MAX202ECSE+TG068 2/2 RS-232 Transceiver | Analog Devices
MPN: MAX202ECSE+TG068 ✓ Hoạt độngMAX202ECSE+TG068 Tóm tắt
An RS-232 transceiver is an interface IC that combines differential signal translation between single-ended logic and RS-232 levels with the electrical isolation required at a communications port. Within the product hierarchy, MAX202ECSE+TG068 is a line driver and receiver, an interface transceiver, and ultimately a semiconductor designed for reliable point-to-point data transmission.
The primary electrical features include two transmit channels, two receive channels, operation from a single 4.5 V to 5.5 V supply, and 15 kV ESD protection. The MAX202E family also emphasizes low power consumption and high-speed transmission, making it suitable for embedded control systems, industrial equipment, and legacy data ports that must exchange serial data over longer cables than logic-level interfaces permit.
The MAX202E implementation includes the charge-pump circuitry required to generate RS-232 transmit voltage levels. This integrated approach avoids external voltage-conversion components and simplifies board layout. Nevertheless, system designers must still account for the non-isolated nature of the interface, provide suitable bypass capacitance, and connect unused driver inputs and receiver outputs to defined logic levels where required.
Typical applications include RS-232 links in industrial controllers, test equipment, point-of-sale terminals, service interfaces, and embedded systems. The two-driver and two-receiver arrangement supports full-duplex communication when two transmitters and two receivers are connected across a communications link. Its 16-SOIC package also allows reuse of the same board footprint across several MAX202 family ordering variants.
For PCB design, place the device close to the connector and route protected and unprotected circuitry according to the manufacturer’s pin-description table and application circuit. Keep switching-node and high-energy transient paths away from receiver inputs, provide the required local bypass capacitors, and verify that the selected cable, connector, and grounding strategy meet the intended RS-232 application.
This page organizes the available ordering information, package details, functional characteristics, practical applications, and same-family drop-in alternatives into an engineering-focused guide for selecting and implementing the MAX202ECSE+TG068.
Bộ thay thế dễ dàng lắp đặt cho MAX202ECSE+TG068 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX202ECSE+TG068 (cùng hình factor và footprint) — khác nhau ở Package, Transceiver Configuration, ESD Protection, Supply Voltage, Charge Pump.
MAX202ECSE+
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX202ESE+
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX202ESE+T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX202ESE-TG068
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX202ECSE+T
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX202ECSE+TG068 Thông số kỹ thuật
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Transceiver Configuration | 2/2 full RS-232 |
| Supported Protocol | RS-232 |
| Supply Voltage Range | 4.5 V to 5.5 V |
| ESD Protection | 15 kV |
| Hộp | 16-SOIC, 0.154 in x 3.90 mm width |
| Packaging | Tape and reel |
| Kiểu lắp đặt | Surface mount |
| Số lượng chân | 16 |
| Driver Output Count | 2 |
| Receiver Input Count | 2 |
| Communication Mode | Full duplex |
| Operating Voltage | 4.5 V to 5.5 V |
Hướng dẫn cấu hình chân MAX202ECSE+TG068 16-soic, 0.154 in x 3.90 mm width
Cấu hình chân cho MAX202ECSE+TG068 (16-soic, 0.154 in x 3.90 mm width gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX202ECSE+TG068.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX202ECSE+TG068 phù hợp cho 6 Áp dụngs: Industrial Controller RS-232 Port, Test and Measurement Equipment, Embedded Service Interface, Point-of-Sale Terminal, Network Equipment Management Port, Low-Voltage Data Acquisition Unit.
Industrial Controller RS-232 Port
The MAX202ECSE+TG068 suits an industrial controller that must communicate with legacy equipment over RS-232. Its two drivers and two receivers support a full-duplex link, while the 4.5 V to 5.5 V supply range is compatible with a conventional 5 V control rail. The 15 kV ESD protection adds an important protection layer at an exposed connector boundary. Place the transceiver near the connector, route the protected interface through the driver and receiver pins, and keep unrelated switching circuitry away from the interface. Verify operating temperature, isolation strategy, grounding, and cable length before approving the design.
Được đề xuất
Test and Measurement Equipment
The MAX202ECSE+TG068 is appropriate for test equipment that needs a compact, protected serial control or data port. Two RS-232 transmit channels and two receive channels support full-duplex command and response traffic, while the 16-SOIC package preserves board area. The device's stated 15 kV ESD protection is useful when users connect external cables, although it does not replace correct chassis grounding, surge protection, or isolation. Follow the Analog Devices application circuit for bypass capacitors and charge-pump routing, and test the complete cable, connector, and host interface under the intended switching conditions.
