LM2904BIDGKR - Dual 36V 1.2MHz Op Amp | Texas Instruments
料号: LM2904BIDGKR ✓ 量产中LM2904BIDGKR 概述
An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its inverting and non-inverting inputs. The dual architecture provides two independent amplifiers in one package, making the LM2904B suitable for signal conditioning, current monitoring, filtering, and general feedback-control circuits. Its position in the signal-chain hierarchy is operational amplifier, analog amplifier, analog integrated circuit, and semiconductor.
The LM2904B version provides a 3 V to 36 V operating supply range, a 1.2 MHz gain-bandwidth product, and a 0.5 V/us slew rate. The improved LM2904B family also features enhanced ESD protection relative to the original LM2904 family. These characteristics make it suitable for industrial control systems and other applications operating from industrial supply rails.
Two independent amplifier channels are provided in a compact 8-pin surface-mount package. The wide supply range allows operation from a single low-voltage rail or from split positive and negative supplies when the circuit requires them. The device is intended for general-purpose applications rather than precision instrumentation, where very low offset voltage and very low bias current would be required.
Typical uses include transducer and sensor signal conditioning, low-frequency active filters, audio and communications interface circuits, voltage monitoring, and process-control loops. Industrial instrumentation is a natural fit because the specified operating temperature reaches 125C. The 1.2 MHz bandwidth supports lower-frequency precision and control tasks rather than high-speed video or RF applications.
When designing the circuit, verify input and output common-mode limits at the selected supply voltage and provide adequate output-current headroom for the load and feedback network. Decoupling capacitors should be placed close to the supply pins, and the unused amplifier channel should be configured with inputs tied to a valid common-mode voltage rather than left floating.
This page consolidates package, temperature, electrical-performance, and cross-reference information into an engineering-focused selection guide. It also documents verified drop-in relationships, practical layout guidance, application use cases, and parameter-level comparisons that help shorten design evaluation time.
直接替换替代料: LM2904BIDGKR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2904BIDGKR (相同外形与封装尺寸) ——差异在于 Amplifier Type, Gain-Bandwidth Product, Maximum Supply Voltage.
LM2904DGKR
✅ 直接替换联系询价
查看数据手册 →LM2904BIDGKR 最大额定值与电气特性
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Circuits | 2 circuits |
| Maximum Supply Voltage | 36 V |
| Operating Supply Voltage Range | 3 V to 36 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/us |
| 工作温度范围 | -40C to +125C |
| Package Type | 8-pin VSSOP (DGK) |
| 安装类型 | Surface mount |
| Package Pin Count | 8 pins |
| ESD Protection | Improved ESD protection |
LM2904BIDGKR 8 pins 引脚配置指南
LM2904BIDGKR(8 pins 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LM2904BIDGKR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LM2904BIDGKR 适用于 6 应用s: Industrial Sensor Signal Conditioning, Process Control Feedback Loops, Low-Frequency Active Filters, Audio Preamplification and Buffering, Voltage Monitoring and Threshold Detection, Communications Interface Conditioning.
Industrial Sensor Signal Conditioning
The LM2904BIDGKR suits analog sensor interfaces that require two amplifiers within one compact package. Its 3 V to 36 V operating range accommodates industrial rails, while the -40C to +125C specification supports temperature-varying equipment. The 1.2 MHz gain-bandwidth product is sufficient for many pressure, temperature, and position sensors whose bandwidth is well below the amplifier limit. Place the amplifier close to the sensor connector, use short input traces, and bypass the supply pins locally to reduce noise coupled into high-impedance sensor lines.
推荐
Process Control Feedback Loops
In control and instrumentation loops, the LM2904BIDGKR can provide error amplification, current-to-voltage conversion, and active filtering around a controller. Two independent channels allow a design to combine a sensor amplifier with an output driver or buffer. The 0.5 V/us slew rate supports low- and mid-frequency control signals, while the 36 V supply rating provides headroom for actuator interfaces. Check the common-mode range and output swing against the loop operating region, and place compensation components close to the amplifier inputs.
