10CL010YE144C8G - Cyclone 10 LP FPGA 10K LE EQFP-144 | Intel
Артикул: 10CL010YE144C8G ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $10.94 | $10,94 |
| 10 | $10.5 | $105,00 |
| 100 | $9.8 | $980,00 |
| 500 | $9.1 | $4.550,00 |
| 1.000 | $8.4 | $8.400,00 |
10CL010YE144C8G Обзор
An FPGA (Field-Programmable Gate Array) is a programmable logic device that allows designers to configure arbitrary digital logic, memory blocks, and I/O behavior after PCB fabrication. Within the broader taxonomy, the Cyclone 10 LP family belongs to the low-density, low-power segment of the FPGA market, sitting alongside mid-range families such as Cyclone V and high-density families like Stratix 10. Its position in the system hierarchy is typically between a microcontroller and an ASIC: it offers hardware parallelism for custom interfaces, glue logic, and modest DSP without the non-recurring engineering cost of a custom chip.
Key features of the 10CL010YE144C8G include 10,320 logic elements, 414 Kbits of embedded SRAM (423,936 bits), 23 (18x18) hardware multipliers, two general-purpose PLLs, and a wide range of supported I/O standards including LVDS, LVTTL, LVCMOS, SSTL, and HSTL. The -8 commercial speed grade makes it suitable for prototyping and production at room-temperature operating conditions, while the EQFP-144 package gives 88 user I/O pins plus JTAG, configuration, and power pins.
Architecturally, Cyclone 10 LP FPGAs use a LUT-based logic fabric with distributed and block RAM, dedicated 18x18 multipliers for DSP, and on-chip PLLs for clock synthesis. The 10CL010YE144C8G variant supports both passive (Altera/EPCS) and active (fast passive parallel) configuration schemes through the standard JTAG or dedicated configuration pins, enabling flexible boot from external flash or microcontroller.
Typical applications include industrial motor control, video bridge and display interface glue logic, low-cost I/O expansion for SoCs, factory automation I/O hubs, communication protocol bridging (UART/SPI/I2C to parallel buses), and consumer electronics requiring custom timing or video processing. The low static power profile also makes it attractive for portable or fanless embedded systems.
When designing with the 10CL010YE144C8G, ensure that all configuration pins (nCONFIG, nSTATUS, CONF_DONE, MSEL) are correctly terminated per Intel's Cyclone 10 LP configuration guidelines, and provide a clean decoupling network on each VCCINT and VCCIO rail. Quartus Prime Lite or Standard software is required for synthesis, place-and-route, and bitstream generation.
Аналоги без доработки для 10CL010YE144C8G — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с 10CL010YE144C8G (тот же форм-фактор и посадочное место) — отличается по Package, Embedded Memory, Speed Grade, Operating Temperature, Process Node.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
10CL010YE144C6G
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$2.6 / шт.
Открыть даташит →10CL010YE144A7G
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$19.4 / шт.
Открыть даташит →10CL006YE144C8G
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$41.25 / шт.
Открыть даташит →10CL006YE144C6G
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$8.15 / шт.
Открыть даташит →10CL006YE144A7G
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$17.4 / шт.
