Amplifier ICs
بەرهەمەکان (3,200+)
TAS5152DKDR - 125W Stereo Class D Power Stage | Texas Instruments (Tape & Reel)
The Texas Instruments TAS5152DKDR is an integrated stereo Class D digital amplifier power stage rated for 125 W per channel into a 4-ohm loudspeaker at 10% THD+N. The device operates from a 10.8 V to 13.2 V supply and is packaged in a 36-pin HSSOP. It is intended for high-power, high-efficiency stereo audio systems where a compact power stage and integrated protection are important. A Class D power stage is a switching amplifier category that uses pulse-width-modulated drive signals to transfer energy to a loudspeaker. Compared with a conventional linear audio amplifier, the Class D architecture can achieve higher conversion efficiency while reducing the amount of heat that must be removed during operation. The TAS5152DKDR belongs to the broader hierarchy of audio amplifiers, power amplifiers, power-management semiconductors, and integrated circuits. The integrated design includes gate drivers, four matched and electrically isolated enhancement-mode N-channel power DMOS transistors, and protection and fault-reporting circuitry. Its 125 W stereo output capability suits powered speakers, home-theater amplification, professional audio, and other high-output audio designs. Operation from a 10.8 V to 13.2 V supply supports conventional 12 V power-system architectures, while the listed 0 V to 37 V operating-voltage range provides additional design context. The TAS5152 is described by Texas Instruments as a third-generation, high-performance integrated stereo digital amplifier power stage with an improved protection system. Combining the output transistors and their drivers within the power-stage package reduces the number of discrete power devices required around the amplifier. The four electrically isolated DMOS devices support the full-bridge structure used by each Class D output channel. Typical applications include 125 W stereo speaker amplification, powered loudspeakers, home-theater receiver output stages, multichannel audio systems, and compact consumer or professional audio products. System designers should select the power supply, output filter, speaker load, PCB copper, and thermal solution together because output power alone does not establish safe operating conditions. For PCB implementation, follow the manufacturer pin-description table, exposed-pad connection guidance, recommended output-filter layout, and thermal design recommendations. A 12 V-class supply is the intended operating environment, and the design must preserve adequate headroom, signal integrity, output filtering, and heat-spreading paths to sustain the advertised 125 W result. This page combines the verified device specifications, application guidance, package information, and a parameter-level engineering comparison that helps engineers evaluate the TAS5152DKDR for high-power stereo amplifier designs.
TAS5162DDV - 210W Stereo Class-D Amplifier | Texas Instruments
Texas Instruments TAS5162DDV is a two-channel Class-D digital audio power amplifier rated for 210 W per channel into a 6-ohm bridge-tied load at 10% total harmonic distortion. It accepts a 0 V to 52.5 V amplifier supply and 10.8 V to 13.2 V digital supply, uses a PWM input interface, and is packaged in a 44-pin HTSSOP with an exposed thermal pad for thermal management. A Class-D audio amplifier is a switching power amplifier that uses pulse-width modulation to represent an analog audio waveform. It belongs to the broader power-amplifier hierarchy and converts digital or PWM control signals into high-current bridge-tied speaker outputs. Compared with a linear amplifier, a properly implemented Class-D stage can deliver high output power with lower power dissipation, making it suitable for home theater, multichannel audio, powered speakers, and compact high-performance sound systems. The TAS5162DDV combines a 160 W stereo configuration with a 300 W mono capability in one integrated device. Each channel can deliver up to 210 W into 6 ohms at 10% THD, while the product page identifies improved protection, low integrated output noise, low THD+N without clipping, and low idle-power dissipation. Internal pull-up resistors on the shutdown and overtemperature-warning outputs can connect those signals to 3.3 V; external pull-ups support 5 V logic levels. As a digital power stage, the device combines PWM command processing with integrated output-driver circuitry and an exposed-pad thermal interface. The 44-pin HTSSOP package provides the electrical connections required for PWM audio input, clocking, control, fault signaling, power rails, ground, and differential speaker outputs. Because output energy is dissipated in the power stage, the exposed thermal pad and PCB copper area are central to maintaining reliable operation at high continuous output power. Typical uses include powered stereo speakers, home-theater amplifiers, multimedia speaker systems, active subwoofers, and high-output consumer audio equipment. The TAS5162 can also be configured for mono operation when greater output power is required. System designers should match the speaker impedance, supply capability, switching layout, and thermal design to the intended channel configuration. For PCB implementation, place input and power decoupling close to the relevant device pins, connect the exposed pad to a properly sized thermal plane, and keep high-current speaker outputs away from sensitive audio inputs. The manufacturer datasheet's pin-description table and typical application circuit should govern net assignment, output-filter design, and thermal-pad connection. This page organizes the TAS5162DDV's principal electrical ratings, protection features, application guidance, package information, and engineering trade-offs. It also highlights where pin-compatible substitutions require additional qualification rather than assuming that similar audio amplifiers are automatic board-level replacements.
TAS5162DKD 2x210W Stereo Class-D Power Stage | Texas Instruments
The Texas Instruments TAS5162DKD is a two-channel stereo digital Class-D audio amplifier power stage capable of delivering up to 210 W per channel into a 6 ohm bridge-tied load at 10% THD+N. It accepts a 0 V to 52.5 V supply, supports PWM input, and is packaged in a 36-pin HSSOP with an exposed pad. A Class-D audio power stage is a switching amplifier topology that efficiently converts PWM signals into high-current audio outputs. Compared with a linear amplifier, the Class-D architecture places the active device in the saturation and cutoff regions, reducing conduction dissipation and supporting high output power in a compact package. The TAS5162 integrates the stereo output stage, protection functions, and digital control interfaces required by powered speakers and multi-channel audio systems. Key capabilities include 210 W per channel into a 6 ohm bridge-tied load at 10% THD+N, operation across a 0 V to 52.5 V supply range, and an improved protection system. The device is suitable for professional audio, consumer audio, home-theater equipment, powered speakers, and compact subwoofer systems. Its integrated digital power-stage architecture simplifies the output path while retaining flexible signal-control and fault-reporting functions. The TAS5162 accepts a PWM input signal and drives each output as a bridge-tied load, eliminating the need for output coupling capacitors when the specified load arrangement is used. Its integrated protection system is intended to improve reliability under normal overload and fault conditions. The exposed thermal pad must be connected to a suitable thermal and ground plane so heat can leave the package efficiently during high-power operation. Typical applications include 210 W stereo speaker amplifiers, bridged mono installations, powered bookshelf and floor-standing speakers, home-theater receivers, professional powered speakers, and subwoofer amplifiers. The 52.5 V maximum supply supports high rail voltage, but the power stage still requires careful thermal design, low-impedance PCB routing, suitable output filtering, and protection against transient overvoltage. The most important design consideration is power delivery at low impedance. Output-current capability, copper width, connector sizing, heat spreading, and the thermal resistance of the exposed pad all influence whether the amplifier can sustain its rated output continuously. Use the manufacturer power-stage application guidance and thermal data when selecting the power-supply capability, output filter, copper area, and enclosure ventilation. This product page consolidates the key TAS5162DKD specifications, package information, application guidance, sourcing path, and replacement assessment into one engineering-focused reference. It also identifies where additional datasheet data, pin-level details, and qualified alternatives are required before a board-level design is released.
