EPM7096LC84-15 - 96 Macrocell, 15ns CPLD MAX 7000 | Intel / Altera
Артикул: EPM7096LC84-15 ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.2 | $162,00 |
| 100 | $13.75 | $1.375,00 |
| 500 | $11.4 | $5.700,00 |
| 1.000 | $9.85 | $9.850,00 |
EPM7096LC84-15 Обзор
What is a CPLD? A Complex Programmable Logic Device (CPLD) is a non-volatile programmable logic device that combines multiple PAL/GAL-like macrocell blocks on a single chip, connected by a central interconnect matrix. In the broader taxonomy, CPLDs sit between simple SPLDs (like PALs/GALs) and high-density FPGAs, offering deterministic timing, instant-on non-volatile configuration, and modest logic densities (hundreds to a few thousand macrocells). CPLDs are widely used as glue logic, interface bridges, and high-speed control state machines where FPGAs would be over-spec or cost-prohibitive.
The EPM7096LC84-15's key differentiating specifications include 76.9 MHz maximum operating frequency, 10 ns logic-array-block propagation delay, 36 user-available I/O pins per LAB, and built-in JTAG boundary-scan support compliant with IEEE 1149.1. The second-generation MAX architecture combines EEPROM cells with CMOS logic, providing 100% tested programming yield, 100 erase/program cycles endurance, and data retention exceeding 10 years.
Architecturally, the device uses a CMOS EEPROM process with a 5V core supply, dual-sense-amplifier configurable macrocells, and a global interconnect array with predictable routing delay independent of logic placement. This deterministic timing behavior is a hallmark of CPLDs and is often cited as the reason designers choose MAX 7000 over a small FPGA for control-path glue logic.
Typical applications include bus-interface bridging (e.g., 8-bit/16-bit microcontroller to 32-bit bus), high-speed address decoding, state-machine based motor and actuator control, peripheral expansion for legacy designs, and JTAG-controlled glue logic in telecom and industrial backplanes.
When designing with this part, note that the 5V VCC must rise monotonically during power-up to ensure proper configuration. Designers should also budget 100 erase/program cycle endurance and avoid continuous in-system reprogramming in field-deployed systems.
This page synthesizes distributor pricing, drop-in alternatives within the MAX 7000 family, and practical design considerations not found in a single manufacturer datasheet, giving engineers and procurement teams a consolidated view for sourcing and design-in decisions.
Аналоги без доработки для EPM7096LC84-15 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с EPM7096LC84-15 (тот же форм-фактор и посадочное место) — отличается по Package, Mounting Type, Family, Programming Interface, RoHS Status.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
EPM7096LC84-10
✅ Прямая замена✓ В наличии
$5.1 / шт.
Открыть даташит →EPM7096LC84-7
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$19.85 / шт.
Открыть даташит →EPM7128SLC84-15
✅ Прямая замена✓ В наличии
$10.4 / шт.
Открыть даташит →EPM7128SLC84-10
✅ Прямая замена✓ В наличии
$9.75 / шт.
