Microcontroladores

Produtos (18743)

ATSAME53J18A-AF - 120MHz Cortex-M4F MCU 256KB Flash 64-TQFP
ATSAME53J18A-AF

ATSAME53J18A-AF - 120MHz Cortex-M4F MCU 256KB Flash 64-TQFP

The Microchip Technology ATSAME53J18A-AF is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family running up to 120 MHz with a single-precision Floating Point Unit (FPU), 256 KB of dual-panel Flash with ECC, and 128 KB of SRAM with ECC, housed in a 64-pin TQFP (10x10 mm) package rated for extended industrial temperature. What is a Cortex-M4F microcontroller? A Cortex-M4F microcontroller is a 32-bit MCU core built on the ARMv7-M architecture with hardware single-precision floating point, deterministic interrupt handling, and a Thumb-2 instruction set, positioning it in the hierarchy MCU -> embedded processor -> microcontroller -> semiconductor. The 'F' suffix denotes an integrated FPU, which accelerates floating-point DSP and control-loop math versus integer-only M-class cores. Key features of the ATSAME53J18A-AF include a 10/100 Mbps Ethernet MAC with IEEE 1588 PTP timestamping, a USB 2.0 Full-Speed device/host interface, a high-speed SD/MMC host controller, two I2S interfaces for digital audio, up to six SERCOM configurable serial channels (UART/SPI/I2C), a 12-bit 1 Msps ADC, dual analog comparators, and a hardware Cryptographic Accelerator (AES/SHA/TRNG). The 64-TQFP package gives access to 51 GPIO lines and supports the SAME53 automotive and Extended grade temperature grading (100/125C). Architecturally, the SAM E53 integrates a multi-layer bus matrix (AHB/APB) with separate Flash and SRAM ports to allow zero-wait-state 120 MHz operation while the Ethernet MAC and Crypto accelerator perform DMA concurrently. The dual-panel Flash and SRAM with ECC support industrial functional-safety requirements and improve Flash endurance versus single-panel designs. Typical applications include industrial Ethernet gateways, IoT edge nodes with secure cloud connectivity, USB Human Interface Devices (HID), building automation controllers, smart energy metering, and connected motor-control front-ends. The on-chip 10/100 Ethernet MAC eliminates the need for an external PHY-controller ASIC in cost-sensitive nodes. When designing with this MCU, plan the pin map for either Ethernet RMII or USB HS usage, since they share SERCOM and GPIO resources. The 64-TQFP requires a 4-layer PCB with continuous power-plane under the exposed pad to meet thermal and EMI requirements for industrial certification.

Cotação Contato
ATSAME53J18A-AFT - 120MHz Cortex-M4F MCU, 256KB Flash, 64-TQFP | Microchip
ATSAME53J18A-AFT

ATSAME53J18A-AFT - 120MHz Cortex-M4F MCU, 256KB Flash, 64-TQFP | Microchip

The Microchip Technology ATSAME53J18A-AFT is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 high-performance series, operating at up to 120 MHz with a single-precision Floating Point Unit (FPU). It integrates 256 KB of Flash with ECC, 128 KB of SRAM with ECC, and a 10/100 Ethernet MAC in a 64-pin TQFP (10x10 mm) package. The device targets industrial connectivity, IoT gateways, and graphical HMI applications that need deterministic real-time performance. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals on one die. The ARM Cortex-M4F is a 32-bit processor core with DSP extensions and a hardware FPU, positioned between the Cortex-M3 (no FPU) and Cortex-M7 (higher performance). Within the broader taxonomy, the ATSAME53J18A belongs to the Cortex-M4F class -> ARM Cortex-M family -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. The "SAM E" series from Microchip is engineered for mixed-signal industrial designs with on-chip high-speed ADCs, USB, CAN-FD, and Ethernet. Key features of the ATSAME53J18A include a Cortex-M4F core with FPU at 120 MHz, 256 KB dual-panel Flash with ECC, 128 KB SRAM with ECC, 10/100 Ethernet MAC, USB 2.0 Full-Speed, CAN-FD, a 12-bit 1 MSPS ADC, and multiple SERCOM (serial communication) interfaces. The Cortex-M4F core adds DSP instructions and single-precision FPU support, enabling efficient execution of sensor-fusion algorithms and audio processing in firmware. The device operates from 1.71 V to 3.6 V across an industrial temperature range of -40C to +125C. The SAM E53 series uses a dual-panel Flash architecture that allows simultaneous read-while-write, enabling live firmware updates without halting code execution. The integrated Ethernet MAC with IEEE 1588 PTP hardware timestamping and the on-chip high-speed USB make the part well-suited for connected industrial nodes. A 12-bit 1 MSPS ADC and two 12-bit 1 MSPS DACs provide analog front-end capability, while the CryptoCell (TRNG, AES, SHA) variants support secure-boot and TLS acceleration on similar siblings. Typical applications include industrial Ethernet gateways, building-automation controllers, USB peripherals, sensor hubs with on-chip DSP conditioning, graphical HMIs with TFT drives on sibling parts, and connected medical devices. The combination of Ethernet + USB + CAN-FD makes this MCU a common choice for protocol-conversion bridges. The 64-TQFP footprint also supports hand-solderable prototyping. When designing with the ATSAME53J18A-AFT, ensure the 64-TQFP land pattern matches the -AU (Tray) variant if you need to swap packaging. Decoupling: place a 100 nF X7R capacitor on each VDD pin and a bulk 4.7 uF near the package. For Ethernet, the integrated MAC requires an external PHY such as the KSZ8081 and 49.9 ohm 1% termination resistors. Configure unused pins as outputs driven low to minimize current draw. This page synthesizes distributor pricing tiers, drop-in same-package alternatives from the SAM E53 family, and practical design notes not found in the standalone Microchip datasheet.

Cotação Contato
ATSAME53J18A-AU - 120MHz Cortex-M4F MCU 256KB Flash | Microchip
ATSAME53J18A-AU

ATSAME53J18A-AU - 120MHz Cortex-M4F MCU 256KB Flash | Microchip

The Microchip Technology ATSAME53J18A-AU is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with a single-precision Floating Point Unit (FPU), 256 KB of Flash, and 128 KB of SRAM, housed in a 64-pin TQFP (10x10 mm) package qualified for -40C to +85C operation. The part integrates a 10/100 Mbps Ethernet MAC, a USB 2.0 Full-Speed device/host controller, a High-Speed USB port, a CAN-FD controller, and a 12-bit 1 Msps ADC with up to 16 channels, targeting connected industrial and IoT edge nodes. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile memory (SRAM), non-volatile memory (Flash), and a rich set of peripherals such as timers, communication controllers, and analog blocks. Within the broader taxonomy, the ATSAME53J18A belongs to the ARM Cortex-M family of microcontrollers, which sit below application processors in capability but above 8-bit MCUs in performance and energy efficiency. Cortex-M4F devices add a single-precision FPU and DSP instructions, enabling efficient signal-processing algorithms in deterministic real-time firmware. Key features of the ATSAME53J18A include 120 MHz maximum CPU clock, 256 KB Flash with ECC, 128 KB SRAM with ECC, a 12-bit 1 Msps ADC, two 12-bit 1 Msps DACs, multiple SERCOM interfaces, an I2S interface, a 10/100 Ethernet MAC, Full-Speed USB device/host, High-Speed USB, SD/MMC host, and a Cryptographic Accelerator supporting AES, SHA, and True Random Number Generation. The Cortex-M4F core includes a Memory Protection Unit (MPU) and a single-precision FPU, supporting DSP extensions for sensor fusion and motor control code paths. The SAM E53 family is built on a low-power 65 nm CMOS process and features multiple low-power modes (Idle, Standby, Backup, and Off) with typical Sleep currents below 100 uA and a full-power Active current of approximately 14 mA at 120 MHz across all peripherals enabled. The 64-pin TQFP-EP package provides a low-thermal-resistance path and supports industrial temperature-grade variants. Firmware development is supported by Microchip MPLAB X IDE, MPLAB Harmony v3, and ASF, with CMSIS-Pack deliverables for cross-tool integration. Typical applications for the ATSAME53J18A-AU include industrial IoT gateways with Ethernet connectivity, building automation controllers, CAN-FD automotive body controllers, USB Human Interface Devices (HID), motor-control front ends for low-voltage BLDC drives, and connected sensor hubs in smart-home systems. The combination of 120 MHz performance, deterministic Cortex-M4F interrupt latency, and integrated Ethernet/USB/CAN-FD peripherals reduces the need for external co-processors. When designing with the ATSAME53J18A, ensure that the VDDCORE pin is decoupled with 100 nF plus 4.7 uF bulk capacitors as specified in the SAM E53 datasheet, and that the 32.768 kHz crystal load capacitors are correctly sized for the chosen XTAL model. Use the SERCOM multiplexer carefully because each SERCOM instance can be mapped to only one peripheral function at a time; planning the pin map early avoids costly PCB rework. This page consolidates distributor pricing, drop-in alternatives from the SAME53 family, and practical design notes that are not duplicated in the Microchip datasheet, helping engineers shorten component selection and BOM validation cycles.