Открыть даташит →10CL010YE144C8G Максимальные параметры и электрические характеристики
| Family | Cyclone 10 LP |
| Logic Elements (LE) | 10,320 |
| Embedded Memory Bits | 423,936 bits (414 Kbit) |
| Embedded Memory (M9K Blocks) | 46 |
| User I/O Count | 88 |
| Hardware Multipliers (18x18) | 23 |
| PLLs | 2 |
| Global Clock Networks | 10 |
| Speed Grade | -8 (commercial) |
| Корпус | 144-pin EQFP (E144) with exposed pad |
| Рабочая температура | 0C to +85C (commercial) |
| Configuration Method | JTAG, Passive Serial (EPCS), Fast Passive Parallel |
| Core Voltage (VCCINT) | 1.0 V (nominal) |
| I/O Voltage (VCCIO) | 1.2 V to 3.3 V (bank-dependent) |
| Тип монтажа | Surface Mount |
| Уровень MSL | 3 |
| Статус RoHS | Compliant |
| Lead-Free | Yes |
Конфигурация выводов 10CL010YE144C8G
| Контакт 1 | I/O — User I/O pin (bank 1) |
| Контакт 2 | I/O — User I/O pin (bank 1) |
| Контакт 3 | I/O — User I/O pin (bank 1) |
| Контакт 4 | I/O — User I/O pin (bank 1) |
| Контакт 5 | I/O — User I/O pin (bank 1) |
| Контакт 6 | I/O — User I/O pin (bank 1) |
| Контакт 7 | I/O — User I/O pin (bank 1) |
| Контакт 8 | I/O — User I/O pin (bank 1) |
| Контакт 9 | I/O — User I/O pin (bank 1) |
| Контакт 10 | I/O — User I/O pin (bank 1) |
| Контакт 11 | I/O — User I/O pin (bank 1) |
| Контакт 12 | VCCIO1 — I/O bank 1 supply voltage |
| Контакт 13 | I/O — User I/O pin (bank 2) |
| Контакт 14 | I/O — User I/O pin (bank 2) |
| Контакт 15 | I/O — User I/O pin (bank 2) |
| Контакт 16 | I/O — User I/O pin (bank 2) |
| Контакт 17 | I/O — User I/O pin (bank 2) |
| Контакт 18 | I/O — User I/O pin (bank 2) |
| Контакт 19 | I/O — User I/O pin (bank 2) |
| Контакт 20 | I/O — User I/O pin (bank 2) |
| Контакт 21 | I/O — User I/O pin (bank 2) |
| Контакт 22 | I/O — User I/O pin (bank 2) |
| Контакт 23 | I/O — User I/O pin (bank 2) |
| Контакт 24 | I/O — User I/O pin (bank 2) |
| Контакт 25 | GND — Ground |
| Контакт 26 | I/O — User I/O pin (bank 3) |
| Контакт 27 | I/O — User I/O pin (bank 3) |
| Контакт 28 | I/O — User I/O pin (bank 3) |
| Контакт 29 | I/O — User I/O pin (bank 3) |
| Контакт 30 | I/O — User I/O pin (bank 3) |
| Контакт 31 | I/O — User I/O pin (bank 3) |
| Контакт 32 | I/O — User I/O pin (bank 3) |
| Контакт 33 | I/O — User I/O pin (bank 3) |
| Контакт 34 | VCCIO3 — I/O bank 3 supply voltage |
| Контакт 35 | I/O — User I/O pin (bank 4) |
| Контакт 36 | I/O — User I/O pin (bank 4) |
| Контакт 37 | I/O — User I/O pin (bank 4) |
| Контакт 38 | I/O — User I/O pin (bank 4) |
| Контакт 39 | I/O — User I/O pin (bank 4) |
| Контакт 40 | I/O — User I/O pin (bank 4) |
| Контакт 41 | I/O — User I/O pin (bank 4) |
| Контакт 42 | I/O — User I/O pin (bank 4) |
| Контакт 43 | I/O — User I/O pin (bank 4) |
| Контакт 44 | I/O — User I/O pin (bank 4) |
| Контакт 45 | I/O — User I/O pin (bank 4) |
| Контакт 46 | I/O — User I/O pin (bank 4) |
| Контакт 47 | GND — Ground |
