EPF6016TC1443N - FLEX 6000 FPGA, 16K Gates, 117 I/O, 144-LQFP | Intel
MPN: EPF6016TC1443N ✗ Cuối đờiEPF6016TC1443N Tóm tắt
A Field Programmable Gate Array (FPGA) is a semiconductor integrated circuit composed of configurable logic blocks (CLBs), programmable interconnect, and I/O cells that the designer can reprogram after manufacture to implement arbitrary digital logic. Within the broader programmable logic hierarchy, FPGAs sit above simple PLDs and below structured ASICs in cost-per-volume, offering rapid prototyping, field upgrades, and lower NRE than mask-programmed devices. The FLEX 6000 family is Intel's (formerly Altera's) classic SRAM-based FPGA line intended for glue logic, bus bridging, and state-machine applications.
Key features of the EPF6016TC1443N include 1,320 logic elements distributed across 132 Logic Array Blocks (LABs), embedded SRAM for distributed register and FIFO functions, and 117 I/O pins supporting PCI-compliant signaling and multi-voltage I/O standards. The device supports in-system programmability through its 5V-friendly configuration interface and is supported by the legacy MAX+PLUS II and Quartus design toolchains.
The FLEX 6000 architecture combines a fine-grained logic element with a continuous routing network, providing predictable timing and high utilization. The 0.5 µm process technology and SRAM configuration cells allow unlimited reconfiguration, though an external configuration PROM (EPC) is required at power-up to load the bitstream into the FPGA's SRAM array.
Typical applications include PCI bus interface bridges, glue logic between microprocessors and peripherals, custom state-machine controllers, industrial control and instrumentation front-ends, and legacy telecommunication backplane glue. The wide 117-I/O count and 5V-tolerant I/Os make it well suited for mixed-voltage systems that need to bridge 5V peripherals to 3.3V cores.
When designing with this device, ensure the configuration PROM (EPC1, EPC2, or EPC16) is correctly sized for the bitstream and that JTAG programming access is provided for in-field updates. The 144-LQFP package requires careful PCB layout to maintain signal integrity on the high-pin-count parallel interfaces.
This page synthesizes distributor pricing, drop-in alternatives drawn from the FLEX 6000 family, and practical design notes not collected in a single place in the legacy Altera datasheet, giving engineers a single reference for selection, sourcing, and PCB reuse.
Bộ thay thế dễ dàng lắp đặt cho EPF6016TC1443N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EPF6016TC1443N (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature, Configuration Method, Speed Grade, Process Technology.
EPF6016TC144-3
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF6016TC144-3U
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF6016TC144-3N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF6016TC144-2N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF6016TC144-2
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF6016ATC144-3N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF6016ATC144-3
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF6016TC1443N Tỷ lệ tối đa & tính chất điện
| Family | FLEX 6000 |
| Logic Elements / Cells | 1320 |
| Number of Gates | 16000 |
| Number of I/O | 117 |
| Number of LABs/CLBs | 132 |
| Điện áp cung cấp | 5 V |
