TLS715B0EJV50XUMA1 - 5V 150mA Auto LDO Regulator | Infineon
N.º da peça: TLS715B0EJV50XUMA1 ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $1.18 | $1,18 |
| 10 | $1.05 | $10,50 |
| 100 | $0.92 | $92,00 |
| 500 | $0.78 | $390,00 |
| 1.000 | $0.65 | $650,00 |
| 2.500 | $0.55 | $1.375,00 |
TLS715B0EJV50XUMA1 Visão geral
An LDO (low-dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage. Within the broader power-management hierarchy, the LDO sits beneath the linear regulator family, which itself falls under voltage regulators and the wider power management IC category. Unlike switching regulators, an LDO dissipates VIN - VOUT as heat but adds essentially no switching noise to the output, making it ideal for post-regulation after a noisy DC-DC stage or for direct battery-powered rails.
Key differentiating features include very low quiescent current for always-on subsystems, integrated protection such as overtemperature shutdown and output current limiting, an exposed thermal pad to lower junction-to-ambient thermal resistance, and an automotive qualification profile (AEC-Q100). The 200 mV dropout at 150 mA keeps the part in regulation even during cold-crank events on a 12 V automotive bus where the rail briefly collapses toward 5.2 V.
The TLS715B0EJV50XUMA1 uses a PNP pass-element architecture with internal bandgap reference and feedback resistors trimmed at wafer level, eliminating the need for an external resistor divider. Built on Infineon's OPTIREG linear process, the part is engineered to survive load-dump transients up to 40 V on the input.
Typical applications include automotive body and chassis ECUs, sensor and actuator supplies, instrument clusters, infotainment standby rails, and industrial 24 V bus systems. The wide 40 V input tolerance and AEC-Q100 qualification make it a common choice for ECU power trees that must ride through load-dump.
When designing with this device, place input and output ceramic capacitors as close as possible to the IC pins and provide sufficient copper area on the exposed pad to keep junction temperature within the AEC-Q100 grade limits. The 5 µA typical quiescent current makes the regulator well-suited to permanent-battery applications.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineering context beyond raw spec repetition.
Alternativas drop-in para TLS715B0EJV50XUMA1 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com TLS715B0EJV50XUMA1 (mesmo formato e footprint) — diferindo em Package, Protection Features, Input Voltage Range, Maximum Output Current, Output Voltage.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
TLS715B0EJ V33
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TLE42744DV50ATMA1
✅ Drop-In✓ Em estoque
$0.74 / unidade
Ver ficha técnica →TLE42744DV33ATMA1
✅ Drop-In✓ Em estoque
$0.74 / unidade
Ver ficha técnica →TLF80511EJV33XUMA1
✅ Drop-In✓ Em estoque
$0.65 / unidade
Ver ficha técnica →NCV4264-2C50R2G
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TLS715B0EJV50XUMA1 Classificações máximas e características elétricas
| Tipo de saída | Fixed (5.0 V) |
| Output Voltage Nominal | 5.0 V |
| Output Voltage Accuracy | ±2 % |
| Corrente máxima de saída | 150 mA |
| Faixa de tensão de entrada | Up to 40 V |
| Tensão de dropout | 200 mV typical at 150 mA |
| Corrente de repouso | 36 µA typical |
| Supply Current Max | 80 µA maximum |
| Temperatura de operação | -40 C to +125 C |
| Encapsulamento | PG-DSO-8 (exposed pad) |
| Tipo de montagem | Surface Mount |
| AEC-Q100 | Qualified |
| Status RoHS | Compliant |
| Protection Features | Overtemperature shutdown, output current limit |
| Output Polarity | Positive |
Configuração de pinos do TLS715B0EJV50XUMA1
| Pino 1 | IN — Input voltage (up to 40 V) |
| Pino 2 | GND — Ground |
| Pino 3 | GND — Ground |
| Pino 4 | NC — Not connected |
| Pino 5 | NC — Not connected |
| Pino 6 | OUT — Regulated 5.0 V output |
| Pino 7 | NC — Not connected |
| Pino 8 | NC — Not connected |
Aplicações típicas
TLS715B0EJV50XUMA1 é adequado para 6 aplicaçãos: Automotive ECU Power Supply, Industrial 24V Bus Sensor Supply, Body Control Module Standby Rail, Instrument Cluster Display Supply, Sensor and Actuator Supply in ADAS Modules, Infotainment Standby Power Rail.
Automotive ECU Power Supply
The TLS715B0EJV50XUMA1 fits automotive ECU rails because of its 40 V input tolerance and 200 mV dropout at 150 mA. According to the Infineon OPTIREG linear datasheet, the regulator rides through 12 V load-dump and cold-crank events with the output staying above 4.9 V, while AEC-Q100 grade-1 qualification supports body, chassis, and powertrain ECU designs. The 5 µA typical quiescent current keeps standby drain low for permanent-battery nodes, and the PG-DSO-8 package with exposed pad provides sufficient thermal dissipation for 5 V x 150 mA continuous loads. Placed downstream of a pre-regulator or directly on the battery rail, it post-regulates a clean 5.0 V for microcontroller, CAN transceiver, and sensor analog supplies.
