Amplifier ICs
بەرهەمەکان (3,200+)
TAS5760MDAP - 55W Stereo Class-D Amplifier | Texas Instruments
The Texas Instruments TAS5760MDAP is a digital-input Class-D audio amplifier with 55 W stereo output power, 114 W mono output power, a 4.5 V to 26.4 V supply range, and a 32-pin HTSSOP package. It accepts I2S digital audio and provides integrated Class-D output stages, digital clipping control, configurable gain, and hardware or I2C control modes. The device also includes integrated headphone circuitry and is designed for compact, high-efficiency audio systems. A Class-D audio amplifier is a switching power amplifier that uses pulse-width-modulated output drive to deliver audio through a speaker load. Compared with conventional linear output stages, Class-D architecture improves power-conversion efficiency and reduces the amount of heat that must be removed from the PCB. Within the broader semiconductor hierarchy, TAS5760MDAP is an audio power amplifier, a digital-input amplifier, and a power-management IC for portable and embedded consumer equipment. The TAS5760MD family combines a wide operating range with flexible digital control. Its integrated digital clipper helps control clipping behavior, while several selectable gain options let system designers balance sensitivity against signal headroom. Hardware and I2C control modes support both simple fixed configurations and software-controlled operation. An integrated headphone path adds another audio-output option without requiring a separate headphone driver in designs that need both speaker and headphone outputs. Class-D efficiency depends on the output power stage and its load. The manufacturer datasheet identifies a 120 mΩ power-stage RDS(on), which helps characterize conduction loss and helps designers estimate heat dissipation in the power stage. The 32-pin PowerPAD HTSSOP package provides a thermal pad for heat transfer, but its effectiveness still depends on PCB copper area, via distribution, airflow, and the sustained output level. Typical uses include portable speakers, smart-home display audio, compact consumer speakers, multimedia equipment, and I2S-enabled products that benefit from a digital audio path. It is also appropriate for systems where one amplifier must support either stereo speaker operation or a higher-power mono configuration. Digital source selection and gain configuration can be handled through I2C in platforms with an embedded host processor. Power-supply and layout design remain the main implementation considerations. Keep the amplifier supply decoupling close to the device, provide adequate copper around the exposed thermal pad, and use low-inductance routing for the Class-D outputs. The speaker filter network must be placed where it provides the required transition behavior without allowing excessive switching current to reach sensitive audio circuitry. Confirm thermal performance at the highest expected output power and worst-case ambient temperature. This page combines the manufacturer’s headline electrical limits with practical thermal, layout, and selection guidance. It also distinguishes true pin-compatible alternatives from related parts that merely share the same package, preventing a superficially similar amplifier from being treated as an unqualified board-level replacement.
TAS5760MDCA - 55W Stereo Class-D Audio Amplifier | Texas Instruments
The Texas Instruments TAS5760MDCA is a digital-input Class-D audio amplifier rated for 55 W stereo output and 114 W mono output, with a 4.5 V to 26.4 V power-supply range and integrated high-pass filtering. The device accepts I2S digital audio and is offered in a 32-HTSSOP package for compact consumer and industrial audio systems. A Class-D audio amplifier is a switching amplifier that uses efficient power-conversion stages to drive speakers. The hierarchy places the TAS5760MDCA among Class-D amplifiers, digital input amplifiers, audio amplifiers, and integrated power-management semiconductors. Its digital input architecture avoids passing analog audio through a long signal path before amplification, while the Class-D output stage converts that digital stream into a high-power speaker drive. Principal features include 55 W stereo operation, 114 W mono operation, a 4.5 V to 26.4 V supply range, I2S input, and integrated high-pass filtering. The stereo and mono ratings provide useful flexibility for consumer audio, industrial sound systems, and compact powered speakers. Hardware and software I2C control modes support configuration of amplifier behavior, and the device family provides multiple gain options and digital clip protection for practical system integration. The TAS5760MDCA supports both stereo and mono output arrangements, allowing the same amplifier platform to address conventional two-channel systems or higher-power single-channel installations. Because its input is digital, the device is best suited to systems in which a host processor, digital audio decoder, or application processor supplies I2S data. Supply, output-stage, control-interface, and thermal requirements still need to be evaluated together when planning the power supply and PCB layout. Typical applications include powered smart speakers, soundbars, television audio, compact stereo systems, and industrial or IoT audio nodes. The integrated high-pass filter can help remove unwanted low-frequency content from the reproduced signal, while digital control simplifies setup. The package and digital interface are particularly useful where PCB area, signal repeatability, and centralized configuration matter more than accepting an analog input directly. Design the PCB around the manufacturer's power-supply and output-stage layout guidance, keeping high-current paths compact and providing adequate thermal copper around the power device. Decoupling should follow the application circuit, and I2C routing should avoid high-current switching nodes. Confirm speaker impedance, power limits, heat dissipation, and control sequencing against the manufacturer datasheet before production release. This page combines the verified product identity, package information, operating-range details, family-level compatibility information, drop-in alternatives, and engineering selection guidance. It is designed to help designers identify the correct amplifier and prepare a practical implementation plan without treating package compatibility as a substitute for full electrical verification.
TAS5782MDCA - 20W Stereo Class-D Amplifier | Texas Instruments
The Texas Instruments TAS5782MDCA is a 2-channel stereo Class-D smart audio amplifier with digital input, integrated audio processing, and up to 96-kHz processing architecture. It delivers 20 W per channel into stereo loads or 40 W in mono operation, operates from 4.5 V to 26.4 V, and is offered in a 48-pin HTSSOP (DCA) surface-mount package. Differential inputs, short-circuit protection, and thermal protection support robust loudspeaker drive applications. A Class-D amplifier is a switching power stage that delivers audio through a high-frequency carrier and an output filter. The TAS5782M belongs to the smart audio amplifier family, adding digital signal processing and digital input control to the basic Class-D output stage. Its 48-pin HTSSOP package combines the amplifier channels, digital interface, processing functions, and power-delivery pins in a single surface-mount component. Key features include 20 W stereo output, 40 W mono capability, a 4.5 V to 26.4 V supply range, and processing based on a 96-kHz architecture. The 26.4 V maximum supply voltage supports high-voltage audio systems, while the lower operating limit permits use with common single-cell lithium battery systems. The digital-input architecture avoids passing analog audio through a long board-level signal path. The device uses closed-loop Class-D operation, in which the amplifier monitors its output to reduce distortion and improve linearity. Integrated protection functions include short-circuit and thermal protection. Because the package combines analog power conversion, digital control, and signal processing, layout must separate sensitive digital and analog connections from the high-current switching and loudspeaker-output paths. Typical applications include sound bars, smart speakers, television and monitor audio, wireless speakers, compact consumer audio systems, and multimedia equipment. In a sound bar, the device can drive stereo speaker pairs while receiving a digital audio stream from a source processor. In a smart speaker, its digital input can shorten the analog signal chain and reduce susceptibility to board-level noise. Layout should provide a low-impedance ground and supply plane, place input and decoupling capacitors close to their associated pins, and route output-node and high-current supply paths away from signal and control pins. Thermal performance depends on the PCB copper area available for heat dissipation and on the sustained output power, so verify junction-temperature margin at the highest expected channel load. This page organizes the device specifications, pin-package information, application guidance, comparison details, and practical design considerations into one engineering reference. It also documents the constraints that determine when the TAS5782MDCA is appropriate and where a different amplifier or package option should be considered.
