10M04DCF256A7G - MAX 10 FPGA 4K LE 256-FBGA | Intel
Артикул: 10M04DCF256A7G ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $17.35 | $17,35 |
| 10 | $15.62 | $156,20 |
| 100 | $13.88 | $1.388,00 |
| 500 | $12.45 | $6.225,00 |
| 1.000 | $11.1 | $11.100,00 |
10M04DCF256A7G Обзор
What is a MAX 10 FPGA? The MAX 10 family belongs to the low-cost, non-volatile FPGA product line within Intel's programmable logic portfolio. As an FPGA (Field Programmable Gate Array), the device provides programmable logic blocks, embedded memory, and DSP blocks that can be reconfigured post-manufacturing. MAX 10 specifically targets small-form-factor, low-power applications by integrating hard IP such as ADCs, PLLs, and configuration memory into the same die, blurring the line between traditional FPGAs and microcontrollers in embedded designs.
The 10M04 variant delivers 4,000 logic elements (LEs), 16 Kbits of user flash memory (UFM) for data storage, 1.5 Mbits of total embedded block RAM, and 178 maximum user I/O pins. Additional features include up to 72 Kbits of distributed RAM (in MLABs), a 12-bit 1 MSPS analog-to-digital converter (ADC), and on-chip voltage regulation supporting single 3.0 V or 3.3 V supply operation.
Architecturally, MAX 10 devices combine a LUT-based logic fabric with hardened analog and memory blocks, allowing single-chip implementation of glue logic, state machines, and sensor interfacing. The integrated dual-configuration flash supports remote field updates and design version rollback without external memory. Internal flash and SRAM-based configuration cells enable instant-on behavior, making the device suitable for deterministic boot applications.
Typical applications include industrial control and I/O expansion, low-cost video processing bridges, motor control and drive interfaces, portable test and measurement, automotive infotainment and body controllers, and consumer electronics requiring custom logic or interface translation. The 256-FBGA package and high I/O count target PCB designs with moderate routing complexity.
Designers should leverage the Quartus Prime software for synthesis and place-and-route, and consult the MAX 10 device handbook for pinout, configuration scheme, and ADC calibration procedures. The exposed pad must be soldered to the PCB ground plane for thermal dissipation and signal integrity.
This page synthesizes distributor pricing, same-family MAX 10 alternatives, and practical design notes not found in the manufacturer datasheet alone, enabling faster component selection and BOM validation.
Аналоги без доработки для 10M04DCF256A7G — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с 10M04DCF256A7G (тот же форм-фактор и посадочное место) — отличается по Package, Process Technology, Logic Elements (LE), User Flash Memory, User I/O Count.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
10M04DAF256A7G
✅ Прямая замена✓ В наличии
$3.53 / шт.
Открыть даташит →10M04DAF256C7G
✅ Прямая замена✓ В наличии
$9.45 / шт.
Открыть даташит →10M04DCF256C8G
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
10M02DCU324A7G
✅ Прямая замена✓ В наличии
$6.3 / шт.
Открыть даташит →10M04DAU324I7G
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$13.5 / шт.
Открыть даташит →10M04DCF256A7G Максимальные параметры и электрические характеристики
| Series | MAX 10 |
| Logic Elements (LE) | 4,000 |
| Maximum User I/O | 178 |
| Embedded Memory (M9K) | 193,536 bits |
| Total RAM | 1.5 Mbit |
| User Flash Memory (UFM) | 16 Kbit |
| Process Technology | 55 nm |
| Core Voltage | 1.2 V |
| Корпус | 256-LBGA (FBGA) |
| Тип монтажа | Surface Mount |
| Рабочая температура | -40C to +125C (Industrial) |
| Configuration Memory | Internal dual-configuration flash (instant-on) |
| Integrated ADC | 12-bit, 1 MSPS |
| Статус RoHS | Compliant |
Руководство по цоколевке 10M04DCF256A7G в корпусе 256-lbga (fbga)
Цоколевка для 10M04DCF256A7G (корпус 256-lbga (fbga)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для 10M04DCF256A7G.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
10M04DCF256A7G подходит для 7 применениеs: Industrial Control and I/O Expansion, Motor Control and Drive Interfaces, Portable Test and Measurement, Automotive Infotainment and Body Controllers, Video Processing Bridges and Format Conversion, Consumer Electronics Custom Logic, Communication Protocol Bridging.
