MAX232ECPW - 250kbps RS-232 Transceiver | Texas Instruments
MPN: MAX232ECPW ✓ Hoạt độngMAX232ECPW Tóm tắt
An RS-232 transceiver is an interface IC that connects low-voltage TTL or CMOS logic to the bipolar voltage levels used by RS-232 equipment. The driver channels convert logic signals into RS-232 output levels, while the receiver channels convert incoming RS-232 signals into logic-compatible levels. A MAX232E-family device also contains a charge-pump voltage generator, allowing bipolar RS-232 levels to be produced from a single 5V supply.
The MAX232ECPW combines two transmit channels, two receive channels, and electrostatic-discharge protection in one compact 16-TSSOP package. Its stated 250kbps rate suits short-distance point-to-point serial links, including industrial-control equipment, data-acquisition systems, service interfaces, and legacy computer peripherals. The integrated protection improves robustness in connector-adjacent circuits where electrostatic discharge is a realistic concern.
Technically, the MAX232ECPW is designed for a single 5V supply and combines its charge-pump circuitry, drivers, and receivers in one interface device. The dual-driver and dual-receiver arrangement supports two independent RS-232 directions on a point-to-point link. Its 250kbps maximum signaling rate is substantially faster than conventional asynchronous RS-232 links, although cable length, capacitance, grounding, and driver loading still determine achievable communication distance.
Typical uses include programmable-logic-controller service ports, industrial serial adapters, instrumentation control links, embedded-system debug connections, and communications between equipment with legacy DB9 or equivalent RS-232 ports. The MAX232ECPW is particularly appropriate where a compact surface-mount implementation and protected RS-232 line interface are required without a separate external protection network.
PCB design should follow the capacitor and charge-pump requirements in the manufacturer datasheet, because the voltage generator depends on correctly sized charge-pump capacitors. Keep the RS-232 connector-side traces away from sensitive logic, provide a low-impedance ground reference, and place input and charge-pump capacitors close to their associated pins.
This product page combines the MAX232ECPW electrical characteristics, package information, compatible alternatives, application guidance, and practical design notes to support faster component selection and PCB implementation.
Bộ thay thế dễ dàng lắp đặt cho MAX232ECPW — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX232ECPW (cùng hình factor và footprint) — khác nhau ở Supply Voltage Range, ESD Protection, Maximum Data Rate, Product Type.
MAX232EIPWR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX3232ECPW
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX3232EIPWRQ1
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX232AEEPE
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TRS232EIPWR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX232ECPW Thông số kỹ thuật
| Product Type | RS-232 transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Channel Configuration | 2/2 full RS-232 transceiver |
| Supply Voltage Range | 4.5V to 5.5V |
| Nominal Supply Voltage | 5V |
| Maximum Data Rate | 250kbps |
| ESD Protection | IEC 61000-4-2 |
| Logic Compatibility | 5V TTL/CMOS |
| RS-232 Standard Level | TIA/EIA-232-F |
| Hộp | 16-pin TSSOP |
| Kiểu lắp đặt | Surface mount |
| Driver Output Type | RS-232 bipolar line driver |
| Receiver Output Type | TTL/CMOS logic receiver |
| Voltage Generation | Single 5V supply with capacitive voltage generator |
Hướng dẫn cấu hình chân MAX232ECPW 16-pin tssop
Cấu hình chân cho MAX232ECPW (16-pin tssop gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX232ECPW.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX232ECPW phù hợp cho 6 Áp dụngs: Programmable Logic Controller Service Port, Industrial Data Acquisition Equipment, Embedded System Debug Interface, Legacy Computer Peripheral Connection, Instrumentation Control and Service Link, Industrial Networking Gateway.
Programmable Logic Controller Service Port
The MAX232ECPW fits legacy PLC service ports because its two drivers and two receivers provide a complete point-to-point RS-232 interface from a single 5V rail. Its 250kbps maximum signaling rate is suitable for configuration downloads, status exchange, and short diagnostic sessions. IEC 61000-4-2 protection adds useful resilience where the serial connector is exposed to electrostatic discharge. The 16-pin TSSOP package also keeps the interface compact enough for space-constrained controller boards.