TAS5805MPWP - 23W Stereo Class-D Audio Amplifier | Texas Instruments
The Texas Instruments TAS5805MPWP is a 23 W stereo, 45 W mono, inductor-less Class-D audio amplifier with digital input, a 4.5 V to 26.4 V supply range, and a 28-pin HTSSOP package. Its closed-loop architecture and integrated audio processor support efficient speaker drive with low standby power dissipation. A Class-D audio amplifier is a switching power amplifier that uses a high-frequency PWM output stage to deliver audio energy to a speaker. It belongs to the hierarchy of audio amplifiers, linear audio amplifiers, and power-management semiconductors. Compared with a conventional linear output stage, the TAS5805M architecture is intended to reduce power loss and provide a cost-effective digital-input solution while retaining closed-loop speaker-current feedback. The TAS5805M integrates a 96 kHz signal-processing architecture with sample-rate conversion, 15 biquads per channel, volume control, audio mixing, three-band fourth-order dynamic range control, full-band automatic gain limiting, and THD management. This combination supports speaker protection, level control, and source-specific tuning without requiring a separate digital-audio processor for every basic function. The device supports stereo or mono operation and can deliver up to 23 W per stereo channel under the conditions specified by Texas Instruments. Its 4.5 V to 26.4 V supply range accommodates portable, industrial, and consumer audio systems. The manufacturer describes the design as inductor-less, allowing the external speaker interface to use a conventional LC filter rather than requiring an output inductor. Typical uses include soundbars, smart speakers, television and monitor audio, compact consumer systems, and other digital-input audio products. The 96 kHz processing architecture is particularly relevant when the design needs advanced level management and speaker protection close to the power stage. Digital control data is handled through the device's serial audio and control interface. A critical layout requirement is keeping the Class-D switching node compact and isolated from sensitive input and control traces. Follow the manufacturer datasheet's power, ground, decoupling, and filter-layout guidance because high dV/dt switching edges can create EMI coupling and ground bounce. The exposed thermal pad also requires careful thermal design when the amplifier operates near its maximum output power. This product page combines the exact ordering information, verified manufacturer and distributor resources, strict drop-in assessment, application guidance, and design-focused comparisons. It helps engineers determine whether the TAS5805MPWP fits a digital-input speaker design before committing to a PCB or firmware configuration.
TAS5827 - 47W Stereo Closed-Loop Class-D Amp | TI
The TAS5827 is a stereo high-performance, closed-loop Class-D audio amplifier with an integrated audio processor and support for up to 192-kHz audio. It delivers 47W per channel in BTL mode and is housed in a 32-pin VQFN (5x5 mm) package. The device features a digital input interface, making it ideal for modern digital audio systems. A Class-D amplifier is a switching amplifier that uses pulse-width modulation to achieve high efficiency, often exceeding 90%, compared to linear amplifiers. It is a key component in the audio signal chain, converting digital audio data into high-power analog output while minimizing heat dissipation. The TAS5827 integrates a closed-loop architecture, which improves linearity and reduces distortion, and an audio processor for advanced signal processing. Key features include a delay buffer up to 5ms in BTL mode or 10ms in PBTL mode, Class-H control for enhanced efficiency, and hardware control mode for selecting switching frequency, analog gain, BTL/PBTL mode, and cycle-by-cycle current limit threshold via pin configuration. The device also supports software control mode with classic BQs, 3-band DRC, AGL, and proprietary audio envelope tracking Class-H control. The TAS5827 uses a closed-loop feedback design that reduces power supply noise and improves audio quality. It integrates a high-performance audio processor capable of executing complex DSP algorithms, making it suitable for applications requiring EQ, DRC, and dynamic range compression. The device operates from a single supply and includes comprehensive protection features. Typical applications include smart speakers, soundbars, home theater systems, and active speakers. Its high efficiency and low power dissipation make it ideal for battery-powered and energy-conscious designs. The integrated audio processor reduces external component count, simplifying system design. When designing with the TAS5827, ensure proper PCB layout for thermal management and minimize parasitic inductance in the output stage. Use appropriate decoupling capacitors on the power supply pins and follow the recommended layout in the datasheet for optimal performance.
TAS5827RHBR - 43W Stereo Digital Class-D Amp | Texas Instruments
The Texas Instruments TAS5827RHBR is a 43-W stereo, digital-input, closed-loop Class-D audio amplifier with integrated audio processing and Class-H control. Housed in a 32-pin VQFN (RHB) package measuring 5x5 mm, this device delivers high-efficiency amplification for a wide range of consumer and professional audio applications. It supports a supply voltage range of 4.5V to 26.4V and operates over a temperature range of -40°C to 85°C. A Class-D amplifier is a switching amplifier that uses pulse-width modulation (PWM) to achieve high efficiency, often exceeding 90%, compared to linear amplifiers. The TAS5827 integrates a closed-loop architecture that reduces distortion and improves power supply rejection, making it suitable for high-fidelity audio systems. The digital input interface accepts I2S, TDM, and other digital audio formats, simplifying system design by eliminating the need for external DACs. Key features include a 43-W output power per channel into 4-ohm loads, integrated audio processor with biquad filters and dynamic range compression, and Class-H control that optimizes power supply voltage for efficiency. The device also supports multiple switching frequencies and offers cycle-by-cycle current limit protection. Its closed-loop design ensures low THD+N and high signal-to-noise ratio, critical for premium audio performance. The TAS5827 uses a digital audio processing core that can be configured via I2C or hardware control mode. In hardware mode, switching frequency, analog gain, BTL/PBTL mode, and current limit threshold are set via pins, eliminating the need for software driver integration. This flexibility makes it easy to deploy in systems where firmware development is not desired. Typical applications include smart speakers, soundbars, home theater systems, and automotive audio. The high efficiency reduces heat dissipation, enabling compact designs without large heatsinks. The integrated audio processor allows designers to implement EQ, crossover, and dynamic range control without external DSP. When designing with this device, ensure proper PCB layout with adequate ground planes and decoupling capacitors near the power pins. The thermal pad must be soldered to a copper area for heat dissipation. Also, consider the input signal format and configure the device accordingly for optimal performance.
