PIC16F871-E/P - 8-bit MCU, 3.5KB Flash, 20MHz, 40-Pin PDIP | Microchip
MPN： PIC16F871-E/P ✓ 啟用中PIC16F871-E/P 概覽
What is a PIC16 microcontroller? The PIC16 family is a line of 8-bit Harvard-architecture microcontrollers from Microchip Technology that sits within the broader taxonomy of microcontroller -> embedded processor -> semiconductor. PIC16 devices use a reduced instruction set (RISC) with typically 35 single-word instructions, are Flash-based for in-field reprogrammability, and are widely used in cost-sensitive embedded designs ranging from appliance controls to industrial sensors. The PIC16F871 specifically belongs to the "PIC16F87x" mid-range sub-family with enhanced peripherals such as 10-bit ADC and USART.
Key features include an integrated ICD (In-Circuit Debugger) interface, self-programming capability, eight channels of 10-bit Analog-to-Digital conversion, two additional 8-bit timers, a 16-bit timer with capture/compare/PWM, and a Universal Asynchronous Receiver Transmitter (USART) for serial communications. The part is fully static, supports nanoWatt power management for low-power sleep modes, and exposes 33 digital I/O lines across two ports (PORTA, PORTB, PORTC, PORTD, PORTE).
Architecturally the PIC16F871 uses a Harvard memory layout with separate program and data buses, allowing simultaneous instruction fetch and operand access. Its 14-bit wide instruction word yields high code density, and the in-circuit serial programming (ICSP) interface plus ICD permit real-time debug without removing the device from the board - a feature uncommon in this price tier.
Typical applications include industrial control panels, motor drive interface logic, HVAC thermostats, appliance controllers, instrumentation front-ends, and educational/learning kits where the PIC16F871's simple toolchain (MPLAB X IDE + XC8 compiler + PICkit programmer) keeps development costs low. Designers favor this MCU when they need ADC, PWM, and serial I/O in a single 40-pin footprint.
When designing with the PIC16F871-E/P, place decoupling capacitors (100 nF ceramic plus 10 uF bulk) within 5 mm of the VDD pins, use a 4.7 kΩ pull-up on MCLR if not driven by a debug tool, and observe the 4.0 V minimum VDD - operation below this rail causes EEPROM write failure and unreliable ADC readings.
This page synthesizes Microchip datasheet specifications, distributor pricing snapshots, and a focused set of drop-in PIC16F871 alternatives not always surfaced on DigiKey or Mouser product pages, helping engineers verify pin compatibility and parametric proximity before committing to a substitution.
直接替換替代品，適用於 PIC16F871-E/P — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： PIC16F871-E/P （相同外形與佔位） — 差異在於 Mounting Type, I/O Pins, In-Circuit Debug, Package, Self-Programming.
PIC16F870-E/P
✅ 直接替換📋 參考替代品（不在目錄中）
PIC16F872-E/P
✅ 直接替換📋 參考替代品（不在目錄中）
PIC16F871-E/L
✅ 直接替換聯絡詢價
查看資料表 →PIC16F871-I/P
✅ 直接替換聯絡詢價
查看資料表 →PIC16F873A-I/P
✅ 直接替換📋 參考替代品（不在目錄中）
PIC16F876A-I/P
✅ 直接替換📋 參考替代品（不在目錄中）
PIC16F871-E/P 最大額定值與電氣特性
| Core Processor | PIC |
| Core Size | 8-bit |
| Program Memory Type | Flash |
| Program Memory Size | 3.5 KB (3.5K x 14) |
| RAM Size | 192 bytes |
| EEPROM Size | 64 bytes |
| Maximum Clock Speed | 20 MHz |
| Instruction Cycle | 200 ns |
| Supply Voltage (VDD) | 4.0 V to 5.5 V |
| 工作溫度 | -40C to +125C |
| 封裝 / 外殼 | 40-DIP (0.600", 15.24 mm) |
| Number of I/O Pins | 33 |
| ADC | 8 channels x 10-bit |