Recomendado
Industrial 24V Bus Sensor Supply
The TLS715B0EJV50XUMA1 operates on industrial 24 V bus rails up to 40 V input, making it a clean post-regulator for factory sensor and instrumentation nodes. According to the Infineon datasheet, the 36 µA quiescent current suits battery-backed industrial sensors, while ±2 % output accuracy supplies ADC reference and 5 V logic rails directly. Unlike a switching regulator, it adds no EMI ripple, which matters for analog front-end and 4-20 mA loop transmitter boards.
Recomendado
Body Control Module Standby Rail
The TLS715B0EJV50XUMA1's 5 µA typical quiescent current makes it ideal for body control module standby rails that must remain alive when the ignition is off. According to the Infineon datasheet, the part draws less than 80 µA even at full load, preserving vehicle battery life over long parking periods. The fixed 5.0 V output with ±2 % accuracy directly powers wake-up logic and LIN/CAN transceivers.
Recomendado
Instrument Cluster Display Supply
The TLS715B0EJV50XUMA1 supplies a clean 5 V rail to automotive instrument cluster displays where EMI cleanliness is critical. According to the Infineon datasheet, the linear topology adds no switching noise, eliminating display artifacts and pixel jitter caused by switcher ripple. The exposed-pad PG-DSO-8 package provides adequate thermal dissipation for cluster modules mounted in confined dashboard enclosures.
Recomendado
Sensor and Actuator Supply in ADAS Modules
The TLS715B0EJV50XUMA1 powers individual sensor and actuator sub-circuits inside ADAS modules such as radar, camera, and ultrasonic sensor PCBs. According to the Infineon datasheet, the 150 mA rating covers a single sensor IC plus signal-conditioning circuitry, while the wide 40 V input tolerates shared-bus transients. AEC-Q100 grade-1 qualification supports safety-rated sensor designs.
Recomendado
Infotainment Standby Power Rail
The TLS715B0EJV50XUMA1 powers standby rails in automotive infotainment head units where the radio and telematics control unit must stay alive at all times. According to the Infineon OPTIREG linear datasheet, the low 36 µA quiescent current minimizes parasitic battery drain during parked vehicle states. The fixed 5.0 V output with ±2 % accuracy supports Bluetooth and cellular module wake-up rails without further regulation.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TLS715B0EJV50XUMA1 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TLS715B0EJ V33 | TLE42744DV50ATMA1 | TLE42744DV33ATMA1 | TLF80511EJV33XUMA1 | NCV4264-2C50R2G |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | onsemi |
| Package | PG-DSO-8 | PG-DSO-8 | PG-DSO-8 | PG-DSO-8 | PG-DSO-8 | SOIC-8 |
| Output Voltage | 5.0 V | 3.3 V | 5.0 V | 3.3 V | 3.3 V | 5.0 V |
| Maximum Output Current | 150 mA | 150 mA | 100 mA | 100 mA | 50 mA | 100 mA |
| Input Voltage Max | 40 V | 40 V | 45 V | 45 V | 45 V | 45 V |
| AEC-Q100 | Qualified | Qualified | Qualified | Qualified | Qualified | Qualified |
Principais diferenciais
- Highest output current in the TLS715B0 family (vs TLE42744DV50ATMA1)
- Lower quiescent current than cross-brand equivalent (vs NCV4264-2C50R2G)
- Exposed-pad PG-DSO-8 thermal performance (vs TLS715B0EJ V33)
Notas de projeto
Place input and output ceramic capacitors as close as possible to the IC pins to minimize parasitic inductance. According to the Infineon OPTIREG linear datasheet, a 1 µF X7R ceramic on the input and a 1 µF X7R on the output are the minimum recommended values; increasing to 2.2 µF improves load-transient response. The exposed thermal pad must be soldered to a ground copper pour of at least 50 mm² to keep theta_JA within the JEDEC JESD51-2,-5,-7 reference envelope.
Estimated: at VIN = 12 V, VOUT = 5.0 V, and 150 mA continuous load, power dissipation is roughly (12 - 5) × 0.150 = 1.05 W. According to the JEDEC JESD51-2,-5,-7 board referenced in the Infineon datasheet, theta_JA is around 50 C/W, yielding a junction-temperature rise of approximately 53 C above ambient. Ensure the ambient temperature plus this rise stays within the -40 C to +125 C AEC-Q100 grade-1 window.
Do not apply input voltages above 40 V; load-dump transients on a 12 V automotive bus can reach 35-40 V and will damage the part without sufficient headroom margin. According to the Infineon datasheet, the regulator does not include reverse-polarity protection, so an external series diode or P-MOSFET is required if reverse-battery protection is mandatory. Avoid placing the regulator downstream of a switching pre-regulator's switching node; the linear regulator's PSRR is adequate but EMI susceptibility rises if VIN is noisy.
Informações de conformidade
AEC-Q100 grade-1 qualified per Infineon OPTIREG linear datasheet. RoHS and REACH compliant per Infineon product page. Halogen-free per JEDEC JS709.
