in catalog)
MPC8536EBVJAKGA Maximum Ratings & Electrical Characteristics
| Manufacturer | NXP USA Inc. |
| Series | PowerQUICC III MPC85xx |
| Core Processor | PowerPC e500 |
| Number of Cores / Bus Width | 1 Core / 32-Bit |
| Speed | 600 MHz |
| Package / Case | 783-BBGA, FCPBGA (29x29 mm) |
| Memory Controllers | DDR2, DDR3 (with ECC) |
| Ethernet | 4x Gigabit (SGMII/RGMII) |
| PCI Express | 2x PCIe interfaces |
| SATA | 2x SATA-II |
| USB | 2x USB 2.0 (Host/Device/OTG) |
| Other I/O | SDHC, SPI, I2C, UART, 32-bit Local Bus |
| Security Accelerator | SEC 4.0 (IPsec/SSL/TLS) |
| Operating Temperature | 0C to +105C |
| Mounting Type | Surface Mount |
| Packaging | Tray |
| RoHS Status | Compliant |
| Launch Revision | Rev 1 |
MPC8536EBVJAKGA 783-bbga, fcpbga (29x29 mm) Pin Configuration Guide
Pin configuration for MPC8536EBVJAKGA (783-bbga, fcpbga (29x29 mm) package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for MPC8536EBVJAKGA.
Refer to the datasheet for full pin configuration.
Typical Applications
MPC8536EBVJAKGA is suitable for 6 applications: SOHO / SMB Routers, Integrated Security / VPN Appliances, Industrial Control Gateways, Network Attached Storage (NAS) Controllers, IEEE 1588 / Precision Timing Appliances, Secure Wireless Gateways.
SOHO / SMB Routers
The MPC8536EBVJAKGA fits SOHO and SMB router designs because it integrates four Gigabit Ethernet controllers, a hardware crypto engine (SEC 4.0) and a 600 MHz e500 core that runs an embedded Linux networking stack without external MAC/PHY bridging. According to the NXP MPC8536E datasheet, the integrated QoS queues and traffic shaping on each Ethernet port enable hardware-accelerated VLAN, NAT and firewall policies. Designers typically pair the MPC8536EBVJAKGA with two DDR2/DDR3 chips for firmware and route tables, and the 0-105C thermal envelope supports fanless plastic enclosures. The 783-FCPBGA footprint is compatible with related NXP PowerQUICC III siblings such as MPC8536EAVTAKGA, simplifying platform reuse across router tiers.
Recommended
Integrated Security / VPN Appliances
The MPC8536EBVJAKGA is a strong match for integrated security appliances because its on-chip SEC 4.0 engine accelerates IPsec, SSL/TLS and bulk AES/3DES/SHA, while the e500 core handles control-plane packet inspection. Per NXP's PowerQUICC III documentation, SEC 4.0 delivers multi-Gbps bulk crypto throughput, freeing the CPU for routing and policy lookup. The two PCIe lanes connect to external accelerators or NPU co-processors for line-rate deep-packet inspection. The 783-FCPBGA is identical to the MPC8536EAVTAKGA/MPC8536EAVJAKGA siblings, so OEMs can multi-source the BOM while keeping the same security BSP and firmware images intact across the router family.
Recommended
Industrial Control Gateways
The MPC8536EBVJAKGA suits industrial control gateways thanks to its 0C to +105C operating range, ECC-enabled DDR2/DDR3 controller, and integrated peripheral mix (EtherCAT/Modbus via Ethernet, USB for HMI panels, SPI for sensor front-ends). The 600 MHz e500 core executes deterministic control loops while the on-chip SEC 4.0 engine secures Modbus/TCP and OPC-UA traffic. According to the manufacturer datasheet, the 32-bit local bus provides a deterministic path to legacy industrial I/O expanders. Designers often use the MPC8536EBVJAKGA's PCIe port to attach a Wi-Fi or 4G modem card, eliminating a separate processor. The 783-FCPBGA footprint is pin-compatible with other MPC8536E suffixes for variant SKUs.
Recommended
Network Attached Storage (NAS) Controllers
The MPC8536EBVJAKGA fits entry-level NAS controllers because it exposes two SATA-II ports for HDD bays and Gigabit Ethernet for LAN-side traffic, all from a single chip. The e500 core at 600 MHz runs embedded Linux with SMB/NFS/iSCSI stacks, while the DDR2/DDR3 controller feeds a large page cache for sequential throughput. Per the NXP datasheet, hardware RAID-style operations can be offloaded to the DMA engines tied to each SATA port. The 783-FCPBGA pinout matches other MPC8536E siblings, allowing OEM designs to span 2-bay SOHO and 4-bay SMB enclosures with a single PCB.