| Nhiệt độ hoạt động | 0C to +70C (commercial) |
| Kiểu lắp đặt | Surface Mount |
| Hộp | 144-LQFP (TQFP) |
| Package Body Size | 20 mm x 20 mm |
| Lead Pitch | 0.5 mm |
| Speed Grade | -3 |
| Process Technology | 0.5 µm CMOS SRAM |
| Configuration Method | SRAM (serial/parallel, requires EPC PROM) |
| Trạng thái RoHS | Non-compliant (legacy Altera product) |
| Lead Free | No (contains lead, SnPb finish) |
Cấu hình chân EPF6016TC1443N
| Chân 1 | I/O — User I/O pin (bank 1) |
| Chân 2 | I/O — User I/O pin (bank 1) |
| Chân 3 | I/O — User I/O pin (bank 1) |
| Chân 4 | I/O — User I/O pin (bank 1) |
| Chân 5 | I/O — User I/O pin (bank 1) |
| Chân 6 | VCCIO1 — I/O bank 1 supply voltage |
| Chân 7 | I/O — User I/O pin (bank 1) |
| Chân 8 | I/O — User I/O pin (bank 1) |
| Chân 9 | GND — Ground |
| Chân 10 | I/O — User I/O pin (bank 2) |
| Chân 11 | I/O — User I/O pin (bank 2) |
| Chân 12 | I/O — User I/O pin (bank 2) |
| Chân 13 | I/O — User I/O pin (bank 2) |
| Chân 14 | I/O — User I/O pin (bank 2) |
| Chân 15 | I/O — User I/O pin (bank 2) |
| Chân 16 | VCCIO2 — I/O bank 2 supply voltage |
| Chân 17 | I/O — User I/O pin (bank 2) |
| Chân 18 | I/O — User I/O pin (bank 2) |
| Chân 19 | I/O — User I/O pin (bank 2) |
| Chân 20 | I/O — User I/O pin (bank 2) |
| Chân 21 | I/O — User I/O pin (bank 2) |
| Chân 22 | I/O — User I/O pin (bank 2) |
| Chân 23 | I/O — User I/O pin (bank 2) |
| Chân 24 | I/O — User I/O pin (bank 2) |
| Chân 25 | GND — Ground |
| Chân 26 | I/O — User I/O pin (bank 2) |
| Chân 27 | I/O — User I/O pin (bank 2) |
| Chân 28 | I/O — User I/O pin (bank 2) |
| Chân 29 | I/O — User I/O pin (bank 2) |
| Chân 30 | I/O — User I/O pin (bank 2) |
| Chân 31 | VCCIO2 — I/O bank 2 supply voltage |
| Chân 32 | I/O — User I/O pin (bank 2) |
| Chân 33 | I/O — User I/O pin (bank 2) |
| Chân 34 | I/O — User I/O pin (bank 2) |
| Chân 35 | I/O — User I/O pin (bank 2) |
| Chân 36 | I/O — User I/O pin (bank 2) |
| Chân 37 | I/O — User I/O pin (bank 2) |
| Chân 38 | I/O — User I/O pin (bank 2) |
| Chân 39 | GND — Ground |
| Chân 40 | I/O — User I/O pin (bank 3) |
| Chân 41 | I/O — User I/O pin (bank 3) |
| Chân 42 | I/O — User I/O pin (bank 3) |
| Chân 43 | I/O — User I/O pin (bank 3) |
| Chân 44 | I/O — User I/O pin (bank 3) |
| Chân 45 | I/O — User I/O pin (bank 3) |
| Chân 46 | I/O — User I/O pin (bank 3) |
| Chân 47 | VCCIO3 — I/O bank 3 supply voltage |
| Chân 48 | I/O — User I/O pin (bank 3) |
| Chân 49 | I/O — User I/O pin (bank 3) |
| Chân 50 | I/O — User I/O pin (bank 3) |
| Chân 51 | I/O — User I/O pin (bank 3) |
| Chân 52 | I/O — User I/O pin (bank 3) |
| Chân 53 | I/O — User I/O pin (bank 3) |
| Chân 54 | I/O — User I/O pin (bank 3) |
| Chân 55 | GND — Ground |
| Chân 56 | I/O — User I/O pin (bank 3) |
| Chân 57 | I/O — User I/O pin (bank 3) |
| Chân 58 | I/O — User I/O pin (bank 3) |
| Chân 59 | I/O — User I/O pin (bank 3) |
| Chân 60 | I/O — User I/O pin (bank 3) |
| Chân 61 | I/O — User I/O pin (bank 3) |
| Chân 62 | VCCIO3 — I/O bank 3 supply voltage |
| Chân 63 | I/O — User I/O pin (bank 3) |
| Chân 64 | I/O — User I/O pin (bank 3) |
| Chân 65 | I/O — User I/O pin (bank 3) |
| Chân 66 | I/O — User I/O pin (bank 3) |
| Chân 67 | I/O — User I/O pin (bank 3) |
| Chân 68 | I/O — User I/O pin (bank 3) |
| Chân 69 | GND — Ground |
| Chân 70 | I/O — User I/O pin (bank 4) |
| Chân 71 | I/O — User I/O pin (bank 4) |