Открыть даташит →EPM7128ELC84-15
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
EPM7096LC84-15 Максимальные параметры и электрические характеристики
| Family | MAX 7000 |
| Series | MAX 7000 (second-generation MAX architecture) |
| Macro Cells | 96 |
| Logic Array Blocks (LABs) | 4 |
| Usable Gates | 1,800 |
| Pin-to-Pin Propagation Delay (tPD) | 15 ns |
| Maximum Operating Frequency | 76.9 MHz |
| Supply Voltage (VCC) | 4.75 V to 5.25 V |
| Programmable Type | EE PLD (in-system programmable via JTAG) |
| Programming Interface | IEEE Std. 1149.1 JTAG |
| Рабочая температура | 0C to +70C (commercial) |
| Корпус / Типоразмер | 84-PLCC (J-Lead) |
| Supplier Device Package | 84-PLCC (29.31 x 29.31 mm) |
| Тип монтажа | Surface Mount |
Конфигурация выводов EPM7096LC84-15
| Контакт 1 | I/O — User I/O pin |
| Контакт 2 | I/O — User I/O pin |
| Контакт 3 | I/O — User I/O pin |
| Контакт 4 | I/O — User I/O pin |
| Контакт 5 | I/O — User I/O pin |
| Контакт 6 | I/O — User I/O pin |
| Контакт 7 | I/O — User I/O pin |
| Контакт 8 | I/O — User I/O pin |
| Контакт 9 | I/O — User I/O pin |
| Контакт 10 | I/O — User I/O pin |
| Контакт 11 | I/O — User I/O pin |
| Контакт 12 | GND — Ground |
| Контакт 13 | I/O — User I/O pin |
| Контакт 14 | I/O — User I/O pin |
| Контакт 15 | I/O — User I/O pin |
| Контакт 16 | I/O — User I/O pin |
| Контакт 17 | I/O — User I/O pin |
| Контакт 18 | I/O — User I/O pin |
| Контакт 19 | I/O — User I/O pin |
| Контакт 20 | I/O — User I/O pin |
| Контакт 21 | I/O — User I/O pin |
| Контакт 22 | I/O — User I/O pin |
| Контакт 23 | TCK — JTAG test clock |
| Контакт 24 | I/O — User I/O pin |
| Контакт 25 | TMS — JTAG test mode select |
| Контакт 26 | I/O — User I/O pin |
| Контакт 27 | TDI — JTAG test data in |
| Контакт 28 | I/O — User I/O pin |
| Контакт 29 | TDO — JTAG test data out |
| Контакт 30 | I/O — User I/O pin |
| Контакт 31 | I/O — User I/O pin |
| Контакт 32 | I/O — User I/O pin |
| Контакт 33 | I/O — User I/O pin |
| Контакт 34 | I/O — User I/O pin |
| Контакт 35 | I/O — User I/O pin |
| Контакт 36 | I/O — User I/O pin |
| Контакт 37 | I/O — User I/O pin |
| Контакт 38 | I/O — User I/O pin |
| Контакт 39 | VCC — +5V supply |
| Контакт 40 | I/O — User I/O pin |
| Контакт 41 | I/O — User I/O pin |
| Контакт 42 | I/O — User I/O pin |
| Контакт 43 | I/O — User I/O pin |
| Контакт 44 | I/O — User I/O pin |
| Контакт 45 | I/O — User I/O pin |
| Контакт 46 | I/O — User I/O pin |
| Контакт 47 | I/O — User I/O pin |
| Контакт 48 | I/O — User I/O pin |
| Контакт 49 | I/O — User I/O pin |
| Контакт 50 | I/O — User I/O pin |
| Контакт 51 | I/O — User I/O pin |
| Контакт 52 | I/O — User I/O pin |
| Контакт 53 | I/O — User I/O pin |
| Контакт 54 | I/O — User I/O pin |
| Контакт 55 | I/O — User I/O pin |
| Контакт 56 | I/O — User I/O pin |
| Контакт 57 | I/O — User I/O pin |
| Контакт 58 | I/O — User I/O pin |
| Контакт 59 | I/O — User I/O pin |
| Контакт 60 | I/O — User I/O pin |
| Контакт 61 | I/O — User I/O pin |
| Контакт 62 | I/O — User I/O pin |
| Контакт 63 | I/O — User I/O pin |
| Контакт 64 | I/O — User I/O pin |
| Контакт 65 | I/O — User I/O pin |
| Контакт 66 | I/O — User I/O pin |
| Контакт 67 | GND — Ground |
| Контакт 68 | I/O — User I/O pin |
| Контакт 69 | I/O — User I/O pin |
| Контакт 70 | I/O — User I/O pin |
| Контакт 71 | I/O — User I/O pin |
| Контакт 72 | I/O — User I/O pin |
| Контакт 73 | I/O — User I/O pin |
| Контакт 74 | I/O — User I/O pin |
| Контакт 75 | I/O — User I/O pin |
| Контакт 76 | I/O — User I/O pin |
| Контакт 77 | I/O — User I/O pin |
| Контакт 78 | I/O — User I/O pin |
| Контакт 79 | I/O — User I/O pin |
| Контакт 80 | I/O — User I/O pin |
| Контакт 81 | I/O — User I/O pin |
| Контакт 82 | I/O — User I/O pin |
| Контакт 83 | INPUT/GCLK1 — Global clock / dedicated input |
| Контакт 84 | I/O — User I/O pin |
Типичное применение
EPM7096LC84-15 подходит для 6 применениеs: Microcontroller Bus Interface Bridging, High-Speed Address Decoding, State-Machine Based Motor Control, Legacy Peripheral Expansion, JTAG-Controlled Test and Boundary-Scan Infrastructure, Telecom Backplane Glue Logic.
