AD977BRSZ - 16-Bit 100 kSPS SAR ADC | Analog Devices
料号: AD977BRSZ ✗ 停产AD977BRSZ 概述
An ADC converts an analog input voltage into a digital code for processing, storage, or transmission. The AD977 belongs to the successive-approximation ADC, or SAR ADC, category within the broader analog-to-digital converter and semiconductor hierarchy. SAR AD977-family devices compare the input against an internally generated DAC value during successive conversion cycles. Their serial interface reduces the number of external signal connections, while the internal reference simplifies analog front-end design and system calibration.
The AD977BRSZ combines 16-bit resolution with a 100 kSPS conversion rate. It operates from a single 5 V rail, with a stated supply range of 4.75 V to 5.25 V. Its power dissipation is listed at a maximum of 100 mW, and a power-down mode is available for reducing consumption when conversions are not required. The operating-temperature range extends from -40°C to +85°C, supporting industrial-temperature equipment when the complete system is designed for that environment.
Internally, the AD977 uses a switched-capacitor successive-approximation architecture. The manufacturer describes the family as factory calibrated to minimize all linearity errors, reducing the need for board-level offset, gain, and nonlinearity correction in many applications. The high-speed serial interface provides a compact connection to a controller or programmable logic device. Because the converter uses an internal 2.5 V reference, designers should budget for the resulting input range and avoid assuming that the full 5 V supply can be applied directly to the analog input.
Typical uses include industrial process monitoring, sensor signal acquisition, instrumentation, communications equipment, and embedded control systems where a 16-bit measurement interface is needed without a high-speed parallel bus. The 100 kSPS rate is appropriate for many slowly changing analog quantities, including temperature, pressure, position, and analog instrumentation signals. The part can also support repeated sampling when the application requires more frequent updates than a slow sensor naturally produces.
Layout should preserve a quiet analog return path and keep the serial clock and data traces away from sensitive input routing. Decoupling should be placed close to the supply pins, and unused inputs should be handled according to the manufacturer pin-description table. Designers should also check acquisition timing against the serial clock rate and digital control timing rather than assuming that the maximum sample rate is suitable for every signal or data-capture implementation.
This product page consolidates the manufacturer specifications, package information, sourcing context, and engineering guidance for the AD977BRSZ. It also identifies the closely related family members that can support replacement decisions while making clear that a physical footprint match alone does not guarantee identical conversion throughput.
直接替换替代料: AD977BRSZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: AD977BRSZ (相同外形与封装尺寸) ——差异在于 Package, Converter Type, Factory Calibration, Throughput Rate, Architecture.
AD977BRSZ 最大额定值与电气特性
| 分辨率 | 16 bit |
| Architecture | Successive approximation (SAR) |
| Input Type | Single input |
| Throughput Rate | 100 kSPS |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Internal Reference Voltage | 2.5 V |
| Data Interface | Serial, SPI |
| Power Dissipation | 100 mW maximum |
| Power-Down Mode | 50 W maximum input power |
| 工作温度 | -40°C to +85°C |
| 封装 | 28-pin SSOP, 5.30 mm width |
| Package Pitch | 0.65 mm |
| 安装类型 | Surface mount |
| Factory Calibration | Minimizes all linearity errors |
AD977BRSZ 0.65 mm 引脚配置指南
AD977BRSZ(0.65 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: AD977BRSZ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
AD977BRSZ 适用于 6 应用s: Industrial Sensor Signal Acquisition, Process Control Monitoring, Precision Test and Measurement, Communications and Data Acquisition, Position and Motor Feedback, Battery-Powered Embedded Measurement.
Industrial Sensor Signal Acquisition
The AD977BRSZ fits industrial sensor acquisition when the measured signal changes slowly enough for a 100 kSPS SAR conversion rate. Its 16-bit resolution provides 65,536 digital codes across the converter's specified analog-input range, while the single 4.75 V to 5.25 V supply simplifies power planning around 5 V instrumentation. A typical circuit buffers the sensor with an amplifier, applies suitable filtering, and presents the analog signal to the ADC input. The internal 2.5 V reference and factory calibration reduce calibration burden, although input-referred noise, settling time, and sensor drive impedance still determine overall measurement accuracy.
Process Control Monitoring
The AD977BRSZ can digitize slow process variables such as temperature, pressure, level, or valve position for a programmable controller. A 100 kSPS throughput rate gives the control loop many more samples than most thermal or mechanical process variables require, while the compact 28-pin SSOP preserves board area. The serial interface reduces trace count compared with a parallel ADC, but the controller must generate the required clock and correctly interpret conversion timing. Firmware should also reject samples acquired during settling or transient periods so the controller acts on stable measurements.
