PIC16LF1936T-I/SO - 14KB Flash 8-bit MCU | Microchip | SOIC-28
MPN: PIC16LF1936T-I/SO ✓ Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $3.62 | $3.62 |
| 10 | $3.21 | $32.10 |
| 100 | $2.86 | $286.00 |
| 500 | $2.55 | $1,275.00 |
| 1,000 | $2.27 | $2,270.00 |
PIC16LF1936T-I/SO Overview
A PIC microcontroller is a programmable system-on-a-chip combining an 8-bit RISC CPU core, non-volatile flash program memory, SRAM, EEPROM data memory, and a rich set of analog and digital peripherals in a single IC. The PIC16LF1936 belongs to Microchip's enhanced mid-range family, sitting in the hierarchy PIC16LF1936 -> PIC16F1936 family -> PIC16 8-bit MCU family -> PIC microcontroller -> microcontroller -> embedded computing. The 'LF' prefix denotes the low-voltage F-process variant that supports the industry's broadest operating voltage range and the nanoWatt XLP technology.
Key features include 14KB flash program memory (8K x 14 words), 512B SRAM, 256B EEPROM, integrated LCD driver supporting up to 96 segments, 11-bit ADC with up to 17 channels, multiple timers, and nanoWatt XLP sleep currents down to 20 nA. The wide 1.8V to 5.5V VDD range allows direct connection to single-cell Li-ion, 3.3V, and 5V rails without level shifters.
The PIC16LF1936 is built on Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, two hardware stack levels for interrupt handling, and a single-cycle instruction architecture at 32 MHz. The integrated LCD driver supports static, 1/2, 1/3, and 1/4 multiplexed LCD glass with on-chip charge pump, eliminating external voltage generation. Compared with the PIC16F1936, the LF variant trades absolute maximum VDD headroom for a much wider operating range and lower quiescent current.
Typical applications include battery-powered consumer devices, metering and instrumentation with LCD readout, white goods and appliance control, sensor signal conditioning nodes, and IoT edge nodes with segmented LCD displays. Its low sleep current also makes it well suited to remote controls and energy-harvesting wireless sensor nodes.
When designing with this part, route the ICSPCLK/ICSPDAT lines to a dedicated programming header for in-circuit serial programming and place a 100 nF decoupling capacitor within 5 mm of each VDD/VDDCORE pin pair to meet the datasheet's noise budget. Use the on-board MCLR internal pull-up option to free the MCLR pin as an input when no external reset is required.
This page synthesizes distributor stock and pricing, drop-in same-package alternatives, and design guidance that consolidates engineering decision points not present on a single manufacturer datasheet page.
Drop-in alternatives for PIC16LF1936T-I/SO — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with PIC16LF1936T-I/SO (same form factor and footprint) — differing in ADC, Package, RoHS Status, Timers, Program Memory (Flash).
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
PIC16LF1936-I/SO
✅ Drop-In📋 Reference alternative (not in catalog)
PIC16LF1936-E/SO
✅ Drop-In✓ In Stock
$1.71 / Unit
View Datasheet →PIC16LF1936T-I/SS
✅ Drop-In📋 Reference alternative (not in catalog)
PIC16F1936T-I/SO
✅ Drop-In📋 Reference alternative (not in catalog)
PIC16LF1936T-I/SO Maximum Ratings & Electrical Characteristics
| Core Architecture | PIC 8-bit enhanced mid-range |
| Program Memory (Flash) | 14 KB (8K x 14 words) |
| Data SRAM | 512 B |
| Data EEPROM | 256 B |
| Maximum CPU Speed | 32 MHz |
| Operating Voltage Range | 1.8 V to 5.5 V |
| I/O Pins (max) | 36 |
| Integrated LCD Driver | Yes, up to 96 segments |
| ADC | 11-bit, up to 17 channels |