TAS6754QDKQRQ1 - Automotive 4-Ch Class-D Audio Amp | TI
The TAS6754QDKQRQ1 is an automotive-grade, four-channel digital-input Class-D audio amplifier from Texas Instruments, offered in a 56-pin HSSOP (DKQ) package with exposed thermal pad. It implements 1L modulation, requiring only one inductor per BTL channel, and operates from a 19V supply with a 2MHz switching frequency. The device integrates current sense and real-time DC/AC load diagnostics for robust automotive speaker fault detection. A Class-D audio amplifier is a switching amplifier that converts a digital or analog audio signal into a high-frequency pulse-width modulated square wave, which is then low-pass filtered to reconstruct the audio. Class-D topologies achieve high efficiency (typically 80-90%) because the output transistors operate as switches, minimizing power dissipation compared to linear Class-AB amplifiers. In automotive audio systems, this efficiency reduces heat-sinking requirements and extends the available audio power from the vehicle's electrical system. Key features include four independent audio channels, 1L modulation that removes four inductors versus traditional designs, 2MHz switching for compact output filters, integrated current sense, and DC/AC real-time load diagnostics. The 19V rated supply is aligned with automotive audio power rails, and the AEC-Q100 Q1 suffix qualifies the device for automotive applications. The 56-pin HSSOP package supports surface-mount assembly with an exposed thermal pad for heat removal. 1L modulation is a proprietary Class-D scheme that uses a single inductor per bridge-tied-load channel, reducing system cost and size. The 2MHz switching rate moves the switching fundamental well above the audio band, simplifying the output low-pass filter and lowering out-of-band emissions. Integrated current sense and real-time load diagnostics monitor speaker health, enabling fault detection for shorts, opens, and degradation. The digital input accepts common automotive digital audio formats, eliminating the need for a separate DAC and analog front end. Typical applications include automotive infotainment head units, external amplifier modules, EV pedestrian warning (AVAS), telematics/eCall audio, rear-seat entertainment, and commercial-vehicle audio. The device is especially suited for designs where four channels of clean audio must be delivered from a 19V rail with minimal inductor count and integrated diagnostic coverage. When designing with the TAS6754QDKQRQ1, provide sufficient copper area on the exposed thermal pad and keep the output LC filter close to the device to minimize EMI. Verify the digital audio source timing and protocol against the datasheet before PCB layout.
TCA0372BDP1 - 1A Dual Power Op Amp 5-40V | onsemi
The onsemi TCA0372BDP1 is a dual power operational amplifier with two independent amplifier channels, a 5 V to 40 V supply range, and output-current capability up to 1 A per channel. The device is packaged in an 8-pin plastic dual in-line package designated 8-PDIP and is intended for power stages driving loads that exceed the current range of conventional operational amplifiers. A power operational amplifier is an operational amplifier integrated with output-driver circuitry capable of supplying substantially higher load current. The TCA0372 family occupies the power-amplifier segment of the operational-amplifier hierarchy and is commonly positioned between general-purpose signal amplifiers and discrete transistor output stages. Its dual-channel architecture allows one package to drive two independent loads or to provide a complementary output arrangement when configured appropriately. The main feature is high output-current capability of 1.0 A, allowing the amplifier to drive inductive, resistive, and capacitive loads more effectively than a conventional small-signal op amp. The 5 V to 40 V operating supply range supports higher-voltage systems than many low-voltage integrated amplifiers. According to the onsemi product page and manufacturer datasheet, the circuit is intended for servo amplifiers and power supplies, with no deadband crossover distortion intended to improve operation when driving coils. Each channel contains an error amplifier followed by high-current output capability, allowing feedback to control the voltage delivered to the load. The power bipolar output stage can sink and source current, while external resistors and capacitors establish gain, bandwidth, stability, and output bias in the completed circuit. The high current capability does not remove the need to observe output-stage limits, load transients, supply decoupling, thermal conditions, and output-voltage headroom. Typical uses include DC servo amplifiers, power-supply error amplifiers, audio and motor-control power stages, and industrial actuator drivers. The dual configuration can reduce component count in mirrored or dual-axis systems. For single-channel designs, one channel may remain unused, subject to the manufacturer's recommended input and output termination arrangements. PCB layout should keep feedback routing short and place supply-bypass capacitors close to the device. Because output current can reach 1 A, copper width, connector sizing, thermal dissipation, and load-return paths become important. Designers should also use protection or snubber networks when switching highly reactive loads because feedback alone cannot absorb unlimited inductive energy. This product page consolidates the confirmed electrical ratings, package information, sourcing structure, drop-in candidates, and application guidance for TCA0372BDP1. It also identifies which comparison details require verification against the manufacturer datasheet, helping engineers plan a controlled redesign and validation process rather than relying only on a generic amplifier substitution.
TCA0372DP1 - 1A Dual Power Operational Amplifier | onsemi
onsemi TCA0372DP1 is a dual-channel power operational amplifier intended for high-current amplifier stages, servo amplifiers, power supplies, and inductive loads. The device operates from a 5 V to 40 V supply range, provides output current up to 1.0 A, and uses a 1.4 MHz gain-bandwidth product. It is packaged in an 8-pin PDIP. Its monolithic power-output stage is designed to reduce crossover distortion when driving coils, making the TCA0372DP1 useful in systems where conventional small-signal operational amplifiers cannot deliver adequate load current. A power operational amplifier is an operational amplifier integrated with an output stage capable of supplying substantially more current than a conventional precision amplifier. This places the device within the hierarchy of operational amplifier, linear amplifier, analog signal amplifier, and integrated circuit. Unlike a switching regulator, the TCA0372DP1 amplifies an analog error or control signal while maintaining continuous conduction. Its power-output capability allows one dual amplifier package to serve both error amplification and high-current drive functions in feedback-controlled systems. The primary headline characteristics are a 1.0 A maximum output current, a 5 V to 40 V operating supply range, and a 1.4 MHz gain-bandwidth product. The dual configuration provides two amplifier channels in one package, reducing board area in multi-axis servo or dual-channel drive systems. The lack of dead-band crossover distortion is particularly relevant when driving inductive coils because it avoids the command dead zone commonly introduced by power-output stages that switch between positive and negative drive states. The TCA0372 is a monolithic circuit, allowing its internal drive and amplifier sections to share a common package and support direct analog feedback-control operation. In a typical servo amplifier, an external position or speed loop generates a command voltage, and the TCA0372 channel amplifies that command into a motor-drive signal. Feedback from the actuator closes the loop. The wide operating-voltage range also permits use with higher-voltage power systems when the remaining input, output, and thermal requirements are satisfied. Typical uses include servo-amplifier output stages, closed-loop motor controllers, industrial actuator drivers, power-supply error amplifiers, and other systems that require analog feedback with a high-current output. For AC or bipolar drive arrangements, the external network must handle the required current and voltage excursions without exceeding the device's electrical limits. Heat management and output-stage stability are important when continuous load operation approaches the output-current rating. Circuit implementation should preserve the feedback connection at the amplifier output and minimize PCB-trace resistance between the power-output pins and the load. Input and output decoupling should follow the manufacturer's recommended application circuit. Because the amplifier dissipates power internally, designers should calculate worst-case output dissipation, provide adequate copper area, and verify that the ambient temperature and load waveform keep junction temperature within the qualified operating range. This product page combines the exact TCA0372DP1 electrical and package identifiers with datasheet references, application guidance, and a package-aware comparison. It also distinguishes documented functions from parameters requiring confirmation in the manufacturer datasheet. The result is a practical engineering reference for evaluating whether this dual, high-current operational amplifier matches a servo, power-supply, or inductive-drive design without confusing it with a switching power converter.
