PIC16F1713-E/MV - 8-Bit XLP MCU 7KB Flash 28-UQFN | Microchip
MPN: PIC16F1713-E/MV ✓ Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $2.15 | $2.15 |
| 10 | $1.94 | $19.40 |
| 100 | $1.72 | $172.00 |
| 500 | $1.55 | $775.00 |
| 1,000 | $1.38 | $1,380.00 |
PIC16F1713-E/MV Overview
A microcontroller (MCU) is a single-chip computer containing a processor core, program and data memory, and integrated peripherals. The PIC16F1713 belongs to Microchip's PIC16 enhanced mid-range family, optimized for general-purpose and intelligent analog applications. The 'XLP' (eXtreme Low Power) designation indicates power-saving modes that extend battery life, making this MCU well suited to portable and energy-harvesting designs. As an 8-bit RISC MCU, the PIC16F1713 executes single-cycle instructions, balancing code density with deterministic timing.
Key features include 14-bit instruction word, 32MHz internal oscillator, two operational amplifiers, four 10-bit ADC channels with computation, and core-independent peripherals that offload tasks from the CPU. The Zero Cross Detect (ZCD) and Numerically Controlled Oscillator (NCO) modules support advanced signal conditioning in motor control and lighting applications without software intervention.
The architecture combines intelligent analog integration with low-power operation. On-chip op-amps can drive ADC inputs, implement active filters, or buffer sensor signals. The Configurable Logic Cell (CLC) and Complementary Output Generator (COG) enable custom hardware logic functions, reducing BOM cost by replacing discrete components. Peripheral Pin Select (PPS) allows flexible remapping of digital peripherals to any I/O pin, simplifying PCB layout.
Typical applications include LED lighting control, sensor signal conditioning, battery-powered IoT nodes, motor control, and consumer appliances. The AEC-Q100 qualified grade supports automotive applications such as body electronics and interior lighting. The compact 4x4 mm UQFN package suits space-constrained designs.
Design consideration: When using the internal 32MHz oscillator at full speed, ensure core-independent peripherals are configured to minimize wake events. For battery-powered designs, leverage the nanoWatt XLP sleep modes to reduce current consumption below 1 uA.
This page synthesizes distributor pricing, drop-in package equivalents, and practical design considerations not collected in any single manufacturer document.
Drop-in alternatives for PIC16F1713-E/MV — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with PIC16F1713-E/MV (same form factor and footprint) — differing in Comparators, Package, ADC, DAC, I/O Pins.
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
PIC16F1713-I/MV
✅ Drop-In📋 Reference alternative (not in catalog)
PIC16F1713T-I/MV
✅ Drop-In✓ In Stock
$1.18 / Unit
View Datasheet →PIC16F1716-I/MV
✅ Drop-In✓ In Stock
$1.04 / Unit
View Datasheet →PIC16F15356-I/MV
✅ Drop-In✓ In Stock
$1.18 / Unit
View Datasheet →PIC16F1713-E/MV Maximum Ratings & Electrical Characteristics
| Core Processor | PIC |
| Core Size | 8-bit |
| Program Memory Size | 7 KB (4K x 14) FLASH |
| RAM Size | 512 B |
| EEPROM Size | 0 B (no data EEPROM) |
| Maximum Clock Frequency | 32 MHz |
| Operating Voltage Range | 2.5 V / 3.3 V / 5 V |
| Operating Temperature Range | -40 C to +125 C (Extended, "E") |
| ADC | 10-bit, with Computation |
| DAC | 5/8-bit |
| Comparators | High-Speed |
| On-Chip Op-Amps | Yes (2x) |
| Core-Independent Peripherals | CLC, COG, NCO, ZCD |
| PWM / CCP | Yes (CCP/PWM) |
| Communication | EUSART, I2C, SPI |
| Peripheral Pin Select (PPS) | Yes |
| I/O Pins | Up to 25 |
| Package | 28-pin UQFN (4x4 mm) with EP, MV |
| AEC-Q100 | Qualified (Automotive grade) |
| Mounting Type | Surface Mount |
| MSL Level | MSL3 (per JEDEC J-STD-020) |
| RoHS Status | Compliant |
PIC16F1713-E/MV Pin Configuration
| Pin 1 | VDD — Positive supply voltage |
| Pin 2 | RA5 — Digital I/O / analog input |
| Pin 3 | RA4 — Digital I/O / analog input |
| Pin 4 | RA3 — Digital I/O / analog input |
| Pin 5 | RA2 — Digital I/O / analog input |
| Pin 6 | RA1 — Digital I/O / analog input |
| Pin 7 | RA0 — Digital I/O / analog input |
| Pin 8 | VSS — Ground reference |
| Pin 9 | RA7 — Digital I/O / OSCI |
| Pin 10 | RA6 — Digital I/O / OSCO |
| Pin 11 | RC5 — Digital I/O |
| Pin 12 | RC4 — Digital I/O |
| Pin 13 | RC3 — Digital I/O / SCL |
| Pin 14 | RC2 — Digital I/O |
| Pin 15 | RC1 — Digital I/O / CCP2 |
| Pin 16 | RC0 — Digital I/O |
| Pin 17 | OSC2 — Crystal output |
| Pin 18 | OSC1 — Crystal input |
| Pin 19 | VSS — Ground (optional second pad) |
| Pin 20 | VDD — Positive supply (optional second pad) |
| Pin 21 | RB7 — Digital I/O |
| Pin 22 | RB6 — Digital I/O |
| Pin 23 | RB5 — Digital I/O / AN13 |
| Pin 24 | RB4 — Digital I/O / AN11 |
| Pin 25 | RB3 — Digital I/O / AN9 |
| Pin 26 | RB2 — Digital I/O / AN8 |
| Pin 27 | RB1 — Digital I/O / AN10 |
| Pin 28 | RB0 — Digital I/O / INT |
| Pin EP | EP — Exposed thermal pad - connect to VSS |
Typical Applications
PIC16F1713-E/MV is suitable for 7 applications: Automotive Interior Lighting Control, Battery-Powered IoT Sensor Node, Industrial Sensor Signal Conditioning, Small Motor Control (BLDC / Stepper), Consumer Appliance Control Board, Smart Meter / Energy Monitor, Touch-Sense User Interface.
