Amplifier ICs
بەرهەمەکان (3,200+)
TAS5602DCAR - 20W Stereo PWM-Input Class-D Power Stage | TI (Tape & Reel)
The Texas Instruments TAS5602DCAR is a 20 W per channel stereo digital Class-D audio amplifier power stage with PWM input, housed in a 56-pin HTSSOP (DCA) package with an exposed thermal pad. It operates from a 10 V to 26 V supply and can drive four single-ended speakers or two bridge-tied (BT) speakers from a single device. A Class-D audio amplifier is a switching power amplifier that delivers audio output by applying a constant-amplitude PWM carrier to the speaker load, so the transistor output stage conducts only when the PWM signal is active. In the device hierarchy, TAS5602DCAR belongs to the amplifier IC family, inside audio amplifiers, inside integrated circuits, inside analog power and signal-chain semiconductors. Unlike a conventional analog input amplifier, this part accepts a PWM signal directly from a digital audio processor or a Class-D modulator, eliminating an analog input stage and its associated noise and distortion. Key features include 20 W of continuous output power per channel, a wide 10 V to 26 V operating supply range, and support for both single-ended and bridge-tied speaker configurations. Because the part accepts PWM rather than an analog voltage, the noise floor is set entirely by the upstream digital source, which keeps inter-channel noise and distortion very low and makes channel matching essentially perfect. The device supports 2-channel stereo, 4-channel quad, and mono operation modes, giving a single part number flexibility for multiple speaker topologies. Internally, the TAS5602 architecture combines a half-bridge output stage with integrated feedback control, so the amplifier can be configured with or without a feedback resistor network to suit the target speaker impedance. Because output stage switching is fully synchronous and the modulator runs at a high carrier frequency, the switching losses remain low and the power stage can be mounted on standard two-layer PCB copper without a bulky external heatsink in typical 10 W per channel designs. Typical applications include consumer and industrial audio: multi-room and networked speakers, sound bars, TV and monitor speaker drivers, Bluetooth and Wi-Fi speaker systems, USB and PC audio docks, and powered speaker systems. The 56-pin HTSSOP package with exposed pad provides a large thermal copper area, which is essential for continuous 20 W per channel operation from a 24 V rail. When laying out the board, treat the exposed pad as both the thermal path and the main ground return. Use a solid ground pour with minimal inductance between the output drivers and the supply bypass capacitors, and place the input PWM traces away from the switching node to avoid coupling the carrier frequency into the audio path. This page brings together the manufacturer ordering information, a parameter-by-parameter comparison against related Texas Instruments Class-D power stages, and practical thermal and layout guidance that goes beyond the headline specifications found in the datasheet.
TAS5611APHD - 125W Stereo Class-D Amplifier | Texas Instruments
The Texas Instruments TAS5611APHD is an analog-input Class-D audio power amplifier rated for 125 W stereo output or 250 W mono output from a 16 V to 34.1 V supply. The device is packaged in a 64-pin HTQFP PHD package measuring 14 mm by 14 mm and incorporates PurePath HD closed-loop feedback technology. A Class-D audio amplifier is a switching power stage that delivers high audio output power with substantially greater efficiency than a traditional linear amplifier. The TAS5611A family combines a differential analog input, a Class-D output stage, and integrated closed-loop feedback. This places it in the audio amplifier hierarchy alongside stereo power amplifiers, speaker drivers, and power-management ICs used in home audio, automotive, and industrial systems. Key features include configurable mono or stereo operation, 125 W per channel in stereo mode, 250 W in mono mode, and an operating supply range of 16 V to 34.1 V. PurePath HD feedback is intended to improve distortion and frequency-response performance in the power stage. The device accepts an analog input and provides a differential speaker output, allowing direct integration into powered speakers and multi-channel audio systems. The PHD package is a 64-pin HTQFP with an exposed thermal pad. Its high-output topology makes thermal management and PCB copper layout critical: power-stage losses must be transferred through the package and board rather than treated as only an IC-level concern. The manufacturer product page lists the operating temperature as 0 °C to 70 °C for this orderable part. Exact feedback, modulation, efficiency, and thermal values should be confirmed against the manufacturer datasheet before a production design is released. Typical applications include powered bookshelf speakers, compact home-theater amplifiers, professional audio equipment, soundbars, and automotive-style audio modules. Stereo operation uses the device as a dual-channel 125 W amplifier, while bridged mono operation combines the channels for up to 250 W into one speaker. The wide 16 V to 34.1 V supply range suits systems using a nominal 24 V automotive or industrial bus after appropriate regulation and protection. A critical design requirement is to provide the datasheet-recommended power and ground layout, use a low-inductance speaker-output path, and connect the exposed thermal pad to an adequate copper area. The analog input and feedback network also require careful grounding to prevent channel interaction. Validate peak thermal conditions and speaker impedance at the maximum intended output power. This product guide combines the exact orderable-part characteristics, package details, application guidance, replacement considerations, and practical layout checks needed to evaluate the TAS5611APHD as a high-power Class-D audio solution.
TAS5611PHD - 125W Stereo/250W Mono Class-D | Texas Instruments
Texas Instruments TAS5611PHD is an analog-input Class-D audio power stage rated for up to 125 W stereo output or 250 W mono output, housed in a 64-pin HTQFP package with an exposed thermal pad. The device supports a 32.5 V supply and is designed to drive 4 Ω to 8 Ω speakers, combining Class-D efficiency with the low distortion traditionally associated with Class-AB amplification. A Class-D audio power stage is a switching amplifier category that uses transistor output stages to deliver high audio power efficiently. Unlike a linear Class-AB amplifier, its output transistors operate principally in switching states, reducing conduction losses. PurePath HD, the integrated closed-loop feedback technology used in the TAS5611, helps the device achieve total harmonic distortion below 0.03% while retaining the efficiency advantage of Class-D operation. The headline capabilities include analog signal input, 125 W stereo or 250 W mono output, support for 4 Ω to 8 Ω speaker loads, and operation from a single 32.5 V supply. The 64-pin HTQFP package measures 14 mm by 14 mm and incorporates an exposed pad that requires careful PCB thermal design. These characteristics make the device suitable for high-power consumer audio, home-theater amplification, powered speakers, and compact professional audio systems. The PurePath HD architecture is central to the amplifier’s performance. Integrated closed-loop feedback monitors the output waveform and corrects nonlinear distortion introduced by the power stage. In an analog-input implementation, the amplifier accepts a conventional audio signal rather than requiring a digital audio codec, allowing it to operate with preamplifiers, tone-control circuits, volume-control stages, or other line-level sources. Analog input also keeps the signal chain compatible with existing analog audio equipment. Typical uses include stereo home-theater receivers, powered bookshelf speakers, active subwoofers, compact stereo amplifiers, and single-channel high-output installations. A bridge-tied mono configuration can increase the available power into one speaker load, while the stereo configuration distributes the amplifier’s output between two channels. Appropriate speaker selection and power-supply design remain essential because actual thermal performance depends strongly on the PCB copper area, heat spreading, supply capability, and enclosure ventilation. The principal design consideration is heat management. The exposed thermal pad must be connected to a properly designed copper heat-spreading area, and the amplifier’s operating mode must be evaluated at the intended load impedance and power level. Inductor selection, speaker filtering, grounding, and high-current supply routing also influence switching noise, output stability, and EMI performance. The manufacturer’s reference layouts should be used as the starting point for a new design. This page combines the verified 125 W stereo, 250 W mono, 32.5 V, distortion, package, and application information with practical selection guidance, package considerations, and clearly qualified drop-in alternatives. It is intended to help engineers determine whether the TAS5611PHD fits a high-power analog-input Class-D design before beginning board-level implementation.