TCA0372DP1G - 1A Dual Power Op Amp | onsemi
The onsemi TCA0372DP1G is a dual monolithic power operational amplifier capable of delivering 1.0 A output current from a 5 V to 40 V supply in an 8-pin PDIP package. The device provides two power operational-amplifier channels, a unity-gain bandwidth of 1.4 MHz, a nominal common-mode rejection ratio of 90 dB, and an input offset voltage as high as 20 mV. Its extended-temperature grade supports applications beyond the standard commercial temperature range. A power operational amplifier is a voltage-controlled amplifier that combines the high input impedance and closed-loop control of an ordinary operational amplifier with substantially greater output-current capability. Within the power-management and signal-chain hierarchy, the TCA0372 belongs to the amplifier IC family and is commonly used where a low-level error or control signal must directly drive a coil, motor winding, speaker, or power-supply output stage. The TCA0372's 1.0 A output-current capability makes it suitable for servo amplifiers, regulated power supplies, and industrial actuator drivers. Its no-dead-band crossover-distortion characteristic improves drive into inductive coils compared with solutions exhibiting an output transition dead zone. The two independent channels also permit mirrored, complementary, or dual-axis motion-control architectures while preserving identical amplifier characteristics. The monolithic dual-amplifier design simplifies system implementation by placing two power op-amp channels in one package. The 1.4 MHz unity-gain bandwidth supports applications that require both low-frequency loop control and useful bandwidth for dynamic feedback systems. The 90 dB nominal common-mode rejection ratio helps isolate the input stage from common-mode disturbances, while the 20 mV maximum input offset voltage defines the practical DC error boundary that must be considered in precision servo loops. Typical uses include servo-motor control, audio output stages, power-supply regulation, industrial positioning systems, and actuator drivers. Two amplifiers in one PDIP package can reduce board area when a system requires dual-axis control or complementary drive. Where the load is inductive, flyback current must be controlled with an external clamp path, and where the load is capacitive, stability must be checked using the feedback network and load conditions. The primary design tradeoff is sustained output-current capability versus heat generated inside the 8-pin PDIP package. A 1.0 A rating does not imply that every load condition can be driven continuously without thermal analysis. Verify copper area, ambient temperature, output duty cycle, voltage headroom, and required safety margin before using the full current rating. Follow the onsemi datasheet for recommended compensation, bias-pin bypass, and application-circuit details. This page organizes the key electrical limits, application guidance, drop-in candidates, and package-level design considerations for engineers evaluating the TCA0372DP1G in dual power-amplifier systems.
TCA0372DP2 - 1A Dual Power Op Amp | onsemi
onsemi TCA0372DP2 is a dual power operational amplifier delivering up to 1.0 A output current and operating from a 5 V to 40 V supply in an 8-pin PDIP package. The monolithic device is designed for servo amplifiers, power supplies, and inductive loads, with no deadband crossover distortion to improve coil-drive performance. A power operational amplifier is a high-current linear amplifier that combines the gain and signal handling of a conventional operational amplifier with the ability to source or sink substantial load current. Within the amplifier hierarchy, it belongs to the power-amplifier class rather than the general-purpose low-current op-amp category. Its practical role is to turn a low-level control signal into a high-current drive for motors, solenoids, and other demanding loads. The TCA0372 family provides two independent amplifier channels, 1.0 A output-current capability per power-amplifier stage, and a 5 V to 40 V operating range. The absence of deadband crossover distortion is particularly useful when driving coils because the output crosses through zero more linearly than a conventional output stage with a dead region. This characteristic can reduce drive dead zone in bidirectional servo and actuator systems. The monolithic power-amplifier architecture supports relatively demanding loads without requiring a separate external power-transistor stage. Because the device combines amplification and current delivery in one package, the surrounding design must still account for supply decoupling, output-current limits, thermal dissipation, and protection against inductive voltage spikes. Its wide 40 V maximum supply rating provides useful headroom for industrial and automotive-style actuator systems. Typical applications include servo-amplifier loops, power-supply control stages, relay and solenoid drivers, motor-control systems, and other inductive or high-current loads. The dual-channel configuration can also support two coordinated actuator channels or one control function plus a complementary auxiliary function, subject to the applicable electrical and thermal limits. For a new design, preserve adequate supply decoupling near the device, verify the continuous and peak current requirements of the connected load, and provide suitable flyback protection for inductive loads. The through-hole PDIP package is straightforward for prototype and legacy industrial assemblies, although a surface-mount power-amplifier option may be preferable for compact production hardware. This product overview combines the confirmed 1.0 A current, 5 V to 40 V supply range, dual-channel architecture, no-deadband feature, and PDIP-8 format with practical guidance for amplifier selection, PCB implementation, thermal review, and drop-in replacement assessment.
