AD7472YRU - 12-Bit 1.5 MSPS ADC | Analog Devices
MPN: AD7472YRU ✓ 啟用中AD7472YRU 概覽
An ADC is a data-acquisition IC that converts an analog voltage into a digital code. The AD7472 belongs to the parallel-output SAR ADC family, combining a 12-bit resolution, 1.5 MSPS sampling capability, and low 4 mW power operation in a single package. The AD7470 is the related 10-bit member of the family, while AD7472 provides the higher resolution needed when the input-to-output quantization step must be smaller.
Key characteristics include 12-bit resolution, 1.5 MSPS maximum throughput, a 2.7 V to 5.25 V analog supply range, and a low-noise internal reference. The parallel interface presents the conversion result across dedicated digital output pins, allowing direct connection to a microcontroller, FPGA, DSP, or logic device without requiring a serial data link.
The successive-approximation architecture performs one conversion through a sequence of internal comparator decisions. Its throughput is suitable for industrial process monitoring, sensor acquisition, portable measurement equipment, and embedded control loops. Because the interface is parallel, the host processor must be able to accept and latch 12 bits of conversion data within the available acquisition interval.
A typical implementation places the AD7472 close to the analog input source and routes its digital outputs to a logic device. Short analog traces reduce pickup of noise and switching artifacts, while a solid ground plane and careful separation of analog and digital return currents help preserve conversion accuracy. The manufacturer datasheet should be consulted for the complete pin-description table, recommended input and reference circuits, and acquisition timing diagrams.
The AD7472YRU is suited to designers who require a parallel-output SAR converter with a compact 24-pin TSSOP footprint. AD7472ARU and AD7472BRU provide related temperature-grade choices, while the AD7470 members trade resolution for higher throughput. This page also organizes pricing evidence, replacement guidance, comparison parameters, and practical design notes for faster component selection.
直接替換替代品,適用於 AD7472YRU — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: AD7472YRU (相同外形與佔位) — 差異在於 Package, Input Type, Number of Channels, Resolution, Architecture.
AD7472ARUZ-REEL
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →AD7472BRU-REEL
✅ 直接替換聯絡詢價
查看資料表 →AD7470ARU
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD7470BRU
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD7472YRU 最大額定值與電氣特性
| ADC Type | Successive-approximation ADC |
| 解析度 | 12 bit |
| Number of Channels | 1 channel |
| Input Type | Single-ended analog input |
| 取樣率 | 1.5 MSPS |
| Supply Voltage Range | 2.7 V to 5.25 V |
| Power Consumption | 4 mW |
| Output Interface | Parallel |
| 封裝 | 24-pin TSSOP |
| Package Type | TSSOP-24 |
| 安裝類型 | Surface Mount |
| Reference | Internal low-noise reference |
AD7472YRU tssop-24 腳位配置指南
AD7472YRU(tssop-24 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD7472YRU.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD7472YRU 適用於 6 應用s: Industrial Sensor Acquisition, Precision Data-Acquisition Systems, Embedded Control and Monitoring, Portable Measurement Instruments, Audio and Vibration Monitoring, FPGA-Based Signal Processing.
Industrial Sensor Acquisition
The AD7472YRU is suitable for acquiring conditioned pressure, temperature, or position signals in industrial measurement systems. Its 12-bit resolution provides a finer digital representation than the 10-bit AD7470 family, while the 1.5 MSPS rate supports moderately fast process-control updates. Place the converter near the sensor interface to keep the analog input trace short, then latch the parallel outputs in an FPGA or microcontroller. The single 2.7 V to 5.25 V supply range supports both 3.3 V and 5 V designs, reducing the number of rails required around the acquisition chain.
推薦
Precision Data-Acquisition Systems
The 12-bit resolution and 1.5 MSPS throughput of the AD7472YRU fit compact precision DAQ modules that digitize several slow or medium-speed analog channels through multiplexing. Its parallel output allows the host processor to capture each code with a straightforward digital interface, avoiding the serial overhead of a serial-output converter. The 24-pin TSSOP package also supports dense board layouts, although a dedicated ground plane and short analog routing remain important for preserving measurement quality.
