TUSB212RWBT - USB 2.0 HS Signal Conditioner | Texas Instruments
MPN: TUSB212RWBT ✓ Hoạt độngTUSB212RWBT Tóm tắt
A USB signal conditioner is an interface IC placed within a USB data path to improve signal integrity without changing the underlying USB protocol. Its hierarchy is USB interface device, signal-processing interface IC, and interface IC. The TUSB212 specifically targets USB 2.0 channels in which connector launches, PCB traces, cables, or intervening devices have introduced bandwidth-related distortion. The conditioner supports USB 2.0, OTG 2.0, and Battery Charger 1.2 environments as identified by Texas Instruments.
The principal features include programmable AC boost, programmable DC boost, pin-strap or I2C configuration, and selectable gain. According to the manufacturer product page, the device supports channels up to 5 meters before the conditioning point or 2 meters after it. It also handles D1P/M and D2P/M interchangeably, is agnostic to host or device roles, and maintains compatibility across Low-Speed, Full-Speed, and High-Speed signals.
Technically, the TUSB212 applies frequency-dependent correction intended to counter channel loss and intersymbol interference. AC boost controls the high-frequency correction applied to the data waveform, while DC boost adjusts the low-frequency transition baseline. Four selectable AC boost settings are described by Texas Instruments, and the I2C or pin-strap interface allows implementation choices to suit board constraints. The design is intended to preserve Low-Speed and Full-Speed characteristics while compensating High-Speed signals.
Typical applications include USB hubs, host controllers, peripheral ports, cable assemblies, docking systems, and test equipment with degraded or lossy channels. The interchangeable D1P/M and D2P/M interfaces simplify symmetrical USB routing, while the compact 12-X2QFN package supports space-constrained portable and industrial designs. The I2C configuration option also permits controlled adjustments where fixed pin straps are insufficient.
Designers should place the conditioner close to the channel impairment boundary and confirm the supported pre-channel or post-channel distance. USB differential routing must preserve controlled impedance and minimize stubs, while the I2C and configuration pins require appropriate pull networks. Verify the selected boost setting with compliance masks, eye diagrams, and worst-case cable and connector combinations rather than relying on nominal channel length alone.
Bộ thay thế dễ dàng lắp đặt cho TUSB212RWBT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TUSB212RWBT (cùng hình factor và footprint) — khác nhau ở Package.
TUSB212RWBR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TUSB212RWBT Thông số kỹ thuật
| Product Type | USB 2.0 high-speed signal conditioner |
| USB Version | USB 2.0 |
| Supported USB Speeds | Low-Speed, Full-Speed, and High-Speed |
| Compatibility | USB 2.0, OTG 2.0, and BC 1.2 |
| Maximum Pre-Channel Length | 5 m |
| Maximum Post-Channel Length | 2 m |
| AC Boost Configuration | Four selectable settings |
| Configuration Interface | Pin strap or I2C |
| Differential Pair Handling | D1P/M and D2P/M interchangeable |
| Host Device Role | Host and device agnostic |
| Gain Architecture | Selectable gain with daisy-chain support |
| Correction Function | Intersymbol interference compensation |
| Hộp | 12-X2QFN |
| Package Dimensions | 1.6 mm x 1.6 mm |
| Kiểu lắp đặt | Surface mount |
| Trạng thái RoHS | Compliant |
| Trạng thái vòng đời | Active |
Hướng dẫn cấu hình chân TUSB212RWBT 1.6 mm x 1.6 mm
Cấu hình chân cho TUSB212RWBT (1.6 mm x 1.6 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho TUSB212RWBT.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TUSB212RWBT phù hợp cho 6 Áp dụngs: USB 2.0 Hub Signal Conditioning, USB Docking Station Interconnect, Portable USB-C to USB-A Adapter, USB Test and Measurement Fixture, Industrial USB Gateway, USB Host Expansion Card.
USB 2.0 Hub Signal Conditioning
The TUSB212RWBT fits between a USB 2.0 hub downstream port and a loss-prone interconnect when High-Speed eye margin has degraded. Its four selectable AC boost settings, programmable DC boost, and support for Low-Speed, Full-Speed, and High-Speed signaling allow one device to serve mixed-speed ports without intentionally changing slower traffic. Position the conditioner near the impairment boundary, retain controlled differential impedance, and verify each boost setting with eye diagrams. The stated 5-meter pre-channel and 2-meter post-channel limits must be treated as maximum design constraints rather than guaranteed margin in every cable and connector combination.
Được đề xuất
USB Docking Station Interconnect
A docking station often combines long internal traces, connector launches, and external cable transitions that can degrade USB 2.0 High-Speed signals. The TUSB212RWBT provides programmable AC and DC boost to compensate for that channel, while its interchangeable D1P/M and D2P/M interfaces simplify polarity-aware routing. Use pin straps for a fixed, validated setting or I2C when firmware needs to adjust compensation. Confirm compliance at the longest supported post-channel distance of 2 meters and test combinations of dock cable, display adapters, and peripheral loads rather than relying on a nominal cable-length figure.