TCA0372DP2G - Dual 1A Power Op Amp | onsemi
The onsemi TCA0372DP2G is a dual power operational amplifier rated for a 1.0 A output current and a 5 V to 40 V supply range in a 16-pin PDIP package. Its two amplifier channels are designed for power-level signal conditioning, including servo amplifiers, power supplies, and inductive loads. The manufacturer identifies the TCA0372 family as a monolithic dual power operational amplifier with no deadband crossover distortion. A power operational amplifier is an integrated circuit that combines the voltage gain of an operational amplifier with the drive capability of a power output stage. This places the component in the amplifier IC hierarchy between precision signal amplifiers and discrete power-transistor stages. Its purpose is to amplify a low-level control signal while providing enough output current to drive loads that a conventional small-signal operational amplifier cannot handle directly. The most important device-level specifications are the 1.0 A output-current capability, 5 V to 40 V operating supply range, 1.4 MHz bandwidth indication, and dual-channel configuration. The extended-temperature marking distinguishes this exact ordering code from catalog entries with narrower environmental coverage. Its power-output topology is particularly relevant when driving coils, motors, solenoids, or other loads where the output must remain linear across positive and negative signal excursions. The two channels share the same monolithic power-amplifier architecture and are intended for applications requiring substantial output current without the discrete driver circuitry normally associated with power stages. Eliminating deadband crossover distortion can simplify feedback-loop design in bipolar or bidirectional drive systems because the output follows the command signal more directly around zero. Engineers should nevertheless account for supply headroom, output-current limits, load return paths, and the thermal load created during sustained high-current operation. Typical uses include servo-amplifier control loops, regulated power-supply error amplifiers, motor and solenoid drivers, audio amplification, and industrial actuator interfaces. The 16-pin PDIP format favors through-hole construction and repairable assemblies. The same package can also support prototype and legacy-system maintenance where a high-current output stage must fit an existing dual-in-line board layout. A robust design should use low-inductance supply and ground connections, place input and feedback components close to the relevant pins, and provide adequate copper and thermal dissipation around the output path. Feedback compensation and stability must be evaluated with the actual load impedance and cable capacitance. Current limiting or protection may also be required when the load can exceed the device's 1.0 A rating or develop an abrupt fault condition. This product page combines the manufacturer datasheet, distributor catalog information, package details, lifecycle context, application guidance, and drop-in-replacement analysis. It is designed to support component selection, PCB planning, sourcing, and design review for engineers working with high-current dual power operational amplifiers.
TCA0372DW - Dual 1A Power Op Amp | onsemi | 16-SOIC
onsemi TCA0372DW is a dual power operational amplifier with 1.0 A output current, a 5 V to 40 V operating range, and a 16-lead SOIC package. The device is intended to amplify low-level error signals directly into high-current loads without adding a separate power-output stage. Its dual-circuit configuration allows two independent power-amplifier channels within one package, reducing board area in multi-axis motion, audio, and power-control systems. A power operational amplifier is a specialized operational amplifier that combines high-voltage signal handling, low-voltage input amplification, and current-drive capability. Within the product hierarchy, it belongs to the operational-amplifier family, amplifier IC family, analog signal-conditioning category, and broader semiconductor category. Unlike a conventional small-signal operational amplifier, the TCA0372 is designed to drive coils, motors, and other loads that require substantially more output current than a standard op amp can supply. The principal verified features include 1.0 A output current, dual power-amplifier operation, a 5 V to 40 V supply range, and operation without deadband crossover distortion. The absence of deadband crossover distortion is especially relevant when the amplifier drives coils because it avoids the output transition region that can introduce nonlinear behavior around zero. According to the onsemi manufacturer datasheet, the monolithic circuit is intended for power supplies and servo amplifiers as well as coil-driving applications. The TCA0372 integrates input amplification and power-output capability in one monolithic device, reducing the number of external drive stages required in a power-control design. Two amplifiers are provided in the package, allowing a dual-axis actuator system or two independent power channels to share one 16-SOIC package. Its wide 5 V to 40 V operating range supports applications operating from conventional industrial rails through higher-voltage motor-control systems. Typical uses include DC servo amplifiers, closed-loop position and speed control, audio power stages, industrial actuator drivers, and power-supply error amplifiers. In a servo loop, the TCA0372 can convert a low-level feedback error into a high-current motor command. For audio, its dual-channel organization can support left and right channels when the load and thermal conditions permit. In power supplies, its output current and high-voltage capability can drive suitable external stages when the required operating point remains within the datasheet limits. Designers should verify the complete electrical characteristics, pin connections, thermal limits, and output-stage behavior in the onsemi datasheet before layout. Decoupling must minimize output-stage transients and supply noise, while PCB copper and thermal design must accommodate dissipation during sustained high-current operation. The 16-pin SOIC footprint also requires adequate spacing from heat-generating components because its relatively small lead frame can limit heat dissipation. This product record combines verified manufacturer and distributor information, same-family replacement analysis, parameter-level comparison, and practical engineering guidance. It distinguishes confirmed TCA0372DW facts from specification fields that were not supplied in the retrieved data, helping engineers make evidence-based sourcing and design decisions.
TCA0372DWG - 1A Dual Power Op Amp | onsemi | 16-SOIC
The onsemi TCA0372DWG is a dual power operational amplifier with 1.0 A output current, a 5 V to 40 V operating supply range, and a 16-pin SOIC package. Designed for power-buffer, servo-amplifier, power-supply, and coil-driving applications, the device combines two amplifiers in one package while supporting output currents of 1.0 A. A power operational amplifier is a high-current amplifier that sits between a low-power control signal and a load such as a motor, solenoid, actuator, or power-conversion stage. It belongs to the operational-amplifier hierarchy, amplifier family, and broader analog and power-management semiconductor categories. Unlike a conventional low-current signal op amp, a power op amp is intended to provide substantially greater load-driving capability while preserving closed-loop control of voltage or current. Key characteristics of the TCA0372DWG include 1.0 A output current, a 1.4 MHz gain-bandwidth product, and a 1.3 V/µs slew rate. Its operating supply range extends from 5 V to 40 V, making it appropriate for industrial, audio, servo, and power-control systems that operate above conventional ±15 V laboratory supply levels. The device also uses a no-deadband output architecture, which improves behavior when driving inductive coils. The TCA0372 is a monolithic dual circuit, allowing independent use of the two amplifier sections when their supply and thermal requirements permit. Its 1.4 MHz bandwidth supports applications requiring more bandwidth than a slow power-buffer stage while its 1.3 V/µs slew rate provides comparatively fast voltage transitions. These characteristics make it suitable for audio power stages, servo loops, motor-control paths, and power-supply control loops. Typical applications include servo amplifiers, regulated power supplies, audio amplifiers, motor drivers, actuator controllers, and coil drivers. The 1.0 A output capability is important when the load draws substantially more current than a standard precision op amp can deliver. Designers should still evaluate the SOA limits, supply capability, output saturation, load impedance, and thermal dissipation for the exact operating conditions. For reliable layout, keep feedback and compensation components close to the amplifier pins, provide robust supply decoupling, and use a PCB copper area that can remove heat generated at high output current. Avoid driving the output into excessive capacitive loads, and include current limiting or protection where the connected coil or actuator can present an unusual startup transient. This product data consolidates the manufacturer specifications, package information, sourcing details, same-family alternatives, comparison parameters, and practical design guidance into an engineering-oriented reference for selecting and implementing the TCA0372DWG.