TAS5612PHD - 125W Stereo Class D Amplifier | Texas Instruments
The Texas Instruments TAS5612PHD is a PurePath HD Class D audio power amplifier rated for 125 W per channel in stereo operation and 250 W in mono operation. It accepts one-channel mono or two-channel stereo signals and is packaged in a 64-pin HTQFP measuring 14 mm by 14 mm. The device is intended for high-power audio systems requiring efficient amplification into 4 ohm to 8 ohm speaker loads. A Class D audio amplifier is a switching power amplifier whose transistor output stage operates with controlled PWM signals. Compared with a linear audio amplifier, this topology can convert amplifier input power into speaker output power more efficiently, reducing heat and allowing high output power in a compact package. The TAS5612PHD belongs to the broader hierarchy of audio amplifiers, audio power amplifiers, power management ICs, and semiconductors. The primary performance ratings are 125 W stereo output, 250 W mono output, and operation from a 16 V to 34.1 V supply range. A 10.8 V to 13.2 V range is also associated with the device in the technical listing. Its integrated closed-loop feedback technology, called PurePath HD, helps the amplifier correct output-voltage distortion through the speaker connection rather than relying only on feedback around the power stage. The device supports either one-channel mono operation or two-channel stereo operation. This flexibility makes it suitable for home-theater power stages, professional audio amplification, subwoofer amplifiers, and compact high-power speaker systems. The 64-pin HTQFP package requires a carefully designed exposed-pad thermal layout, and its power-class application makes heat dissipation a central PCB-design requirement. For robust implementation, designers should follow the manufacturer datasheet for the recommended power topology, input filtering, speaker output network, supply decoupling, and thermal land pattern. The evaluation module TAS5612/14PHD2EVM provides a practical reference for evaluating TAS5612PHD alongside TAS5614PHD and TAS5518PAG in a PurePath HD audio system. This page combines the manufacturer device ratings with practical guidance for thermal management, output-network implementation, supply decoupling, and device selection. It also distinguishes confirmed family alternatives from components that only provide related functionality but cannot be assumed to be pin-compatible replacements.
TAS5613APHD - 150W Stereo Class-D Amplifier | TI
The Texas Instruments TAS5613APHD is a 150 W stereo, 300 W mono, analog-input Class-D audio power stage with an 18 V to 38 V supply range, packaged in a 64-pin HTQFP (PHD) with exposed pad. It uses TI PurePath HD technology and integrated closed-loop feedback to drive speaker loads efficiently. The device supports one-channel mono or two-channel stereo operation, making it suitable for powered speakers, home-theater receivers, professional audio equipment, and automotive audio systems. A Class-D audio amplifier is a switching power amplifier that uses transistor output stages to deliver audio energy efficiently. In the signal path, an analog input is amplified and converted into a high-frequency switching waveform. The speaker reconstructs the audio signal through its filtering characteristics. Compared with a linear output stage, Class-D architecture can reduce heat and power loss, while the TAS5613APHD adds integrated feedback for low distortion and reliable speaker drive. Key capabilities include up to 150 W per channel into a 4-ohm stereo load, up to 300 W in mono operation, an 18 V to 38 V analog power-supply range, and integrated PurePath HD feedback. The manufacturer datasheet states that achievable output power depends on the thermal configuration of the target application. The 14 mm by 14 mm HTQFP package therefore requires careful exposed-pad heat transfer and an appropriately sized thermal design. The device is designed for analog-input audio systems and includes active enable control, integrated feedback, and protection functions associated with the TAS5613A family. Its power-stage architecture is intended to simplify design around high-power Class-D amplification. External filtering, supply decoupling, output-network selection, and thermal-interface materials remain central to achieving clean, stable operation at high output power. Typical applications include 150 W stereo active speakers, 300 W mono subwoofers, multi-zone residential audio, powered cinema speakers, and professional monitor amplifiers. Its dual-channel configuration can also support parallel or bridged arrangements where the board design and speaker impedance permit them. The relatively high supply requirement makes it more appropriate for mains-powered or automotive 24 V systems than for low-voltage portable equipment. Thermal design is the primary implementation constraint. Place the exposed pad against a thermal interface and substantial copper area, then use the manufacturer datasheet’s recommended PCB layout and reference-design power-supply components. Verify output-power capability across ambient temperature, speaker impedance, supply voltage, and enclosure temperature rather than relying on the headline power rating alone. This product summary combines the family-level power capability, package information, supply range, and application positioning with practical guidance for thermal management, board layout, sourcing, and drop-in replacement assessment. It also organizes the most relevant companion audio components and engineering trade-offs into a design-oriented reference for amplifier selection.
TAS5613PHD - 150W Stereo Class-D Power Stage | Texas Instruments
The Texas Instruments TAS5613PHD is a 150 W stereo Class-D audio power stage with integrated feedback, analog input, and 64-pin HTQFP packaging. It operates from an 18 V to 38 V power-supply range, supports a 10.8 V to 13.2 V analog input range, and supports mono or stereo output configurations. The device also provides signal bandwidth up to 80 kHz for high-definition audio content. A Class-D audio power stage is an efficient switching amplifier that converts analog audio signals into high-power drive for loudspeakers. It belongs to the amplifier IC hierarchy, specifically the audio amplifier and power-amplifier categories. Compared with linear audio amplifiers, Class-D architectures can provide high output power with lower power dissipation because the switching elements are operated near their fully-on or fully-off states. Integrated feedback helps the device regulate its power stage and supports repeatable amplifier design. The TAS5613PHD delivers up to 150 W in a stereo configuration and up to 300 W in a mono configuration. According to the manufacturer product page, distortion can be as low as 0.03% THD at 1 W into 4 ohms, while flat total harmonic distortion across frequency is positioned for natural sound reproduction. Power-supply rejection reaches 80 dB in bridge-tie-load operation without an input signal, and signal-to-noise ratio can exceed 100 dB when weighted for A. The device uses PurePath HD analog-input technology and provides click-and-pop-free startup and shutdown behavior. Its integrated-feedback architecture is intended to simplify power-stage implementation while retaining high-frequency signal capability. The manufacturer identifies pin compatibility with the TAS5630, TAS5615, and TAS5611 families, enabling designers to evaluate different power levels or feature sets while retaining a common package strategy. Typical applications include high-power stereo audio receivers, active loudspeakers, home-theater amplification, multichannel audio systems, and compact subwoofer or full-range driver stages. The 150 W stereo rating is particularly relevant to consumer and professional audio equipment where a single integrated stage can drive conventional passive loudspeakers efficiently. The 300 W mono configuration offers additional flexibility for bridged applications or higher-power single-channel systems. Thermal design remains a central implementation consideration because Class-D power stages concentrate losses in the switching devices and package. Follow the manufacturer’s recommended land pattern, component placement, thermal-pad connection, power-supply decoupling, and output-filter guidance. Account for worst-case supply voltage, channel imbalance, amplifier gain, and enclosure temperature rather than sizing the system only from nominal output power. This page organizes the manufacturer’s key technical facts, package information, family relationships, and engineering guidance for faster component evaluation. The comparison and selection sections also clarify how the pin-compatible TAS5613PHD relates to other PurePath HD power stages when power capability, channel architecture, and thermal requirements differ.