TAS5162DKDR 2x210W Stereo Class-D Power Stage | Texas Instruments (Tape & Reel)
The Texas Instruments TAS5162DKDR is a two-channel stereo digital Class-D audio amplifier power stage capable of delivering up to 210 W per channel into a 6 ohm bridge-tied load at 10% THD+N. It accepts a 0 V to 52.5 V supply, supports PWM input, and is packaged in a 36-pin HSSOP with an exposed pad. A Class-D audio power stage is a switching amplifier topology that efficiently converts PWM signals into high-current audio outputs. Compared with a linear amplifier, the Class-D architecture places the active device in the saturation and cutoff regions, reducing conduction dissipation and supporting high output power in a compact package. The TAS5162 integrates the stereo output stage, protection functions, and digital control interfaces required by powered speakers and multi-channel audio systems. Key capabilities include 210 W per channel into a 6 ohm bridge-tied load at 10% THD+N, operation across a 0 V to 52.5 V supply range, and an improved protection system. The device is suitable for professional audio, consumer audio, home-theater equipment, powered speakers, and compact subwoofer systems. Its integrated digital power-stage architecture simplifies the output path while retaining flexible signal-control and fault-reporting functions. The TAS5162 accepts a PWM input signal and drives each output as a bridge-tied load, eliminating the need for output coupling capacitors when the specified load arrangement is used. Its integrated protection system is intended to improve reliability under normal overload and fault conditions. The exposed thermal pad must be connected to a suitable thermal and ground plane so heat can leave the package efficiently during high-power operation. Typical applications include 210 W stereo speaker amplifiers, bridged mono installations, powered bookshelf and floor-standing speakers, home-theater receivers, professional powered speakers, and subwoofer amplifiers. The 52.5 V maximum supply supports high rail voltage, but the power stage still requires careful thermal design, low-impedance PCB routing, suitable output filtering, and protection against transient overvoltage. The most important design consideration is power delivery at low impedance. Output-current capability, copper width, connector sizing, heat spreading, and the thermal resistance of the exposed pad all influence whether the amplifier can sustain its rated output continuously. Use the manufacturer power-stage application guidance and thermal data when selecting the power-supply capability, output filter, copper area, and enclosure ventilation. This product page consolidates the key TAS5162DKDR specifications, package information, application guidance, sourcing path, and replacement assessment into one engineering-focused reference. It also identifies where additional datasheet data, pin-level details, and qualified alternatives are required before a board-level design is released.
TAS5176DDW - 6-Ch 100W Class-D Stage | Texas Instruments
Texas Instruments TAS5176DDW is a six-channel, 100-W digital-amplifier power stage with PWM input, designed for 5.1-channel audio systems and configured for a 0-V to 34-V supply in a 44-pin HTSSOP package. Its six integrated output channels support multichannel Class-D amplification while the 10.8-V to 13.2-V PWM operating range provides a defined supply window for the power stage. A Class-D amplifier is a switching audio power amplifier whose output stage operates in a PWM state rather than continuously conducting a linear signal. This architecture belongs to the amplifier IC category and reduces the power dissipated by the output devices compared with a linear amplifier of comparable output capability. The TAS5176 integrates six digital power channels into one package, making it suitable for home-theater receivers, active speakers, soundbars, and multichannel automotive audio systems. The primary headline specifications are six output channels, up to 100 W of power capability, and a 0-V to 34-V supply range. The device accepts PWM signals directly, allowing it to work with a digital audio processor or PWM-generating audio engine. Its HTSSOP package contains 44 pins and provides a high-channel-count solution without requiring six separate power packages. The power stage is also suitable for subwoofer use when individual channels are configured appropriately. Class-D amplification places strict demands on power-supply layout, switching-node control, and thermal management. The supply and ground connections must provide low-impedance paths for high switching currents, while the exposed thermal pad and PCB copper must remove heat effectively. Incorrect output-filter or speaker-load design can increase distortion and reduce protection margin, so the manufacturer datasheet configuration should govern component selection and board implementation. Typical applications include 5.1-channel home theater amplification, active multiway speakers, powered subwoofers, compact multimedia systems, and automotive entertainment systems. An external digital audio processor can generate the PWM inputs, while the TAS5176 supplies the high-current channel drive. The six-channel arrangement also allows systems to combine several channels for higher-power BTL operation when the application and thermal design permit it. The principal design trade-off is the need for careful high-current layout and heat removal. Compared with a linear output stage, Class-D efficiency can reduce waste heat, but a 44-pin HTSSOP power package still requires careful attention to copper area, via arrays, thermal vias, and output filtering. Verify speaker impedance, supply capability, channel configuration, and maximum dissipated power before releasing a production layout. This page consolidates the exact orderable-device specifications, package information, application guidance, comparison fields, and engineering checks needed to evaluate TAS5176DDW. It also distinguishes confirmed technical facts from parameters that require confirmation in the full manufacturer datasheet before layout or production decisions.
TAS5176DDWR - 6-Ch 100W Class-D Stage | Texas Instruments (Tape & Reel)
Texas Instruments TAS5176DDWR is a six-channel, 100-W digital-amplifier power stage with PWM input, designed for 5.1-channel audio systems and configured for a 0-V to 34-V supply in a 44-pin HTSSOP package. Its six integrated output channels support multichannel Class-D amplification while the 10.8-V to 13.2-V PWM operating range provides a defined supply window for the power stage. A Class-D amplifier is a switching audio power amplifier whose output stage operates in a PWM state rather than continuously conducting a linear signal. This architecture belongs to the amplifier IC category and reduces the power dissipated by the output devices compared with a linear amplifier of comparable output capability. The TAS5176 integrates six digital power channels into one package, making it suitable for home-theater receivers, active speakers, soundbars, and multichannel automotive audio systems. The primary headline specifications are six output channels, up to 100 W of power capability, and a 0-V to 34-V supply range. The device accepts PWM signals directly, allowing it to work with a digital audio processor or PWM-generating audio engine. Its HTSSOP package contains 44 pins and provides a high-channel-count solution without requiring six separate power packages. The power stage is also suitable for subwoofer use when individual channels are configured appropriately. Class-D amplification places strict demands on power-supply layout, switching-node control, and thermal management. The supply and ground connections must provide low-impedance paths for high switching currents, while the exposed thermal pad and PCB copper must remove heat effectively. Incorrect output-filter or speaker-load design can increase distortion and reduce protection margin, so the manufacturer datasheet configuration should govern component selection and board implementation. Typical applications include 5.1-channel home theater amplification, active multiway speakers, powered subwoofers, compact multimedia systems, and automotive entertainment systems. An external digital audio processor can generate the PWM inputs, while the TAS5176 supplies the high-current channel drive. The six-channel arrangement also allows systems to combine several channels for higher-power BTL operation when the application and thermal design permit it. The principal design trade-off is the need for careful high-current layout and heat removal. Compared with a linear output stage, Class-D efficiency can reduce waste heat, but a 44-pin HTSSOP power package still requires careful attention to copper area, via arrays, thermal vias, and output filtering. Verify speaker impedance, supply capability, channel configuration, and maximum dissipated power before releasing a production layout. This page consolidates the exact orderable-device specifications, package information, application guidance, comparison fields, and engineering checks needed to evaluate TAS5176DDWR. It also distinguishes confirmed technical facts from parameters that require confirmation in the full manufacturer datasheet before layout or production decisions.