Automotive Interior Lighting Control
The PIC16F1713-E/MV is well suited to automotive interior LED lighting due to its AEC-Q100 Grade 1 qualification, on-chip operational amplifiers, and Complementary Output Generator (COG) peripheral. The COG module generates complementary PWM with programmable dead-band, directly driving half-bridge MOSFET stages for LED string control. The on-chip op-amps can implement constant-current feedback loops without external amplifier ICs. The 32MHz core and 7KB Flash handle smooth dimming curves via DALI or LIN protocols while the ZCD peripheral synchronizes dimming to AC line transitions in 120V/230V architectural LED drivers.
Recommended
Battery-Powered IoT Sensor Node
The PIC16F1713-E/MV's XLP (eXtreme Low Power) technology makes it a strong choice for battery-powered IoT sensor nodes operating for years on a single coin cell. Sleep current below 1 uA in nanoWatt mode combined with the 10-bit ADC and computation engine handles temperature, humidity, and voltage monitoring with autonomous background measurements. The CLC peripheral wakes the MCU on sensor threshold crossings without software intervention, dramatically reducing average power. The 512B RAM is sufficient for BLE command buffers, while 7KB Flash accommodates custom protocol stacks. The 4x4 mm UQFN keeps the BOM compact for wearable form factors.
Recommended
Industrial Sensor Signal Conditioning
The PIC16F1713-E/MV integrates two operational amplifiers directly on-die, enabling active filter and signal conditioning topologies without external op-amp ICs. The on-chip op-amps can be configured as instrumentation front-ends for bridge sensors, thermocouple amplifiers, or transimpedance stages for photodiodes. Combined with the 10-bit ADC with computation (averaging, oversampling, threshold comparison) and 5/8-bit DAC, the device implements complete analog signal chains. The 32MHz core runs compensation algorithms at 8 MIPS, while the ZCD peripheral synchronizes sampling to AC line cycles for power-quality metering applications.
Recommended
Small Motor Control (BLDC / Stepper)
The PIC16F1713-E/MV drives small brushless DC and stepper motors through its Complementary Output Generator (COG) and configurable PWM modules. COG handles dead-band generation and blanking for half-bridge gate drivers, eliminating timing-critical software routines. The NCO (Numerically Controlled Oscillator) provides fine-grained stepper microstepping rates beyond standard PWM resolution. With 7KB Flash, sensorless BEMF startup routines fit comfortably, while the on-chip comparators detect zero-cross events for back-EMF sensing. The extended -40C to +125C range supports under-hood automotive auxiliaries like fuel-pump or HVAC damper motors.
Recommended
Consumer Appliance Control Board
Consumer appliances such as coffee machines, washing machines, and air purifiers benefit from the PIC16F1713-E/MV's combination of analog integration, low power, and compact UQFN-28 footprint. The PIC core runs user-interface state machines, the 10-bit ADC reads temperature and pressure sensors, and the EUSART/SPI/I2C peripherals connect to Wi-Fi or BLE modules for smart-appliance variants. The 7KB Flash accommodates BLE provisioning state machines, while the CLC handles safety interlocks like lid-open detection in hardware. The compact 4x4 mm package fits the space-constrained PCBs typical of small kitchen appliances.
Recommended
Smart Meter / Energy Monitor
The PIC16F1713-E/MV is a candidate for single-phase smart meter and energy-monitoring designs that combine metrology computation with communication. The 10-bit ADC with computation engine performs RMS voltage and current measurements while the NCO generates the metrology sampling clock. The ZCD peripheral detects AC line zero-crossings for synchronized sampling without CPU intervention. With 7KB Flash, the meter can run calibration, tamper detection, and DLMS/COSEM or Modbus stacks. The AEC-Q100 qualification and -40C to +125C range support outdoor meter cabinets and industrial energy-monitoring installations.