TAS5614APHD - 150W Stereo Class-D Power Stage | TI
The Texas Instruments TAS5614APHD is a digital-input Class-D audio power stage rated for 150 W stereo or 300 W mono operation, with an 18 V to 38 V power-stage supply and a 64-pin HTQFP (PHD) package. It uses PurePath HD closed-loop feedback to monitor the output during operation, combining high output power with integrated digital control and amplifier supervision. A Class-D audio power stage is a switching amplifier topology that efficiently converts a supply rail into a high-current speaker output. Unlike a linear output stage, it dissipates less energy during normal power delivery and is commonly used where efficiency, thermal performance, and compactness matter. Within the power-amplifier hierarchy, this device is a digital-input audio power stage intended to drive passive loudspeakers from a regulated power supply. The TAS5614APHD supports up to 150 W per channel in stereo or 300 W into a mono load from a 36 V supply. Its operating supply range extends from 18 V to 38 V, allowing use in 24 V and 36 V power systems. Digital input control supports programmable operation, while integrated feedback provides real-time output monitoring. The 14 mm by 14 mm exposed-pad package improves heat transfer through its bottom thermal pad. Texas Instruments describes the device as a high-performance Class-D amplifier with integrated closed-loop feedback. The digital command interface allows a system controller to configure operating behavior rather than relying only on analog gain-setting components. For thermal and acoustic design, the key considerations are output-filter selection, speaker impedance, continuous versus peak power, copper heat spreading, and the stability of the 12 V logic and 36 V power-stage supplies. Typical applications include powered speakers, sound bars, home-theater receivers, professional audio amplification, and compact multimedia systems. The stereo configuration supports two independently driven channels, while the mono configuration can provide higher output power to a single speaker or subwoofer. The integrated digital control also makes the device suitable for systems that require remote gain, status monitoring, or fault management. Use the TAS5614A reference-layout guidance and the application diagrams in the manufacturer datasheet for high-current routing, grounding, decoupling, output filtering, and exposed-pad thermal management. The 36 V power-stage rail should have low output impedance and low noise, and the recommended 12 V supply should likewise come from a low-noise, low-output-impedance regulator. This product overview combines the manufacturer power ratings, package information, supply limits, and application guidance with practical alternatives and selection criteria. It helps engineers identify whether the TAS5614APHD matches the required channel count, speaker impedance, output power, control interface, thermal envelope, and supply architecture of a new Class-D audio design.
TAS5614PHD - 150W Stereo Class D Power Stage | TI
The Texas Instruments TAS5614PHD is a 150W stereo or 300W mono Class D audio power stage using PurePath HD technology and housed in a 64-pin HTQFP package measuring 14 x 14 mm. It accepts analog audio input and uses integrated closed-loop feedback to drive 4 ohm to 8 ohm speakers from a single supply rated up to 36V. A Class D audio power stage is a switching amplifier that converts an analog audio waveform into a high-frequency PWM output, filtering it at the speaker terminals to recover the amplified audio signal. Its place in the hierarchy is audio power IC, power amplifier IC, Class D amplifier, and power-management semiconductor. Compared with a linear amplifier, the switching architecture can substantially reduce output-stage dissipation while maintaining low distortion through closed-loop feedback. The headline capabilities are 150W stereo output, 300W mono output, a Class D output stage, analog input, and PurePath HD feedback. The device can operate from an 18V to 38V supply range, while published supply figures also identify a 10.8V to 13.2V operating condition. The manufacturer positions the part for driving 4 ohm to 8 ohm stereo speakers from one 36V supply, making it relevant to powered speakers, AV receivers, compact cinema systems, and professional audio equipment. The TAS5614PHD is intended as a power-stage device rather than a complete audio system controller. Its input and digital-control functions must be integrated with a preamplifier or codec that supplies the audio signal. Closed-loop PurePath HD feedback is the central architecture feature: the amplifier monitors its output and corrects the switching stage to reduce distortion rather than relying only on open-loop drive accuracy. Because the device dissipates substantial power at high output levels, the exposed heatslug is central to the mechanical design. Texas Instruments specifies a high-performance thermal interface material between the package heatslug and the heat sink. The 14 x 14 mm HTQFP package therefore needs a defined heat-spreading and convection path to sustain the 150W stereo and 300W mono ratings. This page combines the manufacturer product information with distributor listings and a package-level comparison for design planning. Because the detailed pin-description and thermal tables reside in the manufacturer datasheet, use that document for final pin assignment, exposed-pad treatment, filter selection, and heat-sink design.
TAS5615DKD - 160W Stereo Class-D Amplifier | TI
Texas Instruments TAS5615DKD is an analog-input Class-D audio power amplifier with integrated closed-loop feedback using PurePath HD technology. It supports up to 160 W stereo output into 8-ohm speakers from a single 50 V supply, or up to 300 W mono operation, and is packaged in a 44-pin HSSOP package. According to the manufacturer product page, distortion is below 0.03% THD while retaining the efficiency associated with Class-D operation. A Class-D audio power amplifier is a switching power stage that converts an analog input waveform into a high-frequency PWM representation and reconstructs the audio signal at the speaker output. The TAS5615 family belongs to the broader class of integrated audio amplifiers, combining a power-conversion stage with feedback control in one device. Its integrated PurePath HD closed-loop feedback system is intended to improve linearity and reduce distortion compared with relying only on an external speaker feedback network. The TAS5615DKD accepts analog audio inputs and is designed for high-power stereo and mono speaker drive. Its stated 160 W stereo capability is based on operation from a 50 V supply, while the 300 W mono figure supports dedicated single-channel or bridged configurations. The supported power-supply range shown in the component listing is 25 V to 52.5 V, and a separate 10.8 V to 13.2 V range is associated with its internal auxiliary supply domain. PurePath HD technology is the principal technical differentiator of this power stage. Closed-loop feedback samples the output and corrects the switching waveform, supporting the manufacturer’s specified total harmonic distortion below 0.03%. This combination of analog input, Class-D efficiency, and feedback-based distortion control makes the device suitable for professional audio amplification, home-theater receivers, powered speakers, subwoofers, and other systems using low-impedance loudspeakers. For stereo installations, the amplifier drives left and right channels from analog inputs while operating from a high-voltage supply. A bridged mono arrangement can increase the available output into one speaker or a matched pair of speakers. The exact output power depends on supply voltage, speaker impedance, channel configuration, thermal conditions, and the load presented by the speaker network, so these conditions must be confirmed during amplifier and thermal design. The 44-pin HSSOP package requires careful PCB layout and adequate copper for heat removal. Power and ground connections should use short, wide traces with low loop area, while the manufacturer’s layout guidance should govern input routing, feedback connections, decoupling, and thermal via placement. The device is a power IC, but thermal design must use the maximum expected dissipation at the selected supply voltage and load rather than relying only on nominal output power. This product page combines the manufacturer’s core performance claims with package, interface, supply, and sourcing details, while adding application guidance and verified drop-in replacement status for engineering evaluation. Use the Request a Quote form for current commercial availability, and consult the manufacturer datasheet before finalizing the PCB, heat sink, output network, and protection scheme.
