TLV9064SIRTER - Quad 10MHz RRIO Op Amp w/ Shutdown | TI
N.º da peça: TLV9064SIRTER ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $1.65 | $1,65 |
| 10 | $1.48 | $14,80 |
| 100 | $1.32 | $132,00 |
| 500 | $1.15 | $575,00 |
| 1.000 | $0.98 | $980,00 |
| 3.000 | $0.82 | $2.460,00 |
TLV9064SIRTER Visão geral
An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output, used as a fundamental building block in analog signal conditioning. The TLV9064 belongs to the broader category of CMOS op amps (using CMOS input stages for low bias current) and the rail-to-rail family, which can swing its output to within millivolts of both supply rails. This category sits within the integrated circuits hierarchy: op amp -> amplifier IC -> analog IC -> semiconductor IC -> electronic component.
Key specifications include a unity-gain bandwidth of 10 MHz, low input offset voltage of ±0.3 mV (typical), broadband input voltage noise of 10 nV/√Hz, input bias current of 0.5 pA, and quiescent current of 538 µA per channel. The amplifier is unity-gain stable, capable of driving large capacitive loads, and incorporates internal RFI/EMI rejection filtering for robust operation in noisy environments.
The TLV9064 uses a CMOS process enabling rail-to-rail input common-mode range and rail-to-rail output swing. Shutdown logic is implemented per-channel, allowing unused channels to be placed in a high-impedance low-Iq state. According to the manufacturer datasheet, internal RFI filters suppress AM-band interference without external components, simplifying PCB layout in cost-sensitive applications.
Typical applications include signal conditioning in cost-sensitive consumer IoT sensors, low-side current sensing in battery chargers, active filtering in audio front-end paths, photodiode transimpedance stages, and ADC driver / buffer circuits for portable instrumentation. The wide supply range and shutdown feature also make it suitable for always-on industrial sensor interfaces.
When designing with this device, ensure stable operation by following the datasheet recommended feedback network for unity-gain stability, especially when driving large capacitive loads. Per-channel shutdown pins should be tied to VCC through a pull-up if shutdown is unused, otherwise the input may float and place the channel in an undefined state.
Alternativas drop-in para TLV9064SIRTER — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
TLV9062SIRTER
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TLV9064SIRTER
✅ Drop-In✓ Em estoque
$0.82 / unidade
Ver ficha técnica →TLV9064SIRTER Classificações máximas e características elétricas
| Number of Channels | 4 (Quad) |
| Amplifier Type | CMOS, Rail-to-Rail Input and Output |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Unity-Gain Bandwidth | 10 MHz |
| Input Offset Voltage | ±0.3 mV (typical) |
| Input Bias Current | 0.5 pA (typical) |
| Input Voltage Noise Density | 10 nV/√Hz |
| Quiescent Current per Channel | 538 µA (typical) |
| Tipo de saída | Rail-to-Rail |
| Shutdown Feature | Per-channel shutdown pin |
| Faixa de temperatura de operação | -40 °C to +125 °C |
| Encapsulamento | 16-WQFN (RTE) 3 mm x 3 mm |
| Tipo de montagem | Surface Mount |
| Internal RFI/EMI Filter | Yes |
| Status RoHS | Compliant |
Configuração de pinos do TLV9064SIRTER
| Pino 1 | OUTA — Channel A amplifier output |
| Pino 2 | -INA — Channel A inverting input |
| Pino 3 | +INA — Channel A non-inverting input |
| Pino 4 | V- — Negative supply (ground in single-supply operation) |
| Pino 5 | SHDNA — Channel A shutdown (active low) |
| Pino 6 | +INB — Channel B non-inverting input |
| Pino 7 | -INB — Channel B inverting input |
| Pino 8 | OUTB — Channel B amplifier output |
| Pino 9 | SHDNB — Channel B shutdown (active low) |
| Pino 10 | OUTC — Channel C amplifier output |
| Pino 11 | -INC — Channel C inverting input |
| Pino 12 | +INC — Channel C non-inverting input |
| Pino 13 | +IND — Channel D non-inverting input |
| Pino 14 | -IND — Channel D inverting input |
| Pino 15 | OUTD — Channel D amplifier output |
| Pino 16 | SHDNC/D — Channels C and D shared shutdown (active low) |
Aplicações típicas
TLV9064SIRTER é adequado para 7 aplicaçãos: Battery-Powered IoT Sensor Signal Conditioning, ADC Driver / Buffer for Multichannel Data Acquisition, Audio Front-End Active Filter Stages, Low-Side Current Sense Amplifier, Photodiode Transimpedance Amplifier (TIA), Industrial Sensor Signal Conditioning, Cost-Sensitive Consumer Electronics Active Filtering.