Cotação Contato
ATSAME53J18A-AU-EFP - 120MHz Cortex-M4F MCU 256KB Flash | Microchip
ATSAME53J18A-AU-EFP

ATSAME53J18A-AU-EFP - 120MHz Cortex-M4F MCU 256KB Flash | Microchip

The Microchip Technology ATSAME53J18A-AU-EFP is a 32-bit ARM Cortex-M4F microcontroller running at 120 MHz with Floating Point Unit (FPU), 256 KB of dual-panel Flash with ECC, and 128 KB of SRAM, housed in a 64-pin TQFP (10x10 mm) package. It is a member of the SAM E53 family of high-performance microcontrollers targeting industrial connectivity and Human-Machine Interface (HMI) applications. What is a microcontroller (MCU)? A microcontroller is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals (GPIO, timers, ADC, communication interfaces). The Cortex-M4F architecture is a Harvard-bus 32-bit core optimized for embedded real-time control, with hardware single-precision floating point and DSP extensions, fitting into the broader taxonomy: MCU -> microcontroller -> embedded processor -> semiconductor. Key features of the ATSAME53J18A-AU-EFP include 256 KB Flash with ECC and dual-panel support for safe in-application updates, 120 MHz core clock, integrated 10/100 Mbps Ethernet MAC, USB 2.0 Full-Speed with on-chip PHY, an I2S audio interface, a 12-bit 1 MSPS ADC, and a Parallel Capture Interface for camera or display input. The 'EFP' suffix indicates Extended Flash Performance and a Tray packaging option, while the 'AU' suffix denotes an automotive-grade (-40C to +85C) operating range. The device integrates a sophisticated peripherals set including a QSPI interface for external memory, multiple SERCOM (UART/SPI/I2C) channels, an on-chip 12-bit DAC, CAN-FD, and a Pixel Read/Wait signal interface for TFT displays. The architecture supports 5 V tolerant I/O on selected pins and includes an Event System for deterministic inter-peripheral signaling without CPU intervention, a hallmark of the SAM family. Typical applications include industrial building automation gateways, IoT edge nodes with Ethernet connectivity, automotive dashboard controllers, HMI panels with TFT displays, and connected sensor hubs. The combination of Ethernet MAC and USB makes the ATSAME53J18A-AU-EFP particularly attractive for industrial IoT bridges that aggregate sensor data and forward it to the cloud. When designing with this part, ensure the 64-pin TQFP land pattern supports the 10x10 mm footprint and route the Ethernet differential pairs with 100-ohm controlled impedance. The internal 1.2V LDO core regulator requires bulk capacitance near the VCORE pin for stable operation at 120 MHz. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single resource for component selection.

Cotação Contato
ATSAME53J18A-AUT - 120MHz Cortex-M4F 256KB Flash MCU | Microchip
ATSAME53J18A-AUT

ATSAME53J18A-AUT - 120MHz Cortex-M4F 256KB Flash MCU | Microchip

The Microchip Technology ATSAME53J18A-AUT is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family, running up to 120 MHz with an integrated Floating Point Unit (FPU), 256 KB of Flash memory, and 128 KB of SRAM, housed in a 64-pin TQFP (10x10 mm) package supplied on tape and reel. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash for code, SRAM for data), and a rich set of peripherals on one die. The ARM Cortex-M4F is a mainstream 32-bit MCU core featuring a single-precision IEEE 754 FPU, DSP extensions, and deterministic interrupt handling, making it a workhorse for connected embedded products. The SAM E53 line sits above Cortex-M0+/M23 entry-level parts but below Cortex-M7 high-performance parts, occupying the mid-to-high end of Microchip's SAM portfolio alongside the SAM D51 and SAM E54 cousins. Key features include 120 MHz CPU core speed, 256 KB Flash with ECC, 128 KB SRAM with ECC, 24-channel 12-bit ADC, two 12-bit DAC outputs, a 10/100 Ethernet MAC, a USB 2.0 Full-Speed device/host controller, multiple SERCOM interfaces (configurable as UART/SPI/I2C), and an integrated 32 kHz low-power RTC. The 64-pin TQFP package gives broad GPIO access for a wide variety of analog and digital peripherals while remaining hand-solderable for prototyping. Architecturally, the SAM E53 combines a Cortex-M4F core with a multi-layer AHB/APB bus matrix that allows simultaneous DMA-driven peripheral activity (Ethernet, USB, ADC) without CPU intervention, plus an EVENT system for low-latency inter-peripheral signaling. The integrated FPU and DSP instructions allow the same firmware to perform audio decoding, sensor fusion, or motor control loops in a single MCU, eliminating external DSP chips. Typical applications include industrial Ethernet gateways, building automation controllers, USB Human Interface Devices (HIDs), audio playback and processing modules, and connected sensor hubs. The integrated Ethernet MAC makes it especially attractive for IoT edge nodes that must bridge a local sensor bus to a TCP/IP network without an external PHY companion. When laying out the ATSAME53J18A-AUT, place the 0.1 µF decoupling capacitors within five V of every VDD/VDDIO pin pair and route the USB D+/D- traces as a 90-ohm differential pair. Enable the on-chip voltage regulator with the recommended 1 µF + 100 nF bulk cap on VDDOUT to avoid LDO startup issues. This page synthesizes distributor stock and pricing, drop-in pin-compatible alternatives within the SAM E53 family, and practical layout guidance not aggregated in the bare datasheet, giving procurement and design engineers a single decision-ready view.

Cotação Contato
ATSAME53J18A-MF - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip
ATSAME53J18A-MF

ATSAME53J18A-MF - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip

The Microchip Technology ATSAME53J18A-MF is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family, running up to 120 MHz with a single-precision Floating Point Unit (FPU) and DSP extensions, housed in a 64-pin QFN (9x9 mm) package with exposed thermal pad. The device integrates 256 KB of Flash with ECC and 128 KB of SRAM, and includes a 10/100 Ethernet MAC, USB 2.0 Full-Speed device/host, and a CAN-FD controller aimed at connected industrial and IoT gateway designs. What is a Cortex-M4F microcontroller? An ARM Cortex-M4F MCU is a low-power 32-bit microcontroller core with hardware single-precision floating-point and DSP instructions, designed for deterministic real-time embedded control. The Cortex-M4F sits within the broader ARM Cortex-M family (Cortex-M0/M0+/M3/M4/M7) and is widely used in motor control, industrial automation, audio processing, and connected sensor nodes where floating-point math and signal processing are needed. Key features of the ATSAME53J18A-MF include a 120 MHz core, 256 KB dual-panel Flash with ECC, 128 KB SRAM, a 12-bit 1 MSPS ADC, two 12-bit DACs, multiple SERCOM (serial communication) interfaces configurable as UART/SPI/I2C, an on-chip 10/100 Ethernet MAC with IEEE 1588 PTP support, USB 2.0 Full-Speed, CAN-FD, and an integrated PTC (Peripheral Touch Controller) for capacitive touch sensing. The 64-QFN package exposes up to 51 GPIO lines for peripheral expansion. Architecture-wise, the ATSAME53J18A-MF uses a Harvard-bus Cortex-M4F core with a tightly coupled 4 KB instruction cache, single-cycle MAC, and a Memory Protection Unit (MPU). The dual-panel Flash with ECC and SRAM with ECC enhance functional safety, making the part suitable for IEC 60730 class-B aware designs. The Event System, SERCOM, and configurable logic peripherals allow flexible pin-mapping and event-driven response without CPU overhead. Typical applications include industrial Ethernet gateways, building automation controllers, USB-to-UART/CAN bridges, capacitive touch human-machine interfaces (HMIs), low-end motor control, and connected sensor nodes with Ethernet or USB connectivity. The wide operating temperature range and integrated peripherals reduce external component count for these designs. When designing with the ATSAME53J18A-MF, ensure that the 64-QFN exposed pad is soldered to a sufficient ground copper pour for thermal dissipation and signal integrity, and that decoupling capacitors are placed close to each VDD pin. Programming is supported through SWD or the Atmel/Microchip bootloader, and development can be done in Microchip Studio (ASF) or MPLAB X with the Harmony 3 framework.