Recommended
Touch-Sense User Interface
The PIC16F1713-E/MV's high-speed comparators and CLC peripheral implement capacitive touch-sense buttons and sliders without dedicated touch ICs. The comparators detect capacitance changes on sense pads while the CLC generates the charge/discharge timing. Software libraries from Microchip (mTouch) provide proven firmware for slider position decoding. The 7KB Flash holds 8-12 touch buttons with gesture recognition, and the 28-UQFN package supports thin panel-mount designs. Combined with the on-chip op-amps, the same MCU can also read ambient light sensors for automatic backlight dimming.
Recommended
Recommended Products Summary
Engineering reference data for PIC16F1713-E/MV — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | PIC16F1713-I/MV | PIC16F1716-I/MV | PIC16F15356-I/MV | PIC16F1709-I/SS |
|---|---|---|---|---|---|
| Package | 28-UQFN (4x4) MV | 28-UQFN (4x4) MV | 28-UQFN (4x4) MV | 28-UQFN (4x4) MV | 28-SSOP - different package |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory | 7 KB Flash | 7 KB Flash | 14 KB Flash | 28 KB Flash | 14 KB Flash |
| RAM Size | 512 B | 512 B | 1 KB | 2 KB | 1 KB |
| Data EEPROM | 0 B | 0 B | 1 KB | 0 B | 0 B |
| Maximum Clock | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| AEC-Q100 Grade | Qualified (Grade 1, -40C to +125C) | Not AEC-Q100 (Industrial -40C to +85C) | Not AEC-Q100 (Industrial -40C to +85C) | Not AEC-Q100 (Industrial -40C to +85C) | Not AEC-Q100 (Industrial) |
| On-Chip Op-Amps | Yes (2x) | Yes (2x) | Yes (2x) | Yes (3x) | Yes (2x) |
| CIP Peripherals | CLC, COG, NCO, ZCD | CLC, COG, NCO, ZCD | CLC, COG, NCO, ZCD | CLCx4, NCOx2, COG | CLC, NCO, COG |
| Approx. Unit Price (1k qty) | USD 1.38 | USD 1.20 (est.) | USD 1.55 (est.) | USD 1.65 (est.) | USD 1.45 (est.) |
Key Differentiators
- AEC-Q100 Grade 1 qualification in compact 4x4 mm UQFN (vs PIC16F1713-I/MV)
- On-chip operational amplifiers eliminate external analog ICs (vs PIC16F15356-I/MV)
- Complete CIP suite (CLC+COG+NCO+ZCD) for hardware-offloaded tasks (vs PIC16F1516-I/ML)
Design Notes
The PIC16F1713-E/MV operates from 2.5V to 5.5V, but maximum clock frequency derates with supply voltage: full 32MHz requires 3.0V or higher, while 16MHz operation is permitted down to 2.5V. For battery applications using a single LiSOCl2 cell or 2x AA alkaline, a boost converter or step-up regulator is required to maintain 3V+. Consider the MCP1640 boost converter or MCP1700 LDO for low-Iq regulation. Estimated: at 3.3V and 32MHz active mode, core current is approximately 6 mA, dropping below 1 uA in nanoWatt sleep mode.
The 28-UQFN (MV) package has an exposed thermal pad (EP) that must be soldered to the PCB ground plane for mechanical reliability and thermal dissipation. Connect the EP to VSS with multiple thermal vias to the inner ground plane. UQFN packages have finer pitch than QFN (0.4mm typical); use NSMD pads with via-in-pad for best solder-joint reliability. Avoid placing signal traces under the EP to prevent solder-wicking during reflow.
Place the 0.1 uF VDD decoupling capacitor within 3 mm of the VDD pin and a 10 uF bulk capacitor near the IC. Keep analog inputs (RA0-RA5, RB1-RB5) away from high-current switching traces and digital outputs to minimize crosstalk. The ADC's reference voltage (VREF+ pin) should be bypassed with a separate 0.1 uF + 10 uF capacitor pair if used; otherwise tie to VDD. Route the ICSP clock (ICSPCLK) and data (ICSPDAT) traces straight and short to facilitate in-circuit programming.
Common pitfalls when designing with the PIC16F1713-E/MV: (1) Forgetting the CONFIG words - the device ships blank and will not execute code without proper configuration register programming; (2) Using the internal 32MHz HFINTOSC without OSCTUNE calibration degrades UART baud-rate accuracy; (3) Configuring PPS without also setting the corresponding TRIS bit - PPS routing requires the pin to be configured as input or output first; (4) Driving the MCLR pin low inadvertently through leakage current - always use the internal MCLR disabled mode unless external reset is required; (5) Not using the CLC for safety interlocks - hardware logic is more reliable than polled software checks.
Compliance Information
RoHS compliant per Microchip product page. AEC-Q100 Grade 1 qualified (operating temperature -40C to +125C) for automotive applications. Lead-free and halogen-free per Microchip material declaration.
