CLC5957MTDX/NOPB - 12-Bit 70MSPS Broadband ADC | TI/NSC
N.º da peça: CLC5957MTDX/NOPB ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $14.5 | $14,50 |
| 10 | $13.2 | $132,00 |
| 100 | $11.8 | $1.180,00 |
| 500 | $10.4 | $5.200,00 |
| 1.000 | $9.15 | $9.150,00 |
CLC5957MTDX/NOPB Visão geral
An ADC (analog-to-digital converter) is an integrated circuit that samples continuous analog signals and converts each sample into a discrete digital code, forming the essential bridge between the analog and digital signal domains. ADC devices sit within the broader semiconductor taxonomy as: data converter -> ADC -> pipelined ADC -> high-speed ADC. The 12-bit resolution and 70 MSPS sampling rate place the CLC5957 firmly in the mid-resolution, high-speed tier used for communications, instrumentation, and radar/IF signal chains.
Key features include 70 MSPS minimum sample rate, 12-bit resolution with no missing codes, differential input architecture for high common-mode rejection, and a pipelined converter core with 3-clock-cycle latency. The internal track-and-hold supports broadband analog inputs suitable for undersampling IF signals, and the parallel data interface simplifies FPGA or ASIC downstream connections. A separate DAV (data available) output simplifies timing into external logic.
The CLC5957 uses a pipelined architecture with internal bandgap reference and proprietary calibration, balancing high sampling rate with low power. Its internal reference design eliminates the need for an external reference IC, simplifying the BOM while keeping drift low enough for communications-grade applications. The pipelined 3.0-clock latency is well-documented in the National Semiconductor datasheet and is deterministic for synchronization in multi-channel systems.
Typical applications include IF-sampled digital receivers in cellular base stations, broadband communications test equipment, radar and signal-intelligence (SIGINT) front ends, medical imaging, and high-speed data acquisition. The combination of 12-bit resolution, 70 MSPS, and broadband input bandwidth makes it well-suited to undersampling IF architectures where a single ADC replaces multiple downconversion stages.
When designing with this part, pay careful attention to analog input coupling, the layout of the AVCC and DVCC planes, and the use of a low-jitter encode clock to preserve SNR. A 1% or tighter tolerance external reference is not required because the reference is internal, but a clean low-noise analog supply rail is essential to achieving published dynamic performance.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical PCB design notes that go beyond the manufacturer datasheet, so engineers can quickly decide whether the CLC5957MTDX/NOPB fits their IF-sampling or broadband acquisition design.
Alternativas drop-in para CLC5957MTDX/NOPB — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com CLC5957MTDX/NOPB (mesmo formato e footprint) — diferindo em Package / Case, Packaging, RoHS Status, Terminal Form.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
CLC5957MTD/NOPB
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
CLC5957MTDX
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADS8401IPFBT
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
CLC5957MTDX/NOPB Classificações máximas e características elétricas
| Number of Bits | 12 |
| Sampling Rate (Per Second) | 70 MSPS |
| Number of Inputs | 1 (differential) |
| Input Type | Differential |
| Data Interface | Parallel |
| Configuration | S/H-ADC |
| Architecture | Pipelined |
| Reference Type | Internal |
| Operating Supply Voltage (Analog) | 5 V |
| Operating Supply Voltage (Digital) | 5 V |
| Faixa de temperatura de operação | -40 C to +85 C |
| Pipeline Latency | 3.0 clock cycles |
| Encapsulamento / Caixa | 48-TFSOP (0.240", 6.10 mm width) |
| Tipo de montagem | Surface Mount |
| Packaging | Tape & Reel (TR) |
| Terminal Form | GULL WING |
| Temperature Grade | INDUSTRIAL |
| Status RoHS | Compliant (NOPB suffix indicates Pb-free) |
Guia de Configuração de Pinos do CLC5957MTDX/NOPB 48-tfsop (0.240", 6.10 mm width)
Configuração de pinos para CLC5957MTDX/NOPB (pacote 48-tfsop (0.240", 6.10 mm width)). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para CLC5957MTDX/NOPB.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
CLC5957MTDX/NOPB é adequado para 6 aplicaçãos: Cellular Base-Station IF-Sampling Receiver, Broadband Communications Test Equipment, Radar and SIGINT Front-End Digitizer, Medical Imaging Data Acquisition, High-Speed Data Acquisition Systems, Software-Defined Radio (SDR) IF Digitizer.
Cellular Base-Station IF-Sampling Receiver
The CLC5957MTDX/NOPB's 12-bit resolution and 70 MSPS sampling rate suit cellular base-station digital-IF architectures where a single ADC replaces multiple analog downconversion stages. Its broadband differential input stage supports undersampling of IF carriers in the 30-70 MHz range, preserving signal integrity for subsequent digital demodulation. The 3.0-clock pipeline latency is deterministic, allowing multi-channel coherent receiver synchronization. The internal reference and integrated track-and-hold minimize the external BOM, while separate AVDD/DVDD pins simplify PCB partitioning to maintain 70 dB+ SNR at the antenna interface.
Recomendado
Broadband Communications Test Equipment
For broadband communication testers and signal analyzers, the CLC5957MTDX/NOPB provides 12-bit acquisition at 70 MSPS with low-jitter ENCODE support, enabling accurate capture of multi-MHz waveforms. Its wide analog input bandwidth makes it ideal for digitizing QAM, OFDM, or wideband FM test signals without an external anti-alias filter bank. The parallel CMOS data output reduces latency to the FPGA, supporting real-time DSP for EVM and ACLR measurements. A low-jitter external encode clock (such as the AS1521) is recommended to preserve the converter's SNR at high input frequencies.
