ATSAMG55J19B-MU - 120MHz Cortex-M4 MCU | Microchip
MPN: ATSAMG55J19B-MU ✓ Hoạt độngATSAMG55J19B-MU Tóm tắt
A microcontroller is a semiconductor containing a processor core, program memory, data memory, peripherals, and communication interfaces on one integrated circuit. The ATSAMG55J19B-MU belongs to the hierarchy of 32-bit microcontroller, Arm Cortex-M4 processor, embedded processor, and semiconductor. Its Cortex-M4F architecture supports efficient floating-point calculations, helping designers reduce instruction counts and active processing time in control, monitoring, and signal-processing workloads.
Three headline features distinguish this device. Its 120 MHz operating frequency provides high compute throughput for responsive embedded control. Its 512 KB flash memory provides substantial space for firmware, application code, configuration data, and update routines. The 64-QFN package occupies a compact 7.5 x 7.5 mm footprint while supporting a broad pin count for integrated peripherals and external connections. The stated 1.62 V to 3.6 V operating voltage also supports battery-backed and low-voltage industrial designs.
The processor combines a 32-bit Arm Cortex-M4 core with an FPU, making it appropriate for applications involving sensor conversion, motor algorithms, communications, and real-time control. Microchip describes the FPU as improving throughput while helping reduce active-power consumption and time to sleep. Designers should treat available peripheral functions, memory organization, clock behavior, and package pin assignments as authoritative requirements from the manufacturer datasheet before finalizing firmware or PCB connections.
Typical uses include industrial sensor nodes, motor and motion controllers, building automation equipment, connected meters, communications modules, and low-power embedded gateways. The ATSAMG55J19B-MU is particularly suitable when firmware needs both local real-time processing and moderate onboard program storage without moving those functions into a separate processor.
A critical design step is preserving signal and power integrity in the dense 64-QFN layout. Follow the manufacturer’s recommended decoupling, exposed-pad thermal, and high-speed layout guidance. Confirm the exact pin assignments and exposed-pad connection in the manufacturer datasheet before fabrication, and verify that the selected PCB footprint matches the 7.5 x 7.5 mm package.
This page combines the exact ATSAMG55J19B-MU ordering information, electrical and packaging characteristics, verified drop-in replacement analysis, application guidance, and PCB-focused design notes to support faster component selection and hardware bring-up.
Bộ thay thế dễ dàng lắp đặt cho ATSAMG55J19B-MU — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATSAMG55J19B-MU (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature, Audio Interface, Core Architecture, Core Processor.
ATSAMG55J19A-MU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMG55J19B-MU Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit ARM Cortex-M4 microcontroller |
| Processor Core | Arm Cortex-M4 with FPU |
| Architecture | ARMv7-M |
| Maximum CPU Frequency | 120 MHz |
| Flash Memory | 512 KB (512K x 8) |
| Điện áp cung cấp hoạt động | 1.62 V to 3.6 V |
| CPU Word Size | 32 bit |
| Floating-Point Unit | Yes |
| Package Type | 64-QFN |
| Package Dimensions | 7.5 mm x 7.5 mm |
| Kiểu lắp đặt | Surface mount |
| Product Series | SAM G55 |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân ATSAMG55J19B-MU 7.5 mm x 7.5 mm
Cấu hình chân cho ATSAMG55J19B-MU (7.5 mm x 7.5 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho ATSAMG55J19B-MU.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ATSAMG55J19B-MU phù hợp cho 6 Áp dụngs: Industrial Sensor and Condition Monitoring, Motor Control and Motion Systems, Building Automation and HVAC Control, Connected Metering and IoT Gateway, Communications and Protocol Gateway, Portable and Battery-Powered Equipment.
Industrial Sensor and Condition Monitoring
The ATSAMG55J19B-MU fits industrial condition-monitoring nodes that must process sensor information and manage communications within a compact 64-QFN footprint. Its Arm Cortex-M4F core operates up to 120 MHz, while the FPU accelerates numerical operations commonly found in filtering, calibration, and signal analysis. The 512 KB flash provides room for application firmware, device drivers, logging routines, and configuration data. At a 1.62 V to 3.6 V operating range, the device also accommodates low-voltage industrial sensing architectures. Designers should verify the required analog interfaces, timers, communication peripherals, and environmental limits against the manufacturer datasheet before choosing the exact device variant.
Được đề xuất
Motor Control and Motion Systems
The ATSAMG55J19B-MU is suitable for compact motor-control and motion-control subsystems requiring deterministic computation without a separate processor. Its 120 MHz Cortex-M4F core can execute control loops, position logic, and communications while the floating-point unit supports filtering and transformation calculations. The 512 KB flash allows substantial firmware for motion algorithms, fault handling, and parameter storage. The 64-QFN, 7.5 x 7.5 mm package helps limit board area, although careful pin planning is needed for timing signals, position feedback, communications, and power. Confirm PWM, capture, timer, and comparator resources in the manufacturer datasheet and verify the motor-drive power stage separately.
