INA253A3IPW - 400mV/A Bidirectional Current Sense | Texas Instruments
N.º de pieza: INA253A3IPW ✓ ActivoINA253A3IPW Descripción general
A current-shunt monitor is an instrumentation amplifier that measures the small voltage generated across a precision shunt resistor as current flows through a conductor. The INA253 belongs to the current-sense amplifier hierarchy, where the amplified shunt voltage is filtered, digitized, or used for power monitoring and control. Its integrated resistor simplifies the sensing path, reduces external component count, and keeps the shunt geometry close to the amplifier for improved measurement repeatability.
The A3 gain option provides 400 mV/A, while the INA253 family also includes 100 mV/A and 200 mV/A versions. The device operates over a -4 V to +80 V common-mode range, independent of its supply voltage, which supports high-side sensing in 48 V industrial, communications, automotive, and power-system environments. Its 350 kHz -3 dB bandwidth accommodates dynamic current measurements while providing rejection of PWM-related disturbances.
The INA253A3IPW combines precision zero-drift signal conditioning with an integrated 2 mΩ shunt. Bidirectional operation allows the output to move above or below ground depending on current direction. The listed operating-temperature range is -40°C to +125°C, and the device is supplied in a 20-pin TSSOP package measuring 0.173 inch, or 4.40 mm, in width.
Typical uses include server and telecom power rails, industrial motor controls, battery-management systems, LED drivers, solenoid drivers, and automotive load monitoring. In each application, the shunt monitor converts bidirectional current into a proportional analog voltage, allowing a controller to monitor load current, detect overcurrent, or implement closed-loop power management.
PCB layout is critical because the integrated shunt and amplifier must be placed directly in the current path. High-current conductors should use short, wide copper, while the supply and ground connections should follow the manufacturer’s pin-assignment and layout guidance. Designers should also account for output settling, filter selection, and common-mode transient protection when operating near rapidly switching power stages.
This product page combines the exact ordering information, electrical characteristics, family-level comparison, and application guidance needed to plan an INA253A3-based current-measurement design. It also identifies which same-package alternatives can be evaluated when gain, automotive qualification, or supply requirements differ.
Alternativas directas para INA253A3IPW — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con INA253A3IPW (mismo factor de forma y huella) — difiere en Common-Mode Voltage Range, Gain, Operating Temperature Range, Output Type, PWM Rejection.
INA253A3QPWRQ1
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
INA253A1IPW
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →INA253A2IPW
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →INA253A4IPW
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
INA253A1QPWRQ1
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
INA253A2QPWRQ1
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
INA253A3IPW Valores máximos y características eléctricas
| Device Type | Bidirectional zero-drift current-shunt monitor with integrated shunt resistor |
| Number of Channels | 1 circuit |
| Gain | 400 mV/A |
| Common-Mode Voltage Range | -4 V to +80 V |
| Integrated Shunt Resistance | 2 mΩ |
| Shunt Characteristics | Precision, low-inductive integrated resistor |
| Signal Direction | Bidirectional |
| Amplifier Architecture | Zero-drift chopped amplifier |
| PWM Rejection | Supported |
| Signal Bandwidth | 350 kHz -3 dB |
| Slew Rate | 2.4 V/µs |
| Rango de temperatura de funcionamiento | -40°C to +125°C |
| Encapsulado | 20-pin TSSOP, 0.173 inch (4.40 mm) width |
| Tipo de montaje | Surface mount |
| Tipo de salida | Voltage output |
Guía de configuración de pines de INA253A3IPW 20-pin tssop, 0.173 inch (4.40 mm) width
Configuración de pines para INA253A3IPW (encapsulado 20-pin tssop, 0.173 inch (4.40 mm) width). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para INA253A3IPW.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
INA253A3IPW es adecuado para 6 aplicacións: 48V Industrial Power-Rail Monitoring, Server and Telecom PSU Current Sensing, Bidirectional Battery-Charge Monitoring, Motor and Solenoid Driver Control, Automotive Electrical-Load Monitoring, LED Driver and Lighting Load Regulation.
48V Industrial Power-Rail Monitoring
The INA253A3IPW fits high-side current measurement in 48 V industrial systems because its shunt input supports a -4 V to +80 V common-mode range and the integrated 2 mΩ resistor removes the need for an external precision shunt. The 400 mV/A gain converts 1 A into a 400 mV output signal, improving utilization of an ADC input near zero current. Place the device directly in the power path and use short, wide copper to minimize added resistance. Bidirectional operation is useful when the monitored conductor can source or sink current, while the 350 kHz bandwidth supports control loops faster than conventional slow current sensors.
Recomendado
Server and Telecom PSU Current Sensing
The INA253A3IPW is suitable for measuring current in server, storage, and telecommunications power supplies where fault detection and load regulation require accurate feedback. Its 400 mV/A gain produces 400 mV at 1 A, allowing a controller to detect overloads without operating near the amplifier’s full-scale output at relatively low current. The integrated 2 mΩ shunt simplifies the power path and reduces board area, while the -4 V to +80 V common-mode range covers positive high-side rails. Designers should still include filtering appropriate to the switching environment and verify the output range against the ADC and supply rails.
