EFM32TG222F32-D-QFP48 - 32MHz Cortex-M3 MCU | Silicon Labs
MPN: EFM32TG222F32-D-QFP48 ✓ 啟用中EFM32TG222F32-D-QFP48 概覽
A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The EFM32TG222 belongs to the Tiny Gecko family within the EFM32 product portfolio. Its combination of 32 MHz processing performance, 4 kB SRAM, and extensive configurable peripherals makes it suitable for applications that need responsive control, efficient serial communication, and compact implementation in a 7 mm × 7 mm surface-mount package.
Key features include 32 kB Flash, 4 kB RAM, 37 digital I/O pins, two 16-bit timers, AES hardware, and three operational amplifiers. The supply-voltage range of 1.98 V to 3.8 V supports common low-voltage system rails. Fast wake-up and energy-saving modes are important for devices that spend substantial time asleep and need short active intervals for sensor acquisition, control updates, or communications.
The ARM Cortex-M3 architecture provides a 32-bit processing environment while retaining a straightforward embedded instruction set. Two 16-bit timers support periodic timing, pulse measurement, and motor or general-purpose control tasks. Configurable I/O allows pins to be assigned according to board-level routing, while the operational amplifiers can reduce external analog component count in suitable low-level signal-conditioning designs.
Typical uses include industrial sensor nodes, compact energy meters, building controls, portable accessories, battery-powered instrumentation, and connected IoT equipment. In these systems, the microcontroller can acquire sensor data, execute control logic, drive indicators, and communicate through configured serial peripherals. Its 48-pin TQFP footprint also provides more I/O than smaller QFN packages commonly used for cost-constrained designs.
Designers should preserve the manufacturer-recommended decoupling and programming interfaces, and they should review the complete pin-description table before assigning signals. The exposed 1.98 V to 3.8 V operating range requires compatible power regulation, while careful clock and sleep-mode planning is essential for achieving low average energy consumption in battery-operated products.
直接替換替代品,適用於 EFM32TG222F32-D-QFP48 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: EFM32TG222F32-D-QFP48 (相同外形與佔位) — 差異在於 Flash Memory, Package, Product Type, Series, Architecture.
EFM32TG222F32-QFP48
✅ 直接替換聯絡詢價
查看資料表 →EFM32ZG222F32-QFP48
✅ 直接替換聯絡詢價
查看資料表 →EFM32HG222F32G-A-QFP48
✅ 直接替換📋 參考替代品(不在目錄中)
EFM32HG321F32G-A-QFP48R
✅ 直接替換📋 參考替代品(不在目錄中)
EFM32TG822F8-QFP48
✅ 直接替換聯絡詢價
查看資料表 →EFM32TG222F32-D-QFP48 最大額定值與電氣特性
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Series | EFM32 Tiny Gecko |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 32 kB |
| RAM | 4 kB |
| Digital I/O Pins | 37 pins |
| Timers | 2 × 16-bit timers |
| 工作電源電壓 | 1.98 V to 3.8 V |
| CPU Architecture | ARM Cortex-M3, 32-bit RISC |
| Security Feature | AES hardware |
| Operational Amplifiers | 3 integrated operational amplifiers |
| 封裝 | 48-pin TQFP, 7 mm × 7 mm |
| 安裝類型 | Surface mount |
| Program Memory Type | Flash |
| Low-Power Features | Energy-saving modes and fast wake-up |
EFM32TG222F32-D-QFP48 48-pin tqfp, 7 mm × 7 mm 腳位配置指南
EFM32TG222F32-D-QFP48(48-pin tqfp, 7 mm × 7 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: EFM32TG222F32-D-QFP48.
請參閱 資料表 以查看完整腳位配置。
典型應用
EFM32TG222F32-D-QFP48 適用於 6 應用s: Battery-Powered Sensor Nodes, Industrial Condition Monitoring, Smart Energy Metering, Building Control Equipment, Portable Medical Accessories, Connected IoT Gateways.
Battery-Powered Sensor Nodes
The EFM32TG222F32-D-QFP48 fits compact sensor nodes that periodically wake, acquire measurements, evaluate control logic, and return to sleep. Its energy-saving modes and fast wake-up behavior reduce the inactive interval between events, while the 32 MHz Cortex-M3 core allows control work to be completed without raising the clock continuously. The 32 kB Flash accommodates firmware and fixed data, and 4 kB RAM supports transient sensor processing, although designs requiring large sample buffers should account for the 4 kB limit. The 1.98 V to 3.8 V supply range also supports low-voltage battery-derived rails when the regulator and cell chemistry are selected appropriately.
推薦
Industrial Condition Monitoring
The EFM32TG222F32-D-QFP48 can serve as the control and communications MCU in industrial condition-monitoring equipment that measures vibration, temperature, current, or equipment state. Two 16-bit timers provide timing resources for periodic sampling and event detection, while 37 digital I/O pins leave substantial control and interface capacity. Its 32 MHz processing rate supports responsive signal evaluation, and the 48-pin TQFP package offers ample routing space for debug, communications, and discrete I/O. The 1.98 V to 3.8 V operating range permits integration with industrial low-voltage rails, provided the system protects the device from transients outside the specified limits.
