BSS169H6327XTSA1 - 100V N-Ch Depletion MOSFET 170mA | Infineon
N.º da peça: BSS169H6327XTSA1 ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $0.42 | $0,42 |
| 10 | $0.38 | $3,80 |
| 100 | $0.31 | $31,00 |
| 500 | $0.24 | $120,00 |
| 1.000 | $0.19 | $190,00 |
| 3.000 | $0.15 | $450,00 |
BSS169H6327XTSA1 Visão geral
A depletion-mode MOSFET (also called a depletion-mode or normally-on FET) is a field-effect transistor that conducts at zero gate-source bias. Unlike standard enhancement-mode MOSFETs (such as the ubiquitous 2N7002 or BSS138), which require a positive VGS to turn on, depletion-mode devices are on by default and require a negative gate bias to switch off. This normally-on behavior places depletion-mode MOSFETs in the broader family of field-effect transistors within power semiconductors, sitting alongside JFETs, standard MOSFETs, and IGBTs in the device taxonomy. The hypernym chain runs depletion-mode MOSFET -> field-effect transistor -> transistor -> discrete semiconductor.
Key features of the BSS169 include the always-on characteristic that simplifies startup circuitry, a pinch-off voltage around -3.5 V that allows digital logic drive from a single supply, low leakage at full pinch-off, and a small SOT-23 footprint that fits in any 0402-class board space. The device's 100 V drain rating provides generous headroom for 24 V industrial rails and telecom supply protection circuits. Its depletion-mode nature makes it particularly valuable in power-supply startup, in-rush-current limiting, over-voltage protection, and off-line voltage reference circuits where a normally-on pass element is preferred.
Technically, the BSS169 uses a vertical DMOS structure that gives it a low RDS(on) when fully on and a sharp pinch-off curve for clean switching. Designers exploit the always-on channel to pre-bias downstream stages or build constant-current sources using the saturation characteristic. Compared to enhancement-mode alternatives, the BSS169 simplifies gate-drive networks but requires careful handling because it cannot be turned off by simply pulling the gate to ground.
Typical applications include power-supply startup assistance (where it acts as a soft-start bypass), in-rush current limiters at the input of hot-plug DC rails, over-voltage protection crowbars, off-line voltage references for SMPS controllers, normally-on level shifters, and constant-current source circuits. The wide VDS range also suits it to 48 V telecom and PoE protection.
When designing with the BSS169, plan the gate-bias network first because the device is on at VGS=0. A typical circuit uses a resistor divider or zener clamp to set a defined pinch-off state during normal operation. Confirm that downstream circuits tolerate the always-on condition during power-up, and ensure the gate-source zener clamp does not exceed the +/-20 V VGS absolute maximum.
This page synthesizes distributor pricing from DigiKey and Mouser, drop-in alternatives verified against the SOT-23 footprint, and practical depletion-mode design notes that go beyond the manufacturer's datasheet.
Alternativas drop-in para BSS169H6327XTSA1 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com BSS169H6327XTSA1 (mesmo formato e footprint) — diferindo em Package, Technology, Continuous Drain Current (ID), Power Dissipation (PD), Drain-Source Voltage (VDS).
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
BSS139H6327XTSA1
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
BSS169H6327XTSA2
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
BSS169 L6327
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
BSS83 H6327
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
BSS84 H6327
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
2N7002L
✅ Drop-In✓ Em estoque
$0.028 / unidade
Ver ficha técnica →BSS169H6327XTSA1 Classificações máximas e características elétricas
| FET Type | N-Channel Depletion Mode |
| Drain-to-Source Voltage (VDS) | 100 V |
| Continuous Drain Current (ID) | 170 mA (Ta) |
| Power Dissipation (PD) | 360 mW (Ta) |
| RDS(on) Maximum | 6 Ohm at VGS=0 V |
| Gate Threshold Voltage (VGS(th)) | Pinch-off approx. -3.5 V (typical) |
| Encapsulamento | PG-SOT23 (SOT-23-3) |
| Tipo de montagem | Surface Mount |
| Contagem de pinos | 3 |
| Nível MSL | 1 (per JEDEC J-STD-020) |
| Status RoHS | Compliant |
| Lead-Free | Yes |
| Technology | Depletion-mode vertical DMOS |
| Drain Current at 25C | 170 mA continuous |
Configuração de pinos do BSS169H6327XTSA1
| Pino 1 | Gate — Gate input; bias below pinch-off (~-3.5 V) to turn off |
| Pino 2 | Source — Source terminal; typically tied to circuit reference |
| Pino 3 | Drain — Drain terminal; up to 100 V VDS rating |
Área de Operação Segura (DC)
Aplicações típicas
BSS169H6327XTSA1 é adequado para 6 aplicaçãos: Power Supply Startup Bypass, In-Rush Current Limiter, Over-Voltage Protection Crowbar, Off-Line Voltage Reference, Constant-Current Source, Normally-On Level Shifter.
Power Supply Startup Bypass
The BSS169H6327XTSA1's depletion-mode characteristic makes it ideal as a startup bypass element in switching power supplies, where it conducts at VGS=0 to provide initial power to the SMPS controller before the auxiliary winding takes over. With 100 V VDS headroom and 170 mA continuous drain current, it comfortably handles the housekeeping current of small flyback or buck converters during the first switching cycles. The 6 Ohm RDS(on) at zero gate bias limits inrush, and once the controller is powered it can pull the gate below pinch-off to fully disable the BSS169 for normal operation.
Recomendado
In-Rush Current Limiter
The BSS169H6327XTSA1 serves as a self-biased in-rush current limiter at the input of hot-plug DC rails (24 V industrial, 48 V telecom). Its normally-on channel with 6 Ohm RDS(on) limits the initial charging current of bulk output capacitors when a card is plugged into a live backplane. As the rail stabilizes, the controller can bias the gate below pinch-off to fully open the channel for minimum loss. The 100 V VDS rating handles transient spikes common in 24 V industrial environments without avalanche breakdown.
