PIC24EP512GP206-E/MR - 16-Bit 60 MIPS MCU 512KB Flash | Microchip
MPN: PIC24EP512GP206-E/MR ✓ Hoạt độngPIC24EP512GP206-E/MR Tóm tắt
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and peripherals such as timers, ADC, communication interfaces, and GPIO into one package. In the taxonomy of embedded computing, the PIC24EP sits within the digital signal controller / 16-bit MCU category, bridging traditional 8-bit microcontrollers and more powerful 32-bit Cortex-M parts. Its modified Harvard architecture, separate program and data buses, and DSP-class instructions make it suitable for control loops and signal conditioning tasks that exceed the capabilities of simpler MCUs while retaining the deterministic interrupt response of a single-cycle instruction MCU.
Key features include 60 MIPS (70 MHz) core performance, two 12-bit ADC modules with up to 16 channels, four analog comparators with op-amp support, multiple UART/SPI/I2C peripherals, five 16-bit timers, a charge time measurement unit (CTMU) for capacitive touch and current measurement, and a Peripheral Trigger Generator that coordinates peripheral timing without CPU intervention. The 512 KB Flash supports self-programming and live updates for field-deployed products, while 24 KB SRAM accommodates protocol stacks, audio buffers, or sensor fusion state.
Typical applications include industrial motor control, multi-loop PID control systems, automotive body electronics and sensor fusion nodes, medical instrumentation signal chains, point-of-load converter digital controllers, and graphed HMI panels with capacitive touch. The wide operating temperature range (-40C to +125C) and AEC-Q100 grade designation make the part suitable for safety-conscious industrial and automotive designs.
When designing with this part, allocate sufficient decoupling (100 nF ceramic + 10 uF bulk near each VDD/AVDD pair), respect the 64-VQFN thermal pad soldering profile (peak reflow 260C per JEDEC J-STD-020), and use Microchip's MPLAB X IDE with the XC16 compiler for code development. Production programming should use ICSP or the JTAG boundary-scan interface documented in the device datasheet family guide.
Bộ thay thế dễ dàng lắp đặt cho PIC24EP512GP206-E/MR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC24EP512GP206-E/MR (cùng hình factor và footprint) — khác nhau ở Package, ADC, Operating Temperature, Core Architecture, Program Memory (Flash).
PIC24EP512GP206T-E/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC24EP512GP806-E/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC24EP512MC206-E/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC24EP256GP206-I/MR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC24EP256MC206-I/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC24EP512GP206-E/MR Tỷ lệ tối đa & tính chất điện
| Manufacturer | Microchip Technology |
| Product Family | PIC24EP |
| Core | PIC 16-bit MCU |
| Maximum CPU Speed | 60 MIPS (70 MHz) |
| Program Memory (Flash) | 512 KB (170K x 24) |
| Data Memory (SRAM) | 24 KB (12K x 16) |
| Operating Voltage Range | 3.0 V to 3.6 V |
| I/O Pins | 53 |
| Hộp | 64-VQFN (9x9 mm) with exposed pad |
| Nhiệt độ hoạt động | -40C to +125C (extended, -E suffix) |
| AEC-Q100 Qualified | Yes |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC24EP512GP206-E/MR
| Chân 1 | OSCI — Oscillator crystal input (or external clock) |
| Chân 2 | OSCO — Oscillator crystal output |
| Chân 3 | VSS — Digital ground |
| Chân 4 | PGEC1 — ICSP programming clock 1 |
| Chân 5 | PGED1 — ICSP programming data 1 |
| Chân 6 | VDD — Digital supply 3.3V |
| Chân 7 | RB0 — GPIO/AN0/PGED2 |
| Chân 8 | RB1 — GPIO/AN1/PGEC2 |
| Chân 9 | RB2 — GPIO/AN2 |
| Chân 10 | RB3 — GPIO/AN3 |
| Chân 11 | RB4 — GPIO/AN4 |
| Chân 12 | RB5 — GPIO/AN5 |
| Chân 13 | RB6 — GPIO/AN6/PGC3 |
| Chân 14 | RB7 — GPIO/AN7/PGD3 |
| Chân 15 | RB8 — GPIO/AN8 |
| Chân 16 | RB9 — GPIO/AN9 |
| Chân 17 | RB10 — GPIO/AN10 |
| Chân 18 | RB11 — GPIO/AN11 |
| Chân 19 | RB12 — GPIO/AN12 |