TCA0372DWR2 - Dual Power Op-Amp 1A SOIC-16 | onsemi
The onsemi TCA0372DWR2 is a dual power operational amplifier delivering up to 1.0 A output current per channel, operating from supply rails of 5 V to 40 V (or ±20 V dual supply), housed in a 16-pin wide SOIC (SOIC-16 W, DW suffix) surface-mount package. A power operational amplifier is an op-amp that combines the precision input stage and high open-loop gain of a standard operational amplifier with an output stage capable of sourcing or sinking currents in the ampere range, far beyond the tens of milliamps typical of general-purpose op-amps. In the power-management and signal-chain hierarchy, the TCA0372 sits between standard op-amps and fully integrated audio or motor driver ICs: it is an amplifier - specifically a power op-amp - classified under operational amplifiers / buffer amplifiers in vendor taxonomies. Key differentiating features of the TCA0372 include the 1.0 A continuous output current rating, a gain-bandwidth product around 1.4 MHz with a 1.4 V/us slew rate, and operation on a single supply from 5 V to 40 V or on dual supplies up to ±20 V. The device is internally compensated and, critically, exhibits no deadband crossover distortion in the output stage, which is essential when driving inductive loads such as coils, actuators, and servo motors where crossover artifacts translate directly into torque ripple or audible distortion. Architecturally, the TCA0372 is a monolithic bipolar device integrating two complete power op-amp channels on a single die. The wide-body SOIC-16 package provides substantially better thermal dissipation than a standard SOIC-8, allowing both channels to drive heavy loads when adequate PCB copper is provided. Internal thermal limiting and safe-area considerations typical of power output stages protect the device during faults, though board-level thermal design remains the designer's responsibility at sustained high current. Typical applications include servo amplifiers for position control, power supplies as error amplifiers or pass-element drivers, coil and solenoid drivers, motor control subcircuits, audio power output stages, and general power buffering where a standard op-amp cannot supply the required load current. When designing with the TCA0372, account for package power dissipation: at 1 A output across a large input-to-output voltage differential, junction temperature rise is dominated by the SOIC-16 thermal resistance, so generous copper pours on the output-stage pins are recommended. This page adds value beyond the manufacturer datasheet by consolidating drop-in replacement options (TCA0372DWR2G, TCA0372BDWR2G, NCV0372B variants), application guidance, and comparison data in one place for sourcing and design engineers.
TCA965B - Window Comparator, 4.5-30 V, 14-DIP | Infineon
The Infineon Technologies TCA965B is a bipolar window discriminator with two adjustable window settings, adjustable hysteresis, and two open-collector digital outputs rated for 50 mA. Its verified supply range is 4.5 V to 30 V, and the specified commercial package is the 14-pin PG-DIP-14-1 through-hole package. The device indicates whether an input voltage is below, inside, or above a defined comparison window. A window comparator is a specialized comparator integrated within the broader voltage-comparator and analog-interface hierarchy. Instead of providing only one switching threshold, it evaluates an input against two limits and reports when that input lies outside the acceptable band. This makes the TCA965B useful for voltage supervision, tracking control, dead-band control, and DC-voltage selection tasks identified in the manufacturer documentation. The window edges can be configured directly, or the window can be established indirectly from its center voltage and half-width. Adjustable hysteresis reduces output chatter when the monitored voltage changes near an edge, while an adjustable reference supports threshold calibration. The open-collector outputs permit wired logic, relay interfaces, and pulled-up buses, but external pull-up resistors and suitable sink-current limits are required. The bipolar implementation supports operation from 4.5 V through 30 V, making the TCA965B appropriate for industrial control systems operating above conventional low-voltage logic rails. Because its outputs are open collector, the device can interface with systems whose logic supply differs from the comparator supply. Designers must account for output rise time, pull-up resistance, load capacitance, and the common-emitter arrangement when wiring the outputs. Typical uses include power-supply sequencing, battery-voltage qualification, tracking power controllers, process-control dead-band monitors, and DC-voltage selection within an allowed tolerance. In each circuit, the two window references determine acceptance limits while the digital outputs report undervoltage, in-window, and overvoltage conditions. The principal tradeoff is that the legacy 14-DIP package is larger than modern surface-mount alternatives, but it supports straightforward prototyping and through-hole assembly. When designing around the TCA965B, begin with the verified supply requirement, configure the reference and window network using the manufacturer guidance, and confirm every output pull-up voltage. Do not assume logic-level compatibility from the 30 V supply capability because the open-collector pins do not actively drive a high output. Check hysteresis against noise and load-transient requirements, then validate the complete threshold system across temperature and supply variation. This page combines the verified manufacturer and distributor records with package, application, comparison, and design guidance. It also distinguishes verified facts from unavailable electrical details rather than estimating unstated thresholds, propagation delays, package dimensions, or prices.
TDA18214AHN/C1,557 - Silicon TV Tuner IC DVB-T | NXP
The NXP Semiconductors TDA18214AHN/C1,557 is a high-performance silicon tuner IC designed for digital terrestrial and digital cable TV reception, controlled via an I2C serial interface and housed in a 40-pin HVQFN (6x6 mm) exposed-pad package. The part delivers a Low IF (LIF) output signal to an external demodulator and supports all major digital TV standards including DVB-T. A silicon tuner is an integrated RF receiver front-end that replaces the can-tuned varactor modules used in legacy analog televisions. Within the receiver signal chain hierarchy, it sits at the top: antenna or cable input -> silicon tuner (RF amplification, image-reject mixing, channel filtering) -> Low IF output -> demodulator IC -> transport stream. Because tuning, gain control, and filtering are all implemented on-chip, the TDA18214 family dramatically reduces board area, BOM count, and factory alignment effort compared with discrete tuner designs. Key features of the TDA18214AHN include single-conversion architecture delivering a Low IF signal, full I2C bus control for channel selection and gain programming, support for all digital terrestrial and cable TV standards (DVB-T, DVB-C, ISDB-T, ATSC, DTMB families), and an exposed-pad 40-HVQFN package suitable for compact set-top box and TV main boards. Surface-mount construction supports standard reflow assembly. Architecturally, the TDA18214 integrates a low-noise RF amplifier, image-reject downconversion mixer, broadband synthesizer, and channel-selection filtering in a single CMOS/BiCMOS die. Delivering LIF directly to the demodulator eliminates SAW-filter-heavy IF stages in many designs, and the digital-controlled gain distribution optimizes linearity versus noise figure across the received channel. Typical applications include digital set-top boxes, integrated digital TV (iDTV) main boards, USB TV tuner dongles, PC-TV capture cards, and cable/terrestrial hybrid receivers. Its broad standards support lets one design serve multiple regional markets with firmware changes only. Design consideration: as a 6x6 mm HVQFN with exposed pad, the thermal and ground path depends on the PCB land pattern; the exposed pad must be soldered to a solid ground plane with thermal vias, and the I2C bus requires proper pull-up sizing for reliable 100/400 kHz communication. This page synthesizes distributor availability data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Note that this part is marked Obsolete (last buy March 31, 2016; last delivery June 30, 2016), so availability is limited to remaining distributor and broker stock as of 2026-10-11.