TAS5182DCA - 100W Stereo Class-D Controller | Texas Instruments
Texas Instruments TAS5182DCA is a 100 W stereo digital amplifier power-stage controller with PWM input, Class-D output, and support for up to 34 V supply voltage. The device is packaged in a 56-pin HTSSOP and is specified for an ambient temperature range of 0°C to 70°C. It is designed to control external power stages for stereo audio systems. A Class-D audio power-stage controller is a semiconductor that processes a digital audio input and generates PWM drive signals for external H-bridge transistors. Unlike a conventional analog-output audio amplifier, the controller leaves power amplification to external MOSFETs, allowing output capability to scale with the selected power stage. It belongs to the digital audio amplifier and power-management IC hierarchy. The TAS5182DCA supports stereo operation at up to 2 × 100 W RMS into a 6 Ω bridge-tied load when paired with an appropriate external power stage. Its typical total harmonic distortion plus noise is below 0.15% under the conditions identified in the manufacturer documentation. PWM input and a 0 V to 34 V supply range suit higher-power consumer and professional audio architectures. Because TAS5182DCA is a controller rather than a self-contained power amplifier, its realized output power depends on external transistors, gate-drive implementation, supply capability, layout, thermal management, and speaker impedance. The IC controls the digital audio path while the external power devices carry the loudspeaker current. This division improves flexibility compared with integrating the output transistors into the controller package. Typical uses include stereo loudspeaker systems, powered speakers, home-theater receivers, professional audio racks, and compact consumer audio products. The 56-HTSSOP package supports high-density PCB layouts, while the exposed thermal pad provides a thermal connection to the board copper. The 0°C to 70°C rating targets commercial ambient environments rather than extended industrial or automotive temperature ranges. Careful power-stage layout is essential because switching currents and gate-drive timing directly affect distortion, thermal performance, and EMI. Keep high-current power loops compact, provide local supply decoupling, use low-inductance gate-drive paths, and connect the thermal pad to an appropriately sized copper area. Select the external MOSFETs and output filter against the intended load and switching requirements. This product record combines the controller’s principal operating characteristics with application guidance, verified package information, and drop-in replacement analysis. It also distinguishes the IC’s fixed control function from the variable output power contributed by the external transistor stage, helping engineers evaluate the complete amplifier rather than relying on the nominal controller rating alone.
TAS5182IDCA - 100W Stereo Class-D Audio Controller
The Texas Instruments TAS5182IDCA is a stereo digital amplifier power-stage controller rated for 2 × 100 W RMS output at 6 V in bridge-tied-load (BTL) configurations. The device provides two-channel Class-D control, supports external discrete MOSFET output stages, and is packaged in a 56-pin HTSSOP. Its typical total harmonic distortion plus noise is below 0.15% at 1 kHz, making it suitable for high-power home-theater and powered-subwoofer systems. A digital amplifier power-stage controller is an integrated circuit that interprets an audio input and generates gate-drive signals for external switching MOSFETs. Unlike a conventional analog audio power amplifier, the TAS5182IDCA places the high-voltage and high-current switching function in discrete transistors. This separates signal processing from power conversion, allowing the external MOSFET stage to determine much of the amplifier's voltage, current, thermal, and output-power capability. The controller therefore belongs to the Class-D amplifier, digital audio amplifier, power-management IC, and semiconductor hierarchy. The 2 × 100 W capability at 6 V describes controller-supported BTL operation rather than the output of an integrated monolithic power stage. Engineers must select suitable N-channel power MOSFETs, a power-supply arrangement, an output filter, and a thermal design that match the target impedance and enclosure. The low typical distortion figure makes the controller appropriate for music reproduction systems where audible waveform deviation should remain low across the audio band. The TAS5182 architecture is intended to work with discrete bridge-tied-load output stages. In each half-bridge, the controller drives the gates of the high-side and low-side MOSFETs with complementary signals. External LC output filtering converts the switched full-bridge waveform into a filtered analog output capable of driving a loudspeaker through a BTL network. Correct gate voltage, dead time, switching speed, and layout continuity are therefore essential to the controller's real-world performance. Typical uses include home-theater amplifiers, powered subwoofers, active loudspeakers, compact stereo systems, and other high-power Class-D audio products. The controller can also serve multi-channel systems when each stereo pair is assigned to separate channels. Compared with a monolithic amplifier, the discrete-MOSFET approach offers greater freedom in output-device selection, thermal partitioning, and power scaling, but it also increases design complexity and EMI sensitivity. PCB implementation requires short gate-drive loops, careful high-current return paths, a continuous output-filter ground reference, and separation between sensitive input and switching nodes. Place input, supply, and compensation components close to their associated pins. Use thermal vias beneath exposed-pad structures where applicable and verify the selected MOSFETs, inductor, and capacitor ratings against the intended 6 V BTL operating point. EMI filtering must be evaluated together with the switching layout rather than added only after enclosure testing. This product page combines the controller's verified power and distortion ratings with package information, application guidance, drop-in family comparisons, and practical PCB design notes. It is intended to accelerate engineering selection while making the system-level responsibilities of an external-MOSFET Class-D output stage explicit.
TAS5186ADDV - 210W 6-Channel Class-D Amplifier | TI
The Texas Instruments TAS5186ADDV is a 210-W, six-channel digital power-stage Class-D audio amplifier with a 0-V to 34-V supply range, PWM input architecture, and a 44-pin HTSSOP (DDV) package. The device is designed for multichannel home-theater and powered-speaker systems where one amplifier IC can address a 5.1-channel audio signal chain. A Class-D digital power stage is an audio amplifier that uses pulse-width modulation to drive a switching output stage. Unlike a conventional linear audio amplifier, a Class-D stage can convert more of its input power into output power, reducing the amount of heat that must be removed from the amplifier assembly. The TAS5186A family integrates six output channels for compact multichannel audio systems. The TAS5186ADDV supports up to 210 W of total amplifier power, is characterized as a six-channel 30-W device, and can drive a 3-ohm load. Texas Instruments describes the power stage as capable of driving a single-ended subwoofer above 60 W at 10% THD+N. Its specified total harmonic distortion plus noise is 0.07%, making it suitable for consumer audio equipment where channel matching and low crossover distortion are important. The device accepts PWM control signals, allowing it to operate with a compatible digital audio modulator such as the TAS5086. This architecture separates audio decoding and modulation from power amplification. It also means the selected modulator must support the signal format, switching frequency, channel count, and control requirements expected by the TAS5186A family. Typical applications include 5.1-channel home-theater amplifiers, powered subwoofers, multichannel active speakers, and compact consumer audio receivers. Its 44-pin HTSSOP package supports surface-mount assembly, while the stated 0°C to 70°C operating range targets commercial indoor environments. Heat management remains important because sustained multichannel output can raise junction and PCB temperatures. For a robust design, follow the manufacturer datasheet when assigning the power, ground, PWM input, and thermal-pad connections. Place input and power-ground connections to minimize switching-current loops, use the recommended decoupling arrangement, and provide sufficient copper area under the exposed pad. Verify thermal performance across the highest expected channel load rather than relying only on nominal output power. This product page combines manufacturer specifications, application guidance, practical thermal and layout considerations, and directly documented family alternatives for engineers evaluating the TAS5186ADDV as the power stage of a multichannel Class-D audio system.
