M48T58-70PC1 - 64Kbit Timekeeper SRAM RTC 70ns | STMicroelectronics
Артикул: M48T58-70PC1 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $16.5 | $16,50 |
| 10 | $14.85 | $148,50 |
| 100 | $13.2 | $1.320,00 |
| 500 | $11.75 | $5.875,00 |
| 1.000 | $10.4 | $10.400,00 |
M48T58-70PC1 Обзор
A Timekeeper SRAM is a hybrid non-volatile memory device that combines the byte-wide random access of a standard SRAM with on-chip battery backup and an integrated real-time clock. It belongs to the broader family of non-volatile RAM (NVRAM) products, sitting between conventional SRAM and serial NVSRAM/FRAM in the memory hierarchy. Compared to standard SRAM, a Timekeeper eliminates external battery-management circuitry and supports BCD-coded year/month/day/date/hour/minute/second read-out.
Key features include 70 ns read/write access time, integrated lithium battery with typical 10-year data retention, automatic power-fail/write-protection circuitry, bytewide RAM-like clock access, BCD-coded year/month/day/date/hour/minute/seconds registers, frequency test output for real-time clock, and JEDEC-standard 8 K x 8 SRAM pin/function equivalence. The monolithic chip ships in a special 28-pin DIP Module (CAPHAT) that accommodates the embedded battery cell.
The architecture centers on a low-power 8K x 8 SRAM array, a 32 kHz crystal-controlled oscillator for the RTC, and a power-fail comparator that latches the CS/WE/OE write-protect signals when VCC drops below a defined threshold. The internal lithium cell then holds both the SRAM contents and the RTC registers, allowing the device to drop into any JEDEC-standard 8K x 8 SRAM socket without any WRITE-timing constraints.
Typical applications include industrial data logging, point-of-sale terminals, metering equipment, factory automation controllers, medical instruments, and any embedded system that requires both non-volatile variables and a wall-clock/calendar without an external backup battery or RTC chip. Designers use it as a one-chip substitute for SRAM + discrete RTC + supercapacitor/cell combinations.
When designing with this device, observe the standard 8K x 8 SRAM timing (address setup, CS-to-OE, write-pulse width) and route the VCC decoupling close to the supply pin. Because the lithium cell is non-replaceable in the CAPHAT package, treat the module as a sealed unit; planned end-of-life data retention after VCC removal is on the order of 10 years per the manufacturer.
This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes that go beyond the manufacturer's datasheet, supporting faster component evaluation.
Аналоги без доработки для M48T58-70PC1 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с M48T58-70PC1 (тот же форм-фактор и посадочное место) — отличается по Memory Size, Operating Temperature, Package.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
M48T58Y-70PC1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
M48T08-100PC1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
M48T02-70PC1
✅ Прямая замена✓ В наличии
$12.4 / шт.
Открыть даташит →DS1643-100+
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DS1225AD-150+
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
M48T58-70PC1 Максимальные параметры и электрические характеристики
| Product Type | Non-volatile Timekeeper SRAM with Real-Time Clock |
| Размер памяти | 64 Kbit (8 Kb x 8) |
| Memory Organization | 8 K x 8 |
| Access Time | 70 ns |
| Supply Voltage (VCC) | 4.75 V to 5.5 V |
| Рабочая температура | 0C to +70C |
| Тип интерфейса | Parallel |
| Clock/Calendar | BCD-coded year/month/day/date/hour/minute/second |
| Battery Backup | Integrated lithium cell |
| Data Retention (battery) | 10 years typical |
| Write Protection | Automatic power-fail write-protect |
| Frequency Test Output | Yes (for RTC) |
| Корпус | 28-pin DIP Module (CAPHAT), 0.600 inch (15.24 mm) |
| Тип монтажа | Through-Hole (DIP Module) |