Được đề xuất
Portable USB-C to USB-A Adapter
Compact adapters can place a USB 2.0 High-Speed channel across a PCB transition between connector types, increasing insertion-loss and impedance-discontinuity risk. The TUSB212RWBT’s 12-X2QFN package measures 1.6 mm by 1.6 mm, allowing signal repair close to the transition without dominating a small board. Its Low-Speed and Full-Speed agnostic behavior preserves compatibility with attached accessories. Designers should maintain uniform impedance through the adapter, avoid unnecessary branches, and use the manufacturer recommended QFN land pattern and exposed-pad connection for reliable operation.
Được đề xuất
USB Test and Measurement Fixture
Test fixtures frequently include long cable tails, adapters, relay contacts, and probe structures that increase USB High-Speed channel loss. The TUSB212RWBT can compensate for intersymbol interference in such a channel while remaining transparent to Low-Speed and Full-Speed operation. Pin-strap control is useful for a repeatable laboratory configuration, while I2C control permits automated characterization of AC boost and DC boost values. Validate the fixture with the intended cables and accessories and record eye width, jitter, and compliance results for every supported configuration.
Được đề xuất
Industrial USB Gateway
Industrial gateways often connect external sensors and service equipment through USB ports with cable runs longer than typical internal board channels. The TUSB212RWBT can be placed close to the impaired interface to apply selectable High-Speed compensation, while its host/device-agnostic design supports both sides of a USB connection. Configure the boost through pins for a fixed gateway design or use I2C for controlled adaptation. Confirm electromagnetic behavior, ground continuity, and USB compliance in the finished enclosure because external cable and chassis transitions can materially change the channel response.
Được đề xuất
USB Host Expansion Card
A host expansion card can suffer from loss accumulated across a mainboard connector, internal cable, and external peripheral lead. The TUSB212RWBT can correct the resulting USB 2.0 High-Speed intersymbol interference without changing the host protocol or requiring a separate path for lower speeds. Its compact 12-X2QFN package supports placement near the expansion connector, and its configurable AC and DC boost allows channel-specific tuning. Use the 5-meter pre-channel or 2-meter post-channel guidance as a boundary, then verify eye diagrams and mask compliance with the actual interconnect.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TUSB212RWBT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TUSB212RWBR |
|---|---|---|
| Package | 12-X2QFN | 12-X2QFN |
| Brand | Texas Instruments | Texas Instruments |
| Product Type | USB 2.0 high-speed signal conditioner | USB 2.0 high-speed signal conditioner |
| USB Compatibility | USB 2.0, OTG 2.0, and BC 1.2 | USB 2.0, OTG 2.0, and BC 1.2 |
| Supported Signaling | Low-Speed, Full-Speed, and High-Speed | Low-Speed, Full-Speed, and High-Speed |
| Configuration Method | Pin strap or I2C | Pin strap or I2C |
| AC Boost | Four selectable settings | Four selectable settings |
| DC Boost | Programmable | Programmable |
| Maximum Pre-Channel Length | 5 m | 5 m |
| Maximum Post-Channel Length | 2 m | 2 m |
| Package Dimensions | 1.6 mm x 1.6 mm | 1.6 mm x 1.6 mm |
Bảo phân biệt quan trọng
- Combines AC boost, DC boost, and selectable gain in one USB conditioner (vsTUSB212RWBR)
- Preserves Low-Speed and Full-Speed behavior while correcting High-Speed loss (vsTUSB212RWBR)
- Supports both fixed and firmware-managed compensation control (vsTUSB212RWBR)
Ghi chú thiết kế
Place the TUSB212RWBT near the boundary where the USB channel begins losing usable High-Speed margin. Keep the D1 and D2 traces matched, preserve the intended differential impedance, and avoid stubs or test pads that create reflections. Follow the Texas Instruments recommended 12-X2QFN land pattern and exposed-pad connection. Validate the final assembly with eye diagrams because connector launches, via structures, and cable transitions can dominate the conditioner’s own contribution.
Tune AC boost and DC boost from measured channel response rather than selecting the strongest available setting. Begin with eye width, jitter, and USB mask results at the intended worst-case cable and load, then evaluate the four selectable AC boost settings comparatively. Excessive equalization can increase jitter or create unintended waveform distortion. A repeatable bench procedure helps prevent the compensated channel from appearing acceptable only at room temperature with one test setup.
Use the supply and decoupling recommendations in the Texas Instruments TUSB212 datasheet when assigning the power pins and ground connections. Keep input and output bypass paths short, provide the required exposed-pad connection, and maintain a low-impedance ground reference. Since detailed supply-voltage and current limits are not established for the exact variant here, verify them in the manufacturer documentation before fixing the power architecture.
Do not treat the 5-meter pre-channel and 2-meter post-channel figures as guaranteed compliance in every implementation. The usable distance depends on the complete signal path, including connectors, cables, PCB transitions, loads, and the selected boost mode. Also verify whether the channel is upstream or downstream of the conditioner, because the applicable boundary differs. Document the worst-case configuration and retest it after cable, firmware, or board changes.
Thông tin tuân thủ
The exact TUSB212RWBT listing identifies the device as RoHS compliant and active. No exact-variant qualification or material-compliance statement establishes REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.