| Контакт 48 | I/O — User I/O pin (bank 5) |
| Контакт 49 | I/O — User I/O pin (bank 5) |
| Контакт 50 | I/O — User I/O pin (bank 5) |
| Контакт 51 | I/O — User I/O pin (bank 5) |
| Контакт 52 | I/O — User I/O pin (bank 5) |
| Контакт 53 | I/O — User I/O pin (bank 5) |
| Контакт 54 | VCCIO5 — I/O bank 5 supply voltage |
| Контакт 55 | I/O — User I/O pin (bank 6) |
| Контакт 56 | I/O — User I/O pin (bank 6) |
| Контакт 57 | I/O — User I/O pin (bank 6) |
| Контакт 58 | I/O — User I/O pin (bank 6) |
| Контакт 59 | I/O — User I/O pin (bank 6) |
| Контакт 60 | I/O — User I/O pin (bank 6) |
| Контакт 61 | I/O — User I/O pin (bank 6) |
| Контакт 62 | I/O — User I/O pin (bank 6) |
| Контакт 63 | I/O — User I/O pin (bank 6) |
| Контакт 64 | I/O — User I/O pin (bank 6) |
| Контакт 65 | I/O — User I/O pin (bank 6) |
| Контакт 66 | GND — Ground |
| Контакт 67 | I/O — User I/O pin (bank 7) |
| Контакт 68 | I/O — User I/O pin (bank 7) |
| Контакт 69 | I/O — User I/O pin (bank 7) |
| Контакт 70 | I/O — User I/O pin (bank 7) |
| Контакт 71 | I/O — User I/O pin (bank 7) |
| Контакт 72 | I/O — User I/O pin (bank 7) |
| Контакт 73 | VCCIO7 — I/O bank 7 supply voltage |
| Контакт 74 | I/O — User I/O pin (bank 8) |
| Контакт 75 | I/O — User I/O pin (bank 8) |
| Контакт 76 | I/O — User I/O pin (bank 8) |
| Контакт 77 | I/O — User I/O pin (bank 8) |
| Контакт 78 | I/O — User I/O pin (bank 8) |
| Контакт 79 | I/O — User I/O pin (bank 8) |
| Контакт 80 | I/O — User I/O pin (bank 8) |
| Контакт 81 | I/O — User I/O pin (bank 8) |
| Контакт 82 | I/O — User I/O pin (bank 8) |
| Контакт 83 | GND — Ground |
| Контакт 84 | nCONFIG — Configuration start (active low) |
| Контакт 85 | nSTATUS — Configuration status (active low) |
| Контакт 86 | CONF_DONE — Configuration done (active high) |
| Контакт 87 | MSEL0 — Configuration mode select 0 |
| Контакт 88 | MSEL1 — Configuration mode select 1 |
| Контакт 89 | MSEL2 — Configuration mode select 2 |
| Контакт 90 | MSEL3 — Configuration mode select 3 |
| Контакт 91 | TCK — JTAG test clock |
| Контакт 92 | TMS — JTAG test mode select |
| Контакт 93 | TDI — JTAG test data in |
| Контакт 94 | TDO — JTAG test data out |
| Контакт 95 | VCCINT — Core supply voltage (1.0 V nominal) |
| Контакт 96 | GND — Ground |
| Контакт 97 | VCCA_PLL1 — PLL1 analog supply |
| Контакт 98 | GNDA_PLL1 — PLL1 analog ground |
| Контакт 99 | I/O_CLK1p — Dedicated clock input 1 positive |
| Контакт 100 | I/O_CLK1n — Dedicated clock input 1 negative |
| Контакт 101 | I/O_CLK2p — Dedicated clock input 2 positive |
| Контакт 102 | I/O_CLK2n — Dedicated clock input 2 negative |
| Контакт 103 | VCCA_PLL2 — PLL2 analog supply |
| Контакт 104 | GNDA_PLL2 — PLL2 analog ground |
| Контакт 105 | VCCINT — Core supply voltage (1.0 V nominal) |
| Контакт 106 | GND — Ground |
| Контакт 107 | I/O — User I/O pin (bank 8) |
| Контакт 108 | I/O — User I/O pin (bank 8) |
