ADS7842E/1K - 12-Bit 4-Channel 200ksps ADC | Texas Instruments
料号: ADS7842E/1K ✓ 量产中ADS7842E/1K 概述
An ADC converts an analog input voltage into a digital value suitable for processing, measurement, logging, or control. The ADS7842 belongs to the SAR ADC family, where an internal capacitor-based DAC and successive comparison determine each conversion result. Within the electronics hierarchy, it is a data-converter IC and an ADC/DAC category component designed for precision analog-signal capture. Its four-input multiplexer supports multiple sensors or measurement nodes without requiring four separate converter packages.
Key features include 12-bit resolution, a maximum sampling rate of 200 ksample/s, ±1 LSB integral and differential nonlinearity, and 72 dB SINAD. The single-supply operating range of 2.7 V to 5 V supports both 3.3 V and 5 V systems. An adjustable reference from 100 mV to VCC changes the full-scale input range and corresponding LSB resolution from 24 µV to 1.22 mV. Low power dissipation of 2 mW helps reduce system energy consumption in portable and battery-operated instruments.
The device combines a four-channel analog multiplexer, sample-and-hold amplifier, 12-bit SAR core, control logic, and three-state parallel output drivers. Parallel data output permits direct connection to appropriately buffered microprocessor or data-bus circuitry. The three-state outputs can place the bus in a high-impedance state when the converter is not selected. At 200 ksample/s, the architecture provides sufficient throughput for moderate-rate instrumentation while retaining the simple control and conversion behavior associated with SAR ADCs.
Typical uses include portable data loggers, test and measurement equipment, industrial process monitoring, battery-powered instruments, and laboratory data-acquisition systems. It is particularly useful when several analog channels must be sampled with a compact parallel-interface converter. The 200 ksample/s rate supports rapidly changing sensor signals, while the 12-bit result provides 4096 digital codes across the selected reference range.
PCB design should provide a low-impedance reference network and short analog traces to minimize acquisition errors and coupling. Decoupling capacitors should be placed close to the supply and reference pins, and digital output routing should avoid crossing sensitive input paths. Because the converter uses an adjustable reference, resistor and capacitor tolerances directly influence LSB size and calibration accuracy.
This product page combines the manufacturer specifications with practical application guidance, package details, replacement considerations, interface constraints, and PCB design notes. These engineering details help designers determine whether the ADS7842E/1K’s 12-bit resolution, four-channel multiplexing, 200 ksample/s throughput, parallel bus, and 2.7 V to 5 V supply range fit a specific data-acquisition design.
直接替换替代料: ADS7842E/1K ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADS7842E/1K (相同外形与封装尺寸) ——差异在于 Differential Nonlinearity, Digital Interface, Integral Nonlinearity, Operating Temperature Range, Power Dissipation.
ADS7842EB/1KG4
✅ 直接替换📋 参考替代料(不在目录中)
ADS7842E/1KG4
✅ 直接替换联系询价
查看数据手册 →ADS7842E/1K 最大额定值与电气特性
| 分辨率 | 12 bit |
| Number of Input Channels | 4 channels |
| Architecture | Successive Approximation Register (SAR) |
| 采样率 | 200 ksample/s |
| Supply Voltage Range | 2.7 V to 5 V |
| Reference Voltage Range | 100 mV to VCC |
| LSB Resolution | 24 µV to 1.22 mV |
| Integral Nonlinearity | ±1 LSB |
| Differential Nonlinearity | ±1 LSB |
| Signal-to-Noise and Distortion | 72 dB SINAD |
| Power Dissipation | 2 mW |
| Digital Interface | 12-bit parallel output |
| Output Driver Type | Three-state output |
| Analog Front End | 4-channel multiplexer with sample-and-hold amplifier |
| 工作温度范围 | -40 °C to +85 °C |
| 封装 | 28-pin SSOP (DB) |
| 安装类型 | Surface mount |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
ADS7842E/1K 28-pin ssop (db) 引脚配置指南
ADS7842E/1K(28-pin ssop (db) 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: ADS7842E/1K.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADS7842E/1K 适用于 6 应用s: Portable Multi-Channel Data Logging, Industrial Process Monitoring, Test and Measurement Instrumentation, Battery-Powered Sensor Acquisition, Laboratory Data Acquisition, Embedded Control Signal Conditioning.
Portable Multi-Channel Data Logging
The ADS7842E/1K fits portable data loggers that must capture several sensor channels with low power and moderate conversion speed. Its four-channel multiplexer avoids four separate ADC packages, while 12-bit resolution provides 4096 codes across the selected reference range. The 200 ksample/s conversion rate supports changing inputs without imposing a lengthy pipeline delay. At 2 mW power dissipation and a 2.7 V minimum supply voltage, the device is suitable for battery-oriented measurement systems. Designers should match input ranges to the adjustable 100 mV-to-VCC reference and account for 24 µV to 1.22 mV LSB resolution.
推荐
Industrial Process Monitoring
The ADS7842E/1K supports industrial process-monitoring systems that combine several low-bandwidth sensors with a controller or data-acquisition module. Its four analog inputs can sample pressure, temperature, level, or position signals sequentially, while the 200 ksample/s SAR conversion rate provides responsive updates. A 2.7 V to 5 V operating range accommodates embedded control hardware, and the 12-bit result provides sufficient resolution for many supervisory measurements. The adjustable reference supports signal scaling, although a stable reference network and protected analog front end are important when field inputs experience noise or large transients.
推荐
Test and Measurement Instrumentation
The ADS7842E/1K is appropriate for bench instruments and portable test equipment that acquire up to four analog inputs through a parallel interface. Its 12-bit SAR architecture delivers predictable successive-approximation conversion behavior, and the 200 ksample/s rate is suitable for many general-purpose measurement channels. The three-state parallel outputs allow bus-oriented connection to suitable control logic, while the 28-pin SSOP package supports compact instrument layouts. Designers should use the manufacturer timing information to establish conversion and data-read cycles, particularly when multiplexing rapidly changing sources or using the lowest reference voltages.
推荐
Battery-Powered Sensor Acquisition
The ADS7842E/1K fits battery-powered sensor acquisition when several analog inputs must share a compact converter and power budget is limited. Its four-channel input multiplexer reduces component count, while 2 mW power dissipation and operation from 2.7 V support low-energy designs. The 12-bit conversion result is suitable for temperature, position, light, and other slowly changing environmental measurements. For duty-cycled logging, the system can control acquisition and reduce activity between samples. Input protection, reference stability, and calibration become important because battery voltage variation and sensor tolerances can otherwise dominate the converter’s ±1 LSB nonlinearity.
推荐
Laboratory Data Acquisition
The ADS7842E/1K can serve as the acquisition front end in a laboratory data-acquisition system using a microprocessor, FPGA, or parallel bus controller. Four multiplexed analog inputs, 12-bit resolution, and a 200 ksample/s maximum sampling rate cover routine voltage measurements and signal characterization. The parallel output reduces serial-interface overhead when samples must be transferred quickly. For bench accuracy, use a quiet, stable reference and keep analog routing compact. The converter’s 100 mV-to-VCC reference flexibility lets engineers select full-scale ranges appropriate for small sensor outputs, subject to the associated 24 µV minimum LSB step.
推荐
Embedded Control Signal Conditioning
The ADS7842E/1K is suitable for embedded control boards that must convert four analog sensor or actuator-feedback signals into digital values for a processor. Its single 2.7 V-to-5 V supply operation aligns with common embedded logic rails, and the three-state parallel outputs support connection to bus-compatible controller circuitry. The SAR conversion process and 200 ksample/s rate are adequate for feedback monitoring in many non-safety-critical control loops. Firmware must avoid changing the selected channel during an incomplete conversion, and analog input filtering should prevent out-of-band noise from folding into the selected measurement range.
推荐
推荐产品汇总
工程参考数据: ADS7842E/1K ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADS7842EB/1KG4 | ADS7842E/1KG4 | ADS7842E | ADS7842EB |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-pin SSOP (DB) | 28-pin SSOP (DB) | 28-pin SSOP (DB) | 28-pin SSOP (DB) | 28-pin SSOP (DB) |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Input Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Sampling Rate | 200 ksample/s | 200 ksample/s | 200 ksample/s | 200 ksample/s | 200 ksample/s |
| Converter Architecture | SAR | SAR | SAR | SAR | SAR |
| Digital Interface | 12-bit parallel output | 12-bit parallel output | 12-bit parallel output | 12-bit parallel output | 12-bit parallel output |
| Supply Voltage Range | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V |
| Power Dissipation | 2 mW | 2 mW | 2 mW | 2 mW | 2 mW |
关键差异点
- Combines four analog inputs with a parallel conversion interface (对比 ADS7844N)
- Maintains the full 200 ksample/s conversion rate (对比 ADS7846E)
- Supports compact 3.3 V and 5 V embedded systems (对比 ADS7842EB/1KG4)
设计说明
Place the input, reference, and supply decoupling components close to their corresponding pins. Keep the reference network compact because resistance and capacitance at REF can influence conversion accuracy and acquisition time. Route the four analog inputs away from the 12-bit parallel output bus and clock-control traces to minimize capacitive and inductive coupling into the sample-and-hold amplifier.
Use the manufacturer’s conversion timing and output enable sequence to control the three-state parallel outputs. Account for propagation delay, bus loading, and settling time before the processor samples the 12-bit result. When switching multiplexed channels, allow acquisition and conversion to complete before reading the corresponding output so residual charge on the internal sampling capacitor does not affect the new measurement.
The ADS7842E/1K operates from 2.7 V to 5 V and dissipates 2 mW under its specified operating conditions. Keep the analog and digital ground return connected according to the manufacturer layout guidance, and provide local supply bypass rather than relying on a distant bulk capacitor. If the reference is derived from VCC, assess supply noise because reference variation directly changes the full-scale range and measured LSB size.
合规信息
The product information identifies a -40 °C to +85 °C operating range and a 28-pin SSOP package, but it does not establish RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.