M1AFS250-FG256 - Fusion FPGA 250K Gates ARM Cortex-M1 | Microchip
MPN: M1AFS250-FG256 ✓ Hoạt độngM1AFS250-FG256 Tóm tắt
A fusion mixed-signal FPGA is a field-programmable gate array that combines flash-based programmable fabric with analog peripherals, flash memory blocks, and clock management on one monolithic die. Within the power/processing hierarchy, this places the M1AFS250 as a system-on-chip (SoC): FPGA fabric plus an ARM Cortex-M1 soft-processor core running at up to 350 MHz, bridging programmable logic and embedded MCU control without a discrete microcontroller.
Key features include 250K system gates (approximately 6,144 logic cells per the Microchip USA listing), 114 user I/O, comprehensive on-chip clock generation and management circuitry, and large flash memory blocks. The monolithic integration of configurable analog and digital fabric reduces board area and bill-of-materials count for mixed-signal control systems.
Technically, the M1AFS250 family is manufactured on a 130nm flash-based process (per Jotrin Electronics), offering nonvolatile, secure, instant-on configuration without an external configuration PROM. The FG256 package is a 1.00 mm ball pitch 256-ball BGA, surface-mount (SMD/SMT), supplied in tray packaging. Commercial temperature range is 0C to +70C. Note that this exact ordering code is RoHS non-compliant and contains lead; the FGG256 (Green) variant is the lead-free drop-in alternative on the same footprint.
Typical applications include industrial automation control, smart power motor control, portable instrumentation, and embedded systems requiring single-chip analog monitoring plus logic. The 1.5V core and flash fabric suit low-power, high-reliability designs.
Design consideration: verify the FGG256 (RoHS-compliant) alternative early, since the FG256 leaded version may face procurement and environmental restrictions in new designs.
This page synthesizes distributor pricing, drop-in same-footprint alternatives, and practical design notes not found in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho M1AFS250-FG256 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với M1AFS250-FG256 (cùng hình factor và footprint) — khác nhau ở System Gates, Configuration Memory, Series, Package, RoHS Status.
M1AFS250-FGG256
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →M1AFS250-2FG256I
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →M1AFS250-2FGG256
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →M1AFS250-2FGG256I
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →M1AFS600-2FG256
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →M1AFS1500-1FGG256
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →M1AFS250-FG256 Tỷ lệ tối đa & tính chất điện
| Manufacturer Part Number | M1AFS250-FG256 |
| Family | Fusion (M1 series, ARM Cortex-M1) |
| System Gates | 250000 |
| Logic Cells | 6144 |
| Embedded Processor | ARM Cortex-M1 |
| Tần số xung maksimum | 350 MHz |
| Number of I/O | 114 |
| RAM Bits | 36864 |
| Process Technology | 130 nm |
| Core Supply Voltage | 1.5 V |
| Configuration Memory | Flash (nonvolatile) |
| Khoảng nhiệt độ hoạt động | 0C to +70C |
| Hộp / Vỏ | 256-FBGA (256-LBGA), 1.00 mm pitch |
| Kiểu lắp đặt | SMD/SMT |
| Packaging | Tray |
| Trạng thái RoHS | RoHS Non-Compliant (contains lead) |
| Lead Free Status | Contains Lead |
| Series | M1AFS250 |
Hướng dẫn cấu hình chân M1AFS250-FG256 256-fbga (256-lbga), 1.00 mm pitch
Cấu hình chân cho M1AFS250-FG256 (256-fbga (256-lbga), 1.00 mm pitch gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho M1AFS250-FG256.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
M1AFS250-FG256 phù hợp cho 6 Áp dụngs: Smart Power and Motor Control, Industrial Automation and Control Panels, Portable and Battery-Powered Instrumentation, Embedded System-on-Chip Designs (Cortex-M1 + Logic), Test and Measurement Equipment, Legacy Long-Lifecycle System Maintenance.