Industrial Control and I/O Expansion
The 10M04DCF256A7G suits industrial PLC and I/O expansion modules where deterministic logic and 178 GPIO enable multi-protocol interfacing. The MAX 10's instant-on dual-configuration flash eliminates boot delay, critical for factory automation requiring sub-100ms power-up. Integrated 12-bit ADC supports sensor signal conditioning, while 55nm process ensures low power dissipation under continuous industrial operation. Compared to discrete MCU + CPLD designs, the 10M04 consolidates glue logic, state machines, and protocol bridging (RS-485, CAN, SPI, I2C) into a single 256-FBGA device, reducing BOM and PCB area.
Рекомендуется
Motor Control and Drive Interfaces
The 10M04DCF256A7G's 4K logic elements and 178 I/O enable field-oriented control (FOC) and PWM generation for 3-phase motor drives up to several kW. Hardware multipliers and DSP blocks accelerate Park/Clarke transforms, while 1.5 Mbit embedded RAM stores lookup tables and filter coefficients. The integrated ADC samples current and voltage feedback synchronously to PWM, reducing latency versus external ADC chains. Industrial temperature grade (-40C to +125C) and 256-FBGA thermal performance support enclosed drive enclosures with forced-air cooling.
Рекомендуется
Portable Test and Measurement
The 10M04DCF256A7G is well-suited for handheld oscilloscopes, logic analyzers, and portable data acquisition systems. Its 12-bit integrated ADC samples at 1 MSPS for mid-bandwidth signal capture, while 4K logic elements implement triggering, protocol decoding (I2C/SPI/UART), and display drivers. Single 3.3V supply operation with internal voltage regulation simplifies power tree design. The 256-FBGA package offers 178 I/O for multi-channel front-end multiplexing, and instant-on flash configuration reduces battery drain during standby.
Рекомендуется
Automotive Infotainment and Body Controllers
The 10M04DCF256A7G's industrial temperature range and 178 GPIO enable body control modules, lighting controllers, and infotainment I/O bridging in automotive designs. MAX 10 non-volatile flash supports OTA (over-the-air) firmware updates with design rollback capability, critical for vehicle recall mitigation. The integrated ADC monitors battery voltage, temperature, and illumination sensors directly. Note: this part is industrial-grade; AEC-Q100 qualified variants in the MAX 10 family should be selected for safety-critical automotive applications.
Рекомендуется
Video Processing Bridges and Format Conversion
The 10M04DCF256A7G provides LVDS, CMOS, and DDR memory interfaces for video format conversion (RGB to MIPI, HDMI to LVDS) in display panels and embedded vision systems. With 1.5 Mbit embedded block RAM, the device buffers video frames while 4K logic elements implement scaling, color space conversion, and timing generation. The 256-FBGA package supports the high pin count required for parallel video buses, and internal flash stores default boot images for instant-on display initialization.
Рекомендуется
Consumer Electronics Custom Logic
The 10M04DCF256A7G integrates custom user interfaces, LED matrix driving, and peripheral glue logic in consumer products like smart appliances, gaming peripherals, and home audio. The 12-bit ADC reads capacitive touch sensors and analog control knobs, while PWM outputs drive LED dimming at up to hundreds of kHz. Instant-on flash configuration enables immediate user response at power-up, a UX advantage over MCU boot sequences. The 256-FBGA and -40C to +125C rating suit thermally constrained consumer enclosures.