Cotação Contato
ATSAME53J18A-MFT - 120MHz ARM M4F MCU 256KB Flash | Microchip
ATSAME53J18A-MFT

ATSAME53J18A-MFT - 120MHz ARM M4F MCU 256KB Flash | Microchip

The Microchip Technology ATSAME53J18A-MFT is a 32-bit ARM Cortex-M4F microcontroller with Floating Point Unit (FPU) running up to 120 MHz, integrating 256 KB of Flash and 256 KB of SRAM with ECC in a 64-pin QFN (9x9 mm) package with exposed pad. It belongs to the SAM E53 family, part of the broader SAM D5X/E5X Cortex-M4 platform, and is rated for the extended industrial temperature range of -40C to +125C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O into one package. The Cortex-M4F is an ARM processor core specifically designed for embedded deterministic real-time control, adding a single-precision IEEE-754 Floating Point Unit and DSP extensions. Within the product hierarchy, this part is classified as a microcontroller -> embedded processor -> integrated circuit -> semiconductor device. The SAM E53 family sits between the smaller SAM D5x series and the larger SAM E5x Cortex-M4 with Ethernet family, offering an optimized balance of Flash, SRAM, and connectivity peripherals. Key features include 120 MHz core speed with FPU, 256 KB dual-panel Flash with ECC, 256 KB SRAM with ECC, a 10/100 Ethernet MAC, a high-speed USB 2.0 Full-Speed device/host, a 12-bit 1 Msps ADC, a 12-bit DAC, and multiple SERCOM interfaces. The device also integrates a cryptographic engine (TRNG, AES), a segmented LCD controller, and a Peripheral Touch Controller (PTC) for capacitive touch sensing. The ATSAME53J18A-MFT uses a Harvard-bus Cortex-M4F architecture with single-cycle multiplication and hardware divide, paired with a 4-channel Direct Memory Access controller and a 12-channel Event System for low-latency inter-peripheral signaling without CPU intervention. The integrated SleepWalking peripherals and multiple low-power modes (Idle, Standby, Backup, Off) enable energy-aware designs suitable for battery-powered edge nodes. Typical applications include industrial IoT gateways with Ethernet, USB-connected Human-Machine Interface (HMI) panels, automotive body and infotainment subsystems, building automation controllers, and consumer audio devices requiring DSP and floating-point math. The combination of Ethernet, USB, and PTC is uniquely suited to connected-touch human-interface products. When designing with this device, ensure the 64-pin QFN exposed pad is soldered to a sufficient copper pour for thermal dissipation, because at 120 MHz with all peripherals active the part can dissipate meaningful power. Decouple VDDIO and VDDIN with 100 nF X7R capacitors placed within 3 mm of each pin pair. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, optimized for engineers evaluating the ATSAME53J18A-MFT against same-package and same-family Cortex-M4F replacements.

Cotação Contato
ATSAME53J18A-MU - 120MHz Cortex-M4F MCU 256KB Flash | Microchip
ATSAME53J18A-MU

ATSAME53J18A-MU - 120MHz Cortex-M4F MCU 256KB Flash | Microchip

The Microchip Technology ATSAME53J18A-MU is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family, running up to 120 MHz with an integrated Floating Point Unit (FPU), 256 KB of Flash, and 128 KB of SRAM, housed in a 64-pin QFN (9x9 mm) package. The device features a 10/100 Ethernet MAC, a high-speed USB 2.0 interface, and a rich peripheral set including SERCOM, I2S, and a 12-bit ADC, all backed by ECC-protected memory. What is a Cortex-M4F microcontroller? A microcontroller (MCU) is a single-chip computer containing a CPU core, memory, and peripherals. The Cortex-M4F is ARM's mainstream 32-bit core with DSP instructions and a single-precision Floating Point Unit, sitting above Cortex-M0/M3 and below Cortex-M7 in performance. SAM E53 microcontrollers target industrial IoT, connected appliances, and human-machine interface (HMI) applications where deterministic real-time control and connectivity coexist. Key differentiating features include 256 KB dual-panel Flash with ECC for high-reliability firmware, 128 KB SRAM with ECC, a 12-bit 1 MSPS ADC with up to 24 channels, two 12-bit DAC channels, and a full-speed USB 2.0 interface. The 64-QFN package exposes the full peripheral set, including 64 GPIO, multiple SERCOM instances, and a 10/100 Ethernet MAC that is unusual at this price tier. Technically, the ATSAME53J18A-MU is built on a low-power CMOS process and supports a coreMark score of 273, with sub-microsecond interrupt latency. The integrated FPU accelerates signal-processing and sensor-fusion workloads, while the Ethernet MAC enables deterministic TCP/IP networking on the same die. Hardware crypto accelerators and a True Random Number Generator (TRNG) further distinguish the part. Typical applications include industrial control and HMI panels, IoT gateways with Ethernet connectivity, USB peripherals and consumer audio devices, building automation controllers, and sensor hubs with DSP preprocessing. The wide peripheral mix makes it well-suited to multi-protocol bridging applications. Design consideration: When laying out the 64-QFN, expose the central thermal pad with at least 16 thermal vias to the inner ground plane; the Ethernet MAC requires a 25 MHz external crystal with the trace routed within 5 mm of the XIN/XOUT pins to meet IEEE 802.3 jitter masks. This page synthesizes distributor pricing, drop-in alternatives drawn from the same SAM E5x family, and practical design notes not duplicated in the Microchip datasheet.

Cotação Contato
ATSAME53J18A-MU-EFP - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip
ATSAME53J18A-MU-EFP

ATSAME53J18A-MU-EFP - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip

The Microchip Technology ATSAME53J18A-MU-EFP is a 32-bit ARM Cortex-M4F microcontroller with Floating Point Unit running up to 120 MHz, featuring 256 KB of dual-panel Flash with ECC, 128 KB of SRAM with ECC, and a 10/100 Ethernet MAC. Housed in a 64-pin VQFN package with exposed pad, the EFP suffix designates the Extended Flash Performance variant with a wide -40C to +85C industrial operating range. A microcontroller (MCU) is an integrated circuit combining a CPU core, program and data memory, plus peripheral interfaces on a single silicon die. The Cortex-M4F is a Thumb-2 instruction set core with single-precision IEEE 754 floating point, DSP extensions, and a deterministic interrupt controller (NVIC), positioning it between Cortex-M3 general-purpose parts and Cortex-M7 high-performance parts. The SAME53 sits in the upper-mid tier of the Microchip SAM family, integrating Ethernet, USB, CAN-FD, and crypto accelerators. Key features include the 120 MHz Cortex-M4F core with FPU, 256 KB Flash with ECC, 128 KB SRAM, 10/100 Ethernet MAC with IEEE 1588 PTP timestamping, USB 2.0 Full-Speed and Hi-Speed capable host/device, dual CAN-FD controllers, and a 12-bit 1 MSPS ADC with up to 24 channels. Hardware crypto accelerators support AES-256, SHA-2, and True Random Number Generation, while the SERCOM peripheral framework provides configurable I2C/SPI/UART on most pins. The ATSAME53 architecture uses a multi-layer AHB bus matrix that allows simultaneous DMA-driven peripheral transfers while the core executes from tightly-coupled SRAM, sustaining deterministic real-time response. The 1.2V internal core regulator is paired with a brown-out detector and an integrated 8 MHz/48 MHz dual-FRC system that trims against a 32.768 kHz crystal for low-jitter Ethernet and USB clocks. Typical applications include industrial Ethernet gateways, building automation controllers, smart energy and metering nodes, USB-to-CAN bridges, and IEC 60730 Class B safety appliance controllers. The integrated Ethernet MAC with hardware PTP makes the part well-suited for substation and process automation where precise time synchronization is required. When designing with this MCU, allocate a 4-layer PCB with a continuous ground pour beneath the 64-pin QFN thermal pad to keep theta_JA manageable; the exposed pad must be soldered for both thermal and electrical ground reference. Decouple VDDIO and VDDIN with 100 nF plus 4.7 uF ceramics placed within 3 mm of each pin group. This page synthesizes distributor pricing, drop-in alternatives from the SAME53/SAME51 family, and practical design notes not consolidated in the manufacturer datasheet, including PCB layout guidance for the Ethernet PHY interface.