Smart Power and Motor Control
The M1AFS250-FG256 fits smart power and motor-control designs because its monolithic Fusion die combines configurable analog monitoring with flash-based logic and an ARM Cortex-M1 processor running at up to 350 MHz. PWM generation, dead-time insertion, and closed-loop control algorithms execute in fabric and processor without a discrete MCU, while the analog block supervises bus voltage and phase current without external ADCs. With 114 user I/O, gate-driver and encoder interfaces connect directly. Placing supervisory sampling in the FPGA fabric removes ADC latency from the control loop, enabling faster fault shutdown than MCU-only designs. Designers should budget core power at 1.5V based on fabric utilization and clock rate, and should note the FG256 is leaded, so industrial RoHS-exempt status must be confirmed or the FGG256 drop-in selected.
Được đề xuất
Industrial Automation and Control Panels
In industrial automation, the M1AFS250-FG256 consolidates sequencing logic, sensor aggregation, and supervisory control in one 256-FBGA device. The flash-based fabric configures instantly at power-up without an external boot PROM, reducing board components and improving field reliability, while the Cortex-M1 handles protocol handling such as MODBUS-style polling or custom state machines. The commercial 0C to +70C range suits cabinet-mounted controllers; for floor-level hardware select the industrial-temperature M1AFS250-2FG256I on the same footprint. The nonvolatile flash fabric also resists configuration corruption in noisy EMC environments typical of factory floors, an advantage over SRAM FPGAs. Designers should implement the 1.5V core rail with proper sequencing per the Microchip Fusion datasheet and reserve I/O banks for isolated field interfaces.
Được đề xuất
Portable and Battery-Powered Instrumentation
The M1AFS250-FG256 suits portable instrumentation where single-chip integration minimizes size and quiescent power. The 130 nm flash process draws essentially zero static configuration power compared to SRAM FPGAs, and the 1.5V core supply supports efficient DC-DC generation from Li-ion inputs. The integrated configurable analog replaces discrete amplifiers and ADCs for slow-speed measurement channels, while the Cortex-M1 at up to 350 MHz performs scaling, calibration, and display updates. Nonvolatile instant-on configuration lets the instrument be ready in milliseconds after wake, important for triggered measurements. Because the commercial temperature part tops out at +70C, handheld enclosures with heat concentration should be thermally evaluated. Estimate: core dissipation scales with clock frequency and utilization, so keep unused fabric idle to extend battery life.
Được đề xuất
Embedded System-on-Chip Designs (Cortex-M1 + Logic)
For embedded designs needing both a processor and custom logic, the M1AFS250-FG256 eliminates the discrete MCU plus FPGA pairing. The ARM Cortex-M1 soft core runs at up to 350 MHz on the same die as 6,144 logic cells and 36,864 RAM bits, communicating with fabric through on-chip interfaces with far lower latency than an external bus. Software development uses standard ARM toolchains while hardware is built in Microchip Libero SoC, allowing concurrent firmware and RTL work. The monolithic approach also removes board-level trace timing risk between MCU and FPGA and cuts BOM count. Memory-constrained designs should verify the 36,864 bits of block RAM suffices for buffering; otherwise select the pin-compatible M1AFS1500-FG256, which multiplies memory and logic resources on the identical PCB land pattern.
Được đề xuất
Test and Measurement Equipment
Bench and embedded test instruments benefit from the M1AFS250-FG256's instant-on flash configuration and mixed-signal integration. The FPGA fabric implements trigger logic, timing generators, and interface bridges (UART, SPI, parallel buses) with deterministic timing, while the Cortex-M1 manages command parsing and housekeeping. The configurable analog block provides monitoring channels for supply and signal supervision. In lab instruments, the 0C to +70C commercial range is typically adequate. Integration of clock generation and management circuitry on-chip simplifies jitter budgeting for measurement timing chains compared to multi-chip clock trees. Designers should place high-speed I/O banks near board edge connectors in the FG256 footprint to minimize stub lengths, and decouple the 1.5V core with low-ESR ceramics per the Microchip power design guidance.
