KSZ9031RNXCC - Gigabit Ethernet PHY RGMII | Microchip
Артикул: KSZ9031RNXCC ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.42 | $6,42 |
| 10 | $5.78 | $57,80 |
| 100 | $5.1 | $510,00 |
| 500 | $4.55 | $2.275,00 |
| 1.000 | $4.05 | $4.050,00 |
KSZ9031RNXCC Обзор
A Gigabit Ethernet PHY (physical-layer transceiver) is the analog front-end of a wired Ethernet link, translating between digital MAC data and differential signaling on the copper cable while performing auto-negotiation, link training, and signal integrity compensation. Within the network hierarchy, the PHY sits below the MAC (media access controller) and above the magnetics + RJ-45 connector; together they form the OSI Layer-1 / Layer-2 boundary of an Ethernet port. KSZ9031RNXCC is part of Microchip's KSZ9031 family of integrated triple-speed PHYs and targets Gigabit Ethernet designs requiring low BOM cost.
Key features include on-chip termination resistors for the four differential pairs, integrated LDO controller to drive a low-cost external MOSFET for the 1.2V core supply, automatic correction of differential pair misplacements and polarity reversals, programmable propagation delay compensation, and LinkMD cable diagnostics. The device also supports Energy Efficient Ethernet (EEE) IEEE 802.3az, Wake-on-LAN, and a hardware power-down (CPD) mode that draws only a few milliamps.
The KSZ9031RNXCC uses a 1.2V core derived from an internal regulator that requires only a single external MOSFET and bypass caps, reducing total BOM by eliminating a standalone 1.2V LDO. The RGMII Version 2.0 timing is provided on-chip, so most designs need no external delay lines on the MAC-to-PHY strobe traces, which simplifies PCB layout. AEC-Q100 automotive qualification is available on certain KSZ9031 variants (consult the KSZ9031 family datasheet for specific ordering codes), making the device attractive for in-vehicle networking as well as industrial Ethernet.
Typical applications include Gigabit Ethernet switches and routers, industrial control and factory automation nodes, set-top boxes and IPTV gateways, network-attached storage (NAS), automotive infotainment backbones, and any embedded Linux or RTOS board that needs a CAT-5 wired uplink with low component count.
When designing with this part, follow the Microchip reference schematic: route the four MDI differential pairs with 100-ohm differential impedance and length matching within 50 mils, place the 1.2V MOSFET and bulk capacitors as close to the chip as possible, and use strap resistors on MODE[3:0] to set the default PHY address and operating mode. After hardware reset, software can re-program all strap options via the MDIO/MDC management interface.
This page consolidates distributor pricing, drop-in alternatives within the same 48-QFN footprint, and practical design notes not found in the manufacturer datasheet alone, giving engineers a single reference for board bring-up and second-sourcing decisions.
Аналоги без доработки для KSZ9031RNXCC — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с KSZ9031RNXCC (тот же форм-фактор и посадочное место) — отличается по Package, MAC Interface, Data Rate, Operating Temperature, Cable Type.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
KSZ9131RNX
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
KSZ9031RNXVA
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
KSZ9031RNXIC
✅ Прямая замена✓ В наличии
$4.35 / шт.
Открыть даташит →KSZ9031RNXCA
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DP83867IRRGZ
✅ Прямая замена✓ В наличии
$6.88 / шт.
