10M16DAU324I7P - MAX 10 FPGA 16K LE 246 I/O | Intel | 324-LFBGA
MPN: 10M16DAU324I7P ✓ Hoạt động10M16DAU324I7P Tóm tắt
An FPGA (Field Programmable Gate Array) is a class of programmable logic device that allows hardware designers to configure digital logic blocks and interconnects after manufacture. Within the broader semiconductor taxonomy, FPGAs sit above ASICs and CPLDs in flexibility but below microcontrollers in ease of programming. The MAX 10 family specifically integrates a hard processor subsystem, dual-configuration flash, and analog blocks onto a single die, targeting cost-sensitive industrial, automotive, and IoT applications.
Key features of the 10M16DAU324I7P include 16,000 logic elements organized into Adaptive Logic Modules (ALMs), 549 kbit of embedded SRAM, 2.5 Mb of user flash memory, and 246 GPIO pins supporting LVDS, LVCMOS, SSTL, and other I/O standards. The device operates from a 1.2 V core supply with I/O banks supporting 1.2V to 3.3V, and integrates a hard Nios II processor interface for soft-core SoC designs.
The MAX 10 architecture uses TSMC 55 nm embedded flash process technology, combining LUT-based logic fabric with hard IP blocks including PLLs, ADC, and temperature-sensing diodes. This monolithic integration eliminates external boot memory and reduces BOM cost. The dual-boot flash supports field upgrades with zero downtime through the On-Line Update feature.
Typical applications include industrial motor control, factory automation I/O expansion, video bridging, low-cost ASIC replacement, sensor fusion, and portable instrumentation. The integrated 12-bit ADC simplifies analog front-end designs.
When designing with this part, allocate sufficient PCB area for the 0.8 mm pitch LFBGA-324 footprint and route all power rails with adequate decoupling. The Quartus Prime design tool supports the full MAX 10 family with unified place-and-route.
This page synthesizes distributor pricing, same-family drop-in alternatives from the Site MPN list, and practical board-level design notes not collected in a single place on the Intel datasheet.
Bộ thay thế dễ dàng lắp đặt cho 10M16DAU324I7P — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với 10M16DAU324I7P (cùng hình factor và footprint) — khác nhau ở Package, Process Technology, Logic Elements (LE), Configuration Memory, Speed Grade.
10M16DAU324I7G
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
10M16DAU324C8G
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →10M16DAU324A7G
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
10M08DAU324I7G
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →10M08DAU324C8G
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →10M16DAU324I7P Tỷ lệ tối đa & tính chất điện
| Family | MAX 10 |
| Logic Elements | 16000 |
| User I/O Count | 246 |
| Embedded Memory | 549 kbit |
| Embedded Multipliers (18x18) | 246 |
| Hộp | 324-LFBGA (UBGA-324) |
| Operating Supply Voltage (Core) | 1.2 V |
| Minimum Operating Temperature | -40 C |
| Maximum Operating Temperature | +100 C |
| Speed Grade | 7 |
| Temperature Grade | Industrial (I) |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân 10M16DAU324I7P 324-lfbga (ubga-324)
Cấu hình chân cho 10M16DAU324I7P (324-lfbga (ubga-324) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho 10M16DAU324I7P.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
10M16DAU324I7P phù hợp cho 6 Áp dụngs: Industrial Motor Control, Factory Automation I/O Expansion, Video Bridging and Display Aggregation, Low-Cost ASIC Replacement, Sensor Fusion and IoT Edge Nodes, Portable Test and Measurement.
Industrial Motor Control
The 10M16DAU324I7P fits industrial motor control because its 16K logic elements comfortably handle field-oriented control (FOC) algorithms, sensorless observers, and multi-axis coordination at 32 kHz PWM update rates. The integrated 12-bit 1 MSPS ADC samples phase currents synchronously to PWM events without an external analog front-end, while 246 I/Os drive high-resolution encoder interfaces, resolver excitation, and gate-driver signals. The on-chip flash and dual-configuration boot allow in-field firmware upgrades between production runs. At 1.2 V core and industrial -40 to +100 C operation, the device tolerates factory-floor thermal stress.
Được đề xuất
Factory Automation I/O Expansion
For PLC backplane and distributed I/O blocks, the 10M16DAU324I7P provides 246 user I/Os at 0.8 mm pitch, supporting LVDS, RS-485, 24 V field-bus isolators, and parallel industrial Ethernet interfaces. The 549 kbit embedded memory buffers high-speed packet inspection and timestamp data. Industrial temperature grade (-40 to +100 C) and 1.2 V core simplify MTBF analysis. Designers can map EtherCAT or PROFINET soft IP into the same die, eliminating a companion ASIC. The MAX 10 dual-boot flash supports redundant firmware for zero-downtime field updates.
Được đề xuất
Video Bridging and Display Aggregation
The 10M16DAU324I7P can aggregate multiple MIPI CSI-2 or parallel CMOS camera inputs into a single USB3 or Ethernet output in video bridging applications. The 246 18x18 multipliers accelerate JPEG/H.264 encoding, while 549 kbit block RAM holds multiple video line buffers without external SDRAM. The industrial temperature range covers outdoor surveillance and machine-vision enclosures. The 324-LFBGA package delivers the I/O density required for 8-bit parallel camera interfaces and HDMI/DVI output bridges. On-chip flash cuts BOM cost versus SRAM-based FPGAs.