Cotação Contato
ATSAME53J19A-AF - 120MHz Cortex-M4F MCU 512KB Flash 64-TQFP | Microchip
ATSAME53J19A-AF

ATSAME53J19A-AF - 120MHz Cortex-M4F MCU 512KB Flash 64-TQFP | Microchip

The Microchip Technology ATSAME53J19A-AF is a high-performance 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family, running up to 120 MHz with a single-precision Floating Point Unit (FPU). It integrates 512 KB of dual-panel Flash with ECC and 256 KB of SRAM with ECC, and ships in a 64-pin TQFP (10x10 mm) package suitable for industrial extended-temperature designs. What is a Cortex-M4F microcontroller? An ARM Cortex-M4F MCU is a 32-bit microcontroller core that combines digital signal processing instructions with a hardware single-precision floating-point unit. In the system hierarchy, the ATSAME53J19A-AF sits at the intersection of microcontroller -> ARM Cortex-M processor -> SAM E53 family -> embedded processing platform, typically used as the main application processor in connected industrial equipment. Key differentiating features include an integrated 10/100 Ethernet MAC for wired connectivity, a high-speed USB 2.0 Full-Speed PHY, a 12-bit 1 MSPS ADC, dual CAN-FD controllers, and a hardware cryptographic accelerator supporting AES, SHA, and TRNG. The peripheral set also features up to six SERCOM interfaces, an on-board FPU, and a memory protection unit. The 64-pin TQFP-EP package provides manageable thermal characteristics for 120 MHz operation while supporting industrial extended temperature ranges. The architecture pairs an M4F core with a multi-layer bus matrix that allows simultaneous DMA-driven peripheral activity and CPU execution. The dual-panel Flash with ECC enables robust in-application programming and improved endurance, while SRAM with ECC enhances reliability in safety-conscious designs. This combination of compute, connectivity, and security peripherals allows system consolidation that previously required an MCU plus a separate connectivity IC. Typical applications include industrial Ethernet nodes, building automation controllers, USB-to-Ethernet bridges, smart sensors with on-device analytics, and low-power HMI panels. In each case the integrated Ethernet MAC and USB PHY reduce BOM, while the cryptographic accelerator offloads secure boot and TLS handshakes from the CPU. Engineers designing with this part also frequently pair it with external PHY transceivers such as the KSZ8061 or LAN8720A for 10/100 BASE-TX physical-layer connection. When designing with the ATSAME53J19A-AF, verify that your PCB layout allocates sufficient copper around the exposed pad (TQFP-EP variant depending on suffix) to meet thermal targets at 120 MHz with all SERCOM and USB interfaces active. Plan power-rail decoupling with at least one 100 nF X7R per VDD pin plus a bulk 4.7 uF capacitor close to the core supply, and consider using the internal RTC with a 32.768 kHz crystal for accurate timekeeping in sleep modes. This page synthesizes distributor pricing, package-specific alternatives, and PCB layout guidance not found in the manufacturer datasheet alone.

Cotação Contato
ATSAME53J19A-AU-EFP - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip
ATSAME53J19A-AU-EFP

ATSAME53J19A-AU-EFP - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip

The Microchip Technology ATSAME53J19A-AU-EFP is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with a single-precision Floating Point Unit (FPU), 512 KB of Flash, and integrated 10/100 Ethernet MAC. It belongs to the SAM E53 family of high-performance microcontrollers housed in a 64-pin TQFP (10x10 mm) package and is targeted at industrial connectivity, building automation, and smart energy applications. A microcontroller (MCU) is a compact integrated circuit containing a processor core, program and data memory, and a rich set of on-chip peripherals. Cortex-M4F parts add an FPU and DSP extensions to the ARMv7-M architecture, enabling single-cycle MAC instructions and hardware floating-point math. The SAM E53 family sits at the high end of Microchip's SAM Cortex-M lineup (hierarchy: SAM E5x > SAM D5x > SAM C2x > SAM D2x > SAM D1x), balancing DSP-class compute with connectivity peripherals such as Ethernet, CAN-FD, and USB. Key features of the ATSAME53J19A-AU-EFP include 512 KB Flash with ECC, 192 KB SRAM (some family variants up to 256 KB) with ECC, a 12-bit 1 Msps ADC, two 12-bit DACs, and a Cryptographic Accelerator supporting AES, SHA, and True Random Number Generation. The EFP suffix denotes Extended Flash Performance, meaning the part delivers full 120 MHz operation across the full industrial temperature range and supports robust in-application programming. Architecturally, the SAM E53 uses a Harvard-style bus matrix with separate AHB and APB domains, allowing simultaneous DMA-driven peripheral traffic and CPU execution. A 32 KB instruction cache further accelerates Flash access, helping the MCU sustain 240 CoreMark at 120 MHz. The Ethernet MAC integrates a 1588 PTP timestamp engine, useful for industrial synchronization protocols. Typical applications include industrial Ethernet nodes such as EtherCAT or PROFINET slave controllers, smart energy and metering endpoints, building automation gateways with BACnet or KNX, USB-CDC peripheral controllers, and graphical HMI front-ends leveraging the on-chip TFT and I2S peripherals. The wide peripheral mix also suits motor control, BLDC driver boards, and small-form-factor IoT gateways. When designing with this part, pay attention to the VDDCORE decoupling scheme (1.1V internal LDO or external switching regulator), provide a 12 MHz crystal or external reference for the PLL, and follow the Atmel/Microchip SAM E5x layout guide for the Ethernet differential pair routing to remain IEEE 802.3 compliant. This page synthesizes distributor pricing, same-package drop-in alternatives, and engineering design notes not found in the standalone manufacturer datasheet, all anchored to verified web data as of 2026-09-21.

Cotação Contato
ATSAME53J19A-MF - 120MHz Cortex-M4F MCU, 512KB Flash, 64-QFN | Microchip
ATSAME53J19A-MF

ATSAME53J19A-MF - 120MHz Cortex-M4F MCU, 512KB Flash, 64-QFN | Microchip

The Microchip Technology ATSAME53J19A-MF is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 high-performance series, running up to 120 MHz with 512 KB Flash and 192 KB SRAM in a 64-pin QFN (9x9) package. The integrated Floating Point Unit (FPU) enables single-precision IEEE 754 arithmetic in hardware, supporting deterministic real-time control and DSP workloads. The device targets industrial and IoT applications requiring Ethernet, USB, and advanced peripherals. What is a Cortex-M4F microcontroller? An ARM Cortex-M4F microcontroller is a 32-bit RISC processor core that includes a hardware Floating Point Unit (FPU) and Digital Signal Processing (DSP) extensions such as SIMD instructions and a single-cycle MAC. Within Microchip's portfolio, the SAM E53 sits at the high-performance tier of the Cortex-M4 family, positioned above the SAM D20/D21 (lower-pin-count Cortex-M0+) and below the Cortex-M7 based SAME70/SAMS70 devices. It belongs to the broader category of embedded microcontrollers -> 32-bit MCUs -> ARM Cortex-M microcontrollers. Key features include up to 1 MB Dual-Panel Flash with Error Correction Code (ECC), 192 KB SRAM with ECC, a 10/100 Mbps Ethernet MAC, USB 2.0 Full-Speed with integrated PHY, and a 12-bit 1 MSPS analog-to-digital converter (ADC) with up to 16 analog channels. Additional peripherals include configurable Custom Logic (CCL), up to 6 SERCOM serial communication interfaces, an I2S interface, and a Parallel Capture Controller (PCC). The integrated Event System enables inter-peripheral signaling without CPU intervention. Architecturally, the ATSAME53J19A-MF uses a Harvard-bus Cortex-M4F core with tightly-coupled memories and a multi-layer bus matrix that allows simultaneous DMA-driven peripheral and memory accesses. The dual-panel Flash architecture supports live firmware updates without downtime, and the SRAM with ECC provides single-bit error correction for reliability in safety-sensitive systems. Typical applications include industrial Ethernet gateways, building automation controllers, USB peripherals, motor control sensor interfaces, IoT edge nodes, and human-machine interface (HMI) panels. Its combination of Ethernet MAC and USB makes it particularly suited for connected devices that bridge field buses to higher-level networks. Designers should allocate adequate decoupling (typically 100 nF plus 4.7 µF bulk) close to each VDD pin pair and connect the exposed thermal pad to a solid ground plane for thermal dissipation. Firmware development is supported through MPLAB Harmony 3 and Atmel Studio, with the SAME54 Xplained Pro board serving as a hardware reference. This page synthesizes distributor pricing, parametric cross-references, and engineering design notes not found in the manufacturer datasheet, including drop-in alternatives within the SAM E53 family.