推薦
Embedded Control and Monitoring
The AD7472YRU can serve as the analog front end of an embedded controller that monitors a condition, pressure, or analog process variable and updates a control loop. Its 1.5 MSPS maximum rate is sufficient for many feedback and monitoring tasks, while 12-bit quantization gives the controller more useful information about small input changes. Connect its parallel outputs to the host MCU or DSP and use the acquisition timing from the manufacturer datasheet to establish the conversion and data-latch interval.
推薦
Portable Measurement Instruments
The low 4 mW power operation and 2.7 V to 5.25 V supply range of the AD7472YRU suit battery-powered handheld measurement equipment. A 3.3 V implementation can reduce both supply complexity and converter power demand compared with a higher-voltage analog rail, while the parallel outputs can be handled by a low-power embedded controller. Low power does not remove the need for careful reference grounding and analog layout, so the input network and bypass components should remain close to the device.
推薦
Audio and Vibration Monitoring
The AD7472YRU can be used for low-frequency vibration, acoustic, or waveform monitoring where the 12-bit resolution improves visibility of small signal changes and the 1.5 MSPS rate captures the required bandwidth. Place the converter at the output of a low-noise amplifier and anti-alias filter, and route the parallel output to an FPGA timing engine. The application must account for the 10-bit AD7470's higher 1.75 MSPS rate when sampling requirements prioritize maximum speed over output resolution.
推薦
FPGA-Based Signal Processing
The parallel data bus of the AD7472YRU maps naturally onto an FPGA acquisition pipeline, allowing the conversion code to be captured, filtered, or integrated without a serial interface. The 12-bit output and 1.5 MSPS throughput support continuous moderate-rate sampling, while the 24-pin TSSOP package allows placement near the analog front end. Designers should time the latch event from the acquisition sequence in the manufacturer datasheet and keep digital output routing away from the sensitive analog input and reference paths.
推薦
推薦產品摘要
工程參考資料,適用於 AD7472YRU — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD7472ARU | AD7472BRU | AD7470ARU | AD7470BRU |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | TSSOP-24 | TSSOP-24 | TSSOP-24 | TSSOP-24 | TSSOP-24 |
| Resolution | 12 bit | 12 bit | 12 bit | 10 bit | 10 bit |
| Sampling Rate | 1.5 MSPS | 1.5 MSPS | 1.5 MSPS | 1.75 MSPS | 1.75 MSPS |
| Supply Voltage Range | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V |
| ADC Architecture | Successive approximation | Successive approximation | Successive approximation | Successive approximation | Successive approximation |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Output Interface | Parallel | Parallel | Parallel | Parallel | Parallel |
| Temperature Grade | Y suffix ordering grade | A suffix ordering grade | B suffix ordering grade | A suffix ordering grade | B suffix ordering grade |
主要差異化特點
- Higher conversion resolution within the same family (對比AD7470ARU)
- Same-footprint temperature-grade flexibility (對比AD7472BRU)
- Resolution prioritized over maximum throughput (對比AD7470BRU)
設計說明
Route the analog input directly from the sensing or conditioning circuit to the AD7472YRU input pin, and keep the digital output traces away from that path. A continuous ground plane under the analog section helps establish a low-impedance return. Place supply-bypass and reference components close to their associated pins, following the layout and component values shown in the Analog Devices data sheet.
Capture each conversion using the conversion-complete timing and acquisition interval defined in the manufacturer data sheet. Because the AD7472YRU uses a parallel interface, the receiving FPGA or MCU must meet the setup and hold requirements at the indicated sampling edge. Avoid deriving an equivalent timing sequence solely from the 1.5 MSPS headline rate.
Do not treat an AD7470 device as an exact AD7472YRU replacement. The AD7470 family operates at up to 1.75 MSPS but provides only 10-bit resolution, whereas the AD7472 provides 12 bits at up to 1.5 MSPS. A substitution may also require firmware rescaling and verification of the full-scale code range before it is approved for production.
Design the analog and digital supplies around the 2.7 V to 5.25 V operating range. Bypass each supply connection at the device with the capacitance and placement recommended in the manufacturer data sheet, and keep switching-regulator loops and their high-current paths away from the analog input and reference network.
合規資訊
The available product information identifies the AD7472 family as a low-power ADC but does not provide explicit RoHS, REACH, halogen-free, or conflict-minerals declarations. AEC-Q100 status is marked not applicable because the part is not identified as an automotive-qualified device.