MAX3232EIDWG4 - Dual RS-232 IC | Texas Instruments
MPN: MAX3232EIDWG4 ✓ Hoạt độngMAX3232EIDWG4 Tóm tắt
An RS-232 interface transceiver is a semiconductor that bridges the voltage-domain difference between digital logic and the bipolar RS-232 serial interface. The MAX3232EIDWG4 belongs to the interface IC hierarchy, where a transceiver integrates one or more line drivers and receivers with charge-pump circuitry and electrostatic-discharge protection. It is commonly placed between a microcontroller UART and an external serial connector.
Key features include two driver and two receiver channels, operation from 3 V to 5.5 V, and ±15 kV IEC ESD protection. The E suffix identifies the enhanced ESD-capable family, while the G4 ordering code denotes the green, standard industrial-temperature version associated with a −40 °C to +85 °C operating range. The 16-pin SOIC package supports conventional surface-mount assembly and is compatible with automated PCB production.
The MAX3232E uses on-chip charge-pump circuitry to generate the positive and negative voltage swings required by RS-232 without a negative supply input. This architecture allows the logic side to operate from a single 3 V to 5.5 V rail. The interface includes integrated protection for external connector signals, reducing the need for separate low-capacitance TVS devices when the board layout and routing follow the manufacturer's recommendations.
Typical applications include industrial serial controllers, test and measurement equipment, computer peripherals, point-of-sale terminals, embedded service ports, and legacy RS-232 equipment connected to modern microcontrollers. The dual-channel arrangement is useful when one system must support bidirectional communication, multiple RS-232 devices, or separate transmit and receive data paths.
PCB design should place the device near the RS-232 connector, route driver outputs and receiver inputs away from sensitive logic, and connect the charge-pump capacitors and supply-decoupling capacitor close to their specified pins. Keep unprotected external leads short and follow the datasheet's ESD layout guidance so that system-level transient performance is not limited by long copper traces.
This product page combines the exact ordering information, electrical limits, interface characteristics, package details, drop-in alternatives, comparison parameters, and practical PCB guidance needed to evaluate and implement the MAX3232EIDWG4 in a new design.
Bộ thay thế dễ dàng lắp đặt cho MAX3232EIDWG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX3232EIDWG4 (cùng hình factor và footprint) — khác nhau ở ESD Protection, Product Type, Package, Supply Voltage Range, Number of Receivers.
MAX3232EIDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232IPW
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232ECDW
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232ID
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3222CWE+
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3232EIDWG4 Thông số kỹ thuật
| Product Type | RS-232 line driver and receiver transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Logic Compatibility | CMOS/TTL logic levels |
| Supply Voltage Range | 3 V to 5.5 V |
| RS-232 Interface | Full-duplex RS-232 |
| ESD Protection | ±15 kV IEC ESD protection |
| Khoảng nhiệt độ hoạt động | −40 °C to +85 °C |
| Hộp | 16-pin SOIC |
| Package Width | 7.50 mm |
| Kiểu lắp đặt | Surface mount |
| Số lượng chân | 16 pins |
| Supply Configuration | Single 3 V to 5.5 V supply |
| Charge-Pump Architecture | Integrated dual charge-pump circuitry |
Hướng dẫn cấu hình chân MAX3232EIDWG4 7.50 mm
Cấu hình chân cho MAX3232EIDWG4 (7.50 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3232EIDWG4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3232EIDWG4 phù hợp cho 6 Áp dụngs: Industrial RS-232 Controller, Point-of-Sale Terminal Interface, Test and Measurement Equipment, Computer Peripheral Connectivity, Embedded Service Port, Legacy Equipment Upgrade.
Industrial RS-232 Controller
The MAX3232EIDWG4 fits industrial serial controllers that need a reliable logic-to-RS-232 interface at 3.3 V or 5 V. Its two drivers and two receivers support full-duplex communication, while the 3 V to 5.5 V supply range accommodates both 3.3 V microcontrollers and 5 V control logic. The specified −40 °C to +85 °C temperature range covers extended industrial conditions. Place the interface near the connector and observe the charge-pump capacitor layout from the manufacturer datasheet. Its ±15 kV IEC ESD protection adds useful margin at an exposed serial port, although the enclosure, cable, and grounding strategy remain part of the overall surge-protection design.
Được đề xuất
Point-of-Sale Terminal Interface
The MAX3232EIDWG4 is suitable for point-of-sale equipment requiring a compact RS-232 port alongside a 3.3 V processor. Two driver and receiver channels allow bidirectional service communication or connection to more than one legacy peripheral without adding separate transceiver ICs. The 16-pin SOIC package simplifies surface-mount assembly, and ±15 kV IEC ESD protection is valuable when customer-facing cables connect to external equipment. Designers should keep the RS-232 traces separated from display, Ethernet, and power-converter nodes, connect the supply bypass capacitor close to VCC, and follow the datasheet's charge-pump capacitor values and placement guidance.