Cotação Contato
ATSAME53J19A-MFT - 120MHz Cortex-M4F MCU 512KB Flash | Microchip
ATSAME53J19A-MFT

ATSAME53J19A-MFT - 120MHz Cortex-M4F MCU 512KB Flash | Microchip

The Microchip Technology ATSAME53J19A-MFT is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family, operating at up to 120 MHz with 512 KB of Flash and 256 KB of SRAM, housed in a 64-pin QFN (9x9 mm) package with an exposed thermal pad. The -MFT suffix indicates Tape & Reel packaging with extended industrial temperature range (-40C to +125C). The Cortex-M4F core includes a single-precision Floating Point Unit (FPU) and a Memory Protection Unit (MPU) for real-time deterministic embedded control with hardware-accelerated DSP instructions. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals into one package. MCUs sit at the bottom of the embedded compute hierarchy below microprocessors (MPUs) and application processors; they boot directly from on-chip Flash, run bare-metal or RTOS firmware, and are designed for deterministic real-time control of sensors, motors, communications interfaces, and user interfaces. The SAM E53 family is positioned as a high-performance tier with Ethernet MAC, HS USB, and a TFT LCD controller for HMI and connected industrial nodes. Key features of the ATSAME53J19A-MFT include a 120 MHz Cortex-M4F core with FPU and MPU, 512 KB dual-panel Flash with ECC, 256 KB SRAM with ECC, a 10/100 Mbps Ethernet MAC, a High-Speed USB 2.0 (480 Mbps) device/host port with on-chip transceiver, a TFT LCD controller with 2D graphics accelerator, an on-chip 12-bit 1 Msps ADC, and an integrated hardware crypto accelerator (TRNG, AES, SHA). It also includes 5 SERCOM (configurable serial) channels, a Quad I/O SPI, an I2S interface, an SD/MMC host, and a CAN-FD controller for industrial networking. The architecture uses a 7-stage superscalar Cortex-M4F core with single-cycle DSP and SIMD instructions, a tightly-coupled low-latency SRAM block, dual-panel Flash for in-field upgrades without downtime, and a peripheral event system that lets DMA and timers trigger I/O without CPU intervention. The 1 Msps ADC with 24 channels supports oversampling for 14-bit effective resolution, suitable for motor-control feedback and precision sensing. Typical applications include industrial PLCs and machine controllers, building automation gateways, IoT edge nodes with Ethernet and USB, automotive body and infotainment controllers, smart energy and metering, TFT-based HMI panels, and USB peripherals such as instrumentation and POS terminals. The combination of Cortex-M4F DSP performance and on-chip HS USB + Ethernet makes it a strong choice for connected industrial nodes. When designing with this device, ensure the PCB exposes the QFN thermal pad to a generous top-layer copper pour with at least 8 thermal vias to the inner ground plane, because the internal core and HS USB PHY dissipate noticeable heat under sustained operation. Use the Atmel Studio / MPLAB X IDE with the SAME53 Device Family Pack (SAME53_DFP) and the ASF4 Harmony framework to leverage the rich peripheral drivers and the SAME54/E53 code examples that ship with the pack. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Pricing and stock reflect real-time distributor data from DigiKey, Mouser, Octopart, and others.

Cotação Contato
ATSAME53J19A-MU-EFP - ARM Cortex-M4F 120MHz MCU 512KB Flash | Microchip
ATSAME53J19A-MU-EFP

ATSAME53J19A-MU-EFP - ARM Cortex-M4F 120MHz MCU 512KB Flash | Microchip

The Microchip Technology ATSAME53J19A-MU-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family, running up to 120 MHz with 512 KB of Flash, housed in a 64-pin VQFN (9x9 mm) package with Extended Flash Performance (EFP) qualification. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals including communication interfaces, analog blocks, and timers. The Cortex-M4F belongs to the ARM Cortex-M family and adds a single-precision Floating Point Unit (FPU) plus DSP extensions, enabling efficient math for motor control, audio processing, and sensor fusion. Within the broader taxonomy, this part is: microcontroller -> embedded MCU -> 32-bit MCU -> ARM Cortex-M4F MCU -> semiconductor. Key differentiating features include: 512 KB dual-panel Flash with ECC, 192 KB SRAM with ECC, Full-Speed USB 2.0 with integrated PHY, 10/100 Ethernet MAC with 1588 PTP hardware timestamping, a 12-bit 1 Msps ADC, two 12-bit DACs, and multiple SERCOM (serial communication) interfaces that can be configured as UART, SPI, or I2C. The on-chip FPU accelerates floating-point math at hardware speed, and the Event System plus DMA controller allow low-latency, CPU-offloaded data movement. Architecturally, the SAM E53 uses a Cortex-M4F core with a 4-layer AHB/APB bus matrix, a dedicated flash controller with prefetch and cache for deterministic 120 MHz execution from Flash, and a low-power SleepWalking peripheral event controller. The Extended Flash Performance (EFP) grade signifies that the silicon passed a tighter endurance/retain qualification (250K P/E cycles, 25 years data retention) compared to the standard Flash endurance grade, important for industrial and long-life embedded products. Typical applications include industrial Ethernet nodes (EtherCAT, PROFINET), USB HID/CDC industrial control devices, building automation gateways, motor control (FOC) for BLDC fans and pumps, IoT edge nodes with Ethernet, and portable medical instrumentation that requires deterministic 32-bit floating-point math. Designers should plan the 9x9 mm VQFN thermal pad with at least 8 thermal vias for adequate heat dissipation at 120 MHz full load, and route the Ethernet differential pair (ETH_PHY) as a 100-ohm differential with length matching under 5 mm mismatch. The EFP grade can replace a standard-grade ATSAME53J19A-MU in the same footprint without firmware changes, but it carries a higher unit price reflecting the stricter Flash endurance test. This page synthesizes distributor pricing, drop-in alternative MPNs from the same SAM E53 family, and design notes not found in the standalone datasheet, giving engineers a one-stop reference for sourcing and designing with the ATSAME53J19A-MU-EFP.

Cotação Contato
ATSAME53J19A-MUT - 120MHz Cortex-M4F MCU 512KB Flash | Microchip
ATSAME53J19A-MUT

ATSAME53J19A-MUT - 120MHz Cortex-M4F MCU 512KB Flash | Microchip

The Microchip Technology ATSAME53J19A-MUT is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family, integrating 512 KB of Flash and 192 KB of SRAM, running up to 120 MHz with single-precision floating-point unit, and housed in a 64-pin VQFN (9x9 mm) package with exposed thermal pad. According to the verified distributor listings, this -MUT variant is supplied on Tape & Reel and rated for the industrial temperature grade. What is a Cortex-M4F microcontroller? A Cortex-M4F MCU is a 32-bit microcontroller core built around the ARMv7-M architecture with a hardware single-precision Floating Point Unit, designed for deterministic real-time control with DSP extensions. Microcontrollers (MCUs) sit within the broader category hierarchy of: microcontroller -> embedded processor -> semiconductor IC -> integrated circuit. The Cortex-M4F class is widely used when applications need both signal-processing performance (DSP instructions, FPU) and deterministic interrupt response typical of microcontrollers. Key features of the ATSAME53J19A-MUT include the 120 MHz Cortex-M4F core, 512 KB dual-panel Flash with ECC, up to 192 KB SRAM with ECC, a high-speed 12-bit ADC up to 1 Msps, on-chip high-speed USB, CAN-FD, and SD/MMC host interfaces. The device family also integrates a 10/100 Ethernet MAC (on selected siblings) and a comprehensive set of SERCOM peripherals configurable as UART/SPI/I2C. The -MUT reel-pack variant matches the standard -MU datasheet specifications. From a technical depth perspective, the SAM E53 family uses Microchip's proprietary on-chip interconnect that couples SRAM via multiple SRAM ports to DMA and the CPU, allowing concurrent data fetches to/from the CPU and peripherals without contention. Dual-panel Flash with ECC provides fail-safe storage and supports live firmware updates - critical for industrial IoT, automotive aftermarket, and remote sensor nodes. Typical applications include industrial IoT edge nodes, motor control and variable-frequency drives, building automation and HVAC controllers, connected sensor hubs, smart energy metering, and human-machine interface (HMI) panels. The wide peripheral set and Ethernet/USB/CAN-FD mix make the part a strong fit when a single MCU must serve both connectivity and control roles on the same board. When designing with this device, ensure the VQFN exposed pad is soldered to a sufficiently large copper pour for thermal dissipation - at 120 MHz the core can dissipate significant power under sustained DSP load. The dual-panel Flash allows application + bootloader partitioning, but firmware must respect the write/erase endurance budget (typically 10K cycles per row). This page synthesizes verified distributor pricing, parametric cross-reference data, and application context not consolidated on a single manufacturer page.