TAS5615DKDR - 160W Stereo Class-D Amplifier | TI (Tape & Reel)
Texas Instruments TAS5615DKDR is an analog-input Class-D audio power amplifier with integrated closed-loop feedback using PurePath HD technology. It supports up to 160 W stereo output into 8-ohm speakers from a single 50 V supply, or up to 300 W mono operation, and is packaged in a 44-pin HSSOP package. According to the manufacturer product page, distortion is below 0.03% THD while retaining the efficiency associated with Class-D operation. A Class-D audio power amplifier is a switching power stage that converts an analog input waveform into a high-frequency PWM representation and reconstructs the audio signal at the speaker output. The TAS5615 family belongs to the broader class of integrated audio amplifiers, combining a power-conversion stage with feedback control in one device. Its integrated PurePath HD closed-loop feedback system is intended to improve linearity and reduce distortion compared with relying only on an external speaker feedback network. The TAS5615DKDR accepts analog audio inputs and is designed for high-power stereo and mono speaker drive. Its stated 160 W stereo capability is based on operation from a 50 V supply, while the 300 W mono figure supports dedicated single-channel or bridged configurations. The supported power-supply range shown in the component listing is 25 V to 52.5 V, and a separate 10.8 V to 13.2 V range is associated with its internal auxiliary supply domain. PurePath HD technology is the principal technical differentiator of this power stage. Closed-loop feedback samples the output and corrects the switching waveform, supporting the manufacturer’s specified total harmonic distortion below 0.03%. This combination of analog input, Class-D efficiency, and feedback-based distortion control makes the device suitable for professional audio amplification, home-theater receivers, powered speakers, subwoofers, and other systems using low-impedance loudspeakers. For stereo installations, the amplifier drives left and right channels from analog inputs while operating from a high-voltage supply. A bridged mono arrangement can increase the available output into one speaker or a matched pair of speakers. The exact output power depends on supply voltage, speaker impedance, channel configuration, thermal conditions, and the load presented by the speaker network, so these conditions must be confirmed during amplifier and thermal design. The 44-pin HSSOP package requires careful PCB layout and adequate copper for heat removal. Power and ground connections should use short, wide traces with low loop area, while the manufacturer’s layout guidance should govern input routing, feedback connections, decoupling, and thermal via placement. The device is a power IC, but thermal design must use the maximum expected dissipation at the selected supply voltage and load rather than relying only on nominal output power. This product page combines the manufacturer’s core performance claims with package, interface, supply, and sourcing details, while adding application guidance and verified drop-in replacement status for engineering evaluation. Use the Request a Quote form for current commercial availability, and consult the manufacturer datasheet before finalizing the PCB, heat sink, output network, and protection scheme.
TAS5615PHD - 300W Mono Class-D Power Stage | Texas Instruments
The Texas Instruments TAS5615PHD is an analog-input Class-D audio power stage with integrated PurePath HD closed-loop feedback, capable of delivering up to 300 W mono output or 160 W stereo output into 8-ohm speakers from a single 50 V supply. It is packaged in a 64-pin HTQFP power package measuring 14 mm by 14 mm and includes an exposed thermal pad for heat dissipation. The device supports mono, stereo, and four-channel speaker configurations while maintaining total harmonic distortion below 0.03% under the conditions stated by Texas Instruments. A Class-D audio power amplifier is a switching amplifier that uses pulse-width modulation to deliver speaker power efficiently. The TAS5615PHD belongs to the Class-D amplifier, audio power IC, and power-management semiconductor hierarchy. Unlike a conventional linear Class-AB output stage, its switching architecture concentrates unwanted energy at high frequencies, reducing output-stage heat while retaining low audio distortion through the integrated closed-loop feedback system. The headline features include analog input, support for a 50 V power-stage supply, up to 160 W per channel in stereo operation, and up to 300 W in mono operation. PurePath HD feedback is intended to suppress distortion associated with output-network component variation. The device accepts conventional analog audio signals, which simplifies its use in systems that do not require a PWM audio source. Its 64-pin HTQFP package provides numerous power, feedback, ground, signal, and control connections needed for a high-power output stage. The PurePath HD architecture continuously corrects the output waveform using feedback sensed from the speaker output. This approach is intended to provide Class-AB-like fidelity while retaining the efficiency of a Class-D output stage. Texas Instruments specifies distortion below 0.03%, making the device suitable for high-fidelity amplification where audible distortion, clipping, or thermal losses would otherwise constrain the amplifier selection. Typical uses include powered speakers, home-theater amplifiers, professional audio equipment, soundbars, multichannel audio systems, and compact high-power subwoofer or surround-speaker platforms. In a stereo design, the integrated output stages drive left and right channels. In a mono design, the power capability can be consolidated for a single loudspeaker or bridged audio architecture, subject to the thermal and load limitations in the manufacturer datasheet. Careful thermal design is essential because the exposed pad must dissipate power generated by the switching output stage. Follow the manufacturer application diagrams for the power-supply topology, output inductors, feedback network, input filtering, copper area, and thermal layout. The 50 V power-stage rail should have low output impedance and low noise, and the 12 V supply should originate from a low-noise, low-output-impedance regulator. This page organizes the verified power ratings, package information, operating architecture, application fit, and engineering cautions for the TAS5615PHD. It also distinguishes the target device from related TI products so design engineers can determine whether the analog-input interface, power rating, package, and thermal requirements match the intended amplifier platform.
TAS5615PHDR - 300W Mono Class-D Power Stage | Texas Instruments (Tape & Reel)
The Texas Instruments TAS5615PHDR is an analog-input Class-D audio power stage with integrated PurePath HD closed-loop feedback, capable of delivering up to 300 W mono output or 160 W stereo output into 8-ohm speakers from a single 50 V supply. It is packaged in a 64-pin HTQFP power package measuring 14 mm by 14 mm and includes an exposed thermal pad for heat dissipation. The device supports mono, stereo, and four-channel speaker configurations while maintaining total harmonic distortion below 0.03% under the conditions stated by Texas Instruments. A Class-D audio power amplifier is a switching amplifier that uses pulse-width modulation to deliver speaker power efficiently. The TAS5615PHDR belongs to the Class-D amplifier, audio power IC, and power-management semiconductor hierarchy. Unlike a conventional linear Class-AB output stage, its switching architecture concentrates unwanted energy at high frequencies, reducing output-stage heat while retaining low audio distortion through the integrated closed-loop feedback system. The headline features include analog input, support for a 50 V power-stage supply, up to 160 W per channel in stereo operation, and up to 300 W in mono operation. PurePath HD feedback is intended to suppress distortion associated with output-network component variation. The device accepts conventional analog audio signals, which simplifies its use in systems that do not require a PWM audio source. Its 64-pin HTQFP package provides numerous power, feedback, ground, signal, and control connections needed for a high-power output stage. The PurePath HD architecture continuously corrects the output waveform using feedback sensed from the speaker output. This approach is intended to provide Class-AB-like fidelity while retaining the efficiency of a Class-D output stage. Texas Instruments specifies distortion below 0.03%, making the device suitable for high-fidelity amplification where audible distortion, clipping, or thermal losses would otherwise constrain the amplifier selection. Typical uses include powered speakers, home-theater amplifiers, professional audio equipment, soundbars, multichannel audio systems, and compact high-power subwoofer or surround-speaker platforms. In a stereo design, the integrated output stages drive left and right channels. In a mono design, the power capability can be consolidated for a single loudspeaker or bridged audio architecture, subject to the thermal and load limitations in the manufacturer datasheet. Careful thermal design is essential because the exposed pad must dissipate power generated by the switching output stage. Follow the manufacturer application diagrams for the power-supply topology, output inductors, feedback network, input filtering, copper area, and thermal layout. The 50 V power-stage rail should have low output impedance and low noise, and the 12 V supply should originate from a low-noise, low-output-impedance regulator. This page organizes the verified power ratings, package information, operating architecture, application fit, and engineering cautions for the TAS5615PHDR. It also distinguishes the target device from related TI products so design engineers can determine whether the analog-input interface, power rating, package, and thermal requirements match the intended amplifier platform.
