DS90C402M/NOPB Dual LVDS Receiver | Texas Instruments
MPN: DS90C402M/NOPB ✓ Hoạt độngDS90C402M/NOPB Tóm tắt
Bộ thay thế dễ dàng lắp đặt cho DS90C402M/NOPB — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DS90C402M/NOPB (cùng hình factor và footprint) — khác nhau ở Package, Number of Receivers, Operating Temperature Range.
DS90C402M
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DS90C402MX/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DS90C402M/NOPB Thông số kỹ thuật
| Product Type | Dual LVDS receiver |
| Number of Receivers | 2 |
| Receiver Threshold Sensitivity | ±100 mV |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Receiver Propagation Delay | 1.5 ns |
| Protocol | LVDS |
| Khoảng nhiệt độ hoạt động | -40 °C to 85 °C |
| Hộp | 8-SOIC, 0.154 inch, 3.90 mm width |
| Số lượng chân | 8 |
| Kiểu lắp đặt | Surface mount |
| Common-Mode Noise Protection | Supported |
| Application Configuration | Dual high-speed point-to-point interface |
| Compatible Transmitter Family | DS90C401 |
| Packaging | Tube |
| Lead-Free Status | Lead-free part designation |
| Trạng thái vòng đời | Active |
Hướng dẫn cấu hình chân DS90C402M/NOPB 8-soic, 0.154 inch, 3.90 mm width
Cấu hình chân cho DS90C402M/NOPB (8-soic, 0.154 inch, 3.90 mm width gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho DS90C402M/NOPB.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DS90C402M/NOPB phù hợp cho 6 Áp dụngs: Dual High-Speed Point-to-Point Links, Industrial Control and Data Acquisition, Test and Measurement Equipment, Embedded Communication Interfaces, Video and Imaging Data Reception, Low-Power Industrial Sensor Interfaces.
Dual High-Speed Point-to-Point Links
The DS90C402M/NOPB is suitable for two independent high-speed LVDS receiver channels in point-to-point equipment. Its dual-receiver organization reduces the number of receiver packages required when two data paths share the same board, while the 1.5 ns propagation delay supports short-latency communication. The device operates from 4.5 V to 5.5 V and provides ±100 mV threshold sensitivity, making it appropriate for compact industrial and test interfaces that need reliable detection of small differential signals. Keep the two input pairs routed with matched impedance, provide a continuous return path, and confirm receiver-versus-transmitter timing across the complete link.
Được đề xuất
Industrial Control and Data Acquisition
The DS90C402M/NOPB can receive differential data from remote sensors, controllers, or data-acquisition modules in industrial equipment. Its common-mode noise protection is useful when the receiver shares wiring or board space with switching circuitry, and the -40 °C to 85 °C range supports a broad range of ambient conditions. Two receiver channels can handle paired command or measurement signals without duplicating the receive function. The design should preserve the intended LVDS signal integrity with controlled impedance, uninterrupted reference planes, minimized stubs, and local supply bypassing around the 4.5 V to 5.5 V rail.
Được đề xuất
Test and Measurement Equipment
The DS90C402M/NOPB fits instrumentation that receives low-amplitude differential signals from external fixtures, probes, or remote test nodes. The ±100 mV threshold and common-mode protection help distinguish small useful differential signals from noise imposed on the pair, while the 1.5 ns propagation delay assists with high-speed timing budgets. Use the device with properly terminated differential routing and a stable 5 V supply. Care should be taken to keep switching regulators, clocks, and high-current return paths away from the receiver inputs, and the complete input network should be validated with an eye diagram or equivalent signal-integrity measurement.
Được đề xuất
Embedded Communication Interfaces
The DS90C402M/NOPB can provide two LVDS receive paths for embedded controllers, peripheral modules, and board-to-board communication links. Its 8-SOIC package offers a compact surface-mount solution, and the dual-channel configuration simplifies termination and receiver placement near the connector. The 4.5 V to 5.5 V operating range is compatible with conventional 5 V digital interfaces, while the low 1.5 ns receiver delay supports efficient data transfer. Confirm the transmitting device’s output levels, timing, and common-mode limits, and route each differential pair as a coupled pair over a continuous ground or reference plane.
Được đề xuất
Video and Imaging Data Reception
The DS90C402M/NOPB may be used in imaging and video systems that transfer differential data between a transmitter, processor, or display-related controller. Its two receivers allow paired data paths to be handled in one package, and the ±100 mV threshold is useful for low-amplitude differential signaling. The receiver delay of 1.5 ns supports high-speed links, but the complete timing budget must include the transmitter, cable or PCB propagation, and downstream logic. Maintain controlled differential impedance, avoid discontinuities, and verify common-mode voltage and input protection against the actual source device.
Được đề xuất
Low-Power Industrial Sensor Interfaces
The DS90C402M/NOPB is suitable for receiving low-power differential sensor or control signals where board area and power consumption are important. The device is optimized for low-power applications and provides two receiver channels in a single 8-SOIC package. Its ±100 mV threshold can support low-amplitude links, while common-mode protection helps reject noise coupled into wiring. The system should use a regulated supply within 4.5 V to 5.5 V, place bypass capacitance near the device, and preserve a controlled return path so external cable noise does not degrade the differential signal.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DS90C402M/NOPB — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DS90C402M | DS90C402MX/NOPB |
|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Function | Dual LVDS receiver | Dual LVDS receiver | Dual LVDS receiver |
| Number of Receivers | 2 | 2 | 2 |
| Number of Drivers | 0 | 0 | 0 |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Receiver Threshold Sensitivity | ±100 mV | ±100 mV | ±100 mV |
| Receiver Propagation Delay | 1.5 ns | 1.5 ns | 1.5 ns |
| Operating Temperature Range | -40 °C to 85 °C | -40 °C to 85 °C | -40 °C to 85 °C |
| Protocol | LVDS | LVDS | LVDS |
| Common-Mode Noise Protection | Supported | Supported | Supported |
Bảo phân biệt quan trọng
- Two LVDS receiver channels in one package (vsDS90C402M)
- Compact 8-SOIC footprint (vsDS90C402MX/NOPB)
- High-speed receiver performance (vsDS90C402M)
Ghi chú thiết kế
Route each LVDS input as a tightly coupled differential pair over a continuous reference plane. Avoid stubs, test pads without appropriate termination, and large discontinuities that can degrade the ±100 mV receiver threshold. Keep the receiver close to the connector or transmitter interface when practical, and use manufacturer-recommended differential impedance and termination values. The complete channel, including transmitter, PCB, cable, and receiver, should be validated for eye opening and jitter.
Place the DS90C402M/NOPB close to the interface connector or companion transmitter and provide a low-impedance 5 V supply connection. Add local bypass capacitance at the device supply pins in accordance with the TI application guidance. Maintain a short return path beneath the differential pair and separate the LVDS routing from noisy switching nodes and high-current power paths to preserve common-mode noise rejection.
Do not substitute the DS90C401 transmitter for a DS90C402 receiver based only on package similarity; the devices have different signal roles. Likewise, verify the exact orderable suffix, pinout, supply limits, and production status before approving a replacement. Check differential input polarity against the manufacturer pin-description table and review system timing with the 1.5 ns receiver delay included alongside transmitter and interconnect delay.
Thông tin tuân thủ
The /NOPB ordering designation and lead-free status are identified in the product information. RoHS, REACH, halogen-free, and conflict-minerals status are not established by the cited product snippets and should be confirmed in the manufacturer compliance documentation.