推荐
Low-Frequency Active Filters
The LM2904BIDGKR is appropriate for first- and second-order active filters built around the Sallen-Key or multiple-feedback topologies. Its 1.2 MHz gain-bandwidth product gives ample loop-gain margin for filters whose corner frequencies remain far lower than the amplifier bandwidth. Matching resistor and capacitor values is important for accurate cutoff and gain, so use a consistent tolerance for paired components. Keep the passive network close to the amplifier pins and provide a clean ground return to reduce sensitivity to external interference.
推荐
Audio Preamplification and Buffering
The LM2904BIDGKR can buffer or preamplify low-level audio signals when the required bandwidth is compatible with its 1.2 MHz gain-bandwidth product. The dual configuration supports balanced or stereo buffering without requiring two packages, and the wide 36 V supply rating permits operation from higher-voltage audio rails. Select feedback values for the intended closed-loop gain, confirm output swing at the selected supply voltage, and reference the manufacturer's stability guidance before adding large capacitive loads at the output.
推荐
Voltage Monitoring and Threshold Detection
The LM2904BIDGKR is useful for amplifying a scaled sense voltage and comparing it with a reference through an external feedback network. Its two channels can handle both the sensing amplifier and threshold amplifier, while the 3 V to 36 V range accommodates supply-derived signals. Ensure the sense-node voltage remains inside the input common-mode range and account for input offset voltage when setting a precision threshold. A physical-noise margin between the operating point and threshold helps prevent repeated switching near the transition.
推荐
Communications Interface Conditioning
The LM2904BIDGKR can condition slow communications, receiver, or modem signals where a wide supply range and industrial temperature operation are priorities. It is better suited to baseband and supervisory functions than to high-speed line drivers, because the gain-bandwidth product is 1.2 MHz. The dual channels allow receiver amplification and filtering in a compact area. Maintain controlled impedance paths from the connector or transceiver, guard sensitive input nodes from switching sources, and verify that the interface amplitude fits the amplifier's common-mode and output-swing limits.
推荐
工程参考数据: LM2904BIDGKR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2904DGKR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) |
| Number of Amplifier Channels | 2 | 2 |
关键差异点
- Improved ESD capability within the LM2904B family (对比 LM2904DGKR)
- Wide operating temperature coverage (对比 LM2904DGKR)
- Dual general-purpose amplifier in a compact footprint (对比 LM2904DGKR)
- Higher documented gain-bandwidth product for general-purpose designs (对比 LM2904DGKR)
设计说明
Place the supply bypass capacitor directly beside the LM2904BIDGKR power and ground pins, and keep the loop formed by the capacitor, device pins, and ground return as small as practical. Sensitive non-inverting inputs should face away from the supply capacitor and switching-current paths. For source signals with high source impedance, keep the input traces short and consider guarding the unused channel so that board leakage does not affect the active measurement.
Do not operate the amplifier outside the 3 V to 36 V supply range or assume that the full input range is available at every supply voltage. Confirm the common-mode input range, output swing, and input offset against the circuit's minimum and maximum signal conditions. Tie both inputs of an unused channel to a valid common-mode voltage rather than leaving them open. Also avoid placing a large capacitive load directly on the output unless the configuration has been checked for stability.
The 1.2 MHz gain-bandwidth product limits the useful small-signal bandwidth, while the 0.5 V/us slew rate constrains large-signal transitions. Keep closed-loop bandwidth well below the gain-bandwidth product to maintain phase margin, and verify whether the required output amplitude and frequency combination violates the slew-rate limit. Use a grounded reference plane for analog signals, avoid routing sensitive inputs beneath digital or switching nets, and maintain a continuous return path beneath each high-impedance input trace.
The power dissipation is primarily determined by quiescent current, load current, and the voltage dropped across each amplifier channel. For a basic estimate, calculate channel dissipation as the closed-loop output swing multiplied by output current, then add the supply contribution associated with quiescent current: P_channel = VOUT x IOUT + (VS - VOUT) x IQ. Compare the resulting total with the package and board thermal limits, then reduce it through lower supply voltage, lower output current, lower quiescent current, or additional copper area.
合规信息
The available manufacturer and distributor listings do not state the individual compliance declarations for this exact orderable MPN. Confirm RoHS, REACH, halogen-free, conflict-minerals, and automotive-qualification status against the current manufacturer documentation or declaration before release.