| Timers | 2 x 8-bit + 1 x 16-bit (with capture/compare/PWM) |
| Communication Interfaces | USART |
| In-Circuit Debug | ICD |
| Self-Programming | Yes (Flash) |
| 安裝類型 | Through-Hole (PDIP) |
PIC16F871-E/P 腳位配置
| 腳位 1 | MCLR — Master Clear (reset) input, active low |
| 腳位 2 | RA0/AN0 — PORTA bit 0 / ADC channel 0 |
| 腳位 3 | RA1/AN1 — PORTA bit 1 / ADC channel 1 |
| 腳位 4 | RA2/AN2 — PORTA bit 2 / ADC channel 2 |
| 腳位 5 | RA3/AN3/VREF+ — PORTA bit 3 / ADC channel 3 / ADC positive reference |
| 腳位 6 | RA4/AN4 — PORTA bit 4 / ADC channel 4 |
| 腳位 7 | RA5/AN5/SS — PORTA bit 5 / ADC channel 5 / SPI slave select |
| 腳位 8 | RE0/RD/AN5 — PORTE bit 0 / parallel-port read / ADC channel 5 alt |
| 腳位 9 | RE1/WR/AN6 — PORTE bit 1 / parallel-port write / ADC channel 6 |
| 腳位 10 | RE2/CS/AN7 — PORTE bit 2 / parallel-port chip select / ADC channel 7 |
| 腳位 11 | VDD — Positive supply (4.0 V to 5.5 V) |
| 腳位 12 | VSS — Ground reference |
| 腳位 13 | OSC1/CLKI — Oscillator crystal input / external clock input |
| 腳位 14 | OSC2/CLKO — Oscillator crystal output / clock output |
| 腳位 15 | RC0/T1OSO — PORTC bit 0 / Timer1 oscillator output |
| 腳位 16 | RC1/T1OSI — PORTC bit 1 / Timer1 oscillator input |
| 腳位 17 | RC2/CCP1 — PORTC bit 2 / Capture-Compare-PWM 1 |
| 腳位 18 | RC3 — PORTC bit 3 |
| 腳位 19 | RD0 — PORTD bit 0 |
| 腳位 20 | RD1 — PORTD bit 1 |
| 腳位 21 | RD2 — PORTD bit 2 |
| 腳位 22 | RD3 — PORTD bit 3 |
| 腳位 23 | RC4 — PORTC bit 4 |
| 腳位 24 | RC5 — PORTC bit 5 |
| 腳位 25 | RC6/TX/CK — PORTC bit 6 / USART TX / clock |
| 腳位 26 | RC7/RX/DT — PORTC bit 7 / USART RX / data |
| 腳位 27 | RD4 — PORTD bit 4 |
| 腳位 28 | RD5 — PORTD bit 5 |
| 腳位 29 | RD6 — PORTD bit 6 |
| 腳位 30 | RD7 — PORTD bit 7 |
| 腳位 31 | VSS — Ground reference |
| 腳位 32 | VDD — Positive supply (4.0 V to 5.5 V) |
| 腳位 33 | RB0/INT — PORTB bit 0 / external interrupt |
| 腳位 34 | RB1 — PORTB bit 1 |
| 腳位 35 | RB2 — PORTB bit 2 |
| 腳位 36 | RB3/PGM — PORTB bit 3 / low-voltage programming |
| 腳位 37 | RB4 — PORTB bit 4 |
| 腳位 38 | RB5 — PORTB bit 5 |
| 腳位 39 | RB6/PGC — PORTB bit 6 / ICSP clock |
| 腳位 40 | RB7/PGD — PORTB bit 7 / ICSP data |
典型應用
PIC16F871-E/P 適用於 6 應用s: Industrial Control Panels, Appliance Motor Controllers, HVAC Thermostat Interface, Instrumentation Front-Ends, Educational Microcontroller Kits, Sensor Hub / Data Logger.
Industrial Control Panels
The PIC16F871-E/P fits industrial control panels because its 8-channel 10-bit ADC can read multiple sensor inputs (temperature, pressure, current) while its USART drives a local HMI or Modbus link. The -40C to +125C extended temperature grade handles factory-floor thermal swings, and the 40-pin PDIP package is friendly to hand-soldered prototypes and field-repair workflows.
推薦
Appliance Motor Controllers
In appliance motor controllers the PIC16F871-E/P's 16-bit timer with capture/compare/PWM drives FET gate signals for brushed and small BLDC motors, while the ADC monitors back-EMF and current. The 5 V supply rail aligns with typical appliance power trees and the 200 ns instruction cycle is fast enough for commutation loops under 10 kHz.
推薦
HVAC Thermostat Interface
Thermostat designs benefit from the PIC16F871-E/P's 8-channel ADC reading thermistor or RTD sensors, USART driving a Wi-Fi/Ethernet co-processor, and PWM dimming a backlight or buzzer. nanoWatt sleep modes drop standby current for battery-backed thermostats and the 40-pin PDIP simplifies through-hole assembly for high-volume HVAC OEMs.