Được đề xuất
Legacy Long-Lifecycle System Maintenance
For maintaining legacy systems originally built around Actel Fusion silicon, the M1AFS250-FG256 provides continuity since Microchip (formerly Microsemi) continues the product line with unchanged silicon and Libero design support. The nonvolatile flash configuration means original bitstreams load identically on new silicon, avoiding SRAM-FPGA boot issues in fielded hardware. When regulatory requirements tighten, M1AFS250-FGG256 is the pin-compatible lead-free drop-in, and when capacity must grow, M1AFS600 and M1AFS1500 in FG256 packages reuse the same PCB footprint per the manufacturer product brief, which states Fusion devices in the same package are pin compatible (except PQ208). Procurement teams should validate speed grade and temperature suffix against the original BOM before substitution.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho M1AFS250-FG256 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | M1AFS250-FGG256 | M1AFS250-2FG256I | M1AFS600-2FG256 | M1AFS1500-1FGG256 |
|---|---|---|---|---|---|
| Package | 256-FBGA (1.00 mm pitch) | 256-FBGA - same footprint | 256-FBGA - same footprint | 256-FBGA - same footprint | 256-FBGA - same footprint |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| System Gates | 250,000 | 250,000 | 250,000 | 600,000 | 1,500,000 |
| Embedded Processor | ARM Cortex-M1 | ARM Cortex-M1 | ARM Cortex-M1 | ARM Cortex-M1 | ARM Cortex-M1 |
| Core Supply Voltage | 1.5 V | 1.5 V | 1.5 V | 1.5 V | 1.5 V |
Bảo phân biệt quan trọng
- RoHS-compliant drop-in available on identical footprint (vsM1AFS250-FGG256)
- Lowest cost and power in the pin-compatible FG256 family (vsM1AFS600-2FG256)
- Commercial-only temperature range (vsM1AFS250-2FG256I)
Ghi chú thiết kế
Supply the M1AFS250-FG256 core with a regulated 1.5V rail; I/O and analog banks use additional rails per the Microchip Fusion datasheet power architecture. Follow the datasheet power-up sequencing order strictly - incorrect rail sequencing can latch the I/O or misconfigure the analog block. Decouple each supply pin pair with low-ESR ceramic capacitors placed close to the 256-FBGA balls, and use a solid ground return through the BGA via field. Estimated: core dissipation scales with clock frequency and fabric utilization - budget using Libero SoC power analysis, not rule-of-thumb numbers.
The FG256 is a 1.00 mm pitch 256-ball BGA, requiring controlled-impedance multilayer PCB with via-in-pad or dog-bone fanout. Keep breakout length short and uniform to preserve signal integrity on the 114 user I/O. Reserve continuous copper under the package for the analog ground quadrant - the Fusion analog block shares the die and is sensitive to digital return currents. Do not route fast switching signals across the analog quadrant's escape fanout. Reference the Microchip Fusion board layout guidelines before finalizing the land pattern, especially if planning future migration to M1AFS600/M1AFS1500 FG256 devices.
The most frequent procurement pitfall: the FG256 ordering code is RoHS non-compliant and contains lead, restricting new EU/REACH-bound designs - specify M1AFS250-FGG256 (identical footprint) unless the application is RoHS-exempt. Second pitfall: temperature suffix. FG256 alone is 0C to +70C commercial; field-deployed hardware needs the -I industrial variants such as M1AFS250-2FG256I. Third, when migrating to M1AFS600/1500 FG256 parts, remember pin-compatibility does not guarantee identical per-pin analog configuration - re-verify analog assignments in Libero SoC before respin-free migration.
Thông tin tuân thủ
Per digichip.com datasheet data: Lead Free Status - Contains Lead; RoHS Status - RoHS Non-Compliant. The M1AFS250-FGG256 variant is the Green, lead-free alternative. REACH and conflict-minerals status not stated in provided data.
