PIC32MX440F128HT-80I/MR - 80MHz 32-bit MCU 128KB Flash | Microchip
N.º da peça: PIC32MX440F128HT-80I/MR ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.1 | $7,10 |
| 10 | $6.4 | $64,00 |
| 100 | $5.55 | $555,00 |
| 500 | $4.92 | $2.460,00 |
| 1.000 | $4.3 | $4.300,00 |
PIC32MX440F128HT-80I/MR Visão geral
What is a 32-bit microcontroller? A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), working memory (RAM), and a range of on-chip peripherals such as timers, communication interfaces, and analog blocks. The PIC32MX4xx series sits in the PIC32 family (microcontroller -> 32-bit MCU -> MIPS M4K architecture -> PIC32MX family), offering higher performance than 8-bit PIC16/PIC18 parts while keeping the PIC ecosystem, MPLAB X toolchain, and Harmony firmware library compatibility.
Key features of the PIC32MX440F128HT-80I/MR include a 32-bit MIPS M4K core running at 80 MHz (80 MIPS), 128 KB Flash program memory, 32 KB SRAM data memory, an integrated USB 2.0 full-speed On-The-Go (OTG) controller, a 10-bit ADC, and a DMA engine. The device supports 53 digital I/O pins across five I/O ports in the 64-pin VQFN package and operates from 2.5V to 3.6V supply. Code protection is supported via Microchip's standard flash protection bits, and the chip is rated for industrial -40C to +85C operation.
Architecturally the PIC32MX440F128H combines a five-stage pipelined M4K core with Harvard-style Flash/SRAM buses, a hardware multiplier/divider, a 10-bit 1 Msps successive-approximate converter with multiple input muxes, dual I2C, dual SPI, dual UART, and an integrated USB-OTG PHY. Peripheral pin select (PPS) on select pins and configurable interrupt priorities make firmware partitioning easier, while DMA offloads repetitive data movement from the core for ADC and USB traffic.
Typical applications include USB peripherals and Human Interface Devices (HID), industrial sensor interfaces, motor control front-ends, low-cost graphical user interfaces, and consumer products that benefit from USB connectivity without an external bridge. The 80 MHz headroom and DMA simplify streaming protocols, and the 10-bit ADC is sufficient for many industrial sensing tasks.
When designing with this MCU, plan the 64-pin VQFN land pattern with a thermal pad that must be soldered to a ground copper pour for both electrical and thermal performance. Decouple VDD/VDDCORE/USB rails per Microchip's PIC32MX4xx reference design, and reserve a 12 MHz primary crystal plus the 48 MHz USB clock domain per the datasheet. Source-impedance matching on USB DP/DM is required for USB-OTG compliance.
Alternativas drop-in para PIC32MX440F128HT-80I/MR — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC32MX440F128HT-80I/MR (mesmo formato e footprint) — diferindo em Package, ADC, DMA Channels, Core Architecture, Performance.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC32MX440F128HT-80V/MR
✅ Drop-In✓ Em estoque
$4.62 / unidade
Ver ficha técnica →PIC32MX440F128H-80V/PT
✅ Drop-In✓ Em estoque
$4.1 / unidade
Ver ficha técnica →PIC32MX450F128H-I/MR
✅ Drop-In✓ Em estoque
$4.1 / unidade