Được đề xuất
Industrial Data Acquisition Equipment
The MAX232ECPW can connect laboratory and industrial data-acquisition equipment to a legacy RS-232 controller. Two transmit and two receive channels support bidirectional command and measurement traffic, while the 250kbps rate accommodates moderate-rate instrument data. Operating from 4.5V to 5.5V simplifies integration with conventional 5V logic. Its documented IEC 61000-4-2 protection is especially useful in industrial environments where exposed cables and connector contacts can receive electrostatic discharge.
Được đề xuất
Embedded System Debug Interface
The MAX232ECPW is useful for a legacy debug or configuration interface because it translates between 5V TTL or CMOS logic and RS-232 line levels. A pair of driver and receiver channels allows command transmission and status reception through one compact device. The 250kbps signaling limit supports firmware logs, bootloader messages, and diagnostic commands. IEC 61000-4-2 protection helps protect the interface when the cable is connected to a user-accessible service connector.
Được đề xuất
Legacy Computer Peripheral Connection
The MAX232ECPW provides a modern surface-mount bridge for legacy DB9-style RS-232 ports on industrial computers, test systems, and service equipment. Its dual-channel arrangement is sufficient for transmit, receive, and hardware-flow-control signals commonly found on RS-232 links. The 5V supply range matches many embedded and legacy interface designs, while the TSSOP package reduces board area compared with older through-hole transceivers. Ensure the connector's signal-to-ground arrangement and cable length match the application.
Được đề xuất
Instrumentation Control and Service Link
The MAX232ECPW can serve as the service communications path in programmable instrumentation and test equipment. Its 250kbps rate is suitable for commands, calibration data, and periodic status reporting, while two drivers and two receivers support a standard bidirectional console connection. The single 5V architecture reduces the number of rails required around legacy serial hardware. IEC 61000-4-2 protection improves interface robustness when users connect service leads to external equipment in laboratories or production areas.
Được đề xuất
Industrial Networking Gateway
The MAX232ECPW can provide the legacy serial port on a gateway that bridges older equipment to a modern network. Bidirectional RS-232 communication allows the gateway to exchange configuration commands and telemetry with controllers that lack Ethernet connectivity. The 250kbps data rate suits supervisory traffic rather than bulk data transfer. Its 16-pin TSSOP footprint and integrated ESD protection make it practical for compact industrial interface cards, subject to proper grounding and cable-side surge protection.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX232ECPW — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX232EIPWR | MAX3232ECPW | MAX3232EIPWR | MAX232AEEPE | TRS232EIPWR |
|---|---|---|---|---|---|---|
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP candidate | 16-pin TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver |
| Number of Drivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Nominal Supply Voltage | 5V | 5V | 5V | 5V | 5V | 5V |
| Maximum Data Rate | 250kbps | 250kbps | 250kbps | 250kbps | 250kbps | 250kbps |
Bảo phân biệt quan trọng
- Documented ESD protection in a compact dual-channel interface (vsTRS232EIPWR)
- High data rate for a single-supply RS-232 transceiver (vsMAX232EIPWR)
- Direct same-footprint sourcing family (vsMAX3232ECPW)
Ghi chú thiết kế
Place the charge-pump capacitors and supply-decoupling capacitor close to their specified pins, keeping the high-current charge-pump loop compact. The MAX232ECPW generates bipolar RS-232 voltage from its 5V supply through switched-capacitor action, so long capacitor traces can increase switching noise and reduce available voltage margin. Follow the manufacturer datasheet capacitor values and component tolerances rather than substituting generic capacitors solely by capacitance rating.
Do not treat the 250kbps rating as a guaranteed communication distance. RS-232 cable capacitance, driver loading, connector construction, grounding, and common-mode noise can reduce practical reliability at higher rates. Test the complete cable and equipment combination under worst-case noise conditions, and avoid relying on software flow control as a substitute for correctly routed handshake signals.
Keep connector-side RS-232 driver and receiver traces physically separated from sensitive analog or high-speed digital nets, and provide a continuous ground reference adjacent to the interface route. Although the device includes IEC 61000-4-2 protection, the protection network is not a substitute for external surge protection where cables extend beyond the enclosure or encounter larger industrial transients.
Thông tin tuân thủ
IEC 61000-4-2 protection is documented for the device. Other environmental and material-compliance claims were not established from the available product information and are therefore marked unknown.