TDA2009A - 10W+10W Stereo Class-AB Audio Amplifier | STMicroelectronics
The STMicroelectronics TDA2009A is a class-AB dual Hi-Fi audio power amplifier assembled in a Multiwatt® package, delivering 10 W + 10 W of continuous output power per channel into 8 Ω loads (stereo operation from 8 V to 28 V supply). The device is specially designed for high quality stereo applications such as Hi-Fi music centers, mini-component stereos, multimedia speaker systems, and instrument amplifiers that demand dual-channel output from a single, well-protected IC. What is a class-AB audio power amplifier? A class-AB amplifier is the most common bipolar topology used in mid-power audio reproduction; it biases its output stage so that push and pull transistors each conduct for slightly more than half a cycle. This eliminates the crossover distortion of pure class-B designs while keeping efficiency far higher than class-A. The TDA2009A instantiates that topology with on-chip short-circuit protection, thermal shutdown, and AC short-circuit protection of the load, integrating a complete stereo driver into one Multiwatt-11 power package with the heatsink tab on the back. Key features include 10 W + 10 W continuous output into 4 Ω with THD = 10 % at 14 V / 4 Ω (per ST datasheet), 1 % THD typical at lower levels, an operating supply range of 8 V to 28 V, 3 A peak output current per channel, very low harmonic and crossover distortion, and internal protection against short circuits, thermal overload, and DC voltage on the load. The Multiwatt-11 (Pentawatt-style) package exposes a metal tab so the part itself forms the heatsink, simplifying PCB mechanical design. The architecture uses a vertical bipolar power process with quasi-complementary NPN/PNP output pairs, a unity-gain inverting topology per channel, and internal bias generators that minimize quiescent crossover glitch. The result is a flat frequency response from 20 Hz to 20 kHz with low 0.1 % harmonic content, suitable for full-range music reproduction without complex external compensation networks. Typical applications include stereo Hi-Fi music centers, multimedia speaker systems, TV audio output stages, guitar and instrument practice amplifiers, automotive radios (with 14 V supply), and self-powered USB speakers where dual-channel audio from a single chip replaces two single-channel modules. When designing with this device, place a 100 nF decoupling capacitor on the supply pin as close as possible to the IC, use feedback resistors of 39 kΩ for closed-loop gain near 35 dB, and provide adequate heatsinking through a clip-on or bonded tab. The package tab is electrically tied to the -Vs pin (or to the substrate in some legacy datasheets) - consult the datasheet pinout before insulating the heatsink. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes for the TDA2009A, providing information not consolidated on any single distributor product page.
TDA7297 - 15W+15W Dual Bridge Amplifier | STMicroelectronics
The STMicroelectronics TDA7297 is a dual bridge Class-AB audio amplifier delivering 15W+15W output power in a 15-pin Multiwatt package, designed specifically for TV and portable radio applications. It operates from a wide 6V to 18V supply range and uses an internally fixed gain topology that eliminates the need for SWR capacitors, bootstrap networks, and Boucherot cells. A Class-AB (dual bridge) audio amplifier is a topology that combines two push-pull output stages in a bridge-tied-load (BTL) configuration, allowing higher output swing across a speaker load without large DC-blocking capacitors. The TDA7297 belongs to the broader category of integrated audio power amplifiers, which sit within the analog signal chain and power management domains in a typical consumer electronics design. Dual-bridge configurations are especially valued in compact consumer devices because they double the voltage swing across the speaker and remove the need for a bulky output coupling capacitor. Key features include 15W per channel continuous output into 8 ohm loads, low standby current with a dedicated Standby pin, and a Mute function for click-free power-up sequencing. The device integrates all output transistors in the same silicon die and requires only a few external resistors and a power supply bypass network, enabling very compact PCB designs. Typical THD at 1W output is in the 0.1%-0.5% range, making it suitable for entry-level TV audio, multimedia monitors, and portable boombox designs. The internally fixed gain topology simplifies board layout but limits design flexibility compared to externally adjustable amplifiers like the TDA7294. Thermal performance is handled through the Multiwatt-15 package, which exposes the die tab to a vertical heatsink profile with through-hole pins for robust mechanical mounting. Designers must still respect the safe operating area at high ambient temperatures where sustained 2x15W output can push the junction close to thermal limits without adequate heatsinking. Typical applications include flat-panel TV stereo speaker drivers, portable radio boombox amplifiers, LCD monitor audio outputs, PC motherboard sound subsystems, and DIY audio upgrade kits. The part is commonly found in 2.1-channel subwoofer + satellite systems where a third mono channel can be derived by bridging the two outputs in parallel. When designing with the TDA7297, always provide adequate heatsinking through the Multiwatt tab and respect the 6V-18V supply range. The Standby and Mute pins should be sequenced with a 10kohm/10uF RC network as recommended in the datasheet to achieve click-free power transitions.
