INA253A3IPW - 400mV/A Bidirectional Current Sense | Texas Instruments
料号: INA253A3IPW ✓ 量产中INA253A3IPW 概述
A current-shunt monitor is an instrumentation amplifier that measures the small voltage generated across a precision shunt resistor as current flows through a conductor. The INA253 belongs to the current-sense amplifier hierarchy, where the amplified shunt voltage is filtered, digitized, or used for power monitoring and control. Its integrated resistor simplifies the sensing path, reduces external component count, and keeps the shunt geometry close to the amplifier for improved measurement repeatability.
The A3 gain option provides 400 mV/A, while the INA253 family also includes 100 mV/A and 200 mV/A versions. The device operates over a -4 V to +80 V common-mode range, independent of its supply voltage, which supports high-side sensing in 48 V industrial, communications, automotive, and power-system environments. Its 350 kHz -3 dB bandwidth accommodates dynamic current measurements while providing rejection of PWM-related disturbances.
The INA253A3IPW combines precision zero-drift signal conditioning with an integrated 2 mΩ shunt. Bidirectional operation allows the output to move above or below ground depending on current direction. The listed operating-temperature range is -40°C to +125°C, and the device is supplied in a 20-pin TSSOP package measuring 0.173 inch, or 4.40 mm, in width.
Typical uses include server and telecom power rails, industrial motor controls, battery-management systems, LED drivers, solenoid drivers, and automotive load monitoring. In each application, the shunt monitor converts bidirectional current into a proportional analog voltage, allowing a controller to monitor load current, detect overcurrent, or implement closed-loop power management.
PCB layout is critical because the integrated shunt and amplifier must be placed directly in the current path. High-current conductors should use short, wide copper, while the supply and ground connections should follow the manufacturer’s pin-assignment and layout guidance. Designers should also account for output settling, filter selection, and common-mode transient protection when operating near rapidly switching power stages.
This product page combines the exact ordering information, electrical characteristics, family-level comparison, and application guidance needed to plan an INA253A3-based current-measurement design. It also identifies which same-package alternatives can be evaluated when gain, automotive qualification, or supply requirements differ.
直接替换替代料: INA253A3IPW ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: INA253A3IPW (相同外形与封装尺寸) ——差异在于 Common-Mode Voltage Range, Gain, Operating Temperature Range, Output Type, PWM Rejection.
INA253A3QPWRQ1
✅ 直接替换📋 参考替代料(不在目录中)
INA253A1IPW
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →INA253A2IPW
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →INA253A4IPW
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
INA253A1QPWRQ1
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
INA253A2QPWRQ1
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
INA253A3IPW 最大额定值与电气特性
| Device Type | Bidirectional zero-drift current-shunt monitor with integrated shunt resistor |
| Number of Channels | 1 circuit |
| Gain | 400 mV/A |
| Common-Mode Voltage Range | -4 V to +80 V |
| Integrated Shunt Resistance | 2 mΩ |
| Shunt Characteristics | Precision, low-inductive integrated resistor |
| Signal Direction | Bidirectional |
| Amplifier Architecture | Zero-drift chopped amplifier |
| PWM Rejection | Supported |
| Signal Bandwidth | 350 kHz -3 dB |
| Slew Rate | 2.4 V/µs |
| 工作温度范围 | -40°C to +125°C |
| 封装 | 20-pin TSSOP, 0.173 inch (4.40 mm) width |
| 安装类型 | Surface mount |
| 输出类型 | Voltage output |
INA253A3IPW 20-pin tssop, 0.173 inch (4.40 mm) width 引脚配置指南
INA253A3IPW(20-pin tssop, 0.173 inch (4.40 mm) width 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: INA253A3IPW.
请参阅 数据手册 以查看完整引脚配置。
典型应用
INA253A3IPW 适用于 6 应用s: 48V Industrial Power-Rail Monitoring, Server and Telecom PSU Current Sensing, Bidirectional Battery-Charge Monitoring, Motor and Solenoid Driver Control, Automotive Electrical-Load Monitoring, LED Driver and Lighting Load Regulation.
48V Industrial Power-Rail Monitoring
The INA253A3IPW fits high-side current measurement in 48 V industrial systems because its shunt input supports a -4 V to +80 V common-mode range and the integrated 2 mΩ resistor removes the need for an external precision shunt. The 400 mV/A gain converts 1 A into a 400 mV output signal, improving utilization of an ADC input near zero current. Place the device directly in the power path and use short, wide copper to minimize added resistance. Bidirectional operation is useful when the monitored conductor can source or sink current, while the 350 kHz bandwidth supports control loops faster than conventional slow current sensors.
推荐
Server and Telecom PSU Current Sensing
The INA253A3IPW is suitable for measuring current in server, storage, and telecommunications power supplies where fault detection and load regulation require accurate feedback. Its 400 mV/A gain produces 400 mV at 1 A, allowing a controller to detect overloads without operating near the amplifier’s full-scale output at relatively low current. The integrated 2 mΩ shunt simplifies the power path and reduces board area, while the -4 V to +80 V common-mode range covers positive high-side rails. Designers should still include filtering appropriate to the switching environment and verify the output range against the ADC and supply rails.