Được đề xuất
Embedded Service Interface
The MAX202ECSE+TG068 can provide a service connection for an embedded controller, programmable controller, or industrial embedded system. The 2/2 channel arrangement allows command output and response input on one port, while the low-power, high-speed characteristics of the MAX202E family align with compact embedded equipment. Use the 4.5 V to 5.5 V operating range to establish a robust supply design and follow the manufacturer pin table for enable and unused-pin states. Because RS-232 is not galvanically isolated, include isolation or common-mode protection when the connected equipment can sit at a different ground potential.
Được đề xuất
Point-of-Sale Terminal
A point-of-sale terminal or peripheral can use the MAX202ECSE+TG068 for a two-channel full-duplex RS-232 connection to a printer, scanner, or customer display interface. The integrated drivers and receivers reduce the number of discrete interface components, while the 16-SOIC package supports automated board assembly. The 15 kV ESD rating is particularly relevant around cables that users may connect and disconnect. Position the transceiver near the connector, maintain the recommended bypass layout, and route chassis or surge currents away from logic ground. Confirm signal levels, baud rate, and cable length against the connected peripheral specification.
Được đề xuất
Network Equipment Management Port
The MAX202ECSE+TG068 can implement an RS-232 management or console port on network and communications equipment. The two transmit and two receive channels support full-duplex console traffic, and the single 4.5 V to 5.5 V supply range simplifies connection to a 5 V equipment rail. The integrated charge-pump function allows the transceiver to generate RS-232 levels without external level-shifting components. Position the IC near the serial connector and apply the manufacturer's bypass and routing recommendations. Use a common-mode solution when the console host is electrically isolated or connected through a long cable.
Được đề xuất
Low-Voltage Data Acquisition Unit
The MAX202ECSE+TG068 can serve as the host-side RS-232 interface in a low-voltage data-acquisition unit. A 4.5 V to 5.5 V operating range fits regulated 5 V systems, and the two-driver, two-receiver arrangement accommodates bidirectional commands and measurements. Its 15 kV ESD protection is valuable when the unit is used in a laboratory or industrial setting with frequently connected cables. Follow the MAX202E application circuit for bypass capacitors and keep the interface return path within the equipment grounding design. Validate the maximum data rate, input thresholds, and cable length before selecting it for a particular acquisition protocol.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX202ECSE+TG068 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX202ECSE+ | MAX202ESE+ | MAX202ESE+T | MAX202ESE-TG068 | MAX202ECSE+T |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Drivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Protocol | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 |
| ESD Protection | 15 kV | 15 kV | 15 kV | 15 kV | 15 kV | 15 kV |
| Communication Mode | Full duplex | Full duplex | Full duplex | Full duplex | Full duplex | Full duplex |
Bảo phân biệt quan trọng
- Exact TG068 tape-and-reel ordering configuration (vsMAX202ESE-TG068)
- Two-channel full-duplex RS-232 interface (vsMAX202ECSE+)
- Consistent 16-SOIC footprint within the MAX202E family (vsMAX202ESE+T)
Ghi chú thiết kế
Follow the Analog Devices MAX202E application circuit for input and output bypass-capacitor placement, and keep the device close to the RS-232 connector. Separate connector-side transient paths from sensitive logic and clock routing. The package's exposed charge-pump and interface functions require careful grounding, so follow the manufacturer footprint and pin-description table rather than substituting a generic SOIC-16 land pattern without checking exposed-pad and lead details.
Do not assume the E, C, +T, or TG068 suffix has no functional consequence. Confirm lead finish, temperature grade, packing method, and orderable status in the Analog Devices ordering table before approving a substitution. Unused driver inputs and receiver outputs should be assigned definite logic states according to the manufacturer guidance, and the 4.5 V to 5.5 V supply range must be maintained during normal operation and cable transients.
RS-232 is a single-ended interface, so ground offsets and cable transients can affect receiver reliability even when the IC provides 15 kV ESD protection. Use a controlled return path, appropriate connector grounding, and system-level surge or isolation measures where required. Place the transceiver near the connector and avoid sharing high-current return paths between the interface and sensitive logic. Validate the completed assembly against the intended cable length and grounding topology.
Thông tin tuân thủ
The MAX202 family is intended for RS-232 and V.28 communications. No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified for the exact ordering code, so those fields remain unknown.