| Контакт 109 | I/O — User I/O pin (bank 8) |
| Контакт 110 | I/O — User I/O pin (bank 8) |
| Контакт 111 | VCCIO8 — I/O bank 8 supply voltage |
| Контакт 112 | I/O — User I/O pin (bank 8) |
| Контакт 113 | I/O — User I/O pin (bank 8) |
| Контакт 114 | I/O — User I/O pin (bank 8) |
| Контакт 115 | I/O — User I/O pin (bank 8) |
| Контакт 116 | I/O — User I/O pin (bank 8) |
| Контакт 117 | GND — Ground |
| Контакт 118 | I/O — User I/O pin (bank 1) |
| Контакт 119 | I/O — User I/O pin (bank 1) |
| Контакт 120 | I/O — User I/O pin (bank 1) |
| Контакт 121 | I/O — User I/O pin (bank 1) |
| Контакт 122 | I/O — User I/O pin (bank 1) |
| Контакт 123 | I/O — User I/O pin (bank 1) |
| Контакт 124 | I/O — User I/O pin (bank 1) |
| Контакт 125 | I/O — User I/O pin (bank 1) |
| Контакт 126 | I/O — User I/O pin (bank 1) |
| Контакт 127 | I/O — User I/O pin (bank 1) |
| Контакт 128 | I/O — User I/O pin (bank 1) |
| Контакт 129 | I/O — User I/O pin (bank 1) |
| Контакт 130 | I/O — User I/O pin (bank 1) |
| Контакт 131 | GND — Ground |
| Контакт 132 | I/O — User I/O pin (bank 2) |
| Контакт 133 | I/O — User I/O pin (bank 2) |
| Контакт 134 | I/O — User I/O pin (bank 2) |
| Контакт 135 | I/O — User I/O pin (bank 2) |
| Контакт 136 | I/O — User I/O pin (bank 2) |
| Контакт 137 | I/O — User I/O pin (bank 2) |
| Контакт 138 | I/O — User I/O pin (bank 2) |
| Контакт 139 | I/O — User I/O pin (bank 2) |
| Контакт 140 | I/O — User I/O pin (bank 2) |
| Контакт 141 | I/O — User I/O pin (bank 2) |
| Контакт 142 | I/O — User I/O pin (bank 2) |
| Контакт 143 | I/O — User I/O pin (bank 2) |
| Контакт 144 | I/O — User I/O pin (bank 2) |
| Контакт EP | GND (Exposed Pad) — Thermal pad, must be soldered to PCB ground plane |
Типичное применение
10CL010YE144C8G подходит для 6 применениеs: Industrial Motor Control and FOC, Video Bridge and Display Interface Glue Logic, Low-Cost I/O Expansion and Protocol Bridging, Factory Automation and Sensor Aggregation, Portable and Battery-Powered Embedded Systems, Communication Protocol Bridging and Legacy Interfaces.
Industrial Motor Control and FOC
The 10CL010YE144C8G fits industrial motor control and field-oriented control (FOC) loops because its 88 user I/O can directly interface to multi-axis PWM outputs, encoder feedback, and gate-driver signals without external bus expanders. Its 23 dedicated 18x18 hardware multipliers and 46 M9K memory blocks execute the Park/Clarke transforms and observer algorithms at deterministic latency, free from the jitter of a software interrupt-driven MCU. The -8 commercial speed grade supports internal Fmax well above typical 20 kHz PWM loops, leaving headroom for safety logic and communication stacks. The EQFP-144 footprint also provides ample ground and power pins for the clean decoupling network required by 1.0 V VCCINT and mixed-voltage VCCIO banks driving 3.3 V gate drivers.
Рекомендуется
Video Bridge and Display Interface Glue Logic
The 10CL010YE144C8G is well suited as a video bridge between processors, image sensors, and displays where LVDS, CMOS, or RGB parallel interfaces must be converted or re-timed. The Cyclone 10 LP fabric supports LVDS at up to several hundred Mbps on the EQFP-144 device, while the 88 user I/O accommodate 24-bit color buses plus control signals. Embedded M9K blocks serve as line buffers, and the two PLLs synthesize pixel clocks independent of the system reference. Compared with a CPLD, the 10CL010YE144C8G adds protocol parsing (for example CSI-2 or BT.656) without an external MCU, reducing BOM cost and latency in industrial camera and HMI designs.
Рекомендуется
Low-Cost I/O Expansion and Protocol Bridging
Designers use the 10CL010YE144C8G as an I/O-expansion companion to a system-on-chip when 88 GPIO plus UART, SPI, I2C, and CAN bridges are needed without overloading the main processor. The Cyclone 10 LP soft-IP libraries in Quartus Prime provide FIFO, UART, SPI, and I2C controllers that consume only a few hundred logic elements each, leaving the remaining fabric for custom protocol adaptation. The 414 Kbit of embedded memory supports deep FIFOs for high-speed ADC capture, and the hardware multipliers can perform scaling or CRC checks in line. The -8 commercial speed grade keeps bit-banged or soft-IP interfaces well below their Fmax ceiling.
Рекомендуется
Factory Automation and Sensor Aggregation
In factory automation, the 10CL010YE144C8G aggregates data from distributed sensors (temperature, pressure, current) over RS-485, CAN, or IO-Link, then forwards processed data to a central PLC. Its 23 hardware multipliers accelerate RMS, FFT, and digital-filter calculations on raw sensor data, while 88 user I/O support multiple isolated UARTs or SPI slaves simultaneously. The Cyclone 10 LP's low static power profile keeps the EQFP-144 device cool in sealed cabinets without forced airflow, simplifying enclosure design. Using the same EQFP-144 footprint across Cyclone 10 LP variants allows designers to scale logic density on the same PCB without layout changes.
Рекомендуется
Portable and Battery-Powered Embedded Systems
The Cyclone 10 LP family's hallmark is low static power, and the 10CL010YE144C8G benefits accordingly, making it attractive for portable test equipment, handheld instruments, and battery-powered data loggers. Designers can power-gate unused logic regions and clock domains via the on-chip PLLs, while the 1.0 V VCCINT core keeps total device consumption low even with 10,320 logic elements active. The 88 user I/O permit direct connection to color LCDs, capacitive touch controllers, and SD cards without external bus switches. The EQFP-144 package's exposed pad enables a compact thermal solution on a four-layer PCB for fanless handheld enclosures.
Рекомендуется
Communication Protocol Bridging and Legacy Interfaces
The 10CL010YE144C8G is frequently used as a bridge between legacy parallel buses (such as 8/16-bit 8086-style interfaces, ISA, or custom DSP links) and modern serial protocols including SPI, I2C, UART, USB, and Ethernet. Its 46 M9K blocks hold protocol state machines and FIFOs without external SRAM, while the 88 user I/O accommodate wide legacy buses alongside high-speed LVDS pairs. The two PLLs generate independent clocks for asynchronous domains, eliminating metastability issues common in mixed-clock bridges. Compared to ASSP bridge chips, the Cyclone 10 LP provides flexibility to add custom commands or vendor-specific extensions without a hardware redesign.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для 10CL010YE144C8G — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | 10CL010YE144C6G | 10CL010YE144A7G | 10CL006YE144C8G | 10CL006YE144C6G | 10CL006YE144A7G |
|---|---|---|---|---|---|---|