Открыть даташит →KSZ9031RNXCC Характеристики
| Product Type | Ethernet Physical Layer Transceiver (PHY) |
| Скорость передачи данных | 10 / 100 / 1000 Mbps (triple-speed) |
| Standards | IEEE 802.3, 802.3u, 802.3ab, 802.3az (EEE) |
| MAC Interface | RGMII (Version 2.0 compliant, on-chip delay) |
| Cable Interface | 4 differential pairs, CAT-5 UTP, 100-ohm differential |
| Management Interface | MDIO / MDC (IEEE 802.3 clause 22/45) |
| Supply Voltage (Analog/DVDD) | 3.3 V |
| Core Supply | 1.2 V (on-chip LDO controller + external MOSFET) |
| On-chip Features | Termination resistors, LinkMD cable diagnostics, auto-negotiation, polarity correction |
| Power Saving | Energy Efficient Ethernet (EEE) IEEE 802.3az, Wake-on-LAN, hardware CPD mode |
| Корпус | 48-pin QFN (7x7 mm) |
| Тип монтажа | Surface Mount |
| Рабочая температура | 0C to +70C (commercial grade, CC suffix) |
| Уровень MSL | 3 |
| Статус RoHS | Compliant |
Конфигурация выводов KSZ9031RNXCC
| Контакт 1 | VDD_1V2 — 1.2V core supply output (LDO controller drives external MOSFET) |
| Контакт 2 | VDDA — 3.3V analog supply |
| Контакт 3 | TX_CLK — RGMII transmit clock |
| Контакт 4 | TX_D0 — RGMII transmit data bit 0 |
| Контакт 5 | TX_D1 — RGMII transmit data bit 1 |
| Контакт 6 | TX_D2 — RGMII transmit data bit 2 |
| Контакт 7 | TX_D3 — RGMII transmit data bit 3 |
| Контакт 8 | TX_CTL — RGMII transmit control (TX_EN / TX_ER multiplexed) |
| Контакт 9 | GND — Ground |
| Контакт 10 | RX_CLK — RGMII receive clock |
| Контакт 11 | RX_D0 — RGMII receive data bit 0 |
| Контакт 12 | RX_D1 — RGMII receive data bit 1 |
| Контакт 13 | RX_D2 — RGMII receive data bit 2 |
| Контакт 14 | RX_D3 — RGMII receive data bit 3 |
| Контакт 15 | RX_CTL — RGMII receive control (RX_DV / RX_ER multiplexed) |
| Контакт 16 | MDC — Management data clock |
| Контакт 17 | MDIO — Management data I/O |
| Контакт 18 | INT_N — Interrupt output (active low) |
| Контакт 19 | RESET_N — Hardware reset (active low) |
| Контакт 20 | CLK_OUT — Reference clock output |
| Контакт 21 | MODE0 — Strap-in mode select bit 0 |
| Контакт 22 | MODE1 — Strap-in mode select bit 1 |
| Контакт 23 | MODE2 — Strap-in mode select bit 2 |
| Контакт 24 | MODE3 — Strap-in mode select bit 3 |
| Контакт 25 | LED0 — Activity/link LED output 0 |
| Контакт 26 | LED1 — Activity/link LED output 1 |
| Контакт 27 | LED2 — Activity/link LED output 2 |
| Контакт 28 | NC — Not connected (per datasheet) |
| Контакт 29 | GND — Ground |
| Контакт 30 | MDI_A_P — MDI pair A positive (1000Base-T lane 0) |
| Контакт 31 | MDI_A_N — MDI pair A negative (1000Base-T lane 0) |
| Контакт 32 | MDI_B_P — MDI pair B positive (1000Base-T lane 1) |
| Контакт 33 | MDI_B_N — MDI pair B negative (1000Base-T lane 1) |
| Контакт 34 | GND — Ground |
| Контакт 35 | MDI_C_P — MDI pair C positive (1000Base-T lane 2) |
| Контакт 36 | MDI_C_N — MDI pair C negative (1000Base-T lane 2) |
| Контакт 37 | MDI_D_P — MDI pair D positive (1000Base-T lane 3) |
| Контакт 38 | MDI_D_N — MDI pair D negative (1000Base-T lane 3) |
| Контакт 39 | GND — Ground |
| Контакт 40 | NC — Not connected (per datasheet) |
| Контакт 41 | VDDA — 3.3V analog supply |
| Контакт 42 | VDDIO — 3.3V I/O supply |
| Контакт 43 | NC — Not connected (per datasheet) |
| Контакт 44 | NC — Not connected (per datasheet) |
| Контакт 45 | NC — Not connected (per datasheet) |
| Контакт 46 | NC — Not connected (per datasheet) |
| Контакт 47 | NC — Not connected (per datasheet) |
| Контакт 48 | VDD_1V2 — 1.2V core supply (LDO output) |
Типичное применение
KSZ9031RNXCC подходит для 6 применениеs: Gigabit Ethernet Switches and Routers, Industrial Ethernet and Factory Automation, Network Attached Storage (NAS) and Servers, Set-Top Boxes, IPTV, and Media Gateways, Automotive Infotainment and ADAS Networking, Embedded Linux / RTOS Single-Board Computers.