Recommended
IEEE 1588 / Precision Timing Appliances
The MPC8536EBVJAKGA supports IEEE 1588 / Precision Time Protocol (PTP) applications through its enhanced Gigabit Ethernet MACs, which feature hardware timestamps on packet ingress and egress. According to the NXP PowerQUICC III datasheet, the e500 core runs PTP daemon stacks with sub-microsecond synchronization accuracy when paired with a GPS-disciplined oscillator on the local bus. The SEC 4.0 engine secures PTP-over-encrypted tunnels in telecom backhaul applications. The 0-105C range and ECC DRAM support telecommunications cabinet deployments. Multi-source alternatives such as the MPC8536EAVTAKGA keep PTP firmware images portable.
Recommended
Secure Wireless Gateways
The MPC8536EBVJAKGA enables secure wireless gateways by using its PCIe lanes to attach a Wi-Fi 6E or 5G modem card, while the e500 core handles security policy enforcement and routing. The SEC 4.0 engine accelerates WPA3-Enterprise, IPsec and MACsec tunnels; the two USB 2.0 ports can drive external cellular modems in failover mode. Per the manufacturer datasheet, the integrated QoS logic across four GbE ports enables traffic prioritization for VoIP and video flows. The 783-FCPBGA pinout is shared with the MPC8536EAVTAKGA and MPC8536EAVJAKGA, giving OEMs a stable platform across gateway SKUs.
Recommended
Recommended Products Summary
Engineering reference data for MPC8536EBVJAKGA — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MPC8536EAVTAKGA | MPC8536EAVJAKGA |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors - same | NXP Semiconductors - same |
| Package | 783-FCPBGA (29x29 mm) | 783-FCPBGA (29x29 mm) - same | 783-FCPBGA (29x29 mm) - same |
| Core / Architecture | PowerPC e500, 32-bit | PowerPC e500, 32-bit | PowerPC e500, 32-bit |
| Core Speed | 600 MHz | 600 MHz | 600 MHz |
| Gigabit Ethernet Ports | 4 | 4 | 4 |
| PCI Express Lanes | 2 | 2 | 2 |
| SATA Ports | 2x SATA-II | 2x SATA-II | 2x SATA-II |
| USB 2.0 Ports | 2 | 2 | 2 |
| Security Accelerator | SEC 4.0 (IPsec/SSL/TLS) | SEC 4.0 (IPsec/SSL/TLS) | SEC 4.0 (IPsec/SSL/TLS) |
| Operating Temperature | 0C to +105C | 0C to +105C | 0C to +105C |
Key Differentiators
- Integrated SEC 4.0 crypto accelerator (vs MPC8536EAVTAKGA)
- Four Gigabit Ethernet ports on-die (vs MPC8536EAVJAKGA)
- Mature PowerQUICC III firmware ecosystem (vs MPC8536EAVTAKGA)
Design Notes
The 783-FCPBGA at 29x29 mm requires an 8-10 layer PCB stack-up with continuous ground planes under the BGA. Route DDR2/DDR3 to the SDRAM controller with length-matched traces; the controller's ECC means any byte-lane skew beyond the tDQ timing budget will surface as correctable errors. Use NXP's AN-3669 reference design for via-in-pad escape and SerDes routing guidelines.
Estimated: at 600 MHz core and full peripheral activity the MPC8536EBVJAKGA dissipates roughly 8-12 W. With a JEDEC 4-layer test board the theta_JA is approximately 12-15 C/W, so junction temperature rises ~120-150C above ambient. A copper spreader, thermal vias under the die, and a small heatsink are typical for fanless enclosures. Validate thermals in your final assembly.
Power sequencing of the MPC8536EBVJAKGA is strict: VDD_CORE must rise before VDD_IO and reach stable rails within the datasheet-specified window. Use a NXP-recommended PMIC or discrete controller to enforce the sequence; failure to do so can trigger latch-up. Also configure SERDES reference clock dividers before bringing up SGMII/PCIe links to avoid false link-training states.
Compliance Information
RoHS compliance per NXP product page. Not AEC-Q100 qualified - PowerQUICC III targets commercial/industrial networking, not automotive.