| Timers | 5 (Timer0, Timer1, Timer2, Timer4, Timer6) |
| nanoWatt XLP Technology | Yes |
| Package | SOIC-28 (SO), 7.50 mm wide body |
| Mounting Type | Surface Mount |
| Operating Temperature | -40C to +85C (Industrial) |
| ROM Type | Flash |
| RoHS Status | Compliant (LEAD FREE) |
PIC16LF1936T-I/SO Pin Configuration
| Pin 1 | RA0/AN0/SEG12 — PORTA bit 0 / Analog input 0 / LCD SEG12 |
| Pin 2 | RA1/AN1/SEG7 — PORTA bit 1 / Analog input 1 / LCD SEG7 |
| Pin 3 | RA2/AN2/VREF-/COM2 — PORTA bit 2 / Analog input 2 / VREF- / LCD COM2 |
| Pin 4 | RA3/AN3/VREF+/COM3 — PORTA bit 3 / Analog input 3 / VREF+ / LCD COM3 |
| Pin 5 | RA4/T0CKI/C1OUT/SEG4 — PORTA bit 4 / Timer0 clock input / Comparator 1 output / LCD SEG4 |
| Pin 6 | RA5/AN4/C2OUT/SEG5 — PORTA bit 5 / Analog input 4 / Comparator 2 output / LCD SEG5 |
| Pin 7 | RA6/OSC2/CLKR — PORTA bit 6 / Oscillator output / Clock output |
| Pin 8 | RA7/OSC1/CLKIN — PORTA bit 7 / Oscillator input / External clock input |
| Pin 9 | VSS — Ground reference |
| Pin 10 | VDD — Positive supply voltage |
| Pin 11 | RB0/AN12/INT0/SEG0 — PORTB bit 0 / Analog input 12 / External interrupt 0 / LCD SEG0 |
| Pin 12 | RB1/AN10/INT1/SEG1 — PORTB bit 1 / Analog input 10 / External interrupt 1 / LCD SEG1 |
| Pin 13 | RB2/AN8/INT2/SEG2 — PORTB bit 2 / Analog input 8 / External interrupt 2 / LCD SEG2 |
| Pin 14 | RB3/AN9/CCP5/SEG3 — PORTB bit 3 / Analog input 9 / CCP5 / LCD SEG3 |
| Pin 15 | RB4/AN11/SEG11 — PORTB bit 4 / Analog input 11 / LCD SEG11 |
| Pin 16 | RB5/SEG10 — PORTB bit 5 / LCD SEG10 |
| Pin 17 | RB6/ICSPCLK/SEG9 — PORTB bit 6 / ICD clock / LCD SEG9 |
| Pin 18 | RB7/ICSPDAT/SEG8 — PORTB bit 7 / ICD data / LCD SEG8 |
| Pin 19 | VSS — Ground reference |
| Pin 20 | VDD — Positive supply voltage |
| Pin 21 | RC0/SOSCO/SCLKI — PORTC bit 0 / Secondary oscillator output / External clock input |
| Pin 22 | RC1/SOSCI — PORTC bit 1 / Secondary oscillator input |
| Pin 23 | RC2/CCP1/SEG6 — PORTC bit 2 / CCP1 / LCD SEG6 |
| Pin 24 | RC3/SEG13/CCP2 — PORTC bit 3 / LCD SEG13 / CCP2 |
| Pin 25 | RC4/SEG14 — PORTC bit 4 / LCD SEG14 |
| Pin 26 | RC5/SEG15 — PORTC bit 5 / LCD SEG15 |
| Pin 27 | RC6/SEG16/TX/CK — PORTC bit 6 / LCD SEG16 / UART TX / I2C clock |
| Pin 28 | RC7/SEG17/RX/DT — PORTC bit 7 / LCD SEG17 / UART RX / I2C data |
Typical Applications
PIC16LF1936T-I/SO is suitable for 6 applications: Battery-Powered Consumer Devices, Metering and Instrumentation with LCD, White Goods and Appliance Control, Sensor Signal Conditioning Nodes, IoT Edge Nodes with Segmented LCD, Remote Control and HMI.
Battery-Powered Consumer Devices
The PIC16LF1936T-I/SO's 1.8 V to 5.5 V operating range and nanoWatt XLP technology with sleep currents down to 20 nA make it ideal for single-cell coin-cell and Li-ion battery applications. Placed directly on the battery rail without a boost converter, it provides 14 KB flash for application firmware and 256 B EEPROM for user settings while preserving battery life over multi-year deployments. Compared with the PIC16F1936, the LF variant extends usable battery capacity by operating deeper into the cell's discharge curve.
Recommended
Metering and Instrumentation with LCD
The PIC16LF1936T-I/SO integrates a 96-segment LCD driver with on-chip charge pump, eliminating external bias-voltage generation for gas, water, and electricity meters. With 14 KB flash, 512 B SRAM, and a 11-bit ADC, it can run the metering algorithm, drive the segmented display, and handle tamper detection all from a single chip. The wide 1.8-5.5V VDD range supports battery or supercapacitor-backed designs per the Microchip datasheet.