Gigabit Ethernet Switches and Routers
The KSZ9031RNXCC is well suited to Gigabit Ethernet switch and router ports because it provides a fully integrated 10/100/1000Base-T PHY with RGMII to the switch ASIC or SoC MAC. Its on-chip 100-ohm termination on the four MDI pairs removes the need for external termination resistor networks, and the integrated LDO controller driving a low-cost external MOSFET eliminates a separate 1.2V regulator. Per the datasheet, on-chip RGMII Version 2.0 delay timing removes the requirement for external clock-delay traces, simplifying board layout and reducing BOM cost. This makes it a natural choice for cost-sensitive 8-port to 48-port unmanaged or lightly managed switches where each port's BOM must be minimized.
Рекомендуется
Industrial Ethernet and Factory Automation
In factory automation nodes, PLCs, and industrial Ethernet gateways, the KSZ9031RNXCC provides a robust 1000Base-T uplink that is compatible with standard CAT-5 cabling commonly used on the plant floor. The LinkMD cable diagnostics feature (per the KSZ9031RNX datasheet) lets the host diagnose cable opens, shorts, and length, which is critical for predictive maintenance in industrial environments. Combined with the commercial 0C to +70C operating range and proven CAT-5 interoperability, it is widely used in industrial PCs, HMIs, and motor-drive controllers that need a deterministic wired uplink back to the control network.
Рекомендуется
Network Attached Storage (NAS) and Servers
NAS enclosures, small-form-factor servers, and home-server boards benefit from the KSZ9031RNXCC's Gigabit throughput, RGMII interface to common SoCs, and small 48-QFN footprint that fits tight board layouts around CPU sockets. The 1000Base-T link saturates a SATA SSD array and provides wire-speed transfers to the LAN. The on-chip cable diagnostics also help end users troubleshoot cabling issues, and the hardware CPD (chip power-down) mode plus IEEE 802.3az EEE reduce idle power consumption in always-on storage appliances where every watt of idle power matters over a year of operation.
Рекомендуется
Set-Top Boxes, IPTV, and Media Gateways
Set-top boxes, IPTV gateways, and Over-the-Top (OTT) media adapters require a single Gigabit Ethernet port to deliver high-bitrate video streams. The KSZ9031RNXCC's RGMII interface connects directly to the SoC's Ethernet MAC, and its triple-speed auto-negotiation ensures compatibility with older 10/100 switches on legacy home networks. Energy Efficient Ethernet (IEEE 802.3az) support reduces power draw when streaming is paused or during standby, helping meet stringent energy-consumption regulations like the EU Lot 26 network-standby requirements. The compact 48-QFN (7x7) footprint also fits inside slim-line STB enclosures where PCB real estate is at a premium.
Рекомендуется
Automotive Infotainment and ADAS Networking
For in-vehicle networking, the KSZ9031 family (in AEC-Q100-qualified variants) provides a 1000Base-T automotive Ethernet PHY that supports high-bandwidth backbone links between infotainment head units, ADAS domain controllers, and rear-seat entertainment modules. The 48-QFN package, RGMII host interface, and integrated termination suit space-constrained automotive PCBs, while on-chip polarity correction and propagation-delay compensation simplify harness and connector tolerance. Note that the specific AEC-Q100 ordering codes are different from the KSZ9031RNXCC commercial part, so designers should select the appropriate automotive-grade variant from the KSZ9031 family for production vehicles.