Được đề xuất
Low-Cost ASIC Replacement
The 10M16DAU324I7P replaces custom ASICs in volumes below 100K units where NRE charges are uneconomical. With 16K LEs, 246 I/Os, hard ADC, on-chip flash, and 1.2 V operation, the MAX 10 integrates nearly all glue logic of a typical mixed-signal ASIC. Industrial temperature grade supports automotive and industrial markets. The dual-boot flash and JTAG-based programming eliminate the need for an external boot PROM. Designers prototype on the MAX 10 dev kit then move to production boards with the same 324-LFBGA footprint.
Được đề xuất
Sensor Fusion and IoT Edge Nodes
Edge-sensor aggregation nodes use the 10M16DAU324I7P to interface multiple SPI, I2C, and UART sensors, then pre-process and compress data before forwarding to a host MCU. The 549 kbit embedded memory holds moving-window statistics and FIR filter taps; the 246 18x18 multipliers accelerate FFT and Kalman filter math. The integrated 12-bit ADC samples analog environmental sensors (temperature, pressure) without an external ADC chip. Industrial temperature range supports outdoor deployment, while the 324-LFBGA package's compact 19 mm x 19 mm footprint suits small-form-factor sensor hubs.
Được đề xuất
Portable Test and Measurement
Handheld oscilloscopes, logic analyzers, and protocol testers leverage the 10M16DAU324I7P's high I/O count to capture multiple channels at 200 MHz+ while running on-board DSP for FFT, eye-diagram, and protocol decode. The integrated 12-bit ADC eliminates an external mixed-signal front end for low-bandwidth channels. Industrial -40 to +100 C support covers bench-to-field portable instruments. The on-chip flash simplifies factory calibration storage, and the 549 kbit block RAM buffers deep acquisition captures. USB3, Ethernet, or PCIe soft IP can be implemented in the same die to streamline BOM.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho 10M16DAU324I7P — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | 10M16DAU324I7G | 10M16DAU324C8G | 10M16DAU324A7G | 10M08DAU324I7G | 10M08DAU324C8G |
|---|---|---|---|---|---|---|
| Package | 324-LFBGA (UBGA-324) | 324-LFBGA | 324-LFBGA | 324-LFBGA | 324-LFBGA | 324-LFBGA |
| Brand | Intel | Intel | Intel | Intel | Intel | Intel |
| Logic Elements | 16000 | 16000 | 16000 | 16000 | 8000 | 8000 |
| User I/Os | 246 | 246 | 246 | 246 | 246 | 246 |
| Embedded Memory | 549 kbit | 549 kbit | 549 kbit | 549 kbit | 378 kbit | 378 kbit |
| Temperature Grade | Industrial -40 to +100 C | Industrial -40 to +100 C | Commercial 0 to +85 C | Automotive -40 to +125 C (AEC-Q100) | Industrial -40 to +100 C | Commercial 0 to +85 C |
| Speed Grade | 7 | 7 | 8 | 7 | 7 | 8 |
| AEC-Q100 Qualified | No | No | No | Yes | No | No |
Bảo phân biệt quan trọng
- Highest I/O density in MAX 10 10M16 family (vs10M16DAF484I7P)
- Industrial temperature grade with maximum density (vs10M16DAU324C8G)
- Lower density drop-in for cost-optimized designs (vs10M08DAU324I7G)
Ghi chú thiết kế
The 324-LFBGA package uses 0.8 mm ball pitch. Follow Intel AN 532 for land pattern, solder-mask-defined (SMD) vs non-solder-mask-defined (NSMD) pad choice, and reflow profile. SMD pads with a 0.35 mm copper pad diameter and 0.65 mm solder-mask opening are recommended for robust BGA joint formation. Allow at least 6 layers with dedicated ground and 1.2 V power planes beneath the device to provide low-impedance current return paths for the high-speed I/O and ADC.
The 10M16DAU324I7P requires multiple supply rails: 1.2 V core (VCCINT), 1.2 V or 2.5 V PLL analog (VCCA), 2.5 V or 3.3 V configuration (VCCIO7/8 for configuration banks), and per-bank VCCIO for I/O standards. Decouple each rail with 100 nF X7R ceramic capacitors placed within 2 mm of each power pin, plus bulk 10-47 uF tantalum or polymer capacitors on the board. Sequence VCCINT before VCCIO per Intel Power-Up sequencing guidelines to avoid latch-up. The integrated ADC requires a clean 2.5 V analog supply separate from digital 2.5 V.
Estimated: at maximum toggling activity and 246 I/O switching simultaneously, dynamic current can exceed 500 mA on the 1.2 V core. Designers should budget thermal dissipation for the LFBGA package, which has theta-JA around 25 C/W on a standard 4-layer JEDEC test board. Provide thermal vias under the central ball array to the opposite copper plane. JTAG configuration pins (TCK, TMS, TDI, TDO) must not be left floating - add 10 kohm pull-ups to VCCIO7 to keep the device in a known state during power-up.
Thông tin tuân thủ
Industrial-grade MAX 10 FPGA; RoHS and REACH compliant per Intel product declaration. For AEC-Q100 qualified version, choose 10M16DAU324A7G.