Battery-Powered IoT Sensor Signal Conditioning
The TLV9064SIRTER's 1.8 V to 5.5 V single-supply range, 538 µA per-channel quiescent current, and per-channel shutdown pins make it ideal for always-on IoT sensor signal conditioning in battery-powered nodes. The 10 MHz GBW comfortably handles environmental sensor bandwidths (temperature, humidity, pressure, gas) while the CMOS 0.5 pA input bias current avoids loading high-impedance sensor sources. The internal RFI/EMI filter rejects AM-band interference common in residential and industrial wireless environments. A typical circuit places one channel as a precision gain stage for a Wheatstone-bridge sensor, with the remaining channels buffering ADC inputs or active-filtering supply noise. Per-channel shutdown reduces total Iq to sub-µA when sensors are sampled infrequently, extending coin-cell lifetime.
Recomendado
ADC Driver / Buffer for Multichannel Data Acquisition
The TLV9064SIRTER's 10 MHz GBW and rail-to-rail input/output capability suit it as a buffer or driver for 12-bit to 16-bit ADCs in multichannel data-acquisition systems. The ±0.3 mV typical input offset preserves ADC dynamic range, while the 10 nV/√Hz noise floor contributes minimal jitter at the analog front-end. Each of the four channels can drive ADC inputs directly with the proper anti-alias filter network, and unused channels can be placed in shutdown to reduce system Iq. The WQFN-16 (RTE) 3x3 mm footprint places all four amps in a tight area next to the ADC, minimizing board area and trace length for low-distortion performance. Per the manufacturer datasheet, the device is unity-gain stable even with large capacitive ADC load.
Recomendado
Audio Front-End Active Filter Stages
The TLV9064SIRTER's 10 MHz GBW (well above the 20 kHz audio band) and rail-to-rail output drive make it a strong choice for active filter stages in audio front-ends, including Sallen-Key low-pass, high-pass, and band-pass topologies. The 0.5 pA CMOS input bias preserves high-impedance filter-element values without DC error, and the internal RFI filter rejects AM-band interference entering through audio cables. Each quad package can implement a stereo two-pole filter plus auxiliary channels for headphone amplifiers or microphone bias networks. The shutdown pin allows the entire filter chain to be powered down during deep-sleep audio standby, supporting headphones with always-listening wake-word features without continuous Iq overhead.
Recomendado
Low-Side Current Sense Amplifier
The TLV9064SIRTER works as a low-side current-sense amplifier in battery chargers, motor controllers, and power-path monitors when configured in a differential gain stage across a shunt resistor. The rail-to-rail input common-mode range allows the sense node to swing arbitrarily close to ground, and the 0.5 pA input bias avoids disturbing the shunt node bias. The 10 MHz GBW supports high-bandwidth current-loop monitoring for step-response and short-circuit detection. The per-channel shutdown is useful in redundant current-sensing architectures where one amplifier can be powered down for diagnostic isolation without disturbing the primary channel.
Recomendado
Photodiode Transimpedance Amplifier (TIA)
The TLV9064SIRTER's sub-pA input bias current and 10 MHz GBW suit it for photodiode transimpedance stages in optical sensors, smoke detectors, and pulse-oximetry front-ends. The CMOS input stage does not contribute significant bias current at room temperature, preserving the TIA's DC accuracy and minimizing ambient-light floor. The 10 nV/√Hz broadband noise density sets the TIA noise floor and bandwidth product for low-light detection. Four channels in one package allow multi-wavelength photodiode conditioning (e.g., red/infrared for SpO2) within a 3x3 mm footprint, while shutdown pins cut quiescent current between LED pulses.