Recommended
White Goods and Appliance Control
The PIC16LF1936T-I/SO's 36 I/O pins, integrated LCD driver, and 1.8-5.5V operating range make it well suited to washing machines, dishwashers, and microwave oven front panels. The MCU drives the user interface, segmented LCD, sensor inputs, and motor-control relays while running the safety supervisor firmware. Industrial -40C to +85C temperature grade ensures reliable operation in appliance environments per the Microchip datasheet.
Recommended
Sensor Signal Conditioning Nodes
The PIC16LF1936T-I/SO's 11-bit ADC with up to 17 channels and 256B EEPROM for calibration storage enables distributed analog sensor nodes. With 32 MHz CPU speed and enhanced mid-range core, it handles linearization and averaging while the nanoWatt XLP sleep currents extend battery life in duty-cycled sensing applications. Industrial temperature grade supports outdoor deployments per the Microchip datasheet.
Recommended
IoT Edge Nodes with Segmented LCD
The PIC16LF1936T-I/SO's integrated LCD driver and nanoWatt XLP sleep mode make it ideal for IoT edge nodes that need a status or measurement display. With 14 KB flash, it can implement a small wireless protocol stack via SPI-connected radio while driving the LCD in real time. The 1.8-5.5V VDD range simplifies integration with coin-cell and rechargeable battery systems per the Microchip datasheet.
Recommended
Remote Control and HMI
The PIC16LF1936T-I/SO's low sleep current, integrated LCD, and small SOIC-28 footprint suit remote controls and handheld HMI panels with segmented displays. The enhanced mid-range core with 14-bit instruction word and 32 MHz CPU provides responsive key handling and LCD updates, while nanoWatt XLP technology extends coin-cell battery life for multi-year deployments per the Microchip datasheet.
Recommended
Recommended Products Summary
Engineering reference data for PIC16LF1936T-I/SO — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | PIC16LF1936-I/SO | PIC16LF1936-E/SO | PIC16LF1936T-I/SS | PIC16F1936T-I/SO |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SOIC-28 (SO) | SOIC-28 (SO) - same | SOIC-28 (SO) - same | SSOP-28 (SS) - same pinout, smaller body | SOIC-28 (SO) - same |
| Flash Program Memory | 14 KB | 14 KB | 14 KB | 14 KB | 14 KB |
| SRAM | 512 B | 512 B | 512 B | 512 B | 512 B |
| Operating Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Max CPU Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Temperature Grade | -40C to +85C (Industrial) | -40C to +85C | -40C to +125C (Extended) | -40C to +85C | -40C to +85C |
| Integrated LCD Driver | Yes (96 segments) | Yes (96 segments) | Yes (96 segments) | Yes (96 segments) | Yes (96 segments) |
Key Differentiators
- Single-chip LCD driver integration (vs PIC16LF1906-I/SP)
- Widest VDD operating range in the family (vs PIC16F1936T-I/SO)
- SOIC-28 wide-body for hand-soldered prototypes (vs PIC16LF1936T-I/SS)
Design Notes
Place a 100 nF decoupling capacitor within 5 mm of each VDD pin and a single 10 uF bulk capacitor on the supply rail. The PIC16LF1936 has multiple VSS/VDD pairs on the 28-pin SOIC; bypassing each VDD independently minimizes MCU supply-noise coupling into the analog ADC measurements.
The PIC16LF1936 differs from the PIC16F1936 in voltage-class ratings and XLP behavior. When migrating from F to LF, verify that the LF datasheet's VDD min at 32 MHz (3.0 V) is met by your supply. Also ensure that the LF sleep current specification (per nanoWatt XLP datasheet) is read from the LF document, not the F one.
Route the ICSPCLK and ICSPDAT signals (RB6/RB7) to a 6-pin in-circuit serial programming header with a 4.7 kohm pull-up on MCLR. Keep the ICSP traces short and isolated from high-current switching nodes. The RB6/RB7 pins default to ICD functions after reset, so any user application driving RB6/RB7 must yield during programming per the Microchip datasheet.
Compliance Information
RoHS-compliant LEAD FREE per Microchip product page. Not AEC-Q100 qualified - choose extended-temperature variants for harsh environments. Halogen-free status not explicitly stated in retrieved web data.