TAS5186DDV - 6-Channel 210W Class D Power Stage | TI
The Texas Instruments TAS5186DDV is a six-channel Class D digital-amplifier power stage rated for 210 W total output power, with 105 dB A-weighted SNR, less than 0.05% THD+N at 1 W, and greater than 90% power-stage efficiency at 1 W into the recommended single-ended loads. The device is housed in a 44-terminal HTSSOP package and operates from a 10.8 V to 13.2 V supply. A Class D power stage is an audio-amplifier output circuit that switches its supply rails at high frequency to produce a filtered audio waveform. It belongs to the amplifier IC hierarchy, where a digital-input power stage removes the need for external analog audio-input circuitry when it is paired with a compatible audio codec or digital-audio processor. Its principal advantages are high conversion efficiency, compact implementation, and integration of speaker-output protection. The TAS5186DDV provides six independent amplification channels for multichannel audio systems. Its published performance includes 105 dB A-weighted signal-to-noise ratio, THD+N below 0.05% at 1 W, and efficiency above 90% into recommended loads. Integrated protection covers undervoltage, overtemperature, overload, and short-circuit conditions, reducing the amount of discrete protection required around each speaker output. Digital inputs allow the amplifier to receive audio samples directly from an audio codec, DSP, or other digital-audio source. This architecture supports a compact signal chain and accurate channel synchronization. The 44-terminal HTSSOP package also provides a practical surface-mount footprint for multi-channel consumer and professional audio equipment, subject to careful thermal and layout design. Typical uses include powered speakers, soundbar amplifier boards, home-theater receiver power stages, active subwoofer systems, and compact multimedia speaker designs. Its six-channel architecture is particularly useful when one board must drive multiple surround-sound channels without implementing six separate discrete amplifier circuits. Designers should follow the manufacturer layout guidance for high-current speaker and power-ground paths, place the required decoupling capacitors close to the device, and verify copper area for thermal dissipation. Thermal performance depends on output power, channel utilization, load impedance, PCB copper, and ambient temperature, so a compact enclosure should be validated under worst-case multichannel conditions. This page combines the device's principal performance specifications, application guidance, design cautions, and identified pin-compatible family options for faster engineering selection. Use the manufacturer datasheet pin-description table and recommended application circuit when assigning PCB nets and confirming thermal limits.
TAS5186DDVR - 6-Channel 210W Class D Power Stage | TI (Tape & Reel)
The Texas Instruments TAS5186DDVR is a six-channel Class D digital-amplifier power stage rated for 210 W total output power, with 105 dB A-weighted SNR, less than 0.05% THD+N at 1 W, and greater than 90% power-stage efficiency at 1 W into the recommended single-ended loads. The device is housed in a 44-terminal HTSSOP package and operates from a 10.8 V to 13.2 V supply. A Class D power stage is an audio-amplifier output circuit that switches its supply rails at high frequency to produce a filtered audio waveform. It belongs to the amplifier IC hierarchy, where a digital-input power stage removes the need for external analog audio-input circuitry when it is paired with a compatible audio codec or digital-audio processor. Its principal advantages are high conversion efficiency, compact implementation, and integration of speaker-output protection. The TAS5186DDVR provides six independent amplification channels for multichannel audio systems. Its published performance includes 105 dB A-weighted signal-to-noise ratio, THD+N below 0.05% at 1 W, and efficiency above 90% into recommended loads. Integrated protection covers undervoltage, overtemperature, overload, and short-circuit conditions, reducing the amount of discrete protection required around each speaker output. Digital inputs allow the amplifier to receive audio samples directly from an audio codec, DSP, or other digital-audio source. This architecture supports a compact signal chain and accurate channel synchronization. The 44-terminal HTSSOP package also provides a practical surface-mount footprint for multi-channel consumer and professional audio equipment, subject to careful thermal and layout design. Typical uses include powered speakers, soundbar amplifier boards, home-theater receiver power stages, active subwoofer systems, and compact multimedia speaker designs. Its six-channel architecture is particularly useful when one board must drive multiple surround-sound channels without implementing six separate discrete amplifier circuits. Designers should follow the manufacturer layout guidance for high-current speaker and power-ground paths, place the required decoupling capacitors close to the device, and verify copper area for thermal dissipation. Thermal performance depends on output power, channel utilization, load impedance, PCB copper, and ambient temperature, so a compact enclosure should be validated under worst-case multichannel conditions. This page combines the device's principal performance specifications, application guidance, design cautions, and identified pin-compatible family options for faster engineering selection. Use the manufacturer datasheet pin-description table and recommended application circuit when assigning PCB nets and confirming thermal limits.
TAS5261DKD - 315W Mono Class D Amplifier | Texas Instruments
The Texas Instruments TAS5261DKD is a 315 W mono bridge-tied-load Class D digital amplifier power stage packaged in a 36-pin HSSOP. It is designed to drive 4- to 8-ohm speakers with low harmonic distortion, and its digital input architecture requires a simple passive demodulation filter to produce high-quality, high-efficiency audio amplification. A Class D amplifier is a switching audio power stage whose output switches between the supply rails to amplify a pulse-width-modulated signal. After passive low-pass demodulation, this approach can provide high output power with lower power loss than a conventional linear audio amplifier. The TAS5261DKD belongs to the digital amplifier power-stage hierarchy, where an external input-processing stage generates the required modulation signal and the integrated power stage supplies current to the speaker load. The TAS5261DKD provides one mono amplification channel, supports 4- to 8-ohm speakers, and is identified as a 315 W mono BTL digital amplifier power stage. The manufacturer documentation also describes the device as a 400 W mono Class D amplifier, while the product-page description identifies a 315 W configuration. Its listed operating supply range is 10.8 V to 13.2 V. Digital inputs, short-circuit protection, and thermal protection are listed among the device features. The implementation uses a passive demodulation filter between the switching output and the speaker rather than an analog audio input stage. This architecture supports efficient amplification at relatively high output power, but the filter must be selected and laid out correctly because its response determines the recovered audio bandwidth, attenuation of carrier-related artifacts, and speaker-load stability. Typical uses include powered speakers, subwoofer amplifiers, professional audio equipment, consumer audio systems, and other mono loudspeaker applications operating from a 12 V-class supply. A bridge-tied-load configuration uses both output terminals to drive the speaker differentially, so the speaker remains connected between the two outputs rather than from one output to ground. PCB design should prioritize short power-stage connections, adequate thermal copper, a continuous supply path, careful grounding, and a stable reference return. The passive demodulation network should be placed close to the power-stage output, and its component values must follow the manufacturer reference design. Adequate copper area is important because Class D output current and supply transients can create losses, voltage drops, and EMI coupling even when the amplifier operates efficiently. This page combines the identified electrical ratings, package characteristics, application guidance, and manufacturer documentation links for engineering evaluation. It also distinguishes verified product facts from unspecified details so designers can consult the pin-description table, reference schematic, thermal guidance, and power calculations before committing a TAS5261DKD design to production.