TAS5616DKD - 300W Mono Class-D Amplifier | Texas Instruments
The Texas Instruments TAS5616DKD is a digital-input Class-D audio power amplifier with integrated PurePath HD feedback, designed for mono or stereo speaker drive. It supports 25 V to 52.5 V power-supply operation, 10.8 V to 13.2 V PWM logic supply operation, 160 W stereo output into 8-ohm loads, and up to 300 W mono output. The device is packaged in a 44-pin HSSOP power package with an exposed thermal pad. A Class-D amplifier is a switching audio power stage in which the output transistor operates in a fully switching state. Its efficiency allows substantial audio power with lower conduction loss than a conventional linear amplifier. The TAS5616DKD is a high-performance PWM-input Class-D device with integrated closed-loop feedback, providing a practical solution for powered speakers, home-theater equipment, and compact high-power audio systems. Key characteristics include a 44-pin HSSOP package, integrated closed-loop feedback, digital PWM input, support for mono or stereo operation, and a power-supply range of 25 V to 52.5 V. The device also accepts a separate 10.8 V to 13.2 V PWM supply, allowing the system designer to manage power-amplifier and logic-supply domains independently. The exposed thermal pad is central to heat removal at high output power. The PurePath HD architecture uses integrated feedback to improve distortion and output-voltage behavior in the power stage. With an 80 kHz signal-bandwidth capability described for the device family, the amplifier is intended for high-fidelity audio reproduction rather than low-frequency-only subwoofer applications. The integrated feedback simplifies output-network design compared with systems that require external speaker feedback. Typical uses include powered stereo speakers, compact home-theater amplifiers, professional audio equipment, soundbars, and high-power subwoofer amplifiers. In each case, the supply voltage, speaker impedance, thermal design, and output-filter requirements must be selected together. The 44-pin HSSOP package requires careful PCB layout and substantial thermal copper for reliable operation near its maximum output capability. The main design consideration is heat management. Estimated power dissipation in the output stage changes with supply voltage, output voltage, load impedance, and output power. Use the exposed pad with a low-thermal-resistance PCB layout, validate amplifier temperature during maximum-power operation, and select decoupling and output filtering according to the manufacturer datasheet. This product summary combines the electrical ratings, package information, application context, practical thermal guidance, and drop-in replacement considerations for engineers evaluating the TAS5616DKD in Class-D audio designs.
TAS5616DKDR - 300W Mono Class-D Amplifier | Texas Instruments (Tape & Reel)
The Texas Instruments TAS5616DKDR is a digital-input Class-D audio power amplifier with integrated PurePath HD feedback, designed for mono or stereo speaker drive. It supports 25 V to 52.5 V power-supply operation, 10.8 V to 13.2 V PWM logic supply operation, 160 W stereo output into 8-ohm loads, and up to 300 W mono output. The device is packaged in a 44-pin HSSOP power package with an exposed thermal pad. A Class-D amplifier is a switching audio power stage in which the output transistor operates in a fully switching state. Its efficiency allows substantial audio power with lower conduction loss than a conventional linear amplifier. The TAS5616DKDR is a high-performance PWM-input Class-D device with integrated closed-loop feedback, providing a practical solution for powered speakers, home-theater equipment, and compact high-power audio systems. Key characteristics include a 44-pin HSSOP package, integrated closed-loop feedback, digital PWM input, support for mono or stereo operation, and a power-supply range of 25 V to 52.5 V. The device also accepts a separate 10.8 V to 13.2 V PWM supply, allowing the system designer to manage power-amplifier and logic-supply domains independently. The exposed thermal pad is central to heat removal at high output power. The PurePath HD architecture uses integrated feedback to improve distortion and output-voltage behavior in the power stage. With an 80 kHz signal-bandwidth capability described for the device family, the amplifier is intended for high-fidelity audio reproduction rather than low-frequency-only subwoofer applications. The integrated feedback simplifies output-network design compared with systems that require external speaker feedback. Typical uses include powered stereo speakers, compact home-theater amplifiers, professional audio equipment, soundbars, and high-power subwoofer amplifiers. In each case, the supply voltage, speaker impedance, thermal design, and output-filter requirements must be selected together. The 44-pin HSSOP package requires careful PCB layout and substantial thermal copper for reliable operation near its maximum output capability. The main design consideration is heat management. Estimated power dissipation in the output stage changes with supply voltage, output voltage, load impedance, and output power. Use the exposed pad with a low-thermal-resistance PCB layout, validate amplifier temperature during maximum-power operation, and select decoupling and output filtering according to the manufacturer datasheet. This product summary combines the electrical ratings, package information, application context, practical thermal guidance, and drop-in replacement considerations for engineers evaluating the TAS5616DKDR in Class-D audio designs.
TAS5616PHD - 160W Stereo Class-D Amplifier | Texas Instruments
The Texas Instruments TAS5616PHD is a PurePath HD digital-input Class-D power-stage amplifier rated for 300 W mono operation or 160 W stereo operation. It operates from a 25 V to 52.5 V supply and is packaged in a 64-terminal, 14 mm by 14 mm HTQFP power-package with an exposed thermal pad. The device accepts a digital audio input and uses integrated closed-loop feedback to drive speaker outputs. A Class-D amplifier is a switching power amplifier that converts a digital or analog input into a pulse-width-modulated output waveform. This approach belongs to the broader power-amplifier hierarchy and can deliver high output power efficiently when the switching stage, output filter, power supply, and thermal system are designed correctly. The TAS5616PHD targets high-power audio products where low total harmonic distortion, wide signal bandwidth, and compact output-stage construction are important. Key features include a 300 W mono output rating, a 160 W stereo output rating, a 25 V to 52.5 V supply range, integrated closed-loop feedback, digital input, and signal bandwidth extending to 80 kHz. These characteristics make the amplifier suitable for powered speakers, home-theater systems, professional audio equipment, soundbars, and compact consumer-audio products requiring more output power than a conventional analog audio amplifier can provide efficiently. PurePath HD feedback is the principal technical distinction of this device. The feedback system monitors the output stage and corrects switching behavior, supporting improved audio fidelity while retaining the efficiency associated with Class-D operation. Because the device is a digital-input power stage, the system designer must also address the digital audio interface, clocking, signal integrity, switching-node layout, output filtering, and electromagnetic compatibility between the amplifier and its speakers. Typical applications include a 300 W subwoofer power stage, a 160 W stereo speaker amplifier, a powered bookshelf speaker, a home-theater receiver, and a compact high-output audio system. The 64-terminal exposed-pad package requires deliberate PCB copper and thermal management; the thermal pad is an electrical connection as well as a heat-spreading structure and must be connected according to the manufacturer layout guidance. The primary design trade-off is that a 52.5 V-class power stage requires a suitably rated supply, carefully laid-out switching nets, and an output-filter strategy appropriate for the selected speaker impedance and bandwidth. Verify DC offset, thermal performance, filter stability, and amplifier protection behavior with the intended speakers rather than assuming that nominal power ratings represent unrestricted continuous output in every enclosure.