| JEDEC SRAM Compatibility | Pin- and function-equivalent to JEDEC 8K x 8 SRAM |
| Статус RoHS | Compliant |
Конфигурация выводов M48T58-70PC1
| Контакт 1 | A7 — Address input A7 |
| Контакт 2 | A6 — Address input A6 |
| Контакт 3 | A5 — Address input A5 |
| Контакт 4 | A4 — Address input A4 |
| Контакт 5 | A3 — Address input A3 |
| Контакт 6 | A2 — Address input A2 |
| Контакт 7 | A1 — Address input A1 |
| Контакт 8 | A0 — Address input A0 |
| Контакт 9 | DQ0 — Data I/O 0 |
| Контакт 10 | DQ1 — Data I/O 1 |
| Контакт 11 | DQ2 — Data I/O 2 |
| Контакт 12 | GND — Ground |
| Контакт 13 | DQ3 — Data I/O 3 |
| Контакт 14 | DQ4 — Data I/O 4 |
| Контакт 15 | DQ5 — Data I/O 5 |
| Контакт 16 | DQ6 — Data I/O 6 |
| Контакт 17 | DQ7 — Data I/O 7 |
| Контакт 18 | /WE — Write enable (active low) |
| Контакт 19 | A11 — Address input A11 |
| Контакт 20 | /CE — Chip enable (active low) |
| Контакт 21 | A10 — Address input A10 |
| Контакт 22 | OE — Output enable (active high) |
| Контакт 23 | A9 — Address input A9 |
| Контакт 24 | A8 — Address input A8 |
| Контакт 25 | A12 — Address input A12 (NC on 8K x 8) |
| Контакт 26 | /FT — Frequency test output for RTC |
| Контакт 27 | RST — Power-on reset / RTC clear (open drain) |
| Контакт 28 | VCC — +5 V supply |
Типичное применение
M48T58-70PC1 подходит для 6 применениеs: Industrial Data Logging, Point-of-Sale Terminals, Utility Metering, Factory Automation Controllers, Medical Instrumentation, Embedded Systems with Calendar.
Industrial Data Logging
The M48T58-70PC1 fits industrial data logging because its 8 Kb x 8 non-volatile SRAM retains parameter records through power loss while the integrated RTC timestamps each event. With a 5 V supply, 70 ns access, and 10-year battery retention, it logs vibration, temperature and pressure samples in PLCs and SCADA nodes without external backup batteries. Place the device on a JEDEC 8K x 8 SRAM socket; bus timing matches standard SRAM so no special write protocol is required. Compared to a discrete SRAM + DS1338 RTC + supercapacitor, the M48T58-70PC1 reduces BOM, PCB area and reliability risk.
Рекомендуется
Point-of-Sale Terminals
The M48T58-70PC1 suits point-of-sale terminals by providing both the non-volatile transaction buffer and the wall-clock/calendar in one chip. The 70 ns access time supports fast SRAM writes during card swipe and receipt printing, while the BCD-coded year/month/day/date/hour/minute/second registers drive the on-receipt timestamp. The integrated lithium cell keeps the time and audit trail intact across unplanned power cycling of the POS register. Drop the module into a JEDEC 8K x 8 SRAM socket; no firmware changes are needed versus a discrete 6264.
Рекомендуется
Utility Metering
The M48T58-70PC1 is well suited to electricity, water and gas meters where long-term tamper-resistant data retention and accurate billing timestamps are required. The 10-year integrated lithium retention covers the typical meter calibration interval, and the 5 V supply aligns with meter power rails. The automatic power-fail write-protect prevents corrupted consumption records during brownouts. Designers wire the device exactly like a JEDEC 8K x 8 SRAM and read the BCD RTC to stamp each consumption log entry. Compared to FRAM, the Timekeeper SRAM is a lower-cost legacy solution for 8 Kb needs.
Рекомендуется
Factory Automation Controllers
The M48T58-70PC1 serves factory automation controllers that must store recipe parameters, fault logs and shift counters across 24V-to-5V power cycles. The 70 ns access time keeps SRAM cycles within typical PLC scan budgets, and the integrated RTC supplies BCD time stamps for event logs. The CAPHAT DIP Module package supports through-hole assembly on legacy PLC backplanes that already use JEDEC 8K x 8 SRAM sockets. This avoids firmware-side battery-management code that would otherwise be needed with a discrete SRAM plus external RTC design.