TAS5261DKDR - 315W Mono Class D Power Stage | Texas Instruments
The Texas Instruments TAS5261DKDR is a 315 W mono bridged-load-tie class D digital power stage packaged in a 36-terminal HSSOP. It is designed for high-efficiency audio amplification where a compact solution must deliver substantial continuous output power to a low-impedance loudspeaker. The device accepts digital audio data and operates as a mono class D output stage, supporting compact consumer and professional audio systems. A class D power stage is a switching amplifier topology that controls current through the speaker output at high frequency. Compared with a linear audio amplifier, the switching approach reduces the power dissipated in the output devices and enables high output power with smaller magnetic components. In the wider power-management hierarchy, the TAS5261 belongs to the class D amplifier family, which falls under audio amplifier ICs and, more broadly, power management semiconductors. Key characteristics include 315 W rated mono output power, a single-channel class D architecture, a 36-HSSOP package, and a bridged-load-tie speaker configuration. The HSSOP package uses a gull-wing surface-mount form factor and exposes a thermal pad for heat removal when the device is mounted according to the manufacturer's recommended land pattern. Its operating voltage, output-stage limits, thermal characteristics, and signal-interface timing should be confirmed against the specific version of the manufacturer datasheet before layout release. Typical implementations include powered speakers, compact home-theater enclosures, soundbars, multimedia speaker systems, subwoofer amplifier modules, and industrial audio products driven by an external audio processor. Because the device is a power stage rather than a complete codec-equipped amplifier, upstream circuitry must supply the required digital audio stream and control signals. A properly designed LC output filter is required to remove high-frequency switching energy before the loudspeaker. Layout is the dominant design consideration. Place the input, control, power, and output-network connections according to the datasheet reference layout, minimize loop area in high-current switching paths, and provide substantial copper area for thermal dissipation. Verify junction temperature at worst-case supply voltage, output power, and ambient temperature rather than relying on nominal board temperature alone. This page adds application-focused implementation guidance, pin-compatible sourcing information, and a structured comparison of the documented operating characteristics. Use the manufacturer datasheet and reference layout as the controlling documents for production design, EMC tuning, and thermal validation.
TAS5342DDV - 100W Stereo Class D Power Stage | Texas Instruments
Texas Instruments TAS5342DDV is a 100-W stereo digital amplifier power stage designed for Class D audio systems, supplied in a 44-HTSSOP package. The device is intended for stereo or bridge-tied-load (BTL) configurations and supports speaker loads up to 8 ohm. Its integrated digital power-stage design is intended to provide high output power with low harmonic distortion, low integrated noise, and low idle current for audio receivers, powered speakers, soundbars, and other compact audio systems. A digital Class D power stage is a semiconductor amplifier category that converts a digital audio signal into a high-current switching waveform and then reconstructs the audio output through the speaker and output filtering network. Within the power-management hierarchy, the TAS5342DDV combines an audio amplifier, power conversion function, output-driver capability, and integrated fault protection in one power-management IC. It is commonly paired with an audio DSP or digital-audio interface that generates the required PWM signals. The TI product page identifies the TAS5342 as a high-performance integrated stereo digital amplifier power stage capable of driving a bridge-tied load at up to 100 W per channel. The listed operating power-supply range is 0 V to 34 V, with a typical supply range of 10.8 V to 13.2 V. The device supports differential input and differential output arrangements, which help reject common-mode noise and allow flexible speaker-routing configurations. The integrated protection system is a major functional feature. Texas Instruments describes protection against multiple fault conditions, including output-related faults that could otherwise damage the power stage or connected speaker network. The 44-HTSSOP package provides a high pin count for power connections, signal routing, control functions, and thermal management. Because power amplifiers dissipate energy in their output stages, correct copper area, thermal-pad layout, heat spreading, and enclosure ventilation are essential in practical designs. Typical applications include powered stereo speakers, home-theater receivers, compact soundbars, multimedia speakers, and other consumer audio equipment. The 100-W-per-channel capability is useful when the loudspeaker load is nominally 8 ohm and the amplifier is operated within the manufacturer-recommended supply and thermal limits. The differential output structure also makes the device suitable for BTL speaker connections, where each channel drives the speaker differentially. For implementation, follow the pin-description table and recommended application circuit in the manufacturer datasheet when assigning the 44-HTSSOP land pattern. Keep the power-stage supply and output-current paths compact, provide adequate input and output filtering, and confirm that the exposed thermal pad is connected to the intended ground and copper area. The amplifier should not be selected solely by its headline wattage; speaker impedance, supply voltage, thermal dissipation, modulation scheme, and output-filter requirements determine the practical result. This page summarizes the key electrical, packaging, protection, and application characteristics of the TAS5342DDV and organizes them for faster design review. It also identifies the limits of directly replacing a power-stage IC: a valid drop-in candidate must match the package, pinout, supply assumptions, output architecture, and thermal requirements rather than merely share a similar wattage rating.
TAS5342DDVR - 100W Stereo Class D Power Stage | Texas Instruments (Tape & Reel)
Texas Instruments TAS5342DDVR is a 100-W stereo digital amplifier power stage designed for Class D audio systems, supplied in a 44-HTSSOP package. The device is intended for stereo or bridge-tied-load (BTL) configurations and supports speaker loads up to 8 ohm. Its integrated digital power-stage design is intended to provide high output power with low harmonic distortion, low integrated noise, and low idle current for audio receivers, powered speakers, soundbars, and other compact audio systems. A digital Class D power stage is a semiconductor amplifier category that converts a digital audio signal into a high-current switching waveform and then reconstructs the audio output through the speaker and output filtering network. Within the power-management hierarchy, the TAS5342DDVR combines an audio amplifier, power conversion function, output-driver capability, and integrated fault protection in one power-management IC. It is commonly paired with an audio DSP or digital-audio interface that generates the required PWM signals. The TI product page identifies the TAS5342 as a high-performance integrated stereo digital amplifier power stage capable of driving a bridge-tied load at up to 100 W per channel. The listed operating power-supply range is 0 V to 34 V, with a typical supply range of 10.8 V to 13.2 V. The device supports differential input and differential output arrangements, which help reject common-mode noise and allow flexible speaker-routing configurations. The integrated protection system is a major functional feature. Texas Instruments describes protection against multiple fault conditions, including output-related faults that could otherwise damage the power stage or connected speaker network. The 44-HTSSOP package provides a high pin count for power connections, signal routing, control functions, and thermal management. Because power amplifiers dissipate energy in their output stages, correct copper area, thermal-pad layout, heat spreading, and enclosure ventilation are essential in practical designs. Typical applications include powered stereo speakers, home-theater receivers, compact soundbars, multimedia speakers, and other consumer audio equipment. The 100-W-per-channel capability is useful when the loudspeaker load is nominally 8 ohm and the amplifier is operated within the manufacturer-recommended supply and thermal limits. The differential output structure also makes the device suitable for BTL speaker connections, where each channel drives the speaker differentially. For implementation, follow the pin-description table and recommended application circuit in the manufacturer datasheet when assigning the 44-HTSSOP land pattern. Keep the power-stage supply and output-current paths compact, provide adequate input and output filtering, and confirm that the exposed thermal pad is connected to the intended ground and copper area. The amplifier should not be selected solely by its headline wattage; speaker impedance, supply voltage, thermal dissipation, modulation scheme, and output-filter requirements determine the practical result. This page summarizes the key electrical, packaging, protection, and application characteristics of the TAS5342DDVR and organizes them for faster design review. It also identifies the limits of directly replacing a power-stage IC: a valid drop-in candidate must match the package, pinout, supply assumptions, output architecture, and thermal requirements rather than merely share a similar wattage rating.