Recomendado
Bidirectional Battery-Charge Monitoring
The INA253A3IPW can measure charge and discharge current in battery-management systems because its bidirectional output represents both current directions around the zero-current point. The 400 mV/A gain provides useful resolution for low-current balancing, diagnostics, and system power-flow control. Its integrated 2 mΩ shunt avoids mismatches between a discrete shunt and amplifier input, while the broad common-mode range supports batteries and buses operating within -4 V to +80 V. Layout the shunt path as a compact two-conductor loop, place the supply bypass capacitor close to the device, and confirm that the selected gain remains within the output range at maximum charge or discharge current.
Recomendado
Motor and Solenoid Driver Control
The INA253A3IPW suits motor-control and solenoid-driver feedback loops where the controller must observe load current rapidly and respond to overcurrent. Its 350 kHz -3 dB bandwidth and 2.4 V/µs slew rate provide substantially more bandwidth than many slow current sensors. The 400 mV/A gain produces a strong control signal, and the integrated shunt reduces external sensing-component count. In pulse-width-modulated power stages, use the amplifier’s PWM-rejection characteristics to preserve measurement fidelity. Keep the current path and shunt terminals away from high-dV/dt switch-node copper, and provide local supply bypassing to prevent injected noise from disturbing the control signal.
Recomendado
Automotive Electrical-Load Monitoring
The INA253 family is applicable to automotive electrical-load monitoring because the INA253A3IPW combines a wide -4 V to +80 V common-mode range with an integrated precision shunt. The 400 mV/A gain allows a controller to detect small load changes in battery-powered systems, and bidirectional sensing covers both charging and load current. The 20-pin TSSOP package supports compact control boards, while the -40°C to +125°C rating supports a broad environmental range. For a production automotive design, evaluate the Q1 ordering option when automotive qualification is required, and verify transient protection, ISO 7637-related design guidance, and all absolute-maximum limits in the manufacturer documentation.
Recomendado
LED Driver and Lighting Load Regulation
The INA253A3IPW can provide load-current feedback in LED drivers and regulated lighting systems where constant-current performance and short-circuit protection are important. The 400 mV/A gain creates 400 mV at 1 A, giving a controller useful resolution for regulating moderate LED strings and detecting overloads. The integrated 2 mΩ shunt simplifies the current-sense network, while the broad common-mode range allows the sense element to remain in a high-side rail above the amplifier supply. Account for the bidirectional measurement range during startup and reverse-current conditions, verify the amplifier’s output swing at maximum current, and isolate switch-node routing from the sense path to maintain accuracy.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para INA253A3IPW — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | INA253A3QPWRQ1 | INA253A1IPW | INA253A2IPW | INA253A4IPW | INA253A1QPWRQ1 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 20-TSSOP | 20-TSSOP - same package | 20-TSSOP - same package | 20-TSSOP - same package | 20-TSSOP - same package | 20-TSSOP - same package |
| Integrated Shunt Resistance | 2 mΩ | 2 mΩ | 2 mΩ | 2 mΩ | 2 mΩ | 2 mΩ |
| Current Direction | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional |
| Signal Conditioning | Zero-drift chopped amplifier with PWM rejection | Zero-drift chopped amplifier with PWM rejection | Zero-drift chopped amplifier with PWM rejection | Zero-drift chopped amplifier with PWM rejection | Zero-drift chopped amplifier with PWM rejection | Zero-drift chopped amplifier with PWM rejection |
Diferenciadores clave
- Highest standard-family gain option used in the comparison (frente a INA253A2IPW)
- Integrated precision shunt simplifies the sensing path (frente a INA240A4DR)
- Wide common-mode range enables high-side sensing above the supply (frente a INA253A1IPW)
- Automotive-qualified family option retains the A3 gain (frente a INA253A3IPW)
Notas de diseño
Place the INA253A3IPW directly in the high-current path and minimize copper length between the integrated shunt terminals and the load. Use short, wide conductors so PCB resistance adds as little error as possible to the 2 mΩ integrated shunt. Follow the Texas Instruments INA253 layout guidance for the shunt-current geometry and keep high-dV/dt switch-node copper physically separated from the amplifier inputs and output.
Route supply and ground connections directly to the device and place the recommended bypass capacitor close to the corresponding pins. Keep the sensitive analog output trace away from power inductors, switch nodes, and high-current return paths. Because the amplifier uses zero-drift signal conditioning, preserve a quiet ground reference and avoid adding unnecessary loops that can increase pickup of PWM-related noise.
Do not treat the -4 V to +80 V common-mode rating as the amplifier supply rating; these are separate limits. Before operation, verify the INA253A3IPW supply range, output swing, absolute-maximum ratings, and the output range of the connected ADC. At 400 mV/A, a 10 A current produces a 4 V sense output, so the downstream circuitry must support that voltage without clipping or violating its input limits.
The 350 kHz -3 dB bandwidth and 2.4 V/µs slew rate support dynamic current measurements, but additional output filtering can add phase delay in a control loop. If the INA253A3IPW drives an ADC, select a filter that preserves the required response time while attenuating switching ripple. Validate the complete current-to-digital path for settling, noise, and overload recovery before closing the control loop.
Información de cumplimiento
The INA253A3QPWRQ1 ordering option is identified as a Q1 automotive variant, but no explicit compliance declaration for INA253A3IPW is included in the verified product information.