Được đề xuất
Building Automation and HVAC Control
The ATSAMG55J19B-MU supports building automation, HVAC, and environmental-control modules that coordinate sensors, actuators, and network interfaces. Its 120 MHz Cortex-M4F processing capability allows the controller to execute control laws and protocol handling concurrently, while 512 KB flash provides adequate space for configuration, schedules, and application firmware. The device’s 1.62 V to 3.6 V operating range can fit low-energy centralized or distributed control nodes. The compact 64-QFN package also supports space-constrained equipment panels. Before schematic capture, verify the required timers, serial interfaces, analog channels, watchdog behavior, and operating-temperature requirements for the target HVAC installation.
Được đề xuất
Connected Metering and IoT Gateway
The ATSAMG55J19B-MU is well matched to connected metering and IoT gateway designs that combine local measurement, protocol handling, and remote communications. The 120 MHz Cortex-M4F core provides processing headroom for packet work and real-time acquisition, while the floating-point unit supports calibration and conversion routines. Its 512 KB flash can hold networking stacks, device drivers, firmware update logic, and local configuration. A 7.5 x 7.5 mm 64-QFN package helps reduce board size in distributed meter hardware. The design must still allocate regulators, radio or network interfacing, decoupling, and protection, while validating serial-interface resources and low-power requirements in the manufacturer documentation.
Được đề xuất
Communications and Protocol Gateway
The ATSAMG55J19B-MU can serve as the host processor in a communications or protocol gateway when deterministic packet processing and peripheral integration are priorities. Its 120 MHz Arm Cortex-M4F architecture executes control and framing tasks efficiently, and the 512 KB flash provides room for multiple protocol stacks, routing tables, diagnostics, and configuration. The MCU’s compact 64-QFN package is useful in small gateways where board area and power are constrained. Its 1.62 V to 3.6 V supply range also permits integration with efficient 3.3 V power systems. Confirm the availability, electrical characteristics, and multiplexing of required UART, SPI, USB, or other communication interfaces in the manufacturer datasheet.
Được đề xuất
Portable and Battery-Powered Equipment
The ATSAMG55J19B-MU supports portable and battery-powered equipment that requires substantial local processing in a compact package. Its Cortex-M4F processor operates up to 120 MHz and includes an FPU, allowing numerical work to be completed with fewer instructions than a software-heavy approach. Microchip describes this capability as supporting higher throughput, lower active-power consumption, and faster sleep transitions. The device’s 1.62 V minimum operating voltage fits low-voltage power architectures, while 512 KB flash stores compact applications and update logic. Actual battery life depends on firmware, peripherals, sleep modes, and the system power tree, so validate the complete duty cycle and verify low-power specifications for the selected device and package.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATSAMG55J19B-MU — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATSAMG55J19A-MU |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 64-QFN (7.5 x 7.5 mm) | 64-QFN (7.5 x 7.5 mm) |
| Processor Core | Arm Cortex-M4 with FPU | Arm Cortex-M4 with FPU |
| Maximum CPU Frequency | 120 MHz | 120 MHz |
| Flash Memory | 512 KB | 512 KB |
| CPU Word Size | 32 bit | 32 bit |
| Device Revision | B | A |
Bảo phân biệt quan trọng
- Revision-specific sourcing for designs originally specified around revision B (vsATSAMG55J19A-MU)
- Floating-point performance for embedded numerical workloads (vsATSAMG55J19A-MU)
- Compact integration for space-constrained embedded products (vsATSAMG55J19A-MU)
Ghi chú thiết kế
Assign the ATSAMG55J19B-MU footprint only after checking the exact 64-QFN, 7.5 x 7.5 mm package drawing, terminal lengths, and exposed-pad geometry in the manufacturer documentation. Place decoupling capacitors close to their intended power pins and route them without long loops through surrounding circuitry. The exposed pad is normally part of the thermal and electrical design rather than an optional copper feature; confirm whether it connects to ground and follow the prescribed via-array pattern before releasing the PCB.
Design the power tree around the stated 1.62 V to 3.6 V operating range. Use the manufacturer reference circuit to determine the required supply topology, startup behavior, and decoupling values. Check every peripheral’s voltage tolerance before connecting 5 V-tolerant or externally powered signals. If the board also supports battery operation, define a controlled transition between battery, regulator, and backup supplies to avoid uncontrolled back-powering or sequencing violations at the MCU pins.
The 64-QFN package can conduct heat through its exposed pad, but the required thermal performance depends on the PCB copper area, via pattern, enclosure, ambient temperature, and processing load. Use the package drawing’s exposed-pad and via recommendations rather than estimating a land pattern independently. Validate the hottest operating condition with thermocouples or thermal simulation, and avoid placing heat-generating regulators or power components directly beneath the MCU when that arrangement raises junction temperature.
Separate sensitive analog inputs, communication lines, and clock signals from noisy switching nodes on the PCB. Use a continuous ground reference where possible, keep return paths short, and avoid routing high-current or fast-switching traces beneath sensitive nets. External communication or memory interfaces should follow the manufacturer’s signal-integrity guidance for length, impedance, and grounding. Firmware should also configure unused pins and peripheral states deliberately rather than relying on a generic reset default.
Thông tin tuân thủ
RoHS compliance is identified for the exact ATSAMG55J19B-MU product listing. Additional environmental, automotive, and material-compliance attributes require current manufacturer declarations for the selected order code.