AD526JNZ - Software PGA, 1-16x Gain | Analog Devices
MPN: AD526JNZ ✓ 啟用中AD526JNZ 概覽
A software programmable gain amplifier, or SPGA, is an amplifier whose gain can be selected through digital control signals. It sits between the instrumentation-amplifier and operational-amplifier categories, allowing a system to attenuate or amplify a small analog input without changing external resistors. The AD526JNZ supports automatic range control, signal conditioning, measurement systems, and instrumentation where several input levels must share one analog processing chain.
The AD526JNZ provides five binary gain selections covering a 1-to-16 multiplication range. Gain is stored in latches, so the selected setting can remain stable while the analog signal is processed. Its monolithic implementation combines the amplifier and precision resistor network on one IC, while TTL-compatible gain-code inputs simplify interfacing with digital control logic. The 4 MHz bandwidth supports signal paths that require useful bandwidth beyond low-frequency precision measurements.
Internally, the AD526 uses a drift-trimmed BiFET amplifier with low input bias current, a laser-trimmed resistor network for gain accuracy, and JFET analog switches to select the active resistance. These elements implement the five gain modes without requiring external matched resistors or discrete switch networks. Because the gain code is latched, the control inputs do not need to remain actively driven after a valid code is stored.
Typical uses include programmable sensor-frontend scaling, laboratory measurement equipment, automatic-range data acquisition, industrial process monitoring, and communications equipment that accepts signals over a wide dynamic range. Placing the AD526JNZ ahead of an ADC can reduce the likelihood that a large input saturates the converter while preserving resolution for smaller signals.
The principal design consideration is digital-control timing. Firmware must set the latched gain code before the analog signal is sampled, and the circuit should avoid changing gain while a conversion is in progress. Power-supply decoupling, grounding, and signal-routing practices also remain important because the AD526JNZ is designed as a sensitive analog block within an otherwise digital system.
This page combines the AD526JNZ product identity, programmable-gain architecture, verified ordering information, replacement considerations, application guidance, and engineering design notes. It is intended to help engineers evaluate signal-conditioning requirements before integrating the amplifier into a PCB.
直接替換替代品,適用於 AD526JNZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: AD526JNZ (相同外形與佔位) — 差異在於 Package, Product Type.
AD526JNZ 最大額定值與電氣特性
| Product Type | Single-ended monolithic software programmable gain amplifier |
| Number of Circuits | 1 circuit |
| Selectable Gain | 1, 2, 4, 8, and 16 |
| Maximum Gain | 16x |
| Minimum Gain | 1x |
| Bandwidth | 4 MHz |
| Input Type | Single-ended |
| Amplifier Technology | BiFET |
| Resistor Network | Laser-trimmed |
| Switch Technology | JFET analog switches |
| Control Interface | TTL-compatible latched inputs |
| External Components Required | 0 components |
| 封裝 | 16-pin PDIP |
| Package Pitch | 7.62 mm |
| 安裝方式 | Through-hole |
AD526JNZ 7.62 mm 腳位配置指南
AD526JNZ(7.62 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD526JNZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD526JNZ 適用於 6 應用s: Programmable ADC Front End, Automatic-Range Sensor Conditioning, Industrial Process Measurement, Laboratory Instrumentation, Communications Signal Conditioning, Automatic Test and Measurement.
Programmable ADC Front End
The AD526JNZ fits an ADC input stage that must accommodate widely varying signal levels without changing external resistors. Its five selectable gains of 1x, 2x, 4x, 8x, and 16x let firmware attenuate a large input or amplify a smaller one before conversion. The 4 MHz bandwidth provides useful signal throughput, while the latched gain inputs simplify control from a microcontroller or FPGA. The design should set the gain code before each conversion and allow adequate settling time. Because the device is a single-ended amplifier, the source and ADC reference arrangement must provide a suitable common-mode range.
Automatic-Range Sensor Conditioning
The AD526JNZ is well suited to sensor interfaces in which the measured quantity can move across several orders of magnitude. A controller can select gains from 1x through 16x to keep the conditioned signal within a narrow ADC range, improving utilization of the converter rather than allowing one high-level input to determine the gain for every measurement. The integrated laser-trimmed resistor network and JFET switches provide a compact gain stage without external matched networks. Firmware should avoid gain changes during acquisition and should evaluate offset, settling, and noise performance for the particular sensor bandwidth.