Рекомендуется
Communication Protocol Bridging
The 10M04DCF256A7G bridges legacy and modern serial interfaces (UART, SPI, I2C, CAN, USB, Ethernet) in embedded gateways. Its 178 GPIO accommodate multiple parallel protocol buses, while 4K logic elements implement protocol stack layers and timing-critical state machines. Dual-configuration flash allows field upgrades of bridge firmware without external memory, and the 55nm process ensures low standby power for always-on IoT edge devices. Industrial temperature grade supports outdoor and industrial installations.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для 10M04DCF256A7G — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | 10M04DAF256A7G | 10M04DAF256C7G | 10M04DCF256C8G |
|---|---|---|---|---|
| Package | 256-LBGA (F256) | 256-LBGA (F256) - same | 256-LBGA (F256) - same | 256-LBGA (F256) - same |
| Brand | Intel | Intel - same | Intel - same | Intel - same |
| Logic Elements | 4,000 | 4,000 | 4,000 | 4,000 |
| Maximum User I/O | 178 | 178 | 178 | 178 |
| Embedded Memory (M9K) | 193,536 bits | 193,536 bits | 193,536 bits | 193,536 bits |
| Speed Grade | A7 (standard) | A7 (standard) | C7 (commercial) | C8 (commercial) |
| Operating Temperature | -40C to +125C (Industrial) | -40C to +125C (Industrial) | 0C to +85C (Commercial) | 0C to +85C (Commercial) |
| Integrated ADC | 12-bit, 1 MSPS | 12-bit, 1 MSPS | 12-bit, 1 MSPS | 12-bit, 1 MSPS |
Ключевые отличия
- Internal dual-configuration flash eliminates external boot PROM (против 10M04DAF256A7G)
- Industrial temperature grade for harsh environments (против 10M04DCF256C8G)
- Integrated 12-bit ADC eliminates external sampling ICs (против Lattice MachXO2)
Заметки по проектированию
The 256-FBGA package requires the central exposed pad to be soldered to a PCB ground plane for thermal dissipation. Estimated: at typical 1.2V core and 100mA active current, power dissipation is approximately 120mW, well within passive cooling limits. For continuous high-utilization designs (above 80% LE and DSP usage), provide at least 4 thermal vias under the exposed pad to a 2oz copper inner ground layer to keep junction temperature below 100C in enclosed industrial enclosures.
Route differential pairs (LVDS, DDR) with 100 ohm differential impedance and length-matched within 150 mils for signal integrity. Place decoupling capacitors (100nF + 10uF bulk) within 100 mils of each power pin. For MAX 10 devices, separate analog AVDD and digital VCCINT supplies with ferrite beads to prevent ADC noise coupling. According to the MAX 10 hardware design guidelines, JTAG pins (TCK, TMS, TDI, TDO) require 4.7k pull-ups on TCK and TMS for reliable configuration.
Do not confuse the 10M04DCF256A7G (industrial, A7 speed) with the 10M04DCF256C8G (commercial, C8 speed) when sourcing for industrial applications - the C8 variant lacks the -40C to +125C rating. Configuration mode (AS, PS, JTAG) must be set via MSEL pins at power-up; incorrect MSEL strapping causes silent configuration failure. The dual-configuration flash requires Quartus Prime conversion to .pof format - .sof files only program SRAM and are lost at power-down.
Place the 256-FBGA on the top side of the PCB with a 4-layer stack-up (signal-ground-power-signal) for optimal signal integrity. Use microvia or via-in-pad technology for inner-row balls to route out from the dense 1.0mm pitch array. Per Intel's MAX 10 layout guidelines, keep all high-speed traces on the top layer directly above a continuous ground plane to minimize return path inductance.
Информация о соответствии
RoHS compliant per Altera/Intel product page. Industrial temperature grade (-40C to +125C) but NOT AEC-Q100 qualified; for automotive safety-critical applications use MAX 10 AEC-Q100 variants. Halogen-free status not explicitly stated in verified data.