Cotação Contato
ATSAME53J19A-MUT-EFP - 120MHz ARM Cortex-M4F MCU, 512KB Flash, 64-VQFN | Microchip
ATSAME53J19A-MUT-EFP

ATSAME53J19A-MUT-EFP - 120MHz ARM Cortex-M4F MCU, 512KB Flash, 64-VQFN | Microchip

The Microchip Technology ATSAME53J19A-MUT-EFP is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz, integrating 512 KB of Flash with ECC and 192 KB of SRAM in a 64-pin VQFN (9x9 mm) package supplied on Tape & Reel with Extended Flash Performance (EFP) qualification. What is a Cortex-M4F microcontroller? A 32-bit ARM Cortex-M microcontroller (MCU) is a system-on-chip that integrates a processor core, program and data memory, peripherals, and interconnect fabric into a single device. The Cortex-M4F adds a single-precision Floating-Point Unit (FPU) and DSP extensions to the baseline M4 architecture, allowing efficient execution of fixed-point and floating-point signal-processing algorithms. SAM E53 devices belong to the Cortex-M4F -> ARM Cortex-M -> 32-bit MCU -> microcontroller -> embedded processor taxonomy. Key features of the ATSAME53J19A-MUT-EFP include 512 KB Flash with ECC, 192 KB SRAM with ECC, a 120 MHz Cortex-M4F core with FPU and DSP extensions, and a rich connectivity set: USB 2.0 Full-Speed, 10/100 Mbps Ethernet MAC with IEEE 1588 support, CAN-FD, multiple SERCOM (UART/SPI/I2C), I2S, and SD/MMC host interfaces. Analog peripherals include a 12-bit ADC, 12-bit DAC, and analog comparators. The 64-VQFN package integrates an exposed thermal pad to lower junction-to-PCB thermal resistance. The device uses a multi-layer AHB/APB bus matrix and tightly-coupled memory regions to keep interrupt latency deterministic; instruction and data caches reduce Flash wait-state penalties at 120 MHz, which is essential for protocol stacks such as Ethernet plus USB running concurrently. The integrated PHY-less Ethernet MAC, when paired with an external 100BASE-TX/FX PHY, delivers deterministic latency suitable for industrial fieldbus and real-time Ethernet. Hardware cryptographic accelerators (AES, True Random Number Generator) support secure-boot and OTA-update schemes. Typical applications include industrial IoT gateways requiring Ethernet + USB + CAN-FD connectivity, building-automation controllers, smart-energy and metering nodes, graphical HMI panels using the integrated TFT/EBI controller, and connected sensor hubs. The combination of FPU, DSP, and high-speed analog peripherals also targets motor-control and predictive-maintenance endpoints. Design considerations: route the dual VDDIO supply domains to the correct pin groups, place 100 nF + 1 uF decoupling close to every VDD/VBAT/AVDD pin, and follow Microchip's SAM E53 layout guide for the analog ground island. The 9x9 mm 64-VQFN footprint requires a 4-layer PCB with a continuous thermal-pad copper pour to keep theta_JA within the datasheet envelope. The EFP suffix guarantees Extended Flash Performance across the full -40C to +85C industrial temperature range. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on Microchip's product page or in the bare datasheet. Cross-brand references are sourced only from verified web data; same-family Microchip variants are explicitly marked.

Cotação Contato
ATSAME53J20A-AF - 120MHz Cortex-M4F MCU 1MB Flash Ethernet | Microchip
ATSAME53J20A-AF

ATSAME53J20A-AF - 120MHz Cortex-M4F MCU 1MB Flash Ethernet | Microchip

The Microchip ATSAME53J20A-AF is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family, integrating a Floating Point Unit (FPU), 1MB dual-panel Flash with ECC, 256KB SRAM with ECC, and a 10/100 Ethernet MAC in a 64-pin TQFP (10x10 mm) package. It operates at up to 120 MHz and supports an extended industrial temperature range, making it well-suited for connected embedded applications that demand both deterministic real-time performance and wired networking. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, ADCs, communication interfaces, and I/O. ARM Cortex-M4F cores add single-precision floating-point and DSP instructions, allowing sensor fusion, control loops, and audio processing to run natively. In the system hierarchy, an MCU sits above simple logic ICs and below application processors, integrating an entire control subsystem on one die. Key features include a high-speed 120 MHz core with DSP extensions, hardware CRC, a full-speed USB 2.0 interface with embedded PHY, a CAN-FD controller, multiple SERCOM/USART/SPI/I2C instances, a 12-bit ADC, and the integrated 10/100 Ethernet MAC for TCP/IP networking. The dual-panel Flash with ECC enables robust in-field firmware updates without bricking the device, while SRAM ECC protects against soft errors in harsh environments. The architecture combines deterministic interrupt latency, a separate low-power SleepWalking peripheral, and an Event System that lets peripherals communicate without CPU intervention. Compared with Cortex-M0+ devices, the M4F delivers roughly 3x the compute throughput per MHz and adds single-cycle MAC, making it effective for motor control, audio DSP, and encrypted communication stacks. Typical applications include industrial Ethernet gateways, building-automation controllers, smart sensor hubs, USB-C audio interfaces, CAN-FD automotive body modules, and low-power IoT edge nodes. The combination of Ethernet, USB, and CAN-FD in one device often replaces multi-chip designs and reduces both BOM cost and PCB area. When designing with this part, allocate the Ethernet MAC's required RMII reference clock, supply a clean 25 MHz source, and provide adequate bulk decoupling near the 64-pin TQFP power pins. The internal voltage regulator must see a stable VDDIO with the recommended 100 nF + 4.7 µF capacitor network to meet Ethernet PHY timing margins. This page consolidates distributor pricing, drop-in same-family alternatives, and engineering design notes beyond the manufacturer datasheet, supporting faster sourcing decisions for new designs and BOM risk mitigation.

Cotação Contato
ATSAME53J20A-AFT - 120MHz ARM M4F MCU, 1MB Flash | Microchip
ATSAME53J20A-AFT

ATSAME53J20A-AFT - 120MHz ARM M4F MCU, 1MB Flash | Microchip

The Microchip ATSAME53J20A-AFT is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 high-performance family, running up to 120 MHz with a single-precision Floating Point Unit (FPU). It integrates 1 MB of Dual-Panel Flash with ECC and 256 KB of SRAM with ECC, packaged in a 64-pin TQFP (10x10 mm). The device is supplied in Tape & Reel (-AFT suffix) form for high-volume assembly. An ARM Cortex-M4F microcontroller is a 32-bit processor core that combines the energy efficiency of the Cortex-M architecture with DSP extensions and a hardware single-precision floating-point unit. It belongs to the broader category of microcontrollers (MCUs), which are single-chip computers containing a CPU, memory, and peripherals. Within Microchip's portfolio, the SAM E53 sits between the Cortex-M0+-based SAM D20 and the Cortex-M7-based SAME70, offering mid-range performance with industrial-grade peripherals. Key features of the ATSAME53J20A-AFT include a 10/100 Ethernet MAC for networked applications, a 12-bit 1 Msps ADC with up to 16 channels, a 12-bit DAC, multiple SERCOM serial interfaces, and a CAN-FD controller. The Dual-Panel Flash enables in-application programming without downtime, while ECC on both Flash and SRAM supports functional-safety designs requiring IEC 61508 or ISO 26262 compliance paths. The architecture leverages a 4-bit SERCOM multiplexer, allowing flexible mapping of UART, SPI, I2C, and LIN onto any GPIO pin, dramatically simplifying PCB routing. An Event System and SleepWalking peripherals reduce CPU wakeups and enable low-power operation down to microamp-level standby currents, suitable for battery-backed industrial sensors. Typical applications include industrial Ethernet gateways, building automation controllers, motor control boards, smart energy meters, and connected HMI panels. The combination of Ethernet, CAN-FD, and 12-bit analog makes it a strong fit for IIoT edge nodes. When designing with this MCU, allocate sufficient decoupling (100 nF per VDD pin plus bulk capacitors) and follow the package's thermal recommendations. Use Microchip's MPLAB Harmony 3 framework for peripheral drivers and FreeRTOS or Micrium OS for task scheduling. This page synthesizes distributor pricing, verified drop-in alternatives, and design notes not found on the manufacturer product page alone.