TAS5616PHDR - 160W Stereo Class-D Amplifier | Texas Instruments (Tape & Reel)
The Texas Instruments TAS5616PHDR is a PurePath HD digital-input Class-D power-stage amplifier rated for 300 W mono operation or 160 W stereo operation. It operates from a 25 V to 52.5 V supply and is packaged in a 64-terminal, 14 mm by 14 mm HTQFP power-package with an exposed thermal pad. The device accepts a digital audio input and uses integrated closed-loop feedback to drive speaker outputs. A Class-D amplifier is a switching power amplifier that converts a digital or analog input into a pulse-width-modulated output waveform. This approach belongs to the broader power-amplifier hierarchy and can deliver high output power efficiently when the switching stage, output filter, power supply, and thermal system are designed correctly. The TAS5616PHDR targets high-power audio products where low total harmonic distortion, wide signal bandwidth, and compact output-stage construction are important. Key features include a 300 W mono output rating, a 160 W stereo output rating, a 25 V to 52.5 V supply range, integrated closed-loop feedback, digital input, and signal bandwidth extending to 80 kHz. These characteristics make the amplifier suitable for powered speakers, home-theater systems, professional audio equipment, soundbars, and compact consumer-audio products requiring more output power than a conventional analog audio amplifier can provide efficiently. PurePath HD feedback is the principal technical distinction of this device. The feedback system monitors the output stage and corrects switching behavior, supporting improved audio fidelity while retaining the efficiency associated with Class-D operation. Because the device is a digital-input power stage, the system designer must also address the digital audio interface, clocking, signal integrity, switching-node layout, output filtering, and electromagnetic compatibility between the amplifier and its speakers. Typical applications include a 300 W subwoofer power stage, a 160 W stereo speaker amplifier, a powered bookshelf speaker, a home-theater receiver, and a compact high-output audio system. The 64-terminal exposed-pad package requires deliberate PCB copper and thermal management; the thermal pad is an electrical connection as well as a heat-spreading structure and must be connected according to the manufacturer layout guidance. The primary design trade-off is that a 52.5 V-class power stage requires a suitably rated supply, carefully laid-out switching nets, and an output-filter strategy appropriate for the selected speaker impedance and bandwidth. Verify DC offset, thermal performance, filter stability, and amplifier protection behavior with the intended speakers rather than assuming that nominal power ratings represent unrestricted continuous output in every enclosure.
TAS5624ADDV - 150W Stereo Class-D Power Stage | Texas Instruments
The Texas Instruments TAS5624ADDV is a 150 W stereo, 400 W mono, PWM-input Class-D audio power-stage IC built around a thermally enhanced 44-pin HTSSOP package with an exposed pad. Its 12 V to 38 V operating range, digital PWM input architecture, and high output-power capability position it as the final amplification stage in multi-channel home-theater, powered-speaker, and professional audio systems. A Class-D audio amplifier is a switching power stage that converts a PWM command signal into a filtered bridge-tied-bias speaker output. The TAS5624ADDV belongs to the PurePath HD family of high-performance audio power stages. Its architecture combines high-efficiency output switching, integrated thermal enhancement, and a thermally enhanced package to support demanding loudspeaker drive levels in compact equipment. The primary operating ratings are a 12 V to 38 V supply range, up to 150 W stereo output, and up to 400 W mono output. The device accepts PWM input rather than analog line-level audio, allowing it to operate downstream of a digital audio processor or PWM modulator. Its 44-pin HTSSOP construction supports dense PCB layouts while providing a substantial exposed thermal pad for heat transfer. The TAS5624A family is described by Texas Instruments as a thermally enhanced version of the TAS5614A architecture, using larger MOSFETs and a revised gate-drive approach to improve efficiency and reduce losses. Because the output is a switching power stage, filter and thermal design remain as important as signal routing. The manufacturer’s reference schematics and PCB layouts provide a practical starting point for power-stage routing, bypassing, and exposed-pad thermal implementation. Typical applications include powered stereo speakers, home-theater amplifiers, professional active-monitor speakers, and compact high-output audio systems. In a multi-channel design, the PWM input can originate from a dedicated audio processor, while the power stage handles current amplification and speaker drive. Filter selection must preserve the intended audio bandwidth while suppressing the carrier waveform and associated switching harmonics. The most important layout consideration is the relationship between the exposed pad, power-ground structure, output networks, and heat-spreading copper. Place input, supply, and output-capacitor connections according to the manufacturer reference layout, minimize high-current loop area, and provide copper area around the package rather than relying only on signal-trace geometry. Thermal performance depends on the PCB copper area, via pattern, enclosure airflow, and sustained output level. This product record combines the manufacturer’s power and package ratings with practical guidance for implementation. It also distinguishes same-footprint family options from parts whose output ratings or electrical functions differ, helping engineers assess replacement suitability without confusing package similarity with guaranteed drop-in equivalence.
TAS5630BPHD - 300W Stereo Class-D Amplifier | Texas Instruments
The Texas Instruments TAS5630BPHD is an analog-input Class-D audio power amplifier rated for 300 W stereo output or 400 W mono output from a 25 V to 52.5 V supply. It uses integrated PurePath HD closed-loop feedback and is housed in a 64-pin HTQFP PHD package measuring 14 mm by 14 mm. The device supports either one mono channel or two stereo channels through a configuration determined by its external components and PCB layout. A Class-D audio amplifier is a switching power stage that efficiently converts a differential audio input into a high-current speaker output. The Class-D hierarchy belongs to audio power amplifiers, which in turn are power-management integrated circuits. Compared with a linear amplifier, a properly filtered Class-D output can deliver substantially higher power efficiency, although the switching waveform requires careful output filtering, PCB layout, and thermal management. The TAS5630BPHD combines analog input, integrated closed-loop feedback, and high-power output capability in one device. Its headline ratings are 300 W stereo output, 400 W mono output, and a 25 V to 52.5 V operating supply range. The PHD ordering option uses a 64-pin HTQFP package and is specified for a 0 °C to 70 °C ambient temperature range. Actual continuous output power depends on the power supply, speaker impedance, filter configuration, PCB copper area, heat sink, and thermal-interface material. PurePath HD feedback helps reduce distortion associated with output-network and speaker-load variations by sampling the output through the feedback network. This makes the amplifier appropriate for demanding powered-speaker systems, home-theater receivers, professional audio equipment, and compact high-power audio modules. The analog input architecture allows conventional line-level signals to be connected without requiring a separate digital-to-analog converter. Typical uses include powered stereo speakers, a bridged mono subwoofer stage, multimedia speakers, home-theater amplification, and industrial or professional audio systems. In stereo operation, the amplifier drives two channels; in mono operation, its available output power increases to 400 W. Designers must also account for the low-output-impedance, low-noise 12 V regulator recommended for the control supply in the manufacturer reference design. The main design tradeoff is thermal performance. Although the device supports 300 W stereo and 400 W mono power levels, those ratings depend on an appropriate heat sink, thermal interface, and PCB layout. Follow the TAS5630B reference-design PCB layout, keep the power-supply and output-filter paths compact, and validate junction temperature at the highest expected channel load rather than relying only on the headline wattage. This page combines the manufacturer power and package ratings with application guidance, drop-in alternatives, comparison parameters, and practical thermal and layout considerations. It is intended to help engineers determine whether the TAS5630BPHD fits a high-power analog Class-D design before committing to a 64-pin HTQFP layout.
