10M04DCF256A7G - MAX 10 FPGA 4K LE 256-FBGA | Intel
料号： 10M04DCF256A7G ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $17.35 | $17.35 |
| 10 | $15.62 | $156.20 |
| 100 | $13.88 | $1,388.00 |
| 500 | $12.45 | $6,225.00 |
| 1,000 | $11.1 | $11,100.00 |
10M04DCF256A7G 概述
What is a MAX 10 FPGA? The MAX 10 family belongs to the low-cost, non-volatile FPGA product line within Intel's programmable logic portfolio. As an FPGA (Field Programmable Gate Array), the device provides programmable logic blocks, embedded memory, and DSP blocks that can be reconfigured post-manufacturing. MAX 10 specifically targets small-form-factor, low-power applications by integrating hard IP such as ADCs, PLLs, and configuration memory into the same die, blurring the line between traditional FPGAs and microcontrollers in embedded designs.
The 10M04 variant delivers 4,000 logic elements (LEs), 16 Kbits of user flash memory (UFM) for data storage, 1.5 Mbits of total embedded block RAM, and 178 maximum user I/O pins. Additional features include up to 72 Kbits of distributed RAM (in MLABs), a 12-bit 1 MSPS analog-to-digital converter (ADC), and on-chip voltage regulation supporting single 3.0 V or 3.3 V supply operation.
Architecturally, MAX 10 devices combine a LUT-based logic fabric with hardened analog and memory blocks, allowing single-chip implementation of glue logic, state machines, and sensor interfacing. The integrated dual-configuration flash supports remote field updates and design version rollback without external memory. Internal flash and SRAM-based configuration cells enable instant-on behavior, making the device suitable for deterministic boot applications.
Typical applications include industrial control and I/O expansion, low-cost video processing bridges, motor control and drive interfaces, portable test and measurement, automotive infotainment and body controllers, and consumer electronics requiring custom logic or interface translation. The 256-FBGA package and high I/O count target PCB designs with moderate routing complexity.
Designers should leverage the Quartus Prime software for synthesis and place-and-route, and consult the MAX 10 device handbook for pinout, configuration scheme, and ADC calibration procedures. The exposed pad must be soldered to the PCB ground plane for thermal dissipation and signal integrity.
This page synthesizes distributor pricing, same-family MAX 10 alternatives, and practical design notes not found in the manufacturer datasheet alone, enabling faster component selection and BOM validation.
直接替换替代料： 10M04DCF256A7G ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： 10M04DCF256A7G （相同外形与封装尺寸） ——差异在于 Package, Process Technology, Logic Elements (LE), User Flash Memory, User I/O Count.
快速对比工具——选择替代料号进行并排对比：
10M04DAF256A7G
✅ 直接替换✓ 有现货
$3.53 / 个
查看数据手册 →10M04DAF256C7G
✅ 直接替换✓ 有现货
$9.45 / 个
查看数据手册 →10M04DCF256C8G
✅ 直接替换📋 参考替代料（不在目录中）
10M02DCU324A7G
✅ 直接替换✓ 有现货
$6.3 / 个
查看数据手册 →10M04DAU324I7G
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$13.5 / 个
查看数据手册 →10M04DCF256A7G 最大额定值与电气特性
| Series | MAX 10 |
| Logic Elements (LE) | 4,000 |
| Maximum User I/O | 178 |
| Embedded Memory (M9K) | 193,536 bits |
| Total RAM | 1.5 Mbit |
| User Flash Memory (UFM) | 16 Kbit |
| Process Technology | 55 nm |
| Core Voltage | 1.2 V |
| 封装 | 256-LBGA (FBGA) |
| 安装类型 | Surface Mount |
| 工作温度 | -40C to +125C (Industrial) |
| Configuration Memory | Internal dual-configuration flash (instant-on) |
| Integrated ADC | 12-bit, 1 MSPS |
| RoHS 状态 | Compliant |
10M04DCF256A7G 256-lbga (fbga) 引脚配置指南
10M04DCF256A7G（256-lbga (fbga) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： 10M04DCF256A7G.