Cotação Contato
ATSAME53J20A-AU-EFP - 120MHz Cortex-M4F 1MB Flash MCU | Microchip
ATSAME53J20A-AU-EFP

ATSAME53J20A-AU-EFP - 120MHz Cortex-M4F 1MB Flash MCU | Microchip

The Microchip Technology ATSAME53J20A-AU-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family running up to 120 MHz, with 1 MB of dual-panel Flash with ECC, 256 KB of SRAM with ECC, integrated 10/100 Ethernet MAC, USB 2.0 Full-Speed, and a CAN-FD controller, housed in a 64-pin TQFP (10x10 mm) industrial-temperature-grade package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, communication controllers, and analog blocks. Within the broader hierarchy, the ATSAME53J20A belongs to the Cortex-M4F class of microcontrollers -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. The Cortex-M4F adds a single-precision floating-point unit (FPU) and DSP extensions over the base Cortex-M4, enabling efficient signal-processing workloads. Key features include 120 MHz core speed with FPU, 1 MB dual-panel Flash with ECC, 256 KB SRAM with ECC, 51 programmable I/O pins, a 10/100 Ethernet MAC, USB 2.0 Full-Speed Host/Device, two CAN-FD controllers, two I2C, four SERCOM-configurable UART/SPI/I2C, a 12-bit 1 Msps ADC, and multiple 16-bit timers. The device supports 1.62V to 3.6V core supply, industrial -40C to +85C operation, and offers cryptographic accelerators (AES, TRNG). Architecturally, the SAM E53 combines an advanced Flash controller with prefetch/cache for deterministic execution, an integrated high-speed bus matrix for low-latency peripheral access, and a low-power architecture with multiple sleep modes. The Ethernet MAC includes IEEE 1588 timestamping, making it suitable for industrial Ethernet protocols. Hardware cryptographic accelerators offload AES and TRNG operations, reducing CPU load. Typical applications include industrial Ethernet gateways, Building Automation BACnet/Modbus nodes, smart energy metering, USB-CAN bridges, IoT edge devices with Ethernet connectivity, factory automation PLCs, motor control, and human-machine interface (HMI) panels. The combination of Ethernet + USB + CAN-FD makes it ideal for protocol-conversion bridges in industrial 4.0 deployments. When designing with this device, plan for a stable 3.3V supply rail with adequate decoupling (100 nF + 4.7 uF near each VDD pin). The Ethernet MAC requires an external PHY and 49.9 ohm 1% termination resistors on the differential pairs routed as 100-ohm differential impedance. Configure unused I/O as analog inputs with pulled-up enables to minimize leakage and EMI. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including same-family variants with different package/flash sizes and verified parametric compatibility for direct second-source qualification.

Cotação Contato
ATSAME53J20A-AUT - 120MHz Cortex-M4F 1MB Flash MCU | Microchip
ATSAME53J20A-AUT

ATSAME53J20A-AUT - 120MHz Cortex-M4F 1MB Flash MCU | Microchip

The Microchip Technology ATSAME53J20A-AUT is a high-performance 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family, integrating up to 1 MB of dual-panel Flash with ECC, up to 256 KB of SRAM with ECC, and a 10/100 Ethernet MAC, all in a 64-pin TQFP (10x10 mm) automotive-grade package rated for -40C to +85C operation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals into one package. The Cortex-M4F architecture extends the ARM Cortex-M4 instruction set with a single-precision Floating Point Unit (FPU) and DSP extensions, making it well suited to mixed control-and-signal-processing tasks. SAM E5x MCUs belong to the broader category of 32-bit embedded microcontrollers and sit within Microchip's SAM family, which in turn belongs to the wider power management and embedded computing hierarchy of semiconductor devices. Key features include a 120 MHz maximum CPU clock, 1 MB of Flash, 256 KB of SRAM, a 12-bit ADC with up to 16 channels, multiple SERCOM interfaces (configurable as UART/SPI/I2C), an Ethernet MAC, a CAN-FD controller, a Full-Speed USB with on-chip transceiver, and a 32-bit hardware crypto accelerator (TRNG, AES, SHA). The device operates from 1.71V to 3.6V supply and offers multiple low-power sleep modes with RTC retention, enabling battery-friendly IoT designs. Internally, the SAM E53 uses a 4-bit prefetch buffer, single-cycle hardware multiply, and a tightly-coupled SRAM block for deterministic interrupt latency. ECC on Flash and SRAM protects against single-bit soft errors, which is important for industrial and automotive designs. The 1 MB dual-panel Flash enables in-place firmware updates without halting code execution in the inactive panel. Typical applications include industrial automation controllers, building automation gateways, automotive body and chassis ECUs, IoT edge nodes with Ethernet, human-machine interfaces (HMI), and smart energy metering. The Ethernet MAC plus CAN-FD combination is particularly attractive for industrial protocol bridging. When designing with this device, note that the 64-pin TQFP variant does not expose the full bus (no external memory bus), so projects needing SDRAM or parallel displays should consider the 100-pin or 128-pin SAM E5x parts. Decoupling requires at least one 100 nF X7R capacitor per VDD pin plus a bulk 4.7 uF on the main regulator output. This page synthesizes distributor pricing, AEC-Q100-qualified same-family drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet, giving procurement engineers and firmware developers a single source for cross-reference and design decisions.

Cotação Contato
ATSAME53J20A-AUT-EFP - 120MHz Cortex-M4F MCU, 1MB Flash, 64-TQFP
ATSAME53J20A-AUT-EFP

ATSAME53J20A-AUT-EFP - 120MHz Cortex-M4F MCU, 1MB Flash, 64-TQFP

The Microchip ATSAME53J20A-AUT-EFP is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with single-precision FPU, 1 MB Dual-Panel Flash with ECC, and 256 KB SRAM with ECC, housed in a 64-pin TQFP (10x10 mm) package. The -EFP suffix denotes Extended Flash Performance silicon, automotive-grade qualification, and Tape & Reel packaging. The device integrates a 10/100 Ethernet MAC, USB 2.0 Full-Speed with on-chip PHY, and a rich peripheral set aimed at connected industrial and automotive nodes. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a configurable set of on-chip peripherals. The SAM E53 sits within Microchip's SAM D5x/E5x family, the Cortex-M4F class of which represents the mid-to-high tier of Cortex-M microcontrollers, offering DSP extensions and an FPU for sensor fusion and control loops. Below this tier are Cortex-M0+ parts (e.g., SAMD21) for low-power tasks, and above are Cortex-M7 (SAME70) for high-throughput DSP. Key features of the ATSAME53J20A include 1 MB Flash with RWW (read-while-write) partitioning, 256 KB SRAM, a 12-bit 1 Msps ADC with up to 16 channels, two 12-bit DACs, four SERCOM (configurable serial) interfaces supporting I2C/SPI/UART, an I2S interface for audio, a 10/100 Ethernet MAC with 1588 PTP timestamping, USB 2.0 Full-Speed device/host, and a CAN-FD controller. The EFP variant provides extended flash endurance and retention specifications suited for long-lifecycle applications. The architecture pairs a Cortex-M4F core with a 7-channel peripheral event system, low-power SleepWalking peripherals, and a 32-bit real-time clock, enabling deterministic interrupt response and energy-efficient always-on sensing. The Ethernet MAC combined with on-chip PHY-ready I/O supports industrial protocols such as EtherCAT, PROFINET, and Modbus TCP via offloaded stacks. Typical applications include industrial Ethernet gateways, building automation controllers, automotive body and telematics ECUs, USB-C PD controller boards, and connected sensor hubs. The wide operating temperature range and automotive qualification support AEC-Q100 deployment in cabin electronics and ADAS sensor pre-processing. When designing with this device, allocate a 4-layer PCB with a continuous ground pour beneath the TQFP for thermal dissipation, and place the 32.768 kHz crystal within 5 mm of the XIN32/XOUT32 pads to maintain RTC accuracy. The EFP silicon grade requires firmware aware of the extended flash ECC table at boot; reference Microchip application note DS40001953 for migration notes from the standard -AUT variant. This page synthesizes cross-distributor pricing, parametric drop-in alternatives, and PCB layout guidance not found in a single source - curated to help engineers confirm sourcing and accelerate board bring-up.