TAS5630DKD - 300W Stereo Class-D Amplifier | Texas Instruments
The Texas Instruments TAS5630DKD is an analog-input Class-D audio power amplifier using PurePath HD integrated closed-loop feedback, with capability to deliver up to 300 W stereo or 600 W mono into 4 Ω to 8 Ω speakers. It is supplied in a 44-pin HSSOP power package with an exposed heat slug for thermal-interface installation. Achievable output power depends on the thermal configuration of the application. A Class-D amplifier is a switching audio power stage in which the output transistors operate at high frequency and deliver speaker current with high efficiency. In the amplifier hierarchy, the TAS5630 belongs to the audio amplifier IC category, then to the Class-D amplifier group and finally to the power-amplifier IC class. Its integrated closed-loop feedback is intended to reduce distortion associated with conventional open-loop Class-D output stages, while retaining the efficiency benefits of switching conversion. The main performance attributes are up to 300 W stereo output, up to 600 W mono operation, 4 Ω to 8 Ω speaker compatibility, and a 50 V power-stage supply assumption. The manufacturer documentation also shows a 10.8 V to 13.2 V signal-supply range in its application description. The 44-HSSOP package provides a large thermal connection area, but power capability depends on the heat sink, thermal interface material, copper area, board construction, and ambient conditions rather than package marking alone. PurePath HD technology is the defining architectural feature. The TI product page identifies the TAS5630 as a high-performance analog-input Class-D amplifier with integrated closed-loop feedback. Analog input allows compatibility with conventional line-level audio signals, while the integrated feedback arrangement supports a power-stage design intended for high-output applications. The manufacturer specifically recommends a low-noise, low-output-impedance 12 V regulator for the signal supply and a low-impedance, low-noise 50 V power-stage supply. Typical uses include professional power amplifiers, high-power stereo audio systems, cinema and home-theater speaker amplification, and bridged mono installations for subwoofers or full-range speakers. The device is particularly relevant where a single power amplifier must support both stereo and bridged-mono configurations, although the external supply, output-filter, speaker, and thermal designs remain application-specific. Thermal design is the principal implementation constraint. The exposed package heat slug must be coupled to a suitable heat sink through a high-performance thermal interface material, and the power stage requires stable, low-impedance supplies. Use the application diagrams in the manufacturer datasheet to select inductors, capacitors, power-supply components, and the PCB thermal interface for the intended output impedance and power level. This page organizes the manufacturer specifications, verified source links, application guidance, and replacement considerations into an engineering-focused reference. It also distinguishes confirmed package and output capabilities from parameters that require direct checking in the TI datasheet before schematic release, PCB construction, or production procurement.
TAS5630DKDR - 300W Stereo Class-D Amplifier | Texas Instruments (Tape & Reel)
The Texas Instruments TAS5630DKDR is an analog-input Class-D audio power amplifier using PurePath HD integrated closed-loop feedback, with capability to deliver up to 300 W stereo or 600 W mono into 4 Ω to 8 Ω speakers. It is supplied in a 44-pin HSSOP power package with an exposed heat slug for thermal-interface installation. Achievable output power depends on the thermal configuration of the application. A Class-D amplifier is a switching audio power stage in which the output transistors operate at high frequency and deliver speaker current with high efficiency. In the amplifier hierarchy, the TAS5630 belongs to the audio amplifier IC category, then to the Class-D amplifier group and finally to the power-amplifier IC class. Its integrated closed-loop feedback is intended to reduce distortion associated with conventional open-loop Class-D output stages, while retaining the efficiency benefits of switching conversion. The main performance attributes are up to 300 W stereo output, up to 600 W mono operation, 4 Ω to 8 Ω speaker compatibility, and a 50 V power-stage supply assumption. The manufacturer documentation also shows a 10.8 V to 13.2 V signal-supply range in its application description. The 44-HSSOP package provides a large thermal connection area, but power capability depends on the heat sink, thermal interface material, copper area, board construction, and ambient conditions rather than package marking alone. PurePath HD technology is the defining architectural feature. The TI product page identifies the TAS5630 as a high-performance analog-input Class-D amplifier with integrated closed-loop feedback. Analog input allows compatibility with conventional line-level audio signals, while the integrated feedback arrangement supports a power-stage design intended for high-output applications. The manufacturer specifically recommends a low-noise, low-output-impedance 12 V regulator for the signal supply and a low-impedance, low-noise 50 V power-stage supply. Typical uses include professional power amplifiers, high-power stereo audio systems, cinema and home-theater speaker amplification, and bridged mono installations for subwoofers or full-range speakers. The device is particularly relevant where a single power amplifier must support both stereo and bridged-mono configurations, although the external supply, output-filter, speaker, and thermal designs remain application-specific. Thermal design is the principal implementation constraint. The exposed package heat slug must be coupled to a suitable heat sink through a high-performance thermal interface material, and the power stage requires stable, low-impedance supplies. Use the application diagrams in the manufacturer datasheet to select inductors, capacitors, power-supply components, and the PCB thermal interface for the intended output impedance and power level. This page organizes the manufacturer specifications, verified source links, application guidance, and replacement considerations into an engineering-focused reference. It also distinguishes confirmed package and output capabilities from parameters that require direct checking in the TI datasheet before schematic release, PCB construction, or production procurement.
TAS5630PHD - 300W Stereo Class-D Power Stage | Texas Instruments
Texas Instruments TAS5630PHD is an analog-input Class-D audio power stage with integrated closed-loop feedback, rated for up to 300 W stereo output from a single 50 V supply in a 64-pin HTQFP package. Depending on the thermal configuration, the device can also support a 600 W mono output configuration. A Class-D audio power stage is a semiconductor amplifier category that converts a PWM switching output into a filtered analog speaker signal. The TAS5630 belongs to the Class-D amplifier, audio power amplifier, and power management IC hierarchies. Its PurePath HD architecture integrates closed-loop feedback, linking the power-stage output to the analog input and reducing sensitivity to load-dependent nonlinear distortion. The principal characteristics are 300 W maximum stereo output power, support for 4 Ω to 8 Ω speaker loads, and operation from a single 50 V supply. The device accepts analog audio input and can be configured for mono or stereo operation. These attributes suit high-power audio systems where efficiency, low heat loss, and accurate speaker-current feedback are important. The integrated feedback architecture distinguishes the TAS5630 from basic open-loop Class-D solutions. It monitors output behavior through the feedback network, allowing the amplifier to correct nonlinear output distortion. Because achievable power depends strongly on the PCB, power-supply design, thermal interface material, and heat-sink configuration, a nominal 300 W rating should not be treated as a guaranteed output level in an arbitrary enclosure. Typical applications include powered loudspeakers, active PA cabinets, professional audio consoles, home-theater power amplifiers, subwoofer amplifiers, and compact high-power stereo receivers. The 50 V supply requirement places the device in the high-voltage class-D power-stage category, requiring careful component spacing, a substantial thermal interface, and robust high-voltage layout practices. Designers should follow the manufacturer datasheet reference layout for the exposed heat slug, power stages, output network, and analog input routing. The package must be coupled to an appropriately sized heat sink through high-performance thermal interface material. Power-supply and output-network components also require voltage, current, pulse-energy, and thermal ratings suitable for Class-D operation. This product page combines the manufacturer power-stage capabilities, exact package information, thermal guidance, sourcing details, and replacement analysis. It also identifies where a true same-footprint replacement cannot be confirmed, preventing a merely similar amplifier from being presented as a drop-in substitute.
