MPC8536EBVTAVLA - PowerQUICC III 1.5GHz e500 SoC | NXP
料号： MPC8536EBVTAVLA ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $229.14 | $229.14 |
| 10 | $206.23 | $2,062.30 |
| 100 | $183.31 | $18,331.00 |
| 500 | $164.98 | $82,490.00 |
| 1,000 | $152.76 | $152,760.00 |
MPC8536EBVTAVLA 概述
A PowerQUICC III processor is a system-on-chip (SoC) designed for high-performance embedded networking and communications. It sits within the broader category of communications processors (CPUs/MPUs with integrated peripherals), which are themselves a sub-category of microprocessors (MPU) and ultimately integrated circuits (semiconductor devices). This hierarchy matters because selecting a PowerQUICC III part implies a need for high I/O integration, deterministic networking performance, and Power Architecture toolchain compatibility rather than raw application-processor throughput.
Key features include a 36-bit physical address space, integrated security engine (SEC) for hardware-accelerated encryption, four GbE controllers, multiple PCI Express lanes, two SATA ports, USB 2.0, SDHC boot interface, and dedicated QUICC Engine technology. The 1.5 GHz core pairs with dual DDR2/DDR3 memory controllers supporting up to 800 MT/s data rates, enabling sustained multi-gigabit throughput in router and gateway workloads.
Architecturally, the MPC8536E uses a hierarchical bus topology where the e500 core feeds a coherency fabric connecting the L2 cache, DDR controllers, and high-speed serial interfaces (PCIe, SATA, SerDes). The integrated QUICC Engine offloads packet processing, while the SEC block accelerates DES/3DES/AES/SHA operations. Process technology and fabrication details are documented in the NXP MPC8536E datasheet family.
Typical applications include enterprise routers, network attached storage (NAS), industrial gateways, security appliances, and industrial automation controllers. The 0C to 105C operating temperature range supports telco and industrial deployments. Reference designs typically combine this MPN with DDR3 SDRAM, NOR/NAND flash, and Ethernet PHYs such as the Vitesse/Marvell VSC8512 or Broadcom BCM5461.
When designing with this part, allocate sufficient PCB layers for the FCBGA breakout, simulate DDR3 signal integrity rigorously, and provision adequate thermal relief under the 29x29 mm package. The high-speed SerDes lanes require length-matched routing and controlled-impedance stack-up to meet PCIe and SATA compliance.
This page consolidates distributor pricing across DigiKey, Mouser, and Octopart, drop-in replacement candidates from the PowerQUICC family, and practical design notes not found in the manufacturer datasheet.
直接替换替代料： MPC8536EBVTAVLA ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MPC8536EBVTAVLA （相同外形与封装尺寸） ——差异在于 Ethernet, Manufacturer, Operating Temperature, Package, Mounting Type.
快速对比工具——选择替代料号进行并排对比：
MPC8536EBVJAVLA
✅ 直接替换📋 参考替代料（不在目录中）
MPC8536ECVJAVLA
✅ 直接替换📋 参考替代料（不在目录中）
MPC8536EBVTAULA
✅ 直接替换✓ 有现货
$199.5 / 个
查看数据手册 →MPC8536EBVTANLA
✅ 直接替换📋 参考替代料（不在目录中）
MPC8536EAVTAVLA
✅ 直接替换✓ 有现货
$72 / 个
查看数据手册 →MPC8536EBVTAVLA 最大额定值与电气特性
| Manufacturer | NXP Semiconductors (formerly Freescale) |
| Part Family | PowerQUICC III / MPC85xx |
| Core Architecture | PowerPC e500 (32-bit, Power Architecture technology) |
| Maximum Core Frequency | 1.5 GHz |
| Number of Cores | 1 |
| 数据总线宽度 | 32-bit |
| Physical Address Space | 36-bit |
| DDR Memory Controller | DDR2/DDR3, dual-channel, up to 800 MT/s |
| Integrated Peripherals | PCIe, SATA, GbE (x4), SDHC, USB 2.0 |
| Security Engine (SEC) | Yes - DES/3DES/AES/SHA hardware acceleration |
| QUICC Engine | Yes - packet processing offload |
| 电源电压 | 1.1 V core (with multiple auxiliary rails) |
| 封装 | 783-FCPBGA (29x29 mm, 1 mm pitch, 2.80 mm height) |
| Lead-Free / RoHS | Lead-free, RoHS compliant per FCBGA package marking |
| 工作温度 | 0 C to 105 C |
| 安装类型 | Surface Mount (BGA) |
| Clock Speed (Fabric) | 133 MHz platform / 1.5 GHz core |
MPC8536EBVTAVLA 783-fcpbga (29x29 mm, 1 mm pitch, 2.80 mm height) 引脚配置指南
MPC8536EBVTAVLA（783-fcpbga (29x29 mm, 1 mm pitch, 2.80 mm height) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： MPC8536EBVTAVLA.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MPC8536EBVTAVLA 适用于 7 应用s: Enterprise Routers and Edge Gateways, Network Attached Storage (NAS), Industrial Gateways and Protocol Converters, Security Appliances (VPN, Firewall, UTM), Multi-Function Printers and Imaging Platforms, Telecom Control Plane and Baseband Equipment, Automotive Ethernet Gateways and Infotainment.