TAS5352DDV 125W Stereo Class-D Power Stage | Texas Instruments
The Texas Instruments TAS5352DDV is an integrated stereo digital Class-D amplifier power stage designed to drive a 4 ohm bridge-tied load at up to 125 W per channel. It operates from a 10.8 V to 13.2 V supply and is packaged in a 44-pin HTSSOP with an exposed thermal pad. The device provides a high-efficiency speaker-drive solution with low harmonic distortion, low integrated noise, and low idle current. A digital Class-D audio power amplifier is a power-management IC that switches its output stage rapidly between voltage states to reproduce an audio waveform. Its efficiency is generally higher than that of a conventional linear amplifier because the switching stage dissipates less power when driving a speaker load. Bridge-tied-load operation applies the audio waveform across the two speaker terminals, increasing the available output voltage and power without requiring a physical ground connection at the speaker. The TAS5352DDV integrates a stereo output stage and a complete on-chip protection system. Its principal output rating is 125 W per channel into a 4 ohm BTL load, while its listed operating supply range is 10.8 V to 13.2 V. The device is specified for low harmonic distortion and low integrated noise, making it suitable for compact high-power audio systems. Its low idle current can also reduce standby dissipation when the associated system power architecture requires low quiescent consumption. TAS5352 is positioned as a power stage rather than a complete audio input amplifier. A practical system therefore needs a source capable of supplying the appropriate input signal, control or codec circuitry where required, output filtering, and a correctly designed speaker network. The manufacturer documents internal pull-up resistors to 3.3 V on the SD and OTW outputs; external pull-up resistors can provide 5 V logic level compliance where that interface voltage is required. Typical uses include powered speakers, compact home-theater systems, professional audio equipment, soundbars, subwoofer power modules, and other high-efficiency speaker-drive products. A 10.8 V to 13.2 V supply is particularly compatible with systems organized around a 12 V rail, although final rail limits, startup behavior, current demand, and protection requirements must be evaluated against the complete amplifier design. Thermal design is central to achieving the 125 W per-channel rating. The exposed-pad HTSSOP construction requires a low-impedance PCB thermal path, adequate copper area, and suitable airflow or enclosure heat transfer. Decoupling capacitors must be placed close to the supply and ground pins, and output-filter layouts must keep high-current switching paths compact. Speaker wiring, connectors, and load selection must also support the intended channel power. This page consolidates the verified device identity, package information, operating limits, interface details, and drop-in assessment into an engineering-focused reference. It also distinguishes documented functional similarity from true pin-to-pin equivalence, helping designers avoid treating a related part as an automatic replacement without completing a footprint, signal, control, and thermal review.
TAS5352DDVR 125W Stereo Class-D Power Stage | Texas Instruments (Tape & Reel)
The Texas Instruments TAS5352DDVR is an integrated stereo digital Class-D amplifier power stage designed to drive a 4 ohm bridge-tied load at up to 125 W per channel. It operates from a 10.8 V to 13.2 V supply and is packaged in a 44-pin HTSSOP with an exposed thermal pad. The device provides a high-efficiency speaker-drive solution with low harmonic distortion, low integrated noise, and low idle current. A digital Class-D audio power amplifier is a power-management IC that switches its output stage rapidly between voltage states to reproduce an audio waveform. Its efficiency is generally higher than that of a conventional linear amplifier because the switching stage dissipates less power when driving a speaker load. Bridge-tied-load operation applies the audio waveform across the two speaker terminals, increasing the available output voltage and power without requiring a physical ground connection at the speaker. The TAS5352DDVR integrates a stereo output stage and a complete on-chip protection system. Its principal output rating is 125 W per channel into a 4 ohm BTL load, while its listed operating supply range is 10.8 V to 13.2 V. The device is specified for low harmonic distortion and low integrated noise, making it suitable for compact high-power audio systems. Its low idle current can also reduce standby dissipation when the associated system power architecture requires low quiescent consumption. TAS5352 is positioned as a power stage rather than a complete audio input amplifier. A practical system therefore needs a source capable of supplying the appropriate input signal, control or codec circuitry where required, output filtering, and a correctly designed speaker network. The manufacturer documents internal pull-up resistors to 3.3 V on the SD and OTW outputs; external pull-up resistors can provide 5 V logic level compliance where that interface voltage is required. Typical uses include powered speakers, compact home-theater systems, professional audio equipment, soundbars, subwoofer power modules, and other high-efficiency speaker-drive products. A 10.8 V to 13.2 V supply is particularly compatible with systems organized around a 12 V rail, although final rail limits, startup behavior, current demand, and protection requirements must be evaluated against the complete amplifier design. Thermal design is central to achieving the 125 W per-channel rating. The exposed-pad HTSSOP construction requires a low-impedance PCB thermal path, adequate copper area, and suitable airflow or enclosure heat transfer. Decoupling capacitors must be placed close to the supply and ground pins, and output-filter layouts must keep high-current switching paths compact. Speaker wiring, connectors, and load selection must also support the intended channel power. This page consolidates the verified device identity, package information, operating limits, interface details, and drop-in assessment into an engineering-focused reference. It also distinguishes documented functional similarity from true pin-to-pin equivalence, helping designers avoid treating a related part as an automatic replacement without completing a footprint, signal, control, and thermal review.
TAS5508APAG - 8-Channel Digital Audio PWM Processor | Texas Instruments
The Texas Instruments TAS5508APAG is an 8-channel digital audio PWM processor for high-fidelity multichannel audio systems, housed in a 64-pin TQFP package measuring 10 x 10 mm. It supports sample rates from 32 kHz to 192 kHz and is categorized as a digital audio PWM processor and audio modulator. The device interfaces digital audio signals with external amplifier stages, providing centralized control for multichannel Class-D audio architectures. A digital audio PWM processor is a specialized interface IC that converts or prepares digital audio data for power-amplifier stages. It sits between an audio DSP, codec, or source controller and the power-amplifier output network. Within the signal chain, the hierarchy is digital audio processor, audio interface IC, PWM modulator, and power-management semiconductor. Integrating eight channels in one package reduces the number of separate control devices required for surround-sound and multichannel installations. The TAS5508APAG combines an 8-channel architecture with support for audio sample rates up to 192 kHz. This makes it appropriate for high-resolution consumer and professional audio systems operating at standard CD, DVD, multichannel cinema, and higher-rate digital audio sampling frequencies. Its 64-TQFP package provides a substantial number of external connections for digital audio data, clock signals, control signals, and power connections. The processor integrates digital control for eight audio output channels and is designed to operate with compatible digital signal processors and audio power stages. Automatic control configuration in response to clock and data conditions is associated with the TAS5508 family, helping the device adapt to changing digital-audio operating states. System designers should use the manufacturer pin-description table and reference circuit when assigning the complete 64-pin land pattern. Typical uses include 5.1-channel and 7.1-channel home-theater systems, professional digital mixing consoles, active speaker networks, automotive audio systems, and powered multiway speakers. The eight-channel architecture is particularly useful where a single DSP must distribute synchronized control across multiple Class-D amplifier channels. The device is also suitable for high-resolution installations operating with audio sample rates between 32 kHz and 192 kHz. Layout is critical because high-channel-count digital audio processors combine clock-sensitive signals with power-supply connections in a 10 x 10 mm TQFP footprint. Keep clock and data traces short, route them away from switching-node and power-converter traces, and place decoupling capacitors close to their associated supply pins. Follow the manufacturer’s recommended component values and pin-specific connection instructions to avoid signal-integrity problems. This page consolidates the device identity, package information, supported sample-rate range, sourcing information, compatible family references, and practical implementation guidance into one engineering-focused reference. It helps engineers separate confirmed product characteristics from details that require direct verification against the current Texas Instruments datasheet.