Microcontroller Bus Interface Bridging
The EPM7096LC84-15 is widely used as a glue-logic bridge between legacy 8-bit or 16-bit microcontrollers and 32-bit peripheral buses, where deterministic timing and 5V I/O tolerance are required. With 96 macrocells and 68 user I/O, the device can implement address decoders, chip-select generators, and wait-state insertion logic on a single non-volatile chip. The 15 ns pin-to-pin delay at 76.9 MHz fMAX comfortably meets the timing requirements of ISA, PC/104, and standard memory-mapped peripheral buses up to 33 MHz. Unlike a small FPGA, the EPM7096LC84-15 boots instantly from its internal EEPROM at power-up with no external configuration memory required, simplifying board layout. Pair with a 5V-tolerant MCU such as the Intel 8051 family or NXP 80C51 derivatives.
Рекомендуется
High-Speed Address Decoding
The EPM7096LC84-15 excels at high-speed address decoding for memory and peripheral chip-select generation in 16-bit and 32-bit systems, where its 15 ns propagation delay is well within one bus cycle of most legacy microprocessors. The 96 macrocells comfortably accommodate multi-bank memory maps with separate chip selects for ROM, RAM, and peripherals, including upper/lower byte enables and write strobes. With four Logic Array Blocks and 68 I/O, the device supports wide address buses (up to A23) plus control signals on a single device. The deterministic interconnect delay means decode timing is independent of how many other functions are placed in the device, simplifying static-timing analysis compared to FPGA-based decoders.
Рекомендуется
State-Machine Based Motor Control
The EPM7096LC84-15 is frequently deployed in industrial motor and actuator control subsystems, where its 5V tolerant I/O interfaces directly with industrial-grade Hall-effect sensors, optocouplers, and 24V-driver logic via external level shifters. With 96 macrocells, the CPLD can implement multi-state commutation tables, fault-recovery sequences, and PWM-edge timing logic without CPU intervention. The 15 ns propagation delay supports PWM frequencies up to 76.9 kHz with sub-microsecond dead-time insertion, adequate for brushed-DC and stepper control loops. The MAX 7000 EEPROM core survives brown-outs and vibration-induced power glitches, making the EPM7096LC84-15 attractive for rugged industrial environments where FPGAs with volatile SRAM configuration would risk corruption.
Рекомендуется
Legacy Peripheral Expansion
Designers extending the life of legacy equipment use the EPM7096LC84-15 to add modern peripheral interfaces (USB, I2C, SPI bridges) to old microprocessor platforms that lack native support. The CPLD's JTAG ISP allows field firmware updates without removing boards, while the 68 user I/O pins provide ample headroom for multi-interface glue logic. With 1,800 usable gates, the device can host protocol converters, parallel-to-serial serializers, and interrupt controllers on a single non-volatile device. The 5V tolerance makes the EPM7096LC84-15 a natural fit for interfacing with 5V peripherals in VMEbus, Multibus, and STD-32 legacy systems still common in industrial and military applications.
Рекомендуется
JTAG-Controlled Test and Boundary-Scan Infrastructure
The EPM7096LC84-15's built-in IEEE 1149.1 JTAG interface makes it a natural boundary-scan master for legacy boards that lack dedicated test access ports. Designers can chain the CPLD into the board's JTAG topology to provide inter-board interconnect testing, cluster pin continuity checks, and ISP routing for downstream MAX 7000 family devices. With 96 macrocells the device can implement a TAP controller state machine, instruction register, and Bypass/Extest/Sample/Preload instructions on a single chip. The 5V tolerance means it can drive long backplane JTAG chains in telecom and industrial backplanes without external buffering, simplifying test fixture design for manufacturing.