Precision Test and Measurement
The 16-bit AD977BRSZ is appropriate for instrumentation that converts a conditioned analog measurement into a digital value for display, logging, or calibration. Its 100 kSPS sampling rate is suitable for many laboratory and bench instruments that prioritize resolution and stable references over very high conversion speed. The internal 2.5 V reference and factory calibration support repeatable measurements, but instrument accuracy also depends on the input amplifier's offset, drift, noise, and settling behavior. Grounding and decoupling must be designed so the ADC reference and analog input remain insensitive to digital switching activity.
Communications and Data Acquisition
The AD977BRSZ can serve as the conversion element in compact communications or data-acquisition equipment that accepts a bounded analog input and uses a serial data link. The 28-pin SSOP package supports space-constrained board layouts, and the high-speed serial interface can coexist with digital control and communications circuitry on the same assembly. At 100 kSPS, the ADC can generate 100,000 samples each second before protocol overhead. The system clock must meet the serial-interface requirements, and sampled data should be framed unambiguously so that command latency, packet boundaries, and acquisition timing remain deterministic.
Position and Motor Feedback
The AD977BRSZ is suitable for digitizing position or potentiometer-based feedback signals where a 16-bit measurement interface is needed but high-bandwidth motor sampling is unnecessary. A buffered resistive divider or ratiometric sensor can feed the converter while the controller reads the result through the serial interface. The 100 kSPS rate supports frequent refresh in many feedback loops, but mechanical or electrical settling must be allowed before each conversion. Designers should also evaluate the sensor's noise and the ADC input network against the required angular or positional resolution rather than assuming that nominal bit depth alone defines usable accuracy.
Battery-Powered Embedded Measurement
The AD977BRSZ supports compact embedded measurement systems that require 16-bit readings from a single 5 V rail. Its low-power SAR architecture and listed 100 mW maximum dissipation make it suitable for instrumentation in which conversion energy and board area matter. The power-down mode can reduce consumption during inactive intervals, although actual system savings depend on how the converter is sequenced and how long it remains disabled. Designers should include a local 5 V source with adequate transient response, place bypass capacitance near the supply pins, and preserve a low-noise analog return path for best conversion repeatability.
工程参考数据: AD977BRSZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | AD977BRS | AD977BRZ |
|---|---|---|---|
| Package | 28-pin SSOP, 0.65 mm pitch | 28-pin SSOP | 28-pin SSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Resolution | 16 bit | 16 bit | 16 bit |
| Throughput Rate | 100 kSPS | 100 kSPS | 100 kSPS |
| Architecture | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) |
| Supply Voltage Range | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Internal Reference | 2.5 V | 2.5 V | 2.5 V |
| Data Interface | Serial, SPI | Serial, SPI | Serial, SPI |
| Power Dissipation | 100 mW maximum | 100 mW maximum | 100 mW maximum |
| Operating Temperature | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
关键差异点
- Matches the core AD977 family conversion specifications (对比 AD977BRS)
- Offers the same 100 kSPS performance class in a related ordering code (对比 AD977BRZ)
- Uses a compact 28-pin serial-interface package (对比 AD977BRS)
设计说明
Place the 5 V bypass capacitor close to the converter's supply and ground pins, and keep the return current out of the sensitive analog-input path. The converter operates over 4.75 V to 5.25 V, so the source should remain within this range under load and transient conditions. If the analog front end uses a regulated rail derived from a switching converter, allow additional filtering or an appropriately placed linear stage when converter ripple could affect the measurement.
Route the analog input directly from the sensing or conditioning circuit and keep the serial clock, data, and control traces away from the input node. Use a continuous ground plane and place input-side bypass or filtering components where they can isolate the source without creating long, high-impedance routes. Follow the manufacturer package drawing and pin-description table for the 28-pin SSOP orientation before defining the footprint and assembly land pattern.
Do not treat the 5 V supply as the converter's full-scale input range. The AD977 family includes an internal 2.5 V reference, so the analog input must be conditioned to remain within the ADC's specified input range. Also verify acquisition timing at 100 kSPS: the serial clock, conversion latency, data-valid interval, and controller response must satisfy the datasheet timing sequence before sampling is increased.
合规信息
The manufacturer product page does not provide explicit component-level RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements for this ordering code. AEC-Q100 is not applicable because this product is not an automotive-qualified ordering variant.