TAS5518PAG - 8-Channel Digital Audio PWM Processor | Texas Instruments
Texas Instruments TAS5518PAG is an 8-channel digital audio PWM processor with a typical system dynamic range of 110 dB and a 64-pin TQFP (PAG) package. The device integrates digital audio processing, power-supply volume control, and multi-channel PWM output functionality into one audio-focused system IC. It is intended for designs that require coordinated audio-channel control without implementing eight separate digital input channels and PWM output stages. A digital audio PWM processor is a mixed-signal audio IC that accepts digital audio information and controls PWM-based amplifier stages. Within the audio signal-chain hierarchy, it sits between a digital audio source and a power-amplifier or speaker-driving circuit. Unlike a conventional analog power amplifier, the TAS5518PAG manages digital modulation data, volume-related functions, and channel integration, allowing the connected amplifier stage to reproduce the intended audio signal. The principal system benefit is high integration. According to the Texas Instruments product information, the TAS5518PAG supports eight digital audio channels in one device. A well-designed system can achieve typical dynamic range of 110 dB, while the power supply volume control feature provides up to 24 dB of additional dynamic range at normal listening levels. This combination can reduce external control-component complexity and centralize audio-volume behavior across multiple channels. The TAS5518PAG also provides direct support for digital-audio signal processing before the PWM output stage. This architecture is appropriate for multichannel consumer-audio equipment where synchronized channel control and system-level volume management are more important than a conventional standalone analog output stage. Its 64-pin TQFP (PAG) package provides the pin count needed for multichannel digital interfaces, control signals, power connections, and multiple PWM outputs. Typical uses include powered speakers, soundbars, home-theater audio systems, active speakers, multichannel audio receivers, and compact consumer audio products. The device can serve as the central PWM processor in an eight-channel signal path when its digital interface, output arrangement, and power architecture align with the selected amplifier topology. Board-level implementation must account for clean power, grounded return paths, signal integrity, and thermal performance. Designers should verify the complete pin arrangement, recommended external components, interface timing, and power-supply requirements in the manufacturer datasheet before routing a new PCB. Because this orderable designation is marked as not recommended for new designs, new products should first evaluate TI's current alternate-part recommendations and confirm functional, firmware, and mechanical compatibility rather than assuming direct interchangeability. This page consolidates the device classification, verified package information, lifecycle position, candidate replacement information, and practical selection guidance. It also distinguishes confirmed drop-in information from broader functional alternatives, helping engineers make a defensible sourcing decision without treating similar audio processors as footprint-compatible substitutes.
TAS5518PAGR - 8-Channel Digital Audio PWM Processor | Texas Instruments
Texas Instruments TAS5518PAGR is an eight-channel digital audio PWM processor with a typical system dynamic range of 110 dB, PSVC support for up to 24 dB of additional dynamic range, and a 64-pin TQFP package measuring 10 x 10 mm. It accepts digital audio data and generates PWM drive signals for eight Class-D amplifier channels. A digital audio PWM processor is a mixed-signal audio IC that combines digital control, modulation, and output-driver functions in one device. It sits between an audio source, such as a digital audio interface or decoder, and power-amplifier stages. The TAS5518 integrates channel volume control, modulation, and system-level audio management to reduce the number of external discrete components required by multichannel audio systems. Principal features include eight audio channels, a 110 dB typical dynamic range in a well-designed system, and a power supply volume control feature that can contribute up to 24 dB of additional dynamic range at normal listening levels. Its 3 V to 3.6 V operating supply range supports integration with common low-voltage digital audio platforms, while the 64-pin TQFP package provides adequate routing density for eight-channel outputs. The architecture is designed to preserve audio quality while concentrating channel-level processing and PWM generation on one IC. Digital command and control information can be used to configure the multichannel system, and the PSVC function provides additional headroom relative to a fixed system operating level. This makes the processor useful where channel imbalance, small-signal dynamic-range limitations, or the cost of multiple external control paths would otherwise constrain the design. Typical uses include powered speakers, sound bars, home-theater receivers, active speaker networks, automotive audio systems, and other consumer or professional products requiring multiple Class-D amplifier channels. A practical implementation must preserve clean digital and analog ground returns, decouple the supply close to the device, and route high-current PWM outputs as controlled-impedance signals rather than treating them as ordinary low-frequency logic nets. Careful PCB partitioning is essential because the device combines digital control with timing-sensitive PWM outputs. Keep communication traces away from output nodes, use the manufacturer-recommended power and ground layout, and provide adequate copper around exposed thermal and power-distribution structures. Confirm the external clock, serial interface, and reset implementation against the manufacturer datasheet before releasing the PCB. This product page combines the manufacturer device description, package and channel details, lifecycle information, drop-in replacement assessment, application guidance, and practical layout considerations. It is intended to help engineers evaluate the TAS5518PAGR for multichannel digital-audio architectures and compare it with identified same-family devices without obscuring package or feature differences.
TAS5548DCA - 8-Channel 96kHz PWM Audio Processor | TI
The Texas Instruments TAS5548DCA is an 8-channel digital pulse-width-modulation audio processor with digital audio processing, an integrated asynchronous sample-rate converter, and a 96 kHz PWM output stage, housed in a 56-pin HTSSOP package. It combines eight-channel audio processing with integrated sample-rate conversion to support high-definition home-theater signal paths. An audio processor is a specialized interface IC that manages digital audio data between source devices and power-conversion stages. Within the broader hierarchy, the TAS5548DCA belongs to digital audio processing, audio system semiconductors, and power-management signal-chain components. Its PWM outputs provide a digital representation of audio waveforms for downstream amplification and speaker-drive circuitry. The device includes two asynchronous sample-rate-converter modules, with each module handling four channels. This arrangement allows the processor to support multichannel operation and aligns it with DTS-HD-compatible Blu-ray home-theater-in-a-box applications identified by Texas Instruments. The architecture also consolidates digital audio processing, sample-rate conversion, and eight-channel PWM modulation into one package. TAS5548DCA is controlled through an external I2C interface, enabling an embedded host or audio system controller to configure the processor and manage its operating state. Integrating digital control with multichannel PWM output reduces the number of separate functional blocks needed in compatible home-theater and powered-speaker systems while preserving a centralized digital signal path. Typical implementation areas include DTS-HD-compatible Blu-ray home-theater systems, multichannel powered speakers, digital active loudspeakers, home-theater processor boards, and other audio equipment requiring eight PWM channels. The 56-pin HTSSOP package is designed for surface-mount assembly, while the stated operating-temperature range is 0°C to +85°C. Layout planning should prioritize short, controlled connections among the digital-audio inputs, I2C control interface, ground network, supply rails, and PWM outputs. Because the device combines high-channel-count processing with a fine-pitch surface-mount package, careful decoupling and return-path design are essential for reliable signal transfer and thermal performance. This page combines the manufacturer product information with practical distinctions for evaluating the TAS5548DCA, including its 8-channel architecture, 96 kHz PWM operation, integrated ASRC, package format, application fit, and the documentation needed for PCB and firmware planning.