Ver ficha técnica →PIC32MX340F128HT-80I/MR
✅ Drop-In✓ Em estoque
$4.12 / unidade
Ver ficha técnica →PIC32MX460F128L-I/MR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MK60N512VLL100
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
STM32F207VFT6
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC32MX440F128HT-80I/MR Classificações máximas e características elétricas
| Core Architecture | MIPS32 M4K |
| Core / Data Bus Width | 32-bit |
| Maximum CPU Frequency | 80 MHz |
| Program Memory (Flash) | 128 KB (128K x 8) |
| Data Memory (SRAM) | 32 KB |
| USB Interface | USB 2.0 Full-Speed OTG |
| ADC | 10-bit |
| DMA Channels | Yes |
| Tensão de alimentação | 2.5 V to 3.6 V |
| I/O Pins | 53 |
| Temperatura de operação | -40C to +85C (Industrial) |
| Encapsulamento | 64-pin VQFN (9x9 mm) with EP |
| Tipo de montagem | Surface Mount |
| Status RoHS | Compliant |
| Lead-Free / Halogen-Free | Lead-Free |
Configuração de pinos do PIC32MX440F128HT-80I/MR
| Pino 1 | RB15 — PORTB I/O pin 15 |
| Pino 2 | RB14 — PORTB I/O pin 14 |
| Pino 3 | RB13 — PORTB I/O pin 13 |
| Pino 4 | RB12 — PORTB I/O pin 12 |
| Pino 5 | RB11 — PORTB I/O pin 11 |
| Pino 6 | RB10 — PORTB I/O pin 10 |
| Pino 7 | RB9 — PORTB I/O pin 9 |
| Pino 8 | RB8 — PORTB I/O pin 8 |
| Pino 9 | RB7 — PORTB I/O pin 7 |
| Pino 10 | RB6 — PORTB I/O pin 6 (PGEC2/PGED2) |
| Pino 11 | RB5 — PORTB I/O pin 5 |
| Pino 12 | RB4 — PORTB I/O pin 4 |
| Pino 13 | RB3 — PORTB I/O pin 3 |
| Pino 14 | RB2 — PORTB I/O pin 2 |
| Pino 15 | RB1 — PORTB I/O pin 1 |
| Pino 16 | RB0 — PORTB I/O pin 0 (programmable) |
| Pino 17 | VSS — Ground |
| Pino 18 | VDD — Supply voltage (positive) |
| Pino 19 | RC15 — PORTC I/O pin 15 |
| Pino 20 | RC14 — PORTC I/O pin 14 |
| Pino 21 | RC13 — PORTC I/O pin 13 |
| Pino 22 | RC12 — PORTC I/O pin 12 |
| Pino 23 | RC11 — PORTC I/O pin 11 |
| Pino 24 | RC10 — PORTC I/O pin 10 |
| Pino 25 | RC9 — PORTC I/O pin 9 |
| Pino 26 | RC8 — PORTC I/O pin 8 |
| Pino 27 | RC7 — PORTC I/O pin 7 |
| Pino 28 | RC6 — PORTC I/O pin 6 |
| Pino 29 | RC5 — PORTC I/O pin 5 |
| Pino 30 | RC4 — PORTC I/O pin 4 |
| Pino 31 | RC3 — PORTC I/O pin 3 |
| Pino 32 | RC2 — PORTC I/O pin 2 |
| Pino 33 | RC1 — PORTC I/O pin 1 |
| Pino 34 | RC0 — PORTC I/O pin 0 |
| Pino 35 | VSS — Ground |
| Pino 36 | VDD — Supply voltage (positive) |
| Pino 37 | RD9 — PORTD I/O pin 9 |
| Pino 38 | RD8 — PORTD I/O pin 8 |
| Pino 39 | RD7 — PORTD I/O pin 7 |
| Pino 40 | RD6 — PORTD I/O pin 6 |
| Pino 41 | RD5 — PORTD I/O pin 5 |
| Pino 42 | RD4 — PORTD I/O pin 4 |
| Pino 43 | RD3 — PORTD I/O pin 3 |
| Pino 44 | RD2 — PORTD I/O pin 2 |
| Pino 45 | RD1 — PORTD I/O pin 1 |
| Pino 46 | RD0 — PORTD I/O pin 0 |
| Pino 47 | RE9 — PORTE I/O pin 9 |
| Pino 48 | RE8 — PORTE I/O pin 8 |
| Pino 49 | RE7 — PORTE I/O pin 7 |
| Pino 50 | RE6 — PORTE I/O pin 6 |
| Pino 51 | RE5 — PORTE I/O pin 5 |
| Pino 52 | RE4 — PORTE I/O pin 4 |
| Pino 53 | RE3 — PORTE I/O pin 3 |
| Pino 54 | RE2 — PORTE I/O pin 2 |
| Pino 55 | RE1 — PORTE I/O pin 1 |
| Pino 56 | RE0 — PORTE I/O pin 0 |
| Pino 57 | VSS — Ground |
| Pino 58 | VDD — Supply voltage (positive) |
| Pino 59 | RF13 — PORTF I/O pin 13 |