Recomendado
Radar and SIGINT Front-End Digitizer
The CLC5957MTDX/NOPB is well-suited to radar and signal-intelligence (SIGINT) front ends requiring sub-100 MSPS undersampling of intermediate frequencies. Its 12-bit dynamic range and broadband input allow direct digitization of pulsed RF signals at 30-50 MHz IF, eliminating an analog downconversion stage. The deterministic 3-clock latency eases time-of-arrival alignment in phased-array and direction-finding systems. Differential analog inputs reject common-mode noise from RF front-end mixers, while separate AVDD/DVDD supplies preserve 60-65 dB SFDR in the presence of digital switching noise.
Recomendado
Medical Imaging Data Acquisition
In medical imaging systems such as ultrasound beamformers and CT detector front ends, the CLC5957MTDX/NOPB provides 12-bit acquisition at 70 MSPS with a pipelined architecture suited to multi-channel parallel sampling. Its internal reference reduces per-channel calibration overhead, while the parallel interface simplifies FPGA-based digital beamforming. The 3-clock pipeline latency is well-defined for time-aligning arrays of ADCs across a beamformer aperture. Industrial temperature grade (-40 C to +85 C) supports portable diagnostic carts and bedside imaging platforms.
Recomendado
High-Speed Data Acquisition Systems
The CLC5957MTDX/NOPB fits general-purpose high-speed data acquisition cards in industrial test, vibration analysis, and laboratory instrumentation. Its 70 MSPS sample rate and 12-bit resolution support time-domain captures of transients, impulses, and broadband mechanical vibrations. The TSSOP-48 surface-mount package and parallel digital interface enable compact 4-layer PCB designs with FPGA downstream processing. The internal reference and integrated track-and-hold reduce analog front-end complexity, and the 5 V supply requirement simplifies integration with standard industrial power rails.
Recomendado
Software-Defined Radio (SDR) IF Digitizer
For software-defined radio platforms, the CLC5957MTDX/NOPB provides IF-sampling capability at 70 MSPS with 12-bit resolution, enabling direct digitization of 21-35 MHz intermediate frequencies from a single analog mixing stage. Its differential inputs reject common-mode noise from RF mixers and LNA stages, while the parallel CMOS data interface streams samples into FPGAs running open-source SDR frameworks. The deterministic 3-clock pipeline latency simplifies time-synchronization across multiple SDR channels. Industrial temperature grade and lead-free packaging support ruggedized deployable radio systems.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para CLC5957MTDX/NOPB — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | CLC5957MTD/NOPB | CLC5957MTDX | ADS8401IPFBT |
|---|---|---|---|---|
| Brand | Texas Instruments (NSC) | Texas Instruments (NSC) | Texas Instruments (NSC) | Texas Instruments |
| Package | 48-TSSOP (MTD) | 48-TSSOP (MTD) - same | 48-TSSOP (MTD) - same | 48-TQFP (PFB) - different package, same pin count |
| Resolution | 12 bits | 12 bits | 12 bits | 12 bits |
| Sampling Rate | 70 MSPS | 70 MSPS | 70 MSPS | 1 MSPS |
| Number of Inputs | 1 differential | 1 differential | 1 differential | 1 differential/pseudo |
| Architecture | Pipelined | Pipelined | Pipelined | SAR |
| Reference Type | Internal | Internal | Internal | External |
| Data Interface | Parallel | Parallel | Parallel | Parallel / serial |
| Pipeline Latency | 3.0 clock cycles | 3.0 clock cycles | 3.0 clock cycles | 0 (SAR, latency-free) |
| RoHS Compliance | Yes (NOPB) | Yes (NOPB) | No (leaded) | Yes |
Principais diferenciais
- Internal reference eliminates external reference IC (vs ADS8401IPFBT)
- 70 MSPS enables true IF sampling (vs ADS8401IPFBT)
- Deterministic 3-clock pipeline latency for multi-channel coherence (vs ADS8401IPFBT)
Notas de projeto
Use a 4-layer PCB with a dedicated ground plane under the CLC5957. Split AVDD and DVDD planes so digital return currents do not flow under the analog input pins; join them at a single point near the ADC. Place AVDD 5 V and DVDD 5 V decoupling capacitors (10 uF bulk + 0.1 uF + 0.01 uF ceramics) within 3 mm of each supply pin. Keep the ENCODE clock trace short and surrounded by ground to minimize jitter.
Drive the ENCODE clock from a low-jitter source such as the AS1521. Each picosecond of encode jitter degrades SNR by approximately 0.5 dB at 70 MSPS. For undersampling IF inputs, the analog input network should present a 50 ohm differential termination, and a balun (e.g. ADT1-1WT or equivalent) should be used if the upstream stage is single-ended. Keep analog input traces matched in length to within 1 mm to preserve the differential balance and maximize SFDR.
Do not exceed the AVDD/DVDD absolute maximum of 6.5 V. The internal reference cannot be overdriven - the REF pin is not designed to accept an external reference voltage. A separate DAV (data available) output is provided; do not use the falling clock edge of the parallel interface for synchronization, because the CLC5957's pipeline latency means the data is only valid relative to DAV. Re-examine timing at 70 MSPS in slow corners if your system runs at -40 C.
Informações de conformidade
NOPB suffix indicates lead-free (Pb-free) matte-tin finish per TI/NSC packaging convention. RoHS and REACH compliance assumed for NOPB parts; AEC-Q100 not applicable to commercial/industrial grade ADCs. Conflict minerals reporting compliant per TI corporate policy.