推荐
Bidirectional Battery-Charge Monitoring
The INA253A3IPW can measure charge and discharge current in battery-management systems because its bidirectional output represents both current directions around the zero-current point. The 400 mV/A gain provides useful resolution for low-current balancing, diagnostics, and system power-flow control. Its integrated 2 mΩ shunt avoids mismatches between a discrete shunt and amplifier input, while the broad common-mode range supports batteries and buses operating within -4 V to +80 V. Layout the shunt path as a compact two-conductor loop, place the supply bypass capacitor close to the device, and confirm that the selected gain remains within the output range at maximum charge or discharge current.
推荐
Motor and Solenoid Driver Control
The INA253A3IPW suits motor-control and solenoid-driver feedback loops where the controller must observe load current rapidly and respond to overcurrent. Its 350 kHz -3 dB bandwidth and 2.4 V/µs slew rate provide substantially more bandwidth than many slow current sensors. The 400 mV/A gain produces a strong control signal, and the integrated shunt reduces external sensing-component count. In pulse-width-modulated power stages, use the amplifier’s PWM-rejection characteristics to preserve measurement fidelity. Keep the current path and shunt terminals away from high-dV/dt switch-node copper, and provide local supply bypassing to prevent injected noise from disturbing the control signal.
推荐
Automotive Electrical-Load Monitoring
The INA253 family is applicable to automotive electrical-load monitoring because the INA253A3IPW combines a wide -4 V to +80 V common-mode range with an integrated precision shunt. The 400 mV/A gain allows a controller to detect small load changes in battery-powered systems, and bidirectional sensing covers both charging and load current. The 20-pin TSSOP package supports compact control boards, while the -40°C to +125°C rating supports a broad environmental range. For a production automotive design, evaluate the Q1 ordering option when automotive qualification is required, and verify transient protection, ISO 7637-related design guidance, and all absolute-maximum limits in the manufacturer documentation.
推荐
LED Driver and Lighting Load Regulation
The INA253A3IPW can provide load-current feedback in LED drivers and regulated lighting systems where constant-current performance and short-circuit protection are important. The 400 mV/A gain creates 400 mV at 1 A, giving a controller useful resolution for regulating moderate LED strings and detecting overloads. The integrated 2 mΩ shunt simplifies the current-sense network, while the broad common-mode range allows the sense element to remain in a high-side rail above the amplifier supply. Account for the bidirectional measurement range during startup and reverse-current conditions, verify the amplifier’s output swing at maximum current, and isolate switch-node routing from the sense path to maintain accuracy.
推荐
推荐产品汇总
工程参考数据: INA253A3IPW ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | INA253A3QPWRQ1 | INA253A1IPW | INA253A2IPW | INA253A4IPW | INA253A1QPWRQ1 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 20-TSSOP | 20-TSSOP - same package | 20-TSSOP - same package | 20-TSSOP - same package | 20-TSSOP - same package | 20-TSSOP - same package |
| Integrated Shunt Resistance | 2 mΩ | 2 mΩ | 2 mΩ | 2 mΩ | 2 mΩ | 2 mΩ |
| Current Direction | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional |
| Signal Conditioning | Zero-drift chopped amplifier with PWM rejection | Zero-drift chopped amplifier with PWM rejection | Zero-drift chopped amplifier with PWM rejection | Zero-drift chopped amplifier with PWM rejection | Zero-drift chopped amplifier with PWM rejection | Zero-drift chopped amplifier with PWM rejection |
关键差异点
- Highest standard-family gain option used in the comparison (对比 INA253A2IPW)
- Integrated precision shunt simplifies the sensing path (对比 INA240A4DR)
- Wide common-mode range enables high-side sensing above the supply (对比 INA253A1IPW)
- Automotive-qualified family option retains the A3 gain (对比 INA253A3IPW)
设计说明
Place the INA253A3IPW directly in the high-current path and minimize copper length between the integrated shunt terminals and the load. Use short, wide conductors so PCB resistance adds as little error as possible to the 2 mΩ integrated shunt. Follow the Texas Instruments INA253 layout guidance for the shunt-current geometry and keep high-dV/dt switch-node copper physically separated from the amplifier inputs and output.
Route supply and ground connections directly to the device and place the recommended bypass capacitor close to the corresponding pins. Keep the sensitive analog output trace away from power inductors, switch nodes, and high-current return paths. Because the amplifier uses zero-drift signal conditioning, preserve a quiet ground reference and avoid adding unnecessary loops that can increase pickup of PWM-related noise.
Do not treat the -4 V to +80 V common-mode rating as the amplifier supply rating; these are separate limits. Before operation, verify the INA253A3IPW supply range, output swing, absolute-maximum ratings, and the output range of the connected ADC. At 400 mV/A, a 10 A current produces a 4 V sense output, so the downstream circuitry must support that voltage without clipping or violating its input limits.
The 350 kHz -3 dB bandwidth and 2.4 V/µs slew rate support dynamic current measurements, but additional output filtering can add phase delay in a control loop. If the INA253A3IPW drives an ADC, select a filter that preserves the required response time while attenuating switching ripple. Validate the complete current-to-digital path for settling, noise, and overload recovery before closing the control loop.
合规信息
The INA253A3QPWRQ1 ordering option is identified as a Q1 automotive variant, but no explicit compliance declaration for INA253A3IPW is included in the verified product information.