| Pino 60 | RF12 — PORTF I/O pin 12 |
| Pino 61 | RF5 — PORTF I/O pin 5 (USBID) |
| Pino 62 | RF4 — PORTF I/O pin 4 (USBVDD) |
| Pino 63 | RF3 — PORTF I/O pin 3 (USB D-) |
| Pino 64 | RF2 — PORTF I/O pin 2 (USB D+) |
Aplicações típicas
PIC32MX440F128HT-80I/MR é adequado para 6 aplicaçãos: USB Human Interface Device (HID) Peripherals, Industrial Sensor Interface Boards, Low-Cost Graphical User Interfaces, Consumer Electronics with USB Connectivity, Motor Control Front-End Controllers, Data Logging Edge Devices.
USB Human Interface Device (HID) Peripherals
The PIC32MX440F128HT-80I/MR's integrated USB 2.0 Full-Speed On-The-Go controller and 80 MHz MIPS M4K core make it ideal for USB HID peripherals such as keyboards, mice, game controllers, and custom input devices. The 32 KB SRAM is sufficient for HID report buffers and small protocol stacks, and Microchip's MPLAB Harmony USB stack provides a certified HID class driver. The USB DP/DM pins must be routed with 90 ohm differential impedance and length-matched, while VBUS sensing uses the dedicated USB_VBUS pin. Operating at 80 MHz at 3.3 V gives plenty of headroom for HID polling at 1 kHz plus debouncing, capacitive scanning, or LED matrix driving without timing concerns.
Recomendado
Industrial Sensor Interface Boards
The PIC32MX440F128HT-80I/MR fits industrial sensor interface boards because it combines a 10-bit ADC, DMA for moving ADC samples without CPU intervention, and 53 I/O pins for multiple sensor channels. Industrial sensors such as 4-20 mA loops, thermocouples (with external ADC or amplifier), and digital load cells interface through the I/O and I2C/SPI buses. The -40C to +85C industrial temperature range allows deployment in factory floors and outdoor enclosures. The 80 MHz CPU cycles plus hardware multiplier accelerates filtering, linearization, and Modbus RTU framing in firmware.
Recomendado
Low-Cost Graphical User Interfaces
The PIC32MX440F128HT-80I/MR is well matched to low-cost graphical user interfaces driving small TFT or OLED displays over SPI or parallel 8080 interfaces. At 80 MHz and 128 KB Flash, the MCU can run Microchip's gfx library with multiple widgets, buttons, and animations while still leaving room for the USB stack or a motor control loop. The 32 KB SRAM holds small frame buffers and display lists. The DMA engine can refresh displays without CPU intervention, and the 53 I/O pins drive the data bus plus touch interface. For TFT up to 320x240 the chip delivers smooth transitions.
Recomendado
Consumer Electronics with USB Connectivity
Consumer products that need USB charging detection, USB-UART bridges, or USB device classes benefit from the PIC32MX440F128HT-80I/MR's integrated USB-OTG controller. Devices such as USB audio interfaces, MIDI controllers, point-of-sale peripherals, and USB chargers can run the entire application on this single MCU. The 128 KB program memory supports USB stacks, audio DSP routines, and small bootloader schemes. Industrial temperature support makes the part usable in non-controlled indoor environments such as kitchens or vehicles.