请参阅 数据手册 以查看完整引脚配置。
典型应用
10M04DCF256A7G 适用于 7 应用s: Industrial Control and I/O Expansion, Motor Control and Drive Interfaces, Portable Test and Measurement, Automotive Infotainment and Body Controllers, Video Processing Bridges and Format Conversion, Consumer Electronics Custom Logic, Communication Protocol Bridging.
Industrial Control and I/O Expansion
The 10M04DCF256A7G suits industrial PLC and I/O expansion modules where deterministic logic and 178 GPIO enable multi-protocol interfacing. The MAX 10's instant-on dual-configuration flash eliminates boot delay, critical for factory automation requiring sub-100ms power-up. Integrated 12-bit ADC supports sensor signal conditioning, while 55nm process ensures low power dissipation under continuous industrial operation. Compared to discrete MCU + CPLD designs, the 10M04 consolidates glue logic, state machines, and protocol bridging (RS-485, CAN, SPI, I2C) into a single 256-FBGA device, reducing BOM and PCB area.
推荐
Motor Control and Drive Interfaces
The 10M04DCF256A7G's 4K logic elements and 178 I/O enable field-oriented control (FOC) and PWM generation for 3-phase motor drives up to several kW. Hardware multipliers and DSP blocks accelerate Park/Clarke transforms, while 1.5 Mbit embedded RAM stores lookup tables and filter coefficients. The integrated ADC samples current and voltage feedback synchronously to PWM, reducing latency versus external ADC chains. Industrial temperature grade (-40C to +125C) and 256-FBGA thermal performance support enclosed drive enclosures with forced-air cooling.
推荐
Portable Test and Measurement
The 10M04DCF256A7G is well-suited for handheld oscilloscopes, logic analyzers, and portable data acquisition systems. Its 12-bit integrated ADC samples at 1 MSPS for mid-bandwidth signal capture, while 4K logic elements implement triggering, protocol decoding (I2C/SPI/UART), and display drivers. Single 3.3V supply operation with internal voltage regulation simplifies power tree design. The 256-FBGA package offers 178 I/O for multi-channel front-end multiplexing, and instant-on flash configuration reduces battery drain during standby.
推荐
Automotive Infotainment and Body Controllers
The 10M04DCF256A7G's industrial temperature range and 178 GPIO enable body control modules, lighting controllers, and infotainment I/O bridging in automotive designs. MAX 10 non-volatile flash supports OTA (over-the-air) firmware updates with design rollback capability, critical for vehicle recall mitigation. The integrated ADC monitors battery voltage, temperature, and illumination sensors directly. Note: this part is industrial-grade; AEC-Q100 qualified variants in the MAX 10 family should be selected for safety-critical automotive applications.
推荐
Video Processing Bridges and Format Conversion
The 10M04DCF256A7G provides LVDS, CMOS, and DDR memory interfaces for video format conversion (RGB to MIPI, HDMI to LVDS) in display panels and embedded vision systems. With 1.5 Mbit embedded block RAM, the device buffers video frames while 4K logic elements implement scaling, color space conversion, and timing generation. The 256-FBGA package supports the high pin count required for parallel video buses, and internal flash stores default boot images for instant-on display initialization.
推荐
Consumer Electronics Custom Logic
The 10M04DCF256A7G integrates custom user interfaces, LED matrix driving, and peripheral glue logic in consumer products like smart appliances, gaming peripherals, and home audio. The 12-bit ADC reads capacitive touch sensors and analog control knobs, while PWM outputs drive LED dimming at up to hundreds of kHz. Instant-on flash configuration enables immediate user response at power-up, a UX advantage over MCU boot sequences. The 256-FBGA and -40C to +125C rating suit thermally constrained consumer enclosures.