Được đề xuất
Test and Measurement Equipment
The MAX3232EIDWG4 can connect a modern instrument controller to legacy RS-232 test equipment through its two-driver, two-receiver arrangement. The 3 V to 5.5 V operating range allows the interface to share either 3.3 V or 5 V control rails, and the −40 °C to +85 °C range supports use across laboratory and industrial test environments. The integrated ±15 kV IEC ESD protection is useful for frequently connected service ports. For reliable measurements, terminate the ground conductor properly, route driver and receiver nets away from sensitive analog traces, and place the external charge-pump capacitors at the pins indicated in the manufacturer application circuit.
Được đề xuất
Computer Peripheral Connectivity
The MAX3232EIDWG4 provides a compact interface for legacy computer peripherals, service consoles, and configuration ports that still use RS-232. A single 3 V to 5.5 V supply simplifies adaptation to both older 5 V systems and newer 3.3 V controllers, while the dual-channel implementation supports bidirectional command and data paths. Its 16-pin SOIC package permits placement close to the connector, which reduces susceptibility to noise picked up by long unprotected traces. Use a solid chassis or logic ground strategy, observe the datasheet's ESD layout, and avoid placing the RS-232 traces parallel to switching-converter or high-speed clock nets.
Được đề xuất
Embedded Service Port
The MAX3232EIDWG4 is appropriate for an embedded system that exposes a service or configuration port using the widely deployed RS-232 standard. Two drivers and two receivers provide flexibility for command ports, firmware download functions, and diagnostic links, and the 3 V to 5.5 V range supports common embedded processor rails. The ±15 kV IEC ESD protection helps the port withstand electrostatic discharge encountered during field servicing. Keep the connector-side routing compact, use the recommended charge-pump capacitors, provide local supply bypassing, and check that the external connector's signal and ground assignments match the device pin functions in the manufacturer datasheet.
Được đề xuất
Legacy Equipment Upgrade
The MAX3232EIDWG4 enables modern controllers to communicate with legacy RS-232 equipment without preserving obsolete logic-side supply levels. A 3.3 V controller can operate alongside the interface through the device's 3 V to 5.5 V supply range, and the dual-channel configuration can support both control and status connections. The enhanced E-family ESD rating provides ±15 kV IEC protection for exposed equipment connections. Confirm that the legacy system uses true RS-232 bipolar levels rather than RS-422, RS-485, or a proprietary serial protocol, and verify pin-level behavior before using the MAX3232EIDWG4 as a drop-in replacement.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3232EIDWG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3232EIDR | MAX3232IPW | MAX3232ECDW | MAX3232ID | MAX3222CWE+ |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Maxim Integrated |
| Package | 16-SOIC | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same |
| Product Type | Dual RS-232 transceiver | MAX3232E RS-232 transceiver | Multichannel RS-232 line driver/receiver | Multichannel RS-232 line driver/receiver | MAX3232 RS-232 transceiver | RS-232 line driver/receiver |
| Number of Pins | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Bảo phân biệt quan trọng
- Enhanced IEC ESD protection in the MAX3232E family (vsMAX3232ID)
- Direct same-family packaging alternative (vsMAX3232EIDR)
- Single supply supports both common logic rails (vsMAX3222CWE+)
Ghi chú thiết kế
Place the MAX3232EIDWG4 near the RS-232 connector and keep the driver and receiver traces short. Follow the manufacturer application circuit for the charge-pump capacitor values, connection nodes, and VCC bypass capacitor. A short return-path ground connection to the connector shield or chassis is important when the cable leaves the enclosure. Do not route RS-232 nets beneath switching regulators, crystals, high-speed clock lines, or sensitive analog inputs.
Do not substitute a MAX3232 family member based only on the 16-pin SOIC outline. Confirm every pin function, enable polarity, charge-pump node, driver output, receiver input, supply range, temperature grade, and ESD rating. The MAX3232EIDWG4 is specifically identified for ±15 kV IEC ESD protection; using a non-E variant may remove that specification even when the PCB footprint appears identical.
Treat the RS-232 connector as an electromagnetic and electrostatic-discharge entry point. Route input and output conductors away from board edges and switching nodes, use a low-impedance ground reference, and place protection or filtering components directly at the connector when additional protection is required. Keep logic-side UART traces away from the charge-pump and connector-side nets to prevent switching transients from coupling into the host controller.
Use the package pin-description table from the manufacturer datasheet for every PCB net, including the exposed relationships of the 16-pin SOIC. Maintain the specified capacitor placement and keep loop area around the charge-pump network small. Because this interface supports a 3 V to 5.5 V supply, verify that the selected bypass capacitor has adequate DC-bias derating at 3.3 V and sufficient effective capacitance for the required UART data rate.
Thông tin tuân thủ
The manufacturer datasheet identifies ±15 kV IEC ESD protection, but separate RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification statements require confirmation from the current manufacturer product documentation.