推薦
Instrumentation Front-Ends
Bench and field instruments use the PIC16F871-E/P to digitize analog front-end signals through its 10-bit ADC and forward calibration data over USART to a host PC. The ICD interface lets engineers step through acquisition code without removing the chip, and the extended temperature range keeps the part stable inside enclosure enclosures without active cooling.
推薦
Educational Microcontroller Kits
Universities and self-learners favor the PIC16F871-E/P because the 40-pin PDIP seats in any breadboard and pairs with low-cost PICkit programmers. MPLAB X IDE + XC8 compiler are free, the PIC16 instruction set has only 35 single-word opcodes, and the 8-channel ADC plus PWM give students enough peripherals for real lab projects without overwhelming beginners.
推薦
Sensor Hub / Data Logger
Low-cost data loggers route multiple analog channels into the PIC16F871-E/P's 10-bit ADC and store calibration plus timestamps in the 64-byte EEPROM. The USART streams captured data to a host, and self-programming enables firmware updates in the field without an external bootloader. The 40-pin PDIP makes it serviceable in remote installations.
推薦
推薦產品摘要
工程參考資料，適用於 PIC16F871-E/P — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | PIC16F870-E/P | PIC16F872-E/P | PIC16F871-E/L | PIC16F871-I/P | PIC16F873A-I/P |
|---|---|---|---|---|---|---|
| Package | 40-pin PDIP | 40-pin PDIP (same) | 40-pin PDIP (same) | 44-pin PLCC (adapter needed) | 40-pin PDIP (same) | 40-pin PDIP (same) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 3.5 KB | 2 KB | 4 KB | 3.5 KB | 3.5 KB | 7.2 KB |
| RAM | 192 bytes | 128 bytes | 192 bytes | 192 bytes | 192 bytes | 192 bytes |
| EEPROM | 64 bytes | 64 bytes | 64 bytes | 64 bytes | 64 bytes | 256 bytes |
| Max Clock Speed | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Operating Temperature | -40C to +125C (Extended) | -40C to +125C (Extended) | -40C to +125C (Extended) | -40C to +125C (Extended) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| ADC Channels | 8 x 10-bit | 8 x 10-bit | 8 x 10-bit | 8 x 10-bit | 8 x 10-bit | 5 x 10-bit |
| PWM Outputs | 1 (CCP1) | 1 (CCP1) | 1 (CCP1) | 1 (CCP1) | 1 (CCP1) | 2 (CCP1+CCP2) |
主要差異化特點
- Higher Flash density than PIC16F870 in identical 40-pin PDIP package (對比PIC16F870-E/P)
- More I/O and ADC channels than PIC16F873A's reduced-pin variants (對比PIC16F873A-I/P)
- Lower cost than PIC16F872 for cost-sensitive designs (對比PIC16F872-E/P)
- Extended -40C to +125C temperature grade vs industrial -40C to +85C (對比PIC16F871-I/P)
設計說明
Place a 100 nF ceramic decoupling capacitor within 5 mm of every VDD pin (pins 11 and 32) and a single 10 uF bulk tantalum or aluminum electrolytic on the supply rail. The PIC16F871-E/P switches internal digital blocks at up to 20 MHz; without local bypassing the VDD rail can sag 50-100 mV during ADC conversions, degrading 10-bit accuracy by 1-2 LSB.
MCLR must be pulled high through a 4.7 kΩ resistor for normal operation - leaving MCLR floating can cause intermittent resets or, when driving the ICSP debugger, prevent connection. When using ICD debugging, route the PGC (RB6) and PGD (RB7) lines away from high-current switching nodes; capacitive loading above 30 pF on these pins can break the ICSP clock.
Route the analog AVdd/AVss rails as a star from a single point at the regulator, and keep ADC traces (RA0-RA5, RE0-RE2) short and guarded by digital ground. For AREF use a 0.1 uF + 10 uF RC filter rather than driving AREF from a noisy source - the 10-bit ADC dynamic range depends on a clean reference.
Estimated: at 20 MHz, 5 V, and 100% CPU duty, ICC is approximately 15-20 mA, dissipating 75-100 mW in the PIC16F871-E/P. With theta_JA around 50 C/W for a 40-pin PDIP, the junction rise is only 4-5 C above ambient - well within the 125 C limit and rarely a concern at this clock/power profile.
合規資訊
RoHS and REACH compliance inferred from Microchip's standard product labeling for PIC16Fxxx PDIP parts; specific test certificates are available on Microchip's product page.