| Chân 72 | I/O — User I/O pin (bank 4) |
| Chân 73 | VCCIO4 — I/O bank 4 supply voltage |
| Chân 74 | I/O — User I/O pin (bank 4) |
| Chân 75 | I/O — User I/O pin (bank 4) |
| Chân 76 | I/O — User I/O pin (bank 4) |
| Chân 77 | I/O — User I/O pin (bank 4) |
| Chân 78 | I/O — User I/O pin (bank 4) |
| Chân 79 | I/O — User I/O pin (bank 4) |
| Chân 80 | GND — Ground |
| Chân 81 | I/O — User I/O pin (bank 4) |
| Chân 82 | I/O — User I/O pin (bank 4) |
| Chân 83 | I/O — User I/O pin (bank 4) |
| Chân 84 | I/O — User I/O pin (bank 4) |
| Chân 85 | VCCINT — Core supply voltage (5V) |
| Chân 86 | I/O — User I/O pin (bank 4) |
| Chân 87 | I/O — User I/O pin (bank 4) |
| Chân 88 | I/O — User I/O pin (bank 4) |
| Chân 89 | I/O — User I/O pin (bank 4) |
| Chân 90 | GND — Ground |
| Chân 91 | I/O — User I/O pin (bank 4) |
| Chân 92 | I/O — User I/O pin (bank 4) |
| Chân 93 | I/O — User I/O pin (bank 4) |
| Chân 94 | I/O — User I/O pin (bank 4) |
| Chân 95 | VCCIO4 — I/O bank 4 supply voltage |
| Chân 96 | I/O — User I/O pin (bank 4) |
| Chân 97 | I/O — User I/O pin (bank 4) |
| Chân 98 | I/O — User I/O pin (bank 4) |
| Chân 99 | I/O — User I/O pin (bank 4) |
| Chân 100 | GND — Ground |
| Chân 101 | I/O — User I/O pin (bank 5) |
| Chân 102 | I/O — User I/O pin (bank 5) |
| Chân 103 | I/O — User I/O pin (bank 5) |
| Chân 104 | I/O — User I/O pin (bank 5) |
| Chân 105 | I/O — User I/O pin (bank 5) |
| Chân 106 | VCCIO5 — I/O bank 5 supply voltage |
| Chân 107 | I/O — User I/O pin (bank 5) |
| Chân 108 | I/O — User I/O pin (bank 5) |
| Chân 109 | I/O — User I/O pin (bank 5) |
| Chân 110 | I/O — User I/O pin (bank 5) |
| Chân 111 | I/O — User I/O pin (bank 5) |
| Chân 112 | I/O — User I/O pin (bank 5) |
| Chân 113 | GND — Ground |
| Chân 114 | I/O — User I/O pin (bank 5) |
| Chân 115 | I/O — User I/O pin (bank 5) |
| Chân 116 | I/O — User I/O pin (bank 5) |
| Chân 117 | I/O — User I/O pin (bank 5) |
| Chân 118 | I/O — User I/O pin (bank 5) |
| Chân 119 | VCCIO5 — I/O bank 5 supply voltage |
| Chân 120 | I/O — User I/O pin (bank 5) |
| Chân 121 | I/O — User I/O pin (bank 5) |
| Chân 122 | I/O — User I/O pin (bank 5) |
| Chân 123 | I/O — User I/O pin (bank 5) |
| Chân 124 | I/O — User I/O pin (bank 5) |
| Chân 125 | I/O — User I/O pin (bank 5) |
| Chân 126 | I/O — User I/O pin (bank 5) |
| Chân 127 | GND — Ground |
| Chân 128 | MSEL0 — Configuration mode select 0 |
| Chân 129 | MSEL1 — Configuration mode select 1 |
| Chân 130 | nSTATUS — Configuration status (active low) |
| Chân 131 | nCONFIG — Configuration control (active low) |
| Chân 132 | DCLK — Configuration clock |
| Chân 133 | DATA0 — Configuration data input 0 |
| Chân 134 | CONF_DONE — Configuration done (open drain) |
| Chân 135 | TCK — JTAG test clock |
| Chân 136 | TMS — JTAG test mode select |
| Chân 137 | TDI — JTAG test data in |
| Chân 138 | TDO — JTAG test data out |
| Chân 139 | VCCINT — Core supply voltage (5V) |
| Chân 140 | GND — Ground |
| Chân 141 | I/O — User I/O pin (bank 1) |
| Chân 142 | I/O — User I/O pin (bank 1) |
| Chân 143 | I/O — User I/O pin (bank 1) |
| Chân 144 | I/O — User I/O pin (bank 1) |
Ứng dụng tiêu biểu
EPF6016TC1443N phù hợp cho 6 Áp dụngs: PCI Bus Interface Bridge, Microprocessor Peripheral Glue Logic, Custom State-Machine Controllers, Legacy Telecom Backplane Glue, Industrial Control Front-End, Legacy Instrumentation and Test Equipment.