推荐
Communication Protocol Bridging
The 10M04DCF256A7G bridges legacy and modern serial interfaces (UART, SPI, I2C, CAN, USB, Ethernet) in embedded gateways. Its 178 GPIO accommodate multiple parallel protocol buses, while 4K logic elements implement protocol stack layers and timing-critical state machines. Dual-configuration flash allows field upgrades of bridge firmware without external memory, and the 55nm process ensures low standby power for always-on IoT edge devices. Industrial temperature grade supports outdoor and industrial installations.
推荐
推荐产品汇总
工程参考数据： 10M04DCF256A7G ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | 10M04DAF256A7G | 10M04DAF256C7G | 10M04DCF256C8G |
|---|---|---|---|---|
| Package | 256-LBGA (F256) | 256-LBGA (F256) - same | 256-LBGA (F256) - same | 256-LBGA (F256) - same |
| Brand | Intel | Intel - same | Intel - same | Intel - same |
| Logic Elements | 4,000 | 4,000 | 4,000 | 4,000 |
| Maximum User I/O | 178 | 178 | 178 | 178 |
| Embedded Memory (M9K) | 193,536 bits | 193,536 bits | 193,536 bits | 193,536 bits |
| Speed Grade | A7 (standard) | A7 (standard) | C7 (commercial) | C8 (commercial) |
| Operating Temperature | -40C to +125C (Industrial) | -40C to +125C (Industrial) | 0C to +85C (Commercial) | 0C to +85C (Commercial) |
| Integrated ADC | 12-bit, 1 MSPS | 12-bit, 1 MSPS | 12-bit, 1 MSPS | 12-bit, 1 MSPS |
关键差异点
- Internal dual-configuration flash eliminates external boot PROM （对比 10M04DAF256A7G)
- Industrial temperature grade for harsh environments （对比 10M04DCF256C8G)
- Integrated 12-bit ADC eliminates external sampling ICs （对比 Lattice MachXO2)
设计说明
The 256-FBGA package requires the central exposed pad to be soldered to a PCB ground plane for thermal dissipation. Estimated: at typical 1.2V core and 100mA active current, power dissipation is approximately 120mW, well within passive cooling limits. For continuous high-utilization designs (above 80% LE and DSP usage), provide at least 4 thermal vias under the exposed pad to a 2oz copper inner ground layer to keep junction temperature below 100C in enclosed industrial enclosures.
Route differential pairs (LVDS, DDR) with 100 ohm differential impedance and length-matched within 150 mils for signal integrity. Place decoupling capacitors (100nF + 10uF bulk) within 100 mils of each power pin. For MAX 10 devices, separate analog AVDD and digital VCCINT supplies with ferrite beads to prevent ADC noise coupling. According to the MAX 10 hardware design guidelines, JTAG pins (TCK, TMS, TDI, TDO) require 4.7k pull-ups on TCK and TMS for reliable configuration.
Do not confuse the 10M04DCF256A7G (industrial, A7 speed) with the 10M04DCF256C8G (commercial, C8 speed) when sourcing for industrial applications - the C8 variant lacks the -40C to +125C rating. Configuration mode (AS, PS, JTAG) must be set via MSEL pins at power-up; incorrect MSEL strapping causes silent configuration failure. The dual-configuration flash requires Quartus Prime conversion to .pof format - .sof files only program SRAM and are lost at power-down.
Place the 256-FBGA on the top side of the PCB with a 4-layer stack-up (signal-ground-power-signal) for optimal signal integrity. Use microvia or via-in-pad technology for inner-row balls to route out from the dense 1.0mm pitch array. Per Intel's MAX 10 layout guidelines, keep all high-speed traces on the top layer directly above a continuous ground plane to minimize return path inductance.
合规信息
RoHS compliant per Altera/Intel product page. Industrial temperature grade (-40C to +125C) but NOT AEC-Q100 qualified; for automotive safety-critical applications use MAX 10 AEC-Q100 variants. Halogen-free status not explicitly stated in verified data.