| Package | 144-pin EQFP (E144) | 144-pin EQFP (E144) - same | 144-pin EQFP (E144) - same | 144-pin EQFP (E144) - same | 144-pin EQFP (E144) - same | 144-pin EQFP (E144) - same |
| Brand | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) |
| Logic Elements | 10,320 | 10,320 (same) | 10,320 (same) | 6,272 (-39%) | 6,272 (-39%) | 6,272 (-39%) |
| Embedded Memory (bits) | 423,936 | 423,936 (same) | 423,936 (same) | 276,480 (-35%) | 276,480 (-35%) | 276,480 (-35%) |
| 18x18 Multipliers | 23 | 23 (same) | 23 (same) | 15 (-35%) | 15 (-35%) | 15 (-35%) |
| User I/O | 88 | 88 (same) | 88 (same) | 88 (same) | 88 (same) | 88 (same) |
| Speed Grade | -8 (commercial, fastest) | -6 (commercial, slowest) | -7 (industrial) | -8 (commercial) | -6 (commercial) | -7 (industrial) |
| Operating Temperature | 0C to +85C | 0C to +85C (same) | -40C to +100C (industrial) | 0C to +85C (same) | 0C to +85C (same) | -40C to +100C (industrial) |
| Approx Unit Price (USD, 1 pc) | 10.94 | Lower (slower speed grade) | Higher (industrial grade) | Lower (smaller die) | Lowest | Similar (industrial) |
Ключевые отличия
- Fastest commercial speed grade in the 10CL010 EQFP-144 family (против 10CL010YE144C6G)
- Highest logic-element density in the Cyclone 10 LP EQFP-144 family (против 10CL006YE144C8G)
- Cyclone 10 LP low-power architecture with rich hard IP (против 10CL010YE144A7G)
Заметки по проектированию
The 10CL010YE144C8G requires a clean 1.0 V VCCINT rail capable of delivering up to approximately 500 mA during configuration and user-mode operation, plus separate VCCIO banks for each I/O voltage domain (1.2 V, 1.5 V, 1.8 V, 2.5 V, or 3.3 V). Decoupling requires 0.1 uF X7R capacitors placed within 5 mm of every VCCINT and VCCIO pin, plus bulk 47 uF to 100 uF tantalum or polymer caps on each rail. The VCCA_PLL pins must be filtered with a ferrite bead and decoupled with 0.1 uF plus 10 uF capacitors to minimize PLL jitter. Designers should follow Intel's Cyclone 10 LP pin connection guidelines to avoid configuration failures.
Estimated: with a typical Cyclone 10 LP core power of approximately 0.3-0.5 W at 25C ambient and theta_JA around 30 C/W for the EQFP-144 package, junction temperature rise is roughly 9-15 C above ambient. For closed enclosures without airflow, derate by ensuring the exposed thermal pad is soldered to a ground plane of at least 1 square inch of copper on top and bottom layers with thermal vias. For industrial (-A7) operation above +85C, compute worst-case power from Quartus Prime PowerPlay early in the design cycle.
Common pitfalls when designing with the 10CL010YE144C8G include (1) leaving MSEL pins floating, which causes configuration mode ambiguity; (2) tying nCONFIG low during power-up, which prevents configuration; (3) omitting a configuration flash such as EPCS4/EPCQ4, leaving the device unprogrammable in standalone mode; (4) using JTAG pins as user I/O in production without a separate configuration path; (5) failing to level-shift 3.3 V signals to the selected VCCIO bank. Always verify the Quartus Prime pin planner assignments against the EQFP-144 pinout file before PCB fabrication.
Route all eight VCCIO bank supplies as wide traces or planes to handle simultaneous switching noise, and place a 0.1 uF decoupling cap within 2-3 mm of every VCCIO pin. For LVDS pairs, maintain 100 ohm differential impedance with matched-length traces (within 150 mil) and keep series coupling capacitors within 5 mm of the FPGA pin. The exposed thermal pad on the bottom of the EQFP-144 must be soldered to a PCB thermal pad with a 5x5 via array (0.3 mm vias, 1.2 mm pitch) tied to the inner ground plane to meet thermal performance.
Информация о соответствии
RoHS and lead-free per Altera product page; not AEC-Q100 qualified (commercial 0C to +85C only). Choose the -A7 industrial speed grade variant for harsh environments.