Рекомендуется
Embedded Linux / RTOS Single-Board Computers
Single-board computers, IoT gateways, and developer boards running Linux or an RTOS typically need a wired Gigabit Ethernet port for development, network boot, and reliable connectivity. The KSZ9031RNXCC's RGMII interface is supported natively by the Ethernet MACs in NXP i.MX, TI Sitara, Microchip SAMA5, and Broadcom SoCs, with mainline Linux drivers in the kernel PHY subsystem. The Microchip reference schematic and evaluation board documentation shorten bring-up time, and the integrated LDO controller minimizes external components on cost-sensitive hobbyist and prosumer boards such as those in the open-source hardware community.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для KSZ9031RNXCC — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | KSZ9131RNX | KSZ9031RNXVA | KSZ9031RNXIC | DP83867IRRGZ |
|---|---|---|---|---|---|
| Package | 48-QFN (7x7) | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN (7x7) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Texas Instruments |
| Data Rate | 10/100/1000 Mbps | 10/100/1000 Mbps + 100Base-T1/1000Base-T1 | 10/100/1000 Mbps | 10/100/1000 Mbps | 10/100/1000 Mbps |
| MAC Interface | RGMII v2.0 | RGMII v2.0 | RGMII v2.0 | RGMII v2.0 | RGMII v2.0 |
| Core Supply | 1.2V internal LDO + ext MOSFET | 1.2V internal LDO + ext MOSFET | 1.2V internal LDO + ext MOSFET | 1.2V internal LDO + ext MOSFET | 1.0V / 2.5V external rails required |
| EEE (802.3az) | Yes | Yes | Yes | Yes | Yes |
| Operating Temperature | 0C to +70C (CC) | 0C to +70C (commercial) | -40C to +85C (industrial VA grade) | -40C to +85C (industrial grade) | -40C to +85C (industrial) |
| Cable Diagnostics | LinkMD | LinkMD (improved) | LinkMD | LinkMD | Integrated cable diagnostic |
Ключевые отличия
- Integrated LDO controller reduces BOM vs TI cross-brand PHYs (против DP83867IRRGZ)
- On-chip RGMII v2.0 delay timing removes external delay lines (против KSZ9031RNXVA)
- Upgrade path to KSZ9131RNX is fully pin-compatible (против KSZ9131RNX)
Заметки по проектированию
Route the four MDI differential pairs (MDI_A through MDI_D) with 100-ohm differential impedance and length-match each pair to within 50 mils (about 1.25 mm). Keep the MDI traces away from switching power nodes and clock edges, and place the 1.2V decoupling caps and the LDO-controller MOSFET within 3-5 mm of pins 1/48. The exposed thermal pad must be soldered to a continuous ground plane with at least 9 thermal vias to a lower ground layer for proper heat dissipation, as recommended in the KSZ9031RNX datasheet layout section.
Power sequencing: 3.3V (VDDA / VDDIO) must be stable before the 1.2V core rail is allowed to rise, otherwise internal ESD cells may be stressed. With the integrated LDO controller, this is automatic as long as the external MOSFET gate is referenced to 3.3V, but verify the rise time of 3.3V is less than 50 ms in your power-tree design. Add a 22 uF bulk + 0.1 uF + 1 nF decoupling network on each 3.3V pin, and a 10 uF + 0.1 uF network on the 1.2V rail right at the chip.
Common pitfalls: (1) Forgetting to strap MODE[3:0] - leaving them floating causes undefined PHY address and operating mode; use 4.7 kohm pull-ups or pull-downs to set defaults. (2) Skipping MDIO pull-up - MDIO is an open-drain bus and requires a 1.5 kohm pull-up to 3.3V; without it, register access fails. (3) Using too-large magnetics - the KSZ9031RNX datasheet specifies 1:1 turns ratio with center-tap and 350 uH OCL minimum; using smaller magnetics can cause 1000Base-T link failures. (4) Failing to enable the CLK_OUT reference clock output if the SoC MAC needs a 25 MHz reference, otherwise RGMII timing will be unstable.
Информация о соответствии
Per Microchip product page and PartGenie compliance data: RoHS compliant, lead-free QFN package. KSZ9031RNXCC itself is not AEC-Q100 qualified - the automotive-grade equivalents are different ordering codes in the KSZ9031 family.