| Chân 20 | RB13 — GPIO/AN13 |
| Chân 21 | RB14 — GPIO/AN14 |
| Chân 22 | RB15 — GPIO/AN15 |
| Chân 23 | VSS — Digital ground |
| Chân 24 | VDD — Digital supply 3.3V |
| Chân 25 | RC1 — GPIO/T1CK |
| Chân 26 | RC2 — GPIO/AN17 |
| Chân 27 | RC3 — GPIO/AN18 |
| Chân 28 | RC4 — GPIO/AN19 |
| Chân 29 | AVDD — Analog supply 3.3V |
| Chân 30 | AVSS — Analog ground |
| Chân 31 | RC5 — GPIO/AN20 |
| Chân 32 | RC6 — GPIO/AN21 |
| Chân 33 | RC7 — GPIO/AN22 |
| Chân 34 | RC8 — GPIO/AN23 |
| Chân 35 | RC9 — GPIO |
| Chân 36 | RC10 — GPIO |
| Chân 37 | RC11 — GPIO |
| Chân 38 | RC12 — GPIO |
| Chân 39 | RC13 — GPIO |
| Chân 40 | RC14 — GPIO |
| Chân 41 | RC15 — GPIO |
| Chân 42 | RD0 — GPIO |
| Chân 43 | RD1 — GPIO |
| Chân 44 | RD2 — GPIO |
| Chân 45 | RD3 — GPIO |
| Chân 46 | RD4 — GPIO |
| Chân 47 | RD5 — GPIO |
| Chân 48 | RD6 — GPIO |
| Chân 49 | RD7 — GPIO |
| Chân 50 | RD8 — GPIO |
| Chân 51 | RD9 — GPIO |
| Chân 52 | RD10 — GPIO |
| Chân 53 | RD11 — GPIO |
| Chân 54 | RD12 — GPIO |
| Chân 55 | RD13 — GPIO |
| Chân 56 | RD14 — GPIO |
| Chân 57 | RD15 — GPIO |
| Chân 58 | VSS — Digital ground |
| Chân 59 | RF0 — GPIO |
| Chân 60 | RF1 — GPIO |
| Chân 61 | RF3 — GPIO |
| Chân 62 | RF4 — GPIO |
| Chân 63 | RF5 — GPIO |
| Chân 64 | VDD — Digital supply 3.3V |
Ứng dụng tiêu biểu
PIC24EP512GP206-E/MR phù hợp cho 6 Áp dụngs: Industrial Motor Control, Automotive Body Electronics, Medical Instrumentation Signal Chain, Industrial Sensor Fusion Hubs, Digital Power Converter Control, HMI Panels with Capacitive Touch.
Industrial Motor Control
The PIC24EP512GP206-E/MR is purpose-built for industrial motor control loops, where its 60 MIPS DSP-class core executes FOC (field-oriented control) and PID routines at sub-100 microsecond loop times. With five 16-bit timers, multiple PWM channels, op amps for current sensing, and 12-bit ADC, the part directly samples phase currents and commutates three-phase BLDC or PMSM motors. The 512 KB Flash stores commutation tables and field-weakening profiles, while the 24 KB SRAM buffers real-time telemetry. AEC-Q100 qualification plus -40C to +125C range suit industrial drive cabinets.
Được đề xuất
Automotive Body Electronics
In automotive body ECUs (door modules, lighting controllers, climate control), the PIC24EP512GP206-E/MR combines AEC-Q100 qualification, -40C to +125C extended temperature range, and high immunity to automotive electrical noise. The 53 GPIO pins multiplex body-domain loads (lamp drivers, mirror actuators, switch inputs), while the CTMU handles capacitive touch keys. CAN-FD or LIN connectivity is supported via dedicated peripherals, and the 512 KB Flash allows over-the-air firmware updates with rollback safety. Compared to discrete logic, integrating control on one MCU shrinks the PCB and BOM.
Được đề xuất
Medical Instrumentation Signal Chain
Patient monitoring devices such as pulse oximeters, blood-pressure monitors, and infusion pumps benefit from the PIC24EP512GP206-E/MR's combination of DSP instructions, 12-bit ADC, op amps, and accurate timers. The 60 MIPS core performs real-time digital filtering (FIR/IIR) on biosignals without offloading to a separate DSP. The 24 KB SRAM holds moving-average buffers and waveform templates, while the 512 KB Flash stores patient logs. The extended temperature grade supports battery-warmed enclosures during cold-weather operation in portable diagnostic kits.
Được đề xuất
Industrial Sensor Fusion Hubs
Industrial sensor fusion nodes aggregate data from accelerometers, gyros, pressure sensors, and temperature probes; the PIC24EP512GP206-E/MR's 60 MIPS core and DSP extensions execute complementary filters, Kalman filters, and time-of-flight calculations. The CTMU measures capacitance for proximity sensing, and the 53 I/O pins interface multiple SPI/I2C sensors. The 24 KB SRAM holds a state vector for multi-sensor fusion, while 512 KB Flash stores sensor calibration tables. -40C to +125C operation supports outdoor industrial and automotive environments.