Enterprise Routers and Edge Gateways
The MPC8536EBVTAVLA fits enterprise router design because its 1.5 GHz e500 core plus QUICC Engine offload deliver multi-gigabit routing throughput while keeping BOM cost low. Its four integrated Gigabit Ethernet MACs map directly to WAN-edge and LAN-side switch fabrics, eliminating external MACs. The hardware SEC block accelerates IPSec at line rate, critical for VPN concentrator and SDN edge nodes. With DDR2/DDR3 up to 800 MT/s, sustained packet forwarding does not starve the CPU. Designers typically pair this MPN with Vitesse/Marvell VSC8512 PHYs and external DDR3-800 SODIMMs.
推荐
Network Attached Storage (NAS)
In NAS platforms the MPC8536EBVTAVLA serves as both storage controller and network interface. Its dual SATA ports drive two 3.5 inch HDDs directly with NCQ and port multiplier support, while the PCIe x4 lane connects to a RAID accelerator card. The SDHC boot interface simplifies OS and firmware deployment, and the SEC engine offloads AES-256 for encrypted-at-rest volumes. DDR3 support up to 800 MT/s provides the bandwidth required for 4K sequential reads over bonded GbE links.
推荐
Industrial Gateways and Protocol Converters
Industrial protocol gateways benefit from the MPC8536EBVTAVLA's combination of GbE, USB 2.0, SDHC, and the QUICC Engine, which can run Modbus TCP, EtherCAT, PROFINET, and other industrial protocols concurrently. The 0C to 105C operating range tolerates factory-floor enclosures. The e500 core's deterministic interrupt latency suits real-time control loops, while the SEC block secures MQTT and OPC UA traffic. Designers typically flash Linux with PREEMPT_RT for sub-millisecond response times.
推荐
Security Appliances (VPN, Firewall, UTM)
For VPN and unified threat management (UTM) appliances, the MPC8536EBVTAVLA's hardware SEC engine accelerates AES-256-CBC, AES-GCM, 3DES, and SHA-256 at line rate across the four GbE ports. This allows a single 1.5 GHz core to sustain 1 Gbps of IPSec traffic without software crypto overhead. The QUICC Engine handles deep packet inspection and DPI pattern matching. The PCIe x4 lane enables connection to a crypto accelerator card if higher throughput is needed.
推荐
Multi-Function Printers and Imaging Platforms
Imaging applications like multi-function printers and document scanners use the MPC8536EBVTAVLA to drive the JBIG/MPEG codec engine plus the high-speed scan-to-network pipeline. The four GbE MACs serve duplex scan-to-email, fax-over-IP, and the embedded web interface. The USB 2.0 host handles walk-up printing from USB drives, while the SDHC slot configures user-defined presets. DDR3 bandwidth keeps the raster image processor (RIP) fed without page-bottlenecks.
推荐
Telecom Control Plane and Baseband Equipment
Telecom control plane cards in LTE small cells and baseband units use the MPC8536EBVTAVLA for protocol stack termination on the F1/eCPRI interface. The 0C to 105C industrial temperature range and high MTBF qualify it for outdoor and basement deployments. The hardware SEC block secures S1AP and X2 handovers; the QUICC Engine offloads GTP-U encapsulation/de-encapsulation at line rate. PCIe lanes connect to DSP or FPGA co-processors for PHY-layer processing.