Recomendado
Over-Voltage Protection Crowbar
In over-voltage protection circuits, the BSS169H6327XTSA1 acts as a normally-on pass element that conducts during normal operation and is biased off by a sense circuit when an over-voltage event is detected. When paired with a comparator that drives the gate to pinch-off at a defined threshold, the BSS169 disconnects the load within microseconds, protecting downstream components from sustained over-voltage stress. Its 100 V VDS rating makes it suitable for crowbar protection on 24 V and 48 V rails.
Recomendado
Off-Line Voltage Reference
The depletion-mode BSS169H6327XTSA1 is well-suited to off-line voltage-reference circuits where a small constant current must flow from a high-voltage rail to a precision shunt reference such as a TL431. The always-on channel with predictable RDS(on) provides a defined current path without requiring a powered controller to bias the gate. This simplifies offline auxiliary supplies and self-powered gate-drive bias networks in SMPS designs.
Recomendado
Constant-Current Source
The BSS169H6327XTSA1's depletion-mode characteristic and stable pinch-off curve enable simple two-terminal constant-current source circuits. By tying gate to source through a resistor and operating the device in saturation, a fixed drain current can be set over a wide range of drain voltages. This is useful for LED biasing, loop-powered transducer excitation, and biasing of precision analog stages where a stable current reference is required from a varying supply.
Recomendado
Normally-On Level Shifter
In industrial and telecom interfaces, the BSS169H6327XTSA1 functions as a normally-on level shifter between a high-voltage domain (24 V or 48 V) and a low-voltage logic or microcontroller domain. Because the device conducts at VGS=0, a simple resistor divider on the gate is enough to define the OFF state for the low-voltage side, eliminating the need for an additional gate-drive supply. The 100 V VDS rating tolerates transients on the high-voltage rail without failure.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para BSS169H6327XTSA1 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | BSS139H6327XTSA1 | BSS169H6327XTSA2 | BSS169 L6327 | BSS83 H6327 | 2N7002 |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | onsemi |
| Package | PG-SOT23 (SOT-23-3) | PG-SOT23 (SOT-23-3) - same | PG-SOT23 (SOT-23-3) - same | PG-SOT23 (SOT-23-3) - same | PG-SOT23 (SOT-23-3) - same | SOT-23-3 - same |
| FET Type | N-Channel Depletion Mode | N-Channel Depletion Mode | N-Channel Depletion Mode | N-Channel Depletion Mode | N-Channel Depletion Mode | N-Channel Enhancement Mode |
| VDS Max | 100 V | 60 V | 100 V | 100 V | 60 V | 60 V |
| Continuous Drain Current (Ta) | 170 mA | 240 mA | 170 mA | 170 mA | 100 mA | 115 mA |
| RDS(on) Max | 6 Ohm | 10 Ohm | 6 Ohm | 6 Ohm | 10 Ohm | 7.5 Ohm at VGS=10V |
| Power Dissipation | 360 mW | 360 mW | 360 mW | 360 mW | 360 mW | 200 mW |
| VGS(th) / Pinch-Off | -3.5 V (typical pinch-off) | -3.5 V (typical pinch-off) | -3.5 V (typical pinch-off) | -3.5 V (typical pinch-off) | -3.5 V (typical pinch-off) | +1 to +2.5 V (enhancement threshold) |
| Pinout (G/S/D) | 1-G, 2-S, 3-D | 1-G, 2-S, 3-D | 1-G, 2-S, 3-D | 1-G, 2-S, 3-D | 1-G, 2-S, 3-D | 1-G, 2-S, 3-D |
Principais diferenciais
- One of the few depletion-mode small-signal MOSFETs in volume production (vs 2N7002)
- Higher 100 V VDS rating than the BSS139 family (vs BSS139H6327XTSA1)
- Pin-compatible with standard SOT-23 small-signal MOSFETs (vs BSS83 H6327)
Notas de projeto
Because the BSS169H6327XTSA1 is depletion-mode and ON at VGS=0, it cannot be turned off by leaving the gate floating. Always provide a defined gate bias path - either a resistor to a known voltage or a zener clamp - to guarantee the desired OFF state during power-up and fault conditions. A floating gate can pick up noise and create undefined conduction states.
Estimated: at VDS=24 V, ID=170 mA continuous, RDS(on)=6 Ohm, the steady-state dissipation is approximately P = ID^2 * RDS(on) = 0.17^2 * 6 = 0.17 W, well within the 360 mW rating at 25C. However at 100 V VDS with the same current, designers must use pulsed operation or significantly derate for ambient temperature. The SOT-23 package has limited thermal headroom - check the SOA graph before operating at peak VDS and ID simultaneously.
Use a small copper pour under and around the drain pad to spread heat. Keep gate traces short and away from drain/source switching nodes to minimize parasitic coupling. For depletion-mode designs where the gate is biased through a high-impedance divider, add a 100 nF ceramic bypass between gate and source to shunt high-frequency noise that could otherwise modulate the channel.
In level-shifter or startup-bypass applications, the gate-source capacitance (Ciss) of the BSS169H6327XTSA1 can couple drain transients back to the gate through the Miller effect. A gate-source resistor of 100 kOhm to 1 MOhm helps discharge Ciss and stabilizes the OFF state during fast drain edges. Verify gate-bias network bandwidth against the fastest expected drain transition.
Informações de conformidade
RoHS and REACH compliance per Infineon product page. Not AEC-Q100 qualified; this part is intended for industrial and consumer applications, not automotive. Lead-free reflow-compatible per MSL1 rating.