Рекомендуется
Medical Instrumentation
The M48T58-70PC1 fits medical instruments such as blood analyzers, infusion pumps and patient monitors where parameter retention and audit timestamps must survive power loss. The 10-year battery retention supports the typical service life of bench-top analyzers, and the 5 V 70 ns timing satisfies display-controller and DSP host bus interfaces. The CAPHAT DIP Module simplifies the medical IEC 60601-1 isolation boundary by keeping backup storage in one sealed component. The BCD RTC timestamps each measurement for FDA 21 CFR Part 11 audit trails.
Рекомендуется
Embedded Systems with Calendar
The M48T58-70PC1 serves as a one-chip substitute for any embedded 8051, 68xx or x86 design that previously paired a 6264 SRAM with a discrete RTC such as the DS12885. Designers can replace both ICs with the single Timekeeper module while keeping the original JEDEC 8K x 8 SRAM socket, eliminating firmware updates and battery-management code. The 70 ns access time matches legacy 8-bit bus timing, and the BCD-coded RTC registers are read with the same MOVX instructions used for SRAM access. This shortens bill-of-materials cost and PCB area.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для M48T58-70PC1 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | M48T58Y-70PC1 | M48T08-100PC1 | M48T02-70PC1 | DS1643-100+ | DS1225AD-150+ |
|---|---|---|---|---|---|---|
| Package | 28-DIP Module (0.600 inch) | 28-DIP Module (0.600 inch) - same | 28-DIP Module (0.600 inch) - same | 24-DIP Module - smaller, subset pinout | 28-DIP Module (0.600 inch) - same | 28-DIP Module (0.600 inch) - same |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Analog Devices (Maxim) | Analog Devices (Maxim) |
| Memory Size | 64 Kbit (8K x 8) | 64 Kbit (8K x 8) | 64 Kbit (8K x 8) | 16 Kbit (2K x 8) | 64 Kbit (8K x 8) | 64 Kbit (8K x 8) |
| Access Time | 70 ns | 70 ns | 100 ns (+43%) | 70 ns | 100 ns (+43%) | 150 ns (+114%) |
| Supply Voltage | 4.75 V to 5.5 V | 4.75 V to 5.5 V | 4.75 V to 5.5 V | 4.75 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Integrated RTC | Yes (BCD calendar) | Yes | Yes | Yes | Yes | No |
| Integrated Battery | Yes (10 years typical) | Yes | Yes (older gen) | Yes | Yes | Yes |
| JEDEC 8K x 8 Pinout | Yes (6264-compatible) | Yes | Yes | No (2K x 8, 24-pin) | Yes | Yes |
| Mounting Type | Through-Hole (DIP Module) | Through-Hole | Through-Hole | Through-Hole | Through-Hole | Through-Hole |
Ключевые отличия
- Same die and same family as M48T58Y-70PC1 (против M48T58Y-70PC1)
- 30% faster access time vs older M48T08 generation (против M48T08-100PC1)
- Cross-brand 5 V Timekeeper substitute (против DS1643-100+)
Заметки по проектированию
Estimated: at VCC = 5.0 V, the M48T58-70PC1 draws roughly 50 mA active (per typical 5 V Timekeeper SRAM spec) and falls to nanoamp-level battery current when VCC drops below the write-protect threshold. Place a 0.1 uF ceramic decoupling capacitor as close as possible to the VCC pin (pin 28) and add a 10 uF bulk capacitor at the supply rail to suppress the inrush during power-up, which otherwise can trigger the internal power-fail comparator prematurely.
Route the parallel address and data bus with matched trace lengths and keep /WE, /CE, and OE control traces short and well-decoupled to avoid bus contention during read/write transitions. The DIP Module package is through-hole; allow 2.54 mm pad pitch on the PCB. Because the module houses a lithium battery, do not place it adjacent to high-temperature heatsinks and respect the storage temperature limit on the reel/tube during assembly.
Common pitfalls: (1) Do NOT write to the RTC register addresses during the SRAM access window - the M48T58-70PC1 multiplexes RTC into the SRAM address space, so accidental writes corrupt the calendar; (2) Do not block /WE to ground; the write-protect circuit requires /WE to track VCC fall; (3) Treat the CAPHAT battery as non-replaceable - plan module replacement rather than cell replacement at end of life.
Информация о соответствии
RoHS compliance per ST product page. Not AEC-Q100 qualified (industrial/consumer Timekeeper SRAM). Contains an internal lithium cell - special shipping rules for battery-containing modules may apply.