TAS5630PHDR - 300W Stereo Class-D Power Stage | Texas Instruments (Tape & Reel)
Texas Instruments TAS5630PHDR is an analog-input Class-D audio power stage with integrated closed-loop feedback, rated for up to 300 W stereo output from a single 50 V supply in a 64-pin HTQFP package. Depending on the thermal configuration, the device can also support a 600 W mono output configuration. A Class-D audio power stage is a semiconductor amplifier category that converts a PWM switching output into a filtered analog speaker signal. The TAS5630 belongs to the Class-D amplifier, audio power amplifier, and power management IC hierarchies. Its PurePath HD architecture integrates closed-loop feedback, linking the power-stage output to the analog input and reducing sensitivity to load-dependent nonlinear distortion. The principal characteristics are 300 W maximum stereo output power, support for 4 Ω to 8 Ω speaker loads, and operation from a single 50 V supply. The device accepts analog audio input and can be configured for mono or stereo operation. These attributes suit high-power audio systems where efficiency, low heat loss, and accurate speaker-current feedback are important. The integrated feedback architecture distinguishes the TAS5630 from basic open-loop Class-D solutions. It monitors output behavior through the feedback network, allowing the amplifier to correct nonlinear output distortion. Because achievable power depends strongly on the PCB, power-supply design, thermal interface material, and heat-sink configuration, a nominal 300 W rating should not be treated as a guaranteed output level in an arbitrary enclosure. Typical applications include powered loudspeakers, active PA cabinets, professional audio consoles, home-theater power amplifiers, subwoofer amplifiers, and compact high-power stereo receivers. The 50 V supply requirement places the device in the high-voltage class-D power-stage category, requiring careful component spacing, a substantial thermal interface, and robust high-voltage layout practices. Designers should follow the manufacturer datasheet reference layout for the exposed heat slug, power stages, output network, and analog input routing. The package must be coupled to an appropriately sized heat sink through high-performance thermal interface material. Power-supply and output-network components also require voltage, current, pulse-energy, and thermal ratings suitable for Class-D operation. This product page combines the manufacturer power-stage capabilities, exact package information, thermal guidance, sourcing details, and replacement analysis. It also identifies where a true same-footprint replacement cannot be confirmed, preventing a merely similar amplifier from being presented as a drop-in substitute.
TAS5631BDKD - 300W Stereo Class-D Power Stage | TI
The Texas Instruments TAS5631BDKD is a PWM-input Class-D audio power amplifier designed for a 300 W stereo output or a 400 W mono output from a single 50 V supply. It uses PurePath HD integrated closed-loop feedback and is packaged in a 44-pin HSSOP power package identified by the DKD ordering code. The device also supports 25 V to 52.5 V supply operation. A Class-D audio amplifier is a switching power amplifier that converts a PWM input into a high-frequency, high-current bridge output capable of driving loudspeakers efficiently. The Class-D hierarchy includes audio amplifiers, power amplifiers, amplifiers, and integrated circuits. Compared with a conventional linear amplifier, a Class-D stage generally shifts more of its output power into the speaker rather than dissipating it as heat inside the output devices. The TAS5631B family combines a PWM input interface with integrated closed-loop speaker feedback. Texas Instruments describes signal bandwidth up to 80 kHz and distortion below 0.03% as characteristic benefits of PurePath HD operation. The DKD package includes a two-level thermal-protection system: an active-low over-temperature warning asserts when junction temperature exceeds 125°C typically, followed by shutdown when junction temperature exceeds 155°C typically. The integrated feedback architecture continuously corrects output voltage error at the speaker, reducing the effect of speaker impedance variation and improving distortion performance. This makes the device suitable for high-power audio systems in which predictable bass response, low distortion, and stable operation across different speaker loads are important. The amplifier accepts PWM audio, so the upstream signal chain must generate a suitable PWM waveform. Typical uses include powered speakers, home-theater and professional audio equipment, multimedia enclosures, subwoofer systems, and compact high-output audio amplifiers. Mono operation can provide up to 400 W from the combined bridge outputs, while stereo operation can provide up to 300 W. The high supply voltage and substantial output capability require careful power-stage layout, thermal management, filtering, and speaker protection. Designers should follow the pin-description table and recommended layout in the manufacturer datasheet when assigning PCB tracks. The power device needs a low-impedance supply network, output inductors selected for the switching current, and an output-filter network designed for the intended speaker impedance. Thermal performance should be evaluated across maximum ambient temperature and worst-case music or sine-wave loading rather than from nominal output power alone. This page combines the manufacturer electrical and thermal ratings with application guidance, replacement analysis, and practical PCB considerations. Those engineering details help distinguish a genuine pin-compatible substitution from a merely similar Class-D amplifier and make the TAS5631BDKD easier to evaluate for professional, consumer, and industrial audio designs.
TAS5631DKD - 300W Stereo Class D Power Stage | Texas Instruments
The Texas Instruments TAS5631DKD is a PWM-input Class D audio power amplifier built on PurePath HD technology with integrated closed-loop feedback, capable of delivering 300 W per channel in stereo into 4- to 8-ohm speakers from a single 50 V supply, or 600 W in mono, in a 44-pin HTSSOP (DKD) package. The power stage accepts a 3.3 V-compatible PWM input rather than an analog signal, and operates from a 25 V to 52.5 V supply range with a 10.8 V to 13.2 V control/PWM supply domain. A Class D audio power amplifier is a switching power stage in which the output transistors are driven fully on and fully off, so the device dissipates far less energy than a linear (Class AB) amplifier at the same output level. Class D stages are the default choice for high-power consumer and professional audio: they combine high efficiency with high current capability into low-impedance loads. The PurePath HD family sits one level above ordinary Class D, adding a self-contained feedback loop inside the power stage so that distortion can be held below 0.03% without an external analog feedback network. Key features include 300 W stereo and 600 W mono output capability, integrated closed-loop feedback, PWM input with no analog input pin, an efficiency of roughly 90% at full power, integrated undervoltage and overcurrent protection, and an exposed thermal pad on the HTSSOP-44 package for direct coupling to the PCB copper. The device is intended to be paired with a PWM processor such as the TAS5086 to form a complete chipset. Technically the TAS5631 is a self-contained power stage: four bridge-tied output channels drive the speaker outputs, and the on-die feedback network senses the output voltage and corrects the drive so that the effective loop gain stays high even with long speaker cable runs and inverting or non-inverting configurations. Because the feedback is internal, the design work shifts from analog loop compensation to digital PWM generation, timing, and thermal management of the board. Typical applications include multi-channel home theater and AV receivers, active soundbars and wireless loudspeakers, powered subwoofers, smart speakers with cloud audio playback, professional powered speakers and stage-monitor amplifiers, and automotive head-unit or amplifier sub-systems. The dominant design consideration is thermal. At 300 W per channel into a 4-ohm load, the output stage dissipates a substantial fraction of the DC input power, so the exposed thermal pad must be soldered with a proper thermal via array and tied to a large copper pour, otherwise output power must be derated. Follow the recommended PCB layout, filter, and thermal via guidelines in the manufacturer datasheet when laying out the power stage. This page combines the manufacturer power-stage specifications with practical thermal, layout, and signal-chain guidance, drop-in replacement options in the same 44-pin HTSSOP footprint, and application notes that go beyond a parameter table.