Industrial Process Measurement
The AD526JNZ can serve as the programmable analog scaling stage in industrial process-monitoring equipment that accepts pressure, temperature, or current-derived signals. Digital gain selection makes it practical to establish different ranges for different transducers while retaining one analog signal path. The monolithic integration of the BiFET amplifier, trimmed resistor network, JFET switches, and latched controls reduces board area compared with a discrete implementation. Protective filtering should be placed ahead of the amplifier when sensors connect to long cables, and the grounding strategy must prevent switching or digital-control currents from entering the measurement reference.
Laboratory Instrumentation
The AD526JNZ is appropriate for laboratory instruments that need operator-selectable or software-controlled measurement ranges. Its 1x-to-16x gain range provides enough scaling flexibility for many low- and medium-frequency analog inputs, and the 4 MHz listed bandwidth handles signals beyond the slow range of a precision-only amplifier. The latched TTL-compatible controls allow the instrument controller to select a range and retain it during acquisition. For sensitive instrumentation, evaluate input bias current, offset voltage, noise, and gain error against the source impedance, then use clean grounding and short analog traces to preserve measurement integrity.
Communications Signal Conditioning
The AD526JNZ can provide programmable scaling ahead of a communications receiver when signal amplitude varies between operating states or channel conditions. Gain settings from 1x to 16x allow the receiver to preserve usable signal level without relying on a fixed attenuator network, while the 4 MHz bandwidth supports many baseband and control-signal paths. Latched gain control reduces repeated switching-command overhead. The amplifier remains a single-ended implementation, so system designers should account for single-ended signal sources, reference grounding, input bandwidth, and the maximum signal level accepted by the following stage when selecting a gain code.
Automatic Test and Measurement
The AD526JNZ is useful in automated test equipment that applies several gain scales to an input or DUT response. A test controller can select 1x, 2x, 4x, 8x, or 16x to normalize the signal before an ADC or measurement engine evaluates it. This can simplify fixture calibration and reduce the need for multiple interchangeable attenuator boards. For high-speed production testing, establish a deterministic sequence that latches gain before each sample, includes settling delay, and prevents acquisition interruption. Verify input and output clipping limits as well as the amplifier's thermal and supply conditions.
工程參考資料,適用於 AD526JNZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD526JN |
|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP |
| Brand | Analog Devices | Analog Devices |
| Product Type | Software programmable gain amplifier | Software programmable gain amplifier |
| Selectable Gain | 1x, 2x, 4x, 8x, and 16x | 1x, 2x, 4x, 8x, and 16x |
| Bandwidth | 4 MHz | 4 MHz |
| Input Configuration | Single-ended | Single-ended |
| Control Interface | TTL-compatible latched inputs | TTL-compatible latched inputs |
| External Gain Components | 0 components | 0 components |
| Lead Pitch | 7.62 mm | 7.62 mm |
主要差異化特點
- Five programmable gains integrated into one monolithic amplifier (對比AD526JN)
- Digital gain selection with retained settings (對比AD526JN)
- Complete integrated signal-gain function (對比AD526JN)
設計說明
Latch the gain code before starting each ADC conversion and do not change it while the converter is sampling. The AD526JNZ stores its gain setting, but the analog path still requires normal settling after a gain transition. Define a deterministic control sequence, include the required acquisition delay, and verify settling at the highest operating frequency and signal amplitude used by the design.
Place the amplifier and its bypass capacitors near the associated power and signal pins, and keep the analog input path short and away from digital switching nodes. Route the latched gain-control traces away from sensitive input and output tracks. For a through-hole 16-pin PDIP design, preserve a quiet analog ground reference and avoid sharing high-current return paths with the amplifier's measurement signal.
The AD526JNZ is a single-ended amplifier, so source impedance, input offset, gain accuracy, and output loading can affect the usable signal range. Check the source impedance against the BiFET input characteristics, confirm that the selected gain does not overdrive the next stage, and include the 4 MHz bandwidth when designing filters or cable compensation. Simulate the complete signal chain rather than relying only on nominal gain values.
Use the manufacturer's recommended bypass-capacitor arrangement and maintain a stable low-noise supply at the amplifier pins. Keep supply-loop current out of the analog input reference and avoid long shared return paths between the AD526JNZ and sensitive sensors. Confirm the exact supply-voltage limits and power-consumption values from the AD526 datasheet before finalizing the rail and thermal design.
合規資訊
The indexed AD526JNZ records do not state a specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration.