ADS7842E/1K - 12-Bit 4-Channel 200ksps ADC | Texas Instruments
MPN: ADS7842E/1K ✓ 啟用中ADS7842E/1K 概覽
An ADC converts an analog input voltage into a digital value suitable for processing, measurement, logging, or control. The ADS7842 belongs to the SAR ADC family, where an internal capacitor-based DAC and successive comparison determine each conversion result. Within the electronics hierarchy, it is a data-converter IC and an ADC/DAC category component designed for precision analog-signal capture. Its four-input multiplexer supports multiple sensors or measurement nodes without requiring four separate converter packages.
Key features include 12-bit resolution, a maximum sampling rate of 200 ksample/s, ±1 LSB integral and differential nonlinearity, and 72 dB SINAD. The single-supply operating range of 2.7 V to 5 V supports both 3.3 V and 5 V systems. An adjustable reference from 100 mV to VCC changes the full-scale input range and corresponding LSB resolution from 24 µV to 1.22 mV. Low power dissipation of 2 mW helps reduce system energy consumption in portable and battery-operated instruments.
The device combines a four-channel analog multiplexer, sample-and-hold amplifier, 12-bit SAR core, control logic, and three-state parallel output drivers. Parallel data output permits direct connection to appropriately buffered microprocessor or data-bus circuitry. The three-state outputs can place the bus in a high-impedance state when the converter is not selected. At 200 ksample/s, the architecture provides sufficient throughput for moderate-rate instrumentation while retaining the simple control and conversion behavior associated with SAR ADCs.
Typical uses include portable data loggers, test and measurement equipment, industrial process monitoring, battery-powered instruments, and laboratory data-acquisition systems. It is particularly useful when several analog channels must be sampled with a compact parallel-interface converter. The 200 ksample/s rate supports rapidly changing sensor signals, while the 12-bit result provides 4096 digital codes across the selected reference range.
PCB design should provide a low-impedance reference network and short analog traces to minimize acquisition errors and coupling. Decoupling capacitors should be placed close to the supply and reference pins, and digital output routing should avoid crossing sensitive input paths. Because the converter uses an adjustable reference, resistor and capacitor tolerances directly influence LSB size and calibration accuracy.
This product page combines the manufacturer specifications with practical application guidance, package details, replacement considerations, interface constraints, and PCB design notes. These engineering details help designers determine whether the ADS7842E/1K’s 12-bit resolution, four-channel multiplexing, 200 ksample/s throughput, parallel bus, and 2.7 V to 5 V supply range fit a specific data-acquisition design.
直接替換替代品,適用於 ADS7842E/1K — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ADS7842E/1K (相同外形與佔位) — 差異在於 Differential Nonlinearity, Digital Interface, Integral Nonlinearity, Operating Temperature Range, Power Dissipation.
ADS7842EB/1KG4
✅ 直接替換📋 參考替代品(不在目錄中)
ADS7842E/1KG4
✅ 直接替換聯絡詢價
查看資料表 →ADS7842E/1K 最大額定值與電氣特性
| 解析度 | 12 bit |
| Number of Input Channels | 4 channels |
| Architecture | Successive Approximation Register (SAR) |
| 取樣率 | 200 ksample/s |
| Supply Voltage Range | 2.7 V to 5 V |
| Reference Voltage Range | 100 mV to VCC |
| LSB Resolution | 24 µV to 1.22 mV |
| Integral Nonlinearity | ±1 LSB |
| Differential Nonlinearity | ±1 LSB |
| Signal-to-Noise and Distortion | 72 dB SINAD |
| Power Dissipation | 2 mW |
| Digital Interface | 12-bit parallel output |
| Output Driver Type | Three-state output |
| Analog Front End | 4-channel multiplexer with sample-and-hold amplifier |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | 28-pin SSOP (DB) |
| 安裝類型 | Surface mount |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
ADS7842E/1K 28-pin ssop (db) 腳位配置指南
ADS7842E/1K(28-pin ssop (db) 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: ADS7842E/1K.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADS7842E/1K 適用於 6 應用s: Portable Multi-Channel Data Logging, Industrial Process Monitoring, Test and Measurement Instrumentation, Battery-Powered Sensor Acquisition, Laboratory Data Acquisition, Embedded Control Signal Conditioning.
Portable Multi-Channel Data Logging
The ADS7842E/1K fits portable data loggers that must capture several sensor channels with low power and moderate conversion speed. Its four-channel multiplexer avoids four separate ADC packages, while 12-bit resolution provides 4096 codes across the selected reference range. The 200 ksample/s conversion rate supports changing inputs without imposing a lengthy pipeline delay. At 2 mW power dissipation and a 2.7 V minimum supply voltage, the device is suitable for battery-oriented measurement systems. Designers should match input ranges to the adjustable 100 mV-to-VCC reference and account for 24 µV to 1.22 mV LSB resolution.
推薦
Industrial Process Monitoring
The ADS7842E/1K supports industrial process-monitoring systems that combine several low-bandwidth sensors with a controller or data-acquisition module. Its four analog inputs can sample pressure, temperature, level, or position signals sequentially, while the 200 ksample/s SAR conversion rate provides responsive updates. A 2.7 V to 5 V operating range accommodates embedded control hardware, and the 12-bit result provides sufficient resolution for many supervisory measurements. The adjustable reference supports signal scaling, although a stable reference network and protected analog front end are important when field inputs experience noise or large transients.
推薦
Test and Measurement Instrumentation
The ADS7842E/1K is appropriate for bench instruments and portable test equipment that acquire up to four analog inputs through a parallel interface. Its 12-bit SAR architecture delivers predictable successive-approximation conversion behavior, and the 200 ksample/s rate is suitable for many general-purpose measurement channels. The three-state parallel outputs allow bus-oriented connection to suitable control logic, while the 28-pin SSOP package supports compact instrument layouts. Designers should use the manufacturer timing information to establish conversion and data-read cycles, particularly when multiplexing rapidly changing sources or using the lowest reference voltages.
推薦
Battery-Powered Sensor Acquisition
The ADS7842E/1K fits battery-powered sensor acquisition when several analog inputs must share a compact converter and power budget is limited. Its four-channel input multiplexer reduces component count, while 2 mW power dissipation and operation from 2.7 V support low-energy designs. The 12-bit conversion result is suitable for temperature, position, light, and other slowly changing environmental measurements. For duty-cycled logging, the system can control acquisition and reduce activity between samples. Input protection, reference stability, and calibration become important because battery voltage variation and sensor tolerances can otherwise dominate the converter’s ±1 LSB nonlinearity.
推薦
Laboratory Data Acquisition
The ADS7842E/1K can serve as the acquisition front end in a laboratory data-acquisition system using a microprocessor, FPGA, or parallel bus controller. Four multiplexed analog inputs, 12-bit resolution, and a 200 ksample/s maximum sampling rate cover routine voltage measurements and signal characterization. The parallel output reduces serial-interface overhead when samples must be transferred quickly. For bench accuracy, use a quiet, stable reference and keep analog routing compact. The converter’s 100 mV-to-VCC reference flexibility lets engineers select full-scale ranges appropriate for small sensor outputs, subject to the associated 24 µV minimum LSB step.
推薦
Embedded Control Signal Conditioning
The ADS7842E/1K is suitable for embedded control boards that must convert four analog sensor or actuator-feedback signals into digital values for a processor. Its single 2.7 V-to-5 V supply operation aligns with common embedded logic rails, and the three-state parallel outputs support connection to bus-compatible controller circuitry. The SAR conversion process and 200 ksample/s rate are adequate for feedback monitoring in many non-safety-critical control loops. Firmware must avoid changing the selected channel during an incomplete conversion, and analog input filtering should prevent out-of-band noise from folding into the selected measurement range.
推薦
推薦產品摘要
工程參考資料,適用於 ADS7842E/1K — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADS7842EB/1KG4 | ADS7842E/1KG4 | ADS7842E | ADS7842EB |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-pin SSOP (DB) | 28-pin SSOP (DB) | 28-pin SSOP (DB) | 28-pin SSOP (DB) | 28-pin SSOP (DB) |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Input Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Sampling Rate | 200 ksample/s | 200 ksample/s | 200 ksample/s | 200 ksample/s | 200 ksample/s |
| Converter Architecture | SAR | SAR | SAR | SAR | SAR |
| Digital Interface | 12-bit parallel output | 12-bit parallel output | 12-bit parallel output | 12-bit parallel output | 12-bit parallel output |
| Supply Voltage Range | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V |
| Power Dissipation | 2 mW | 2 mW | 2 mW | 2 mW | 2 mW |
主要差異化特點
- Combines four analog inputs with a parallel conversion interface (對比ADS7844N)
- Maintains the full 200 ksample/s conversion rate (對比ADS7846E)
- Supports compact 3.3 V and 5 V embedded systems (對比ADS7842EB/1KG4)
設計說明
Place the input, reference, and supply decoupling components close to their corresponding pins. Keep the reference network compact because resistance and capacitance at REF can influence conversion accuracy and acquisition time. Route the four analog inputs away from the 12-bit parallel output bus and clock-control traces to minimize capacitive and inductive coupling into the sample-and-hold amplifier.
Use the manufacturer’s conversion timing and output enable sequence to control the three-state parallel outputs. Account for propagation delay, bus loading, and settling time before the processor samples the 12-bit result. When switching multiplexed channels, allow acquisition and conversion to complete before reading the corresponding output so residual charge on the internal sampling capacitor does not affect the new measurement.
The ADS7842E/1K operates from 2.7 V to 5 V and dissipates 2 mW under its specified operating conditions. Keep the analog and digital ground return connected according to the manufacturer layout guidance, and provide local supply bypass rather than relying on a distant bulk capacitor. If the reference is derived from VCC, assess supply noise because reference variation directly changes the full-scale range and measured LSB size.
合規資訊
The product information identifies a -40 °C to +85 °C operating range and a 28-pin SSOP package, but it does not establish RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.