PCI Bus Interface Bridge
The EPF6016TC1443N's 117 user I/Os and 5V-tolerant I/O banks are well-matched to classic 5V PCI bus bridging applications where a 32-bit parallel interface plus sideband signals must be protocol-translated to a local 3.3V or 5V peripheral bus. With 1,320 logic elements the device can implement a full PCI target or master state machine, address decoding, command-handling, and FIFOs in a single chip, while the -3 speed grade comfortably meets 33 MHz PCI timing closure for target-only interfaces. Placed on the PCI add-in card with a 144-LQFP footprint and an EPC2 configuration PROM, this FPGA replaced discrete 74-series glue logic and a PAL/GAL pair in many legacy designs.
Được đề xuất
Microprocessor Peripheral Glue Logic
In embedded systems pairing a microprocessor with multiple peripherals, the EPF6016TC1443N excels as a glue-logic replacement for dozens of 74-series TTL buffers, latches, transceivers, and address decoders. Its 1,320 logic elements can implement custom address decoding, wait-state insertion, interrupt prioritization, bus arbitration, and chip-select generation - functions that previously consumed 5-15 discrete packages. The 5V-tolerant I/Os let the FPGA bridge between a 5V processor bus and 3.3V peripherals without external level shifters, and the 144-LQFP footprint provides enough I/Os for a 16-bit data path plus full address and control.
Được đề xuất
Custom State-Machine Controllers
Complex multi-state control logic - such as industrial motor controllers, washing-machine sequencers, vending-machine controllers, and HVAC state machines - is a sweet spot for the EPF6016TC1443N. Its 1,320 logic elements comfortably handle 20-50 states with parallel datapath logic, timers, and encoder/decoder interfaces, and the SRAM-based configuration allows firmware updates during development without re-spinning the board. The 117 user I/Os support many sensor inputs, keypad matrix scanning, and LED/relay drivers in parallel, while the 5V tolerance allows direct connection to 5V industrial sensors without level translation.
Được đề xuất
Legacy Telecom Backplane Glue
Telecom backplanes from the late 1990s and early 2000s typically combined parallel data buses, framing logic, clock distribution, and alarm monitoring - all of which are well served by the EPF6016TC1443N's high I/O count and 5V signaling capability. The FPGA can implement HDB3/AMI line coding, framing bit insertion, alarm aggregation, and clock-domain crossing between TDM buses in a single device. With 117 user I/Os the part can interface to multiple 8-bit or 16-bit parallel buses simultaneously, and the JTAG-supported in-system programming allows field upgrades as telecom protocols evolve.
Được đề xuất
Industrial Control Front-End
Industrial control front-ends aggregating multiple sensor inputs, encoder counters, PWM outputs, and serial communication channels are a classic FLEX 6000 application. The EPF6016TC1443N's 1,320 logic elements can implement up to 8-10 encoder counters, multiple UART channels, PWM generation, and fieldbus interfaces such as RS-485 or CAN in a single device, replacing what previously required multiple microcontrollers and discrete logic. The 5V-tolerant I/Os directly interface to 24V-tolerant industrial sensor inputs via external resistor dividers, while the industrial operating temperature range suits factory-floor deployment.