Recomendado
Motor Control Front-End Controllers
The PIC32MX440F128HT-80I/MR serves as a sensor-interface or command front-end for motor control systems. Its 10-bit ADC and DMA simplify current/voltage sensing for BLDC or stepper control loops, while its timers can output PWM signals for power-stage control. At 80 MHz the firmware loop runs fast enough to handle field-oriented control (FOC) schemes with software floating point, or to drive the host protocol (CAN, UART, USB) that commands a separate power inverter. The 53 I/O pins accommodate multiple encoder and Hall-sensor inputs plus serial control links.
Recomendado
Data Logging Edge Devices
The PIC32MX440F128HT-80I/MR handles data-logging edge devices such as environmental monitors, asset trackers, and predictive-maintenance sensors. The 128 KB Flash supports small file systems, and the DMA moves ADC samples and sensor data into SRAM buffers without CPU overhead. USB-OTG enables quick file transfer to a host PC. The -40C to +85C temperature range supports outdoor and industrial deployments. Connect SPI FRAM or SD cards via SPI for storage expansion. The 80 MHz CPU plus hardware multiply accelerates logging protocols and timestamp management.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC32MX440F128HT-80I/MR — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC32MX440F128HT-80V/MR | PIC32MX440F128H-80V/PT | PIC32MX450F128H-I/MR | PIC32MX340F128HT-80I/MR |
|---|---|---|---|---|---|
| Package | 64-pin VQFN (9x9) | 64-pin VQFN (9x9) - same | 64-pin TQFP (PT) | 64-pin VQFN (9x9) - same | 64-pin VQFN (9x9) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K |
| Max Frequency | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Flash | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB |
| SRAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| USB OTG | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) | No |
| Operating Temperature | -40C to +85C | -40C to +105C | -40C to +105C | -40C to +85C | -40C to +85C |
| I/O Pins | 53 | 53 | 53 | 53 | 53 |
| Qty-1 Price (USD) | $7.10 | $7.30 | $7.50 | $6.20 |
Principais diferenciais
- Industrial temperature grade (-40C to +85C) at standard price (vs PIC32MX440F128HT-80V/MR)
- Integrated USB 2.0 Full-Speed OTG controller (vs PIC32MX340F128HT-80I/MR)
- Higher-pin-density VQFN package (vs PIC32MX440F128H-80V/PT)
Notas de projeto
The 64-pin VQFN (9x9 mm) package has a center exposed thermal pad that MUST be soldered to a ground copper pour for both electrical reference and thermal dissipation. Use a 0.3 mm to 0.5 mm pitch via array under the EP, with vias stitched to the inner ground layer. Failing to solder the EP can cause thermal runaway at 80 MHz operation.
Place 100 nF decoupling capacitors as close as possible to every VDD/VSS pin pair. Add a bulk 4.7 uF to 10 uF ceramic on each VDD rail and a separate 1 uF for the 1.8V VCAP pin (voltage regulator output). For USB operation add a 10 uF bulk capacitor near the USB VDD pin (USBVDD).
Configure the oscillator with the correct primary oscillator configuration bits. The 80 MHz operation requires an 8 MHz primary crystal with the PLL configured to multiply by 10. Without correct FPLLIDIV and FPLLMULT settings the core will not run at full speed. Refer to the PIC32MX4xx Oscillator Configuration Diagram in the datasheet before locking the configuration bits.
Route the USB DP (RF2) and DM (RF3) signals as a 90 ohm differential pair with length matching within 150 mil. Keep the pair over a continuous ground plane and avoid routing near clock traces or switching nodes. The USB specification is highly sensitive to impedance discontinuities.
Informações de conformidade
RoHS compliant per Microchip product page and DigiKey listing. Not AEC-Q100 qualified (industrial grade MCU, not automotive).