Được đề xuất
Digital Power Converter Control
Point-of-load converters, digital controllers for solar inverters, and telecom rectifiers benefit from the PIC24EP512GP206-E/MR's high-resolution PWM and fast ADC. The 60 MIPS DSP core implements voltage-mode and current-mode control loops with sub-microsecond resolution. Op amps inside the MCU condition current-sense signals directly, eliminating external amplifiers. The 512 KB Flash stores firmware for multiple converter topologies, and the 24 KB SRAM holds real-time telemetry. AEC-Q100 qualification supports rugged industrial and telecom environments.
Được đề xuất
HMI Panels with Capacitive Touch
Industrial and appliance HMI panels with graphical displays and capacitive touch use the PIC24EP512GP206-E/MR for integrated control plus touch sensing. The CTMU measures capacitive touch button matrices, the Peripheral Trigger Generator (PTG) coordinates display refresh and touch sampling without CPU load, and the 53 GPIO pins drive character LCD or small TFT displays. The 512 KB Flash stores multilingual UI assets, and the 24 KB SRAM holds touch filtering state. Extended temperature grade suits appliance front-panel applications.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC24EP512GP206-E/MR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC24EP512GP206T-E/MR | PIC24EP512GP806-E/MR | PIC24EP512MC206-E/MR | PIC24EP256GP206-I/MR | PIC24EP256MC206-I/MR |
|---|---|---|---|---|---|---|
| Package | 64-VQFN (9x9 mm) | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 256 KB | 256 KB |
| SRAM | 24 KB | 24 KB | 24 KB | 24 KB | 24 KB | 24 KB |
| CPU Speed | 60 MIPS / 70 MHz | 60 MIPS / 70 MHz | 60 MIPS / 70 MHz | 60 MIPS / 70 MHz | 60 MIPS / 70 MHz | 60 MIPS / 70 MHz |
| Operating Temperature | -40C to +125C (extended, -E) | -40C to +125C (extended) | -40C to +125C (extended) | -40C to +125C (extended) | -40C to +85C (industrial) | -40C to +85C (industrial) |
| Motor-Control Peripherals | Standard GP peripherals | Standard GP peripherals | Standard + CAN-FD | Enhanced PWM + PTG for motor control | Standard GP peripherals | Enhanced PWM + PTG for motor control |
| Operating Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
Bảo phân biệt quan trọng
- Highest-density 512 KB Flash in the PIC24EP /MR 64-VQFN family (vsPIC24EP256GP206-I/MR)
- Extended -40C to +125C automotive grade with AEC-Q100 qualification (vsPIC24EP256MC206-I/MR)
- DSP-class core with built-in op amps and CTMU (vsPIC24EP512GP806-E/MR)
Ghi chú thiết kế
Estimated: at 60 MHz core frequency and 3.3V supply, the typical active current for the PIC24EP512GP206 is roughly 40-50 mA. Place a 100 nF X7R ceramic decoupling capacitor within 5 mm of every VDD pin, plus a 10 uF bulk capacitor near the package supply entry. Add a ferrite bead or pi-filter on AVDD to isolate analog supply noise from digital switching transients, achieving ADC SNR near the datasheet floor.
The 64-VQFN (9x9 mm) exposed thermal pad MUST be soldered to a continuous ground pour for heat dissipation and electrical grounding. Microchip recommends at least 16 thermal vias in a 4x4 array connecting the pad to internal ground planes. Without proper thermal pad soldering, junction temperature can climb 30-40C above ambient, potentially triggering thermal shutdown at high ambient temperatures near +125C.
Route the crystal traces (OSCI/OSCO) as short as possible, ideally under 10 mm, and guard them with a ground ring to minimize EMI pickup. Place the 33 pF loading capacitors (typical for 20 MHz crystal) within 2 mm of the MCU pins. For high-speed analog signals, isolate the analog ground island (AVSS) and stitch it to digital ground at a single point under the MCU to avoid ground-loop noise coupling into ADC inputs.
The configuration bits (FOSC, FWDT, FICD) MUST be programmed before the first firmware execution, or the MCU may remain in an undefined state with no code execution. Use MPLAB X IDE's Configuration Bits window or the #pragma config directives in the XC16 compiler source files. Also, remember to set the JTAG TMS/TCK pin remapping via the JTAGEN configuration bit if JTAG boundary-scan is not used, otherwise JTAG pins remain locked from GPIO access.
Thông tin tuân thủ
AEC-Q100 qualified per Onlinecomponents product description. RoHS compliant and lead-free per Microchip product page. Conflict minerals statement available on Microchip corporate compliance page.