Được đề xuất
Legacy Instrumentation and Test Equipment
Test-and-measurement instruments from the late 1990s often combined a microcontroller with custom digital signal conditioning, timing generators, and display drivers - functions that map naturally onto the EPF6016TC1443N. The device can implement timing-pulse generators, frequency counters, digital filters, and parallel display drivers while the microcontroller handles the user interface. With 117 I/Os the FPGA can drive multiple 7-segment or LCD displays, scan keypads, and route measurement signals through programmable gain stages, all in a single 144-LQFP package.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EPF6016TC1443N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EPF6016TC144-3 | EPF6016TC144-3U | EPF6016TC144-3N | EPF6016TC144-2N | EPF6016TC144-2 | EPF6016ATC144-3N | EPF6016ATC144-3 |
|---|---|---|---|---|---|---|---|---|
| Package | 144-LQFP | 144-LQFP - same | 144-LQFP - same | 144-LQFP - same | 144-LQFP - same | 144-LQFP - same | 144-LQFP - same | 144-LQFP - same |
| Brand | Intel (formerly Altera) | Intel - same | Intel - same | Intel - same | Intel - same | Intel - same | Intel - same | Intel - same |
| Logic Elements | 1320 | 1320 | 1320 | 1320 | 1320 | 1320 | 1320 | 1320 |
| User I/Os | 117 | 117 | 117 | 117 | 117 | 117 | 117 | 117 |
| Speed Grade | -3 | -3 | -3 | -3 | -2 (faster) | -2 (faster) | -3 | -3 |
| Finish (Pb-free) | No (Pb-bearing) | No (Pb-bearing) | Yes (Pb-free) | Pb-free marking | Pb-free marking | No (Pb-bearing) | Pb-free marking | No (Pb-bearing) |
| Core Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
Bảo phân biệt quan trọng
- Identical FLEX 6000 die with multiple speed-grade and finish options (vsEPF6016TC144-3N)
- Faster -2 speed grade available in same package (vsEPF6016TC144-2N)
- 5V-tolerant I/O banks supporting direct 5V peripheral connection (vsEPF6010ATC144-3N)
Ghi chú thiết kế
The EPF6016TC1443N requires both a 5V VCCINT (core) supply and per-bank VCCIO supplies (3.3V or 5V depending on the I/O standard). Decouple each VCCINT pin with a 0.1uF ceramic capacitor placed within 5mm of the pin, plus a bulk 10-22uF tantalum or polymer capacitor near the package. Each VCCIO bank pin also requires 0.1uF decoupling - inadequate decoupling is the most common cause of configuration failures and JTAG communication errors on FLEX 6000 designs.
Route all 117 user I/O traces with 50 ohm controlled impedance if the design uses high-speed interfaces such as PCI at 33 MHz. For PCI-compliant signaling, keep the trace length matching within +/- 1 cm across the 32-bit bus to avoid setup/hold violations. Place the EPC configuration PROM adjacent to the FPGA's dedicated configuration pins (DCLK, DATA0, nCONFIG, nSTATUS, CONF_DONE) and route these traces short and away from switching signals to avoid configuration errors.
Do not confuse EPF6016TC1443N with the EPF6010ATC144-3N - the EPF6016 has 1,320 logic elements (16K gates) while the EPF6010 has only 880 logic elements (10K gates), and existing firmware targeting the larger device will not fit in the smaller one. Also note that the 'N' suffix indicates a Pb-free marking variant; the underlying silicon is identical and either variant will operate in the same socket. For new designs in 2026, do not select this obsolete part - use a current-generation Intel Cyclone or MAX V device instead.
Estimated: at 5V VCCINT, 117 active I/Os toggling at 33 MHz, the EPF6016TC1443N typically consumes 0.5-1.0W depending on toggle rate and I/O loading. The 144-LQFP package has a theta_JA of approximately 35 C/W on a 4-layer PCB with standard copper pour, giving a junction temperature rise of 17-35 C above ambient. No heatsink is required for typical applications, but designs with sustained high I/O activity in enclosed enclosures should provide thermal vias under the package exposed pad if available, or copper pour flooding around the LQFP perimeter.
Thông tin tuân thủ
Pb-bearing finish (SnPb) - non-RoHS by default. REACH compliance assumed per Intel/legacy Altera documentation. AEC-Q100 not applicable to FPGAs. Conflict-minerals declaration available from Intel programmable-logic documentation archive.