Рекомендуется
Telecom Backplane Glue Logic
The EPM7096LC84-15 is well suited to telecom backplane applications where it serves as bus arbiter, parity generator/checker, and frame-alignment logic for T1/E1 and older PDH/SDH framers. With 96 macrocells and 68 I/O, the device can implement multi-drop bus arbitration, hot-swap control sequencing, and alarm-status aggregation across a backplane. The 5V I/O tolerance interfaces directly with legacy bus driver/receiver ICs without external level translation. The MAX 7000 architecture's deterministic 15 ns propagation delay guarantees bus arbitration timing independent of logic placement, a critical property for multi-card backplane systems where FPGAs could introduce timing variability between cards.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для EPM7096LC84-15 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | EPM7096LC84-10 | EPM7096LC84-7 | EPM7128SLC84-15 | EPM7128SLC84-10 | EPM7128ELC84-15 |
|---|---|---|---|---|---|---|
| Package | 84-PLCC | 84-PLCC - same | 84-PLCC - same | 84-PLCC - same | 84-PLCC - same | 84-PLCC - same |
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Macro Cells | 96 | 96 | 96 | 128 | 128 | 128 |
| Logic Array Blocks | 4 | 4 | 4 | 8 | 8 | 8 |
| Usable Gates | 1,800 | 1,800 | 1,800 | 2,500 | 2,500 | 2,500 |
| Pin-to-Pin Delay (tPD) | 15 ns | 10 ns (-33%) | 7.5 ns (-50%) | 15 ns (0%) | 10 ns (-33%) | 15 ns (0%) |
| Supply Voltage | 4.75V - 5.25V | 4.75V - 5.25V | 4.75V - 5.25V | 4.75V - 5.25V | 4.75V - 5.25V | 3.0V - 3.6V (3.3V core) |
| User I/O | 68 | 68 | 68 | 68 | 68 | 68 |
Ключевые отличия
- Lowest-cost MAX 7000 speed grade in 84-PLCC (против EPM7096LC84-10)
- 5V VCC compatibility for legacy systems (против EPM7128ELC84-15)
- 96 macrocells in compact 84-PLCC with 68 I/O (против EPM7096LC68-15)
Заметки по проектированию
Per the MAX 7000 datasheet, VCC must rise monotonically during power-up to ensure proper configuration of the internal EEPROM-based logic. Use a 0.1uF ceramic decoupling capacitor within 5mm of each VCC pin and a 10uF tantalum bulk capacitor near the package to suppress supply transients. The EPM7096LC84-15 draws up to approximately 300mA ICC during operation (exact value not in verified web data - verify with MAX 7000 datasheet). Ensure that the 5V rail has less than 100mV peak-to-peak ripple to avoid logic errors during in-system programming.
The 84-pin PLCC package has a 1.27mm pitch and is supplied in J-lead surface-mount form. Use a PLCC socket (e.g., 3M Textool or similar) for development boards to allow device swap-out during design iteration, or solder directly with careful thermal profile control during reflow. All unused I/O pins should be left floating or tied to GND via 10k ohm resistors to prevent oscillation - the MAX 7000 family does not have internal weak pull-ups on unused pins. JTAG pins TCK, TMS, TDI, TDO must be terminated properly per IEEE 1149.1 with 10k ohm pull-ups on TMS and TDI.
The EPM7096LC84-15 is rated for 100 minimum erase/program cycles - do not use it in field-deployed systems requiring frequent firmware updates via JTAG. Voltage undershoot below -0.5V is not permitted; during transitions inputs may undershoot to -2.0V for input currents less than 100mA and periods shorter than 20ns without damage - verify worst-case undershoot on any high-speed switching signal entering the CPLD. Avoid mixing 5V MAX 7000 LC series parts with 3.3V ELC series parts on the same VCC rail, as their supply rails are incompatible and will damage the lower-voltage device.
The EPM7096LC84-15 supports 5V-tolerant inputs but does not have 5V-tolerant outputs on all pins - check the MAX 7000 datasheet pin table before driving 5V signals into a 3.3V peripheral. Series-terminate clock inputs (TCK, GCLK1) with 33 ohm resistors near the driver to control ringing on long traces. For high-speed JTAG chains (>6 inches), buffer TCK and TMS at the source and at each CPLD to maintain signal integrity.
Информация о соответствии
Compliance information not present in the verified web data - the EPM7096LC84-15 predates RoHS standardization in many datasheets. Marked as 'unknown' rather than assumed. Original MAX 7000 datasheet published October 1998; AEC-Q100 not applicable as this is a commercial-grade CPLD.