TAS5601DCA - 20W Stereo Class-D Amplifier | Texas Instruments
Texas Instruments TAS5601DCA is a 20 W per channel digital Class-D audio amplifier power stage with a 10 V to 26 V supply and PWM single-ended input. The device is supplied in a 56-pin HTSSOP (DCA) package and can configure its four half-bridge outputs for stereo bridge-tied loads, four single-ended loads, or a mixture of both. A digital Class-D audio amplifier is a switching power stage that uses pulse-width-modulated drive signals to deliver power efficiently to loudspeakers. Unlike a conventional linear audio amplifier, the TAS5601 converts the PWM input into high-frequency switching currents, reducing the amount of power dissipated within the output stage. The TAS5601 belongs to the Class-D amplifier hierarchy, where its four half bridges provide the switching elements required for stereo speaker drive. The principal operating specifications are 20 W per channel, a 10 V to 26 V supply range, and PWM single-ended input. The amplifier is designed for speakers with an impedance as low as 4 ohms. According to the manufacturer datasheet, Rev. A, efficiency exceeds 90% when driving an 8-ohm load. This efficiency figure is especially useful when comparing thermal requirements with less efficient linear amplification approaches. Each output half bridge includes integrated feedback support, allowing the amplifier to operate with a conventional speaker connection rather than requiring a separate analog output filter. The device supports two bridge-tied speakers or four single-ended speakers, and the same output network can also be arranged for a combination of single-ended and bridge-tied loads. The resulting flexibility permits speaker-count changes without changing the amplifier package or control architecture. Typical uses include powered speakers, stereo audio receivers, multimedia speaker systems, sound bars, consumer television equipment, and compact audio products requiring multiple speaker outputs. The 10 V to 26 V supply range is suited to systems using a 12 V or 24 V rail, while the four-half-bridge architecture is useful when the design must accommodate both stereo and multiway speaker configurations. Design the power rails, output inductors, speaker connections, and thermal copper around the maximum 26 V operating condition. Speaker wiring and amplifier outputs must be kept away from sensitive signal paths, and the PCB layout should follow the manufacturer reference layout to control switching noise, ground bounce, and unintended electromagnetic coupling. This page organizes the verified operating characteristics, amplifier configuration options, sourcing information, and engineering trade-offs around the TAS5601DCA. It also distinguishes genuine drop-in alternatives from package or ordering-code variations so that PCB reuse decisions remain based on pin compatibility rather than nominal power capability alone.
TAS5601DCAR - 20W Stereo Class-D Amplifier | Texas Instruments
Texas Instruments TAS5601DCAR is a 20 W-per-channel stereo Class-D digital amplifier power stage with PWM single-ended input, a 10 V to 26 V supply range, and a 56-pin HTSSOP DCA package. It supports four single-ended speakers, two bridge-tied speakers, or a mixture of single-ended and bridge-tied loads, including speaker impedances as low as 4 Ω. A Class-D audio amplifier is a switching power amplifier that uses pulse-width modulation to represent an analog audio waveform. Within the amplifier hierarchy, it belongs to the digital amplifier family, power-stage IC category, and broader audio power-management semiconductor group. Compared with a linear audio amplifier, a Class-D stage can deliver high output efficiency while placing less heat in the speaker and amplifier output stages. The TAS5601 is designed as a power stage that accepts a digital audio signal and drives speakers without requiring the traditional analog input-voltage signal path. The headline specifications are 20 W per channel, a 10 V to 26 V supply range, and greater than 90% efficiency into an 8 Ω load. The device can operate as a 2-channel stereo amplifier or a 4-channel single-ended amplifier. Its digital interface supports the common audio-system use cases for compact consumer, multimedia, and powered-speaker products. An operating-temperature range of −40 °C to 85 °C and a surface-mount HTSSOP package support industrial and commercial equipment designs. The TAS5601 uses a feedback-based Class-D power-stage architecture, with the option to drive either bridge-tied or single-ended loads. Feedback-based operation helps the output stage track the intended signal while maintaining low distortion in the target application. The manufacturer identifies efficiency above 90% into an 8 Ω load as sufficient to eliminate the need for an external heat sink in typical configurations. Actual thermal performance still depends on supply voltage, channel loading, board copper, ambient temperature, and the duration of maximum-power operation. Typical applications include compact stereo speakers, multimedia speaker systems, soundbars, television audio modules, portable consumer equipment, and powered peripheral systems. The 4 Ω minimum load capability gives designers flexibility when selecting conventional speaker impedances. The digital input architecture is particularly useful where the audio source already delivers a digital signal, allowing the power stage to be placed close to the speaker connector and away from sensitive source circuitry. PCB design should prioritize short power-loop paths, continuous output-current copper, thermal-via placement beneath the exposed pad, and clean separation between input and output routing. The HTSSOP thermal pad must be connected to the intended ground plane with multiple vias, and output filtering must follow the manufacturer reference layout to control switching-related interference. Component placement should also minimize loop area around the power supply and output bridge. This product page consolidates the official device specifications, pin-compatible-replacement assessment, application guidance, comparison parameters, and practical layout considerations into a design-focused reference. It helps engineers distinguish electrical compatibility from mere package similarity while planning amplifier routing, speaker loading, thermal management, and sourcing.
TAS5602DCA - 20W Stereo PWM-Input Class-D Power Stage | TI
The Texas Instruments TAS5602DCA is a 20 W per channel stereo digital Class-D audio amplifier power stage with PWM input, housed in a 56-pin HTSSOP (DCA) package with an exposed thermal pad. It operates from a 10 V to 26 V supply and can drive four single-ended speakers or two bridge-tied (BT) speakers from a single device. A Class-D audio amplifier is a switching power amplifier that delivers audio output by applying a constant-amplitude PWM carrier to the speaker load, so the transistor output stage conducts only when the PWM signal is active. In the device hierarchy, TAS5602DCA belongs to the amplifier IC family, inside audio amplifiers, inside integrated circuits, inside analog power and signal-chain semiconductors. Unlike a conventional analog input amplifier, this part accepts a PWM signal directly from a digital audio processor or a Class-D modulator, eliminating an analog input stage and its associated noise and distortion. Key features include 20 W of continuous output power per channel, a wide 10 V to 26 V operating supply range, and support for both single-ended and bridge-tied speaker configurations. Because the part accepts PWM rather than an analog voltage, the noise floor is set entirely by the upstream digital source, which keeps inter-channel noise and distortion very low and makes channel matching essentially perfect. The device supports 2-channel stereo, 4-channel quad, and mono operation modes, giving a single part number flexibility for multiple speaker topologies. Internally, the TAS5602 architecture combines a half-bridge output stage with integrated feedback control, so the amplifier can be configured with or without a feedback resistor network to suit the target speaker impedance. Because output stage switching is fully synchronous and the modulator runs at a high carrier frequency, the switching losses remain low and the power stage can be mounted on standard two-layer PCB copper without a bulky external heatsink in typical 10 W per channel designs. Typical applications include consumer and industrial audio: multi-room and networked speakers, sound bars, TV and monitor speaker drivers, Bluetooth and Wi-Fi speaker systems, USB and PC audio docks, and powered speaker systems. The 56-pin HTSSOP package with exposed pad provides a large thermal copper area, which is essential for continuous 20 W per channel operation from a 24 V rail. When laying out the board, treat the exposed pad as both the thermal path and the main ground return. Use a solid ground pour with minimal inductance between the output drivers and the supply bypass capacitors, and place the input PWM traces away from the switching node to avoid coupling the carrier frequency into the audio path. This page brings together the manufacturer ordering information, a parameter-by-parameter comparison against related Texas Instruments Class-D power stages, and practical thermal and layout guidance that goes beyond the headline specifications found in the datasheet.