推薦
Smart Energy Metering
The EFM32TG222F32-D-QFP48 is appropriate for compact energy-metering controllers that must combine periodic measurement, local calculations, status indication, and communications. Its 32 kB Flash provides space for metering firmware, 4 kB RAM supports working state, and the 37 I/O pins can be assigned to sensor inputs, display control, communications, and configuration controls. AES hardware can assist with secure data handling when the complete firmware architecture defines appropriate keys and protocols. Because the RAM is limited to 4 kB, designs should stream or aggregate samples carefully rather than retain long uncompressed histories.
推薦
Building Control Equipment
The EFM32TG222F32-D-QFP48 fits building-control modules that coordinate digital inputs, outputs, and low-speed communications while managing energy use. Its energy-saving modes support systems that remain connected to building power but avoid continuous high-rate processing, and fast wake-up behavior improves response after a scheduled or event-driven wake. The 48-pin TQFP package provides more I/O than compact QFN devices, which is useful for multiple relay-control inputs, status LEDs, bus connections, and service interfaces. The three integrated operational amplifiers may simplify suitable low-level sensing stages, although external buffering or protection should be added where signal amplitude or noise conditions require it.
推薦
Portable Medical Accessories
The EFM32TG222F32-D-QFP48 can be used in low-power portable medical accessories that perform local control, user-interface management, and limited data processing. Its low-power architecture is valuable in battery-powered products, while 37 digital I/O pins provide flexibility for buttons, indicators, sensors, and external interface control. The integrated three operational amplifiers can support suitable low-level analog stages without requiring a separate amplifier in every design. Medical applications still require application-specific review of electrical safety, isolation, accuracy, firmware validation, and regulatory obligations; the MCU specification alone does not establish medical certification or compliance.
推薦
Connected IoT Gateways
The EFM32TG222F32-D-QFP48 is suitable for compact IoT edge nodes that aggregate local sensor information and manage power-efficient communications. The 32 MHz Cortex-M3 core handles protocol tasks and application logic, while 32 kB Flash and 4 kB RAM support embedded firmware that does not require a large operating system. Its 37 digital I/O pins allow connection of sensors, indicators, and status inputs around a network interface. The low-power modes and fast wake-up behavior help support duty-cycled operation, but protocol buffering must be sized around the 4 kB RAM limit. An Ethernet companion can provide connectivity where the gateway architecture requires it.
推薦
推薦產品摘要
工程參考資料,適用於 EFM32TG222F32-D-QFP48 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | EFM32TG222F32-QFP48 | EFM32ZG222F32-QFP48 | EFM32HG222F32G-A-QFP48 | EFM32HG321F32G-A-QFP48R | EFM32TG822F8-QFP48 |
|---|---|---|---|---|---|---|
| Package | 48-pin TQFP (7 mm × 7 mm) | 48-pin TQFP (7 mm × 7 mm) | 48-pin TQFP (7 mm × 7 mm) | 48-pin TQFP (7 mm × 7 mm) | 48-pin TQFP (7 mm × 7 mm) | 48-pin TQFP (7 mm × 7 mm) |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Flash Memory | 32 kB | 32 kB | 32 kB | 32 kB | 32 kB | 8 kB |
主要差異化特點
- Higher maximum clock speed than the Zero Gecko alternative (對比EFM32ZG222F32-QFP48)
- Four times the Flash capacity of the reduced-memory Tiny Gecko option (對比EFM32TG822F8-QFP48)
- AES hardware and three integrated operational amplifiers in one MCU (對比EFM32HG222F32G-A-QFP48)
- Closeest same-core, same-memory, same-package alternative (對比EFM32TG222F32-QFP48)
設計說明
Design the supply for the specified 1.98 V to 3.8 V operating range, including startup and transient margins. Place the manufacturer's recommended decoupling capacitors close to the supply and ground pins, and keep high-current return paths away from sensitive analog inputs. The integrated operational amplifiers can reduce external analog component count, but their supply, common-mode range, output swing, and stability requirements must be checked before using them in a signal path.
Use the complete 48-pin pin-description table when assigning signals because multiplexed functions and alternate debug interfaces can restrict otherwise available I/O. Route sensitive analog inputs away from switching nodes and digital clock traces, provide a quiet ground reference for analog circuitry, and follow the manufacturer's recommended footprint dimensions. Check programming and debug access before finalizing the PCB so connector placement does not interfere with the MCU or surrounding components.
Estimated average-current calculation: use Iavg = Iactive × tactive + Isleep × tsleep over one complete operating cycle, then multiply by the supply voltage to estimate energy per cycle. For example, with 3.3 V, 10 mA active for 20 ms, and 5 µA sleep for 980 ms, the calculated average current is approximately 0.205 mA. Actual duty-cycle values must come from the deployed firmware and peripheral measurements.
Do not treat a same-package candidate as a guaranteed functional replacement. The EFM32ZG222F32-QFP48 changes the core and maximum clock speed, the HG candidates belong to different peripheral families, and the EFM32TG822F8-QFP48 has only 8 kB Flash. Review peripheral availability, interrupt behavior, startup files, firmware dependencies, and qualification before approving a substitution.
合規資訊
The manufacturer documentation should be used to confirm environmental, material, and automotive qualification requirements for the exact ordering code.