Recomendado
Industrial Sensor Signal Conditioning
The TLV9064SIRTER's -40 °C to +125 °C operating range and 1.8 V to 5.5 V supply make it ideal for industrial sensor signal conditioning in factory automation, process control, and HVAC monitoring. The internal RFI/EMI filter rejects sub-1 GHz interference common near motor drives and switching relays in industrial cabinets. The rail-to-rail I/O handles 24 V industrial bus signals after resistive scaling, allowing direct interface to PLC analog modules. The per-channel shutdown enables energize-on-demand sensing for low-duty-cycle sensors, reducing cabinet thermal load and saving energy in densely populated control panels.
Recomendado
Cost-Sensitive Consumer Electronics Active Filtering
The TLV9064SIRTER's cost-optimized CMOS architecture and tight WQFN-16 footprint make it a strong fit for cost-sensitive consumer electronics active filters in white goods, toys, and household appliances. The 10 MHz GBW is overkill for audio-frequency filtering but allows designers to use the same op amp for both audio stages and the wideband anti-alias filters in simpler consumer ADC interfaces. The 0.5 pA input bias current preserves the high-impedance nodes typical of touch and capacitive-sensing interfaces used in modern appliance UI. Shutdown pins are valuable for battery-operated handheld consumer devices where quiescent current directly impacts standby-time spec compliance.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TLV9064SIRTER — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TLV9064IPWR | TLV9062SIRTER |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | WQFN-16 (RTE) 3x3 mm | TSSOP-16 (PW) - different package | WQFN-16 (RTE) - same |
| Number of Channels | 4 | 4 | 2 |
| Unity-Gain Bandwidth | 10 MHz | 10 MHz | 10 MHz |
| Supply Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Input Offset Voltage (typ) | ±0.3 mV | ±0.3 mV | ±0.3 mV |
| Quiescent Current per Channel | 538 µA | 538 µA | 538 µA |
| Shutdown Feature | Per-channel shutdown pin | Per-channel shutdown pin | Per-channel shutdown pin |
| Rail-to-Rail I/O | Yes (input and output) | Yes (input and output) | Yes (input and output) |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C |
Principais diferenciais
- Per-channel shutdown pins reduce total Iq to leakage levels (vs TLV9062SIRTER (dual version, same family))
- Internal RFI/EMI rejection filter eliminates external components (vs Lower-cost generic CMOS op amps without RFI rejection)
- Compact WQFN-16 3x3 mm package fits four amplifiers in tight areas (vs TLV9064IPWR (TSSOP-16 PW package))
Notas de projeto
The TLV9064SIRTER's exposed thermal pad (pin 17 / DAP) MUST be soldered to a PCB ground plane for rated thermal and electrical performance. Place input and output traces symmetrically and keep high-impedance input traces short to minimize leakage and noise pickup. Use a continuous ground plane under the WQFN-16 footprint to provide low-impedance return paths for all four amplifier channels. Per-channel supply decoupling with a 100 nF X7R ceramic capacitor placed within 2 mm of the V+ pin is recommended, with an additional 1 µF bulk capacitor on the supply node.
Each of the four channels has a dedicated shutdown pin (SHDNA, SHDNB, shared SHDNC/D). For unused shutdown pins, tie them to V+ through a 100 kΩ pull-up resistor to keep the corresponding channel active; do not leave them floating, as an undefined state may place the channel in undesired shutdown or draw excess current. Driving a shutdown pin low places that channel in high-impedance output and reduces Iq to leakage levels, useful for energize-on-demand sensing topologies.
Avoid operating the inputs beyond the rail-to-rail common-mode range, especially during input fault conditions; the CMOS input stage can phase-reverse if the input is forced more than ~0.5 V beyond either rail. For ADC-driving applications, place a 10 Ω to 100 Ω series resistor at the amplifier output to isolate capacitive ADC input loads and preserve phase margin. When driving large capacitive loads (>1 nF) directly, follow the datasheet recommended feedback capacitor values to maintain stability, otherwise oscillation may occur. Do not assume the absolute maximum ratings allow inductive kickback - use clamping diodes if switching inductive loads downstream of the amplifier output.
Informações de conformidade
RoHS and REACH compliant per TI product page. Not AEC-Q100 qualified; for automotive applications choose the TLV9064-Q1 variant. Lead-free and halogen-free per TI Material Declaration.