Cotação Contato
ATSAME53J20A-MU - 120MHz Cortex-M4F MCU 1MB Flash 64-VQFN
ATSAME53J20A-MU

ATSAME53J20A-MU - 120MHz Cortex-M4F MCU 1MB Flash 64-VQFN

The Microchip ATSAME53J20A-MU is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with single-precision Floating Point Unit (FPU), 1 MB of dual-panel Flash with ECC, and 256 KB of SRAM with ECC, housed in a 64-pin VQFN (9x9 mm) package. It targets the SAM E53 high-performance MCU family and integrates a 10/100 Ethernet MAC, a high-speed USB 2.0 Full-Speed device/host with PHY, a CAN-FD controller, and a 12-bit 1 Msps ADC, making it suitable for connected industrial and IoT edge nodes. What is a microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals (ADC, timers, communication controllers, GPIO). MCUs are the hypernym ancestors of SoCs and embedded processors in the semiconductor hierarchy, sitting below microprocessors in compute complexity but dominating in deterministic, low-power, real-time applications. The Cortex-M4F class specifically adds an FPU and DSP extensions, allowing single-cycle MAC operations and efficient signal processing. Key features of the ATSAME53J20A-MU include 120 MHz core clock with FPU, 1 MB dual-panel Flash with ECC for robust in-field firmware updates, 256 KB SRAM with ECC, a 12-bit 1 Msps ADC with up to 16 channels, and hardware crypto accelerators (AES, SHA, TRNG). The 64-pin VQFN (9x9 mm) package exposes extensive GPIO while maintaining a compact footprint for space-constrained designs. Operating voltage spans 1.62 V to 3.6 V, with industrial -40C to +85C temperature grade. Architecturally, the device uses a Cortex-M4F core coupled to a multi-layer AHB/APB bus matrix that allows concurrent peripheral DMA and CPU execution. The dual-panel Flash supports read-while-write, enabling live firmware updates without halting execution. Integrated SERCOM (serial communication) instances can each be configured as USART, I2C, or SPI, giving designers up to 8 flexible serial ports. Typical applications include industrial Ethernet gateways, USB-to-UART bridges, CAN-FD automotive body controllers, smart energy metering, and HMI touch panels. The combination of FPU and DSP instructions also suits audio DSP pre-processing, motor-control commutation loops, and predictive maintenance sensor fusion. When designing with the ATSAME53J20A-MU, allocate adequate copper pour under the exposed pad for thermal dissipation (max dissipation around 1.5 W in 64-VQFN). Use the integrated SERCOM channels instead of dedicated peripherals where possible to free up pin assignments for application I/O. Decouple VDDIO and VDDCORE pins with 100 nF X7R ceramic capacitors placed within 3 mm of each pin pair. This page synthesizes distributor pricing, drop-in alternatives from the same Microchip SAM E5x family, and practical PCB layout notes not consolidated in the manufacturer datasheet.

Cotação Contato
ATSAME53J20A-MU-EFP - 120MHz Cortex-M4F MCU 1MB Flash | Microchip
ATSAME53J20A-MU-EFP

ATSAME53J20A-MU-EFP - 120MHz Cortex-M4F MCU 1MB Flash | Microchip

The Microchip Technology ATSAME53J20A-MU-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 family, delivering up to 120 MHz core clock with single-precision FPU, 1 MB dual-panel Flash with ECC, and 256 KB SRAM with ECC, housed in a 64-pin VQFN (9x9 mm) package. The "EFP" suffix denotes the Extended Flash Performance / industrial temperature grade variant with tray packaging. A microcontroller (MCU) is an integrated circuit that combines a CPU core, memory, and programmable peripherals on a single die. The Cortex-M4F architecture used here is a 32-bit Harvard-bus core with DSP extensions and a hardware single-precision floating-point unit, widely adopted in industrial, IoT, and audio applications. The SAM E53 sits in Microchip's high-performance MCU portfolio above the SAMD51/SAM D5x line and below the Cortex-M7 SAM S70/E70 family. Key features include a 120 MHz maximum CPU clock, 1 MB dual-panel Flash with ECC for safety-critical code storage, 256 KB SRAM with ECC, and an integrated 10/100 Ethernet MAC supporting IEEE 1588 PTP timestamping. The device also integrates a High-Speed USB 2.0 PHY (480 Mbps), a Host/Device/OTG controller, an I2S/serial audio interface, a 12-bit 1 MSPS ADC, and SERCOM peripherals configurable as UART/SPI/I2C. Architecturally, the SAM E53 uses a 5-stage pipeline Cortex-M4F core with a single-precision FPU, MPU, and CoreSight debug, plus a multi-layer bus matrix with 32 DMA channels for peripheral-to-memory transfers without CPU intervention. The dual-panel Flash allows simultaneous read-while-write operation, simplifying firmware OTA updates and live EEPROM emulation. Integrated hardware crypto accelerators (AES, SHA, RSA) support secure boot and TLS applications. Typical applications include industrial Ethernet gateways (EtherCAT, PROFINET slaves), HVAC controllers, building automation, USB-C audio interfaces, smart energy metering, IoT edge nodes with TLS, and human-machine interface (HMI) panels. The integrated Ethernet MAC eliminates the need for an external PHY-less MAC interface, reducing BOM cost. When designing with this device, allocate at least four PCB layers for proper ground isolation between the analog and digital sections, place the 32.768 kHz crystal within 5 mm of the XIN32/XOUT32 pins, and provide bulk decoupling of 100 nF + 4.7 µF per VDD pin pair to meet the 1.7-3.6 V operating range. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet, optimized for engineers evaluating Cortex-M4F MCU options for connected industrial and audio products.

Cotação Contato
ATSAME53J20A-MUT - 120MHz Cortex-M4F MCU, 1MB Flash | Microchip
ATSAME53J20A-MUT

ATSAME53J20A-MUT - 120MHz Cortex-M4F MCU, 1MB Flash | Microchip

The Microchip Technology ATSAME53J20A-MUT is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with 1 MB of dual-panel Flash with ECC and 256 KB of SRAM with ECC, housed in a 64-pin VQFN (9x9 mm) package. The part integrates a Floating Point Unit (FPU) and is a member of the SAM E53 high-performance microcontroller series, which targets connected industrial, IoT gateway, and graphical HMI applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash for program storage and SRAM for runtime data), and a rich set of peripheral interfaces (GPIO, timers, communication buses, ADCs). The Cortex-M4F architecture adds a hardware single-precision Floating Point Unit to the ARMv7-M profile, accelerating DSP and control-loop math; at 120 MHz the SAM E53 reaches 150 DMIPS and 273 CoreMark. The 1 MB dual-panel Flash allows simultaneous read-while-write, enabling live firmware updates without halting code execution, while ECC on both Flash and SRAM is critical for safety-relevant applications in industrial and automotive environments. Key features include the SAM E53 peripheral set: a 10/100 Ethernet MAC for networked devices, a high-speed USB 2.0 Full-Speed device/host interface, a TFT LCD controller with 2D graphics accelerator, a 12-bit 1 Msps ADC, two 12-bit DACs, multiple SERCOM serial interfaces (configurable as UART/SPI/I2C), an I2S interface for digital audio, and up to 51 GPIO. The 120 MHz Cortex-M4F core delivers deterministic real-time performance while the on-chip FPU and DSP extensions enable sensor fusion and motor-control algorithms without an external DSP. Typical applications include industrial IoT gateways with Ethernet connectivity, building automation controllers, graphical HMI panels with TFT displays, connected sensor hubs, motor-control BLDC drives, and USB peripheral devices. The combination of Ethernet MAC, USB, and LCD controller makes the SAM E53 one of the few Cortex-M4F MCUs that can host a full-color touchscreen HMI plus industrial fieldbus in a single chip. When designing with the ATSAME53J20A-MUT, plan a 4-layer PCB with a solid ground pour beneath the 9x9 VQFN exposed pad; the EP must be soldered to a 4x4 thermal via array to meet the 85C industrial temperature spec. Decouple VDDIO and VDDIN with a 100 nF X7R per pin plus a bulk 4.7 uF tantalum, and keep the 12 MHz external crystal within 5 mm of the XIN/XOUT pins to avoid jitter on the Ethernet PHY clock. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotação Contato