推荐
Automotive Ethernet Gateways and Infotainment
For vehicle gateways and head units, the MPC8536EBVTAVLA provides automotive Ethernet (100BASE-T1/1000BASE-T1) routing via its GbE MACs plus BroadR-Reach PHYs, with the SEC block securing CAN-to-Ethernet tunneling. The SDHC interface stores navigation maps and firmware updates, while USB 2.0 drives Apple CarPlay/Android Auto connectivity. The 0C to 105C temperature range satisfies automotive cabin-mount requirements.
推荐
推荐产品汇总
工程参考数据： MPC8536EBVTAVLA ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MPC8536EBVJAVLA | MPC8536ECVJAVLA | MPC8536EBVTAULA | MPC8536EBVTANLA | MPC8536EAVTAVLA |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 783-FCBGA (29x29 mm) | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same |
| Core Frequency | 1.5 GHz | 1.0 GHz | 1.0 GHz | 1.5 GHz | 1.5 GHz | 1.5 GHz |
| Core Architecture | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 |
| Operating Temperature | 0C to 105C | 0C to 105C | Extended temp range | 0C to 105C | 0C to 105C | 0C to 105C |
| Integrated GbE MACs | 4 | 4 | 4 | 4 | 4 | 4 |
| DDR Memory Support | DDR2/DDR3 up to 800 MT/s | DDR2/DDR3 up to 800 MT/s | DDR2/DDR3 up to 800 MT/s | DDR2/DDR3 up to 800 MT/s | DDR2/DDR3 up to 800 MT/s | DDR2/DDR3 up to 800 MT/s |
| Security Engine (SEC) | Yes | Yes | Yes | Yes | Yes | Yes |
| Lead-Free / RoHS | Yes | Yes | Yes | Yes | Yes | Yes |
关键差异点
- Highest speed grade within the MPC8536E family （对比 MPC8536EBVJAVLA)
- Integrated QUICC Engine + hardware SEC （对比 MPC8536EBVTAULA)
- Commercial temperature range rated to 105C （对比 MPC8536ECVJAVLA)
设计说明
The 783-FCBGA at 1 mm pitch requires a minimum 4-2-4 or 6-layer stack-up with 0.0762 mm (3 mil) signal traces between 0.2 mm microvias for breakout. Use via-in-pad with copper-filled and plated-over microvias per IPC-6012 Class 3 for high-yield assembly. Maintain a continuous reference plane under the BGA; voids greater than 50% of any one pad will fail PCIe or SATA Gen 2 compliance testing per the Freescale/NXP hardware design guide.
DDR3-800 interface requires matched-length fly-by topology with 50-ohm single-ended and 100-ohm differential impedance. Estimated: at 800 MT/s the address/command skew budget is +/-25 ps; add 0.5 mm length matching per byte lane. Keep DQ-DQS skew within +/-10 ps using serpentine routing and BGA-via length-matching per the Micron TN-41-04 reference design. Place the VTT termination resistor divider within 200 ps of the controller.
Estimated: at full core (1.5 GHz) processing load, the MPC8536E core draws approximately 8 to 10 W, requiring the FCBGA thermal pad to be soldered to a 4-inch by 4-inch (100 mm x 100 mm) copper pour on the top layer plus a matching bottom-layer plane for spreading. Without a heat spreader or heatsink, junction temperature can exceed 105C in still air. Place thermal vias (0.3 mm finished hole) on a 1.2 mm grid under the die to drop theta_JC from approximately 0.5 C/W to near 0.3 C/W.
The 1.1 V core rail must use a buck regulator capable of 12 A continuous load with +/-3% accuracy. Use TI TPS54620 or TPS53355 with remote sense routed to the BGA center to compensate for IR drop across the PCB. Sequence the 1.1 V core before the 1.5 V DDR3 supply and 2.5 V/3.3 V I/O rails; failure to sequence can trigger latch-up per the NXP MPC8536E datasheet hardware design guide.
Do not assume the QUICC Engine is software-compatible across speed grades - the J-suffix and T-suffix variants share the same binary firmware but different hardware errata documents must be checked. Verifying CFG_RST configuration at POR is mandatory: pulling PORESET during power sequencing restores factory defaults. Forgetting to assert the JTAG TRST line during reset disables boundary scan for production test.
合规信息
Lead-free and RoHS compliant per the FCBGA package marking in the verified datasheet specification. REACH, halogen-free, and conflict-mineral declarations should be requested from NXP Compliance directly; XAIPART has not aggregated these for this part.