TDA7379 - 4x13W / 2x38W Class-AB Quad Audio Power Amplifier | STMicroelectronics
The STMicroelectronics TDA7379 is a Class-AB audio power amplifier capable of 4x13W or 2x38W output, housed in a Multiwatt-15 package and intended for car-radio and high-power consumer audio applications. The device operates from an 18V nominal supply (operating up to 28V) and integrates a fixed 26dB BTL gain stage that eliminates the need for external bootstrap capacitors, Boucherot cells, or feedback networks. An additional feature is the CMOS-compatible standby function that drops quiescent consumption during mute conditions. A Class-AB amplifier is a linear audio power amplifier in which the output transistors are biased into partial conduction, reducing crossover distortion compared to pure Class-B while achieving higher efficiency than Class-A. Within the broader taxonomy, the TDA7379 belongs to the linear power amplifier family, sitting under the audio power amplifier category, which in turn is part of the signal-chain / amplifier IC family. This hierarchy matters because system designers typically select a Class-AB part like the TDA7379 for high-output, low-noise single-supply audio stages where switch-mode solutions would inject unacceptable EMI into the signal path. Key features of the TDA7379 include a minimum external component count (no bootstrap capacitors, no Boucherot cells), internally fixed 26dB BTL gain, a high output power capability (4x13W into 4 ohm in quad single-ended mode or 2x38W into 4 ohm in dual BTL mode), CMOS-compatible standby, short-circuit protection to ground and to VCC, load-dump voltage surge protection, and reversed-battery protection. These features make the part particularly suited to automotive environments where transient voltages and wiring faults are common. The amplifier's quad single-ended / dual BTL topology allows system designers to choose between four channels of moderate-power audio (for a front/rear speaker pair system) or two channels of high-power audio (for a subwoofer or stereo bridge-tied load). Internally fixed gain simplifies design and reduces variability across production boards; the trade-off is that the gain cannot be trimmed externally. Typical applications include car-radio amplifiers, multi-channel automotive head units, active speaker systems, subwoofer amplifiers, public-address (PA) amplifiers, and replacement boards for legacy automotive audio equipment. The Multiwatt-15 through-hole package also makes it a strong candidate for repair and refurbishment of older car-audio head units where the original amplifier IC has failed. When designing with the TDA7379, engineers should keep the supply rails well bypassed (100 nF + 1000 uF minimum) and provide a generous ground plane, as high peak currents flow through the output stage. Output short-circuit detection must be respected - sustained shorts will trigger internal protection, but the design must still ensure the load cannot fault the supply. This page synthesizes distributor pricing, verified drop-in alternatives (same-brand ST TDA family first, then cross-brand equivalents), and practical design notes not found in any single manufacturer datasheet.
TDA8920BTH - 2x100W Class-D Audio Power Amplifier | NXP
The NXP TDA8920BTH is a high-efficiency 2 x 100 W class-D audio power amplifier with very low dissipation, housed in a 24-pin HSOP power package with an exposed thermal pad. It operates over a wide symmetrical supply voltage range of +/-12.5 V to +/-30 V (+/-32 V non-operating) and delivers typical output power of 2 x 100 W into 4 ohm or 8 ohm loads with very low quiescent current. The device can be configured as a single BTL mono channel or as a 2-channel stereo amplifier, and integrates all required analog input, PWM modulator, and gate-drive circuitry for a complete class-D solution. A class-D audio amplifier (also called a switching amplifier) is a type of power amplifier that uses high-frequency pulse-width modulation (PWM) of the audio signal followed by output-stage switching transistors and a low-pass LC reconstruction filter. Compared with classical Class-AB linear amplifiers, class-D topologies achieve dramatically higher efficiency (typically 90%+), far less waste heat, smaller heatsink requirements, and lighter designs, which is why they dominate modern flat-panel TV, soundbar, and portable speaker designs. The TDA8920BTH belongs to the audio amplifier -> power amplifier -> analog IC -> signal chain taxonomy. Key features include differential analog inputs, built-in protection (overcurrent, overtemperature, and undervoltage), selectable BTL/SE mode, mute and standby functions, and an exposed die pad (EP) for direct PCB heatsinking. Its switching frequency is in the typical 350-450 kHz range (data needed for exact figure), enabling use of small output filter inductors and capacitors. The TDA8920BTH uses a self-oscillating or fixed-frequency PWM modulator architecture with feedback after the LC output filter (post-filter feedback), which dramatically reduces distortion and output filter dependency. This topology, combined with NXP's proprietary driver stage, achieves THD figures comparable to high-quality linear amplifiers at a fraction of the power dissipation. Typical applications include home theater and stereo receivers, powered multimedia speakers, subwoofer amplifiers, automotive head-unit booster stages, professional active monitor speakers, and high-end DIY audio builds where 2 x 100 W of clean, efficient power is required in a compact SMD footprint. Its SMD-compatible HSOP24 package also makes it suitable for automated assembly versus the through-hole DBS23P variant (TDA8920BJ). When designing with the TDA8920BTH, pay careful attention to the LC output filter component selection and layout: keep the filter loop area minimal, use low-ESR film or ceramic capacitors, and tie the exposed pad to a large copper pour for thermal management. Always observe the +/-30 V maximum supply rating and include adequate supply decoupling close to the IC pins. This page synthesizes distributor pricing, verified drop-in alternatives (same HSOP24 footprint), practical design notes, and datasheet-based specifications not found on standard distributor listings, giving engineers a complete engineering reference for the TDA8920BTH.
TDF8546TH/N2 - 4x45W BTL Class-AB Car Audio Amplifier | NXP
The NXP TDF8546TH/N2 is an I2C-bus controlled, quad Bridge-Tied Load (BTL) Class-AB automotive audio power amplifier delivering 4 x 45 W into 4 Ω in the 36-pin HSOP (Heatsink Small Outline Package) with exposed thermal pad. It is intended for head-unit and external amplifier applications in 12 V vehicles, with full I2C diagnostics, start-up diagnostics, and best-efficiency switching modes for reduced dissipation during low-to-medium output. What is a quad BTL Class-AB automotive amplifier? A BTL (Bridge-Tied Load) audio amplifier drives each speaker differentially across two outputs, doubling the voltage across the load and quadrupling the achievable output power versus a single-ended topology for a given supply rail. The Class-AB output stage combines bipolar output transistors biased to minimize crossover distortion while preserving high efficiency at moderate output levels, making it the long-standing industry choice for in-vehicle audio. NXP's TDF family falls within the broader power management / amplifier IC hierarchy: Audio Amplifier -> Class-AB Amplifier -> Automotive Audio Amplifier -> Power Management IC -> Semiconductor. Key features of the TDF8546 include operation from a battery supply as low as 6 V (suited to stop/start vehicles), best-efficiency mode that dynamically adjusts output stage biasing, full I2C-bus controlled diagnostics including start-up and runtime load diagnostics, and independent channel gain control. The integrated thermal foldback and over-current protection safeguard the exposed pad / the top-side body of the HSOP package, which is itself the primary heat-dissipation path. The device uses a complementary bipolar output architecture with on-chip gate drivers and charge-pump generation for the high-side NPN transistors, eliminating the need for external bootstrap capacitors. I2C control permits mode switching, mute/unmute, and read-back of diagnostic flags from the host microcontroller, simplifying ECU software development. Typical applications include automotive head units and infotainment amplifiers, external booster amplifiers for premium sound systems, and stop/start-compliant audio platforms where cranking dips below 8 V are common. The combination of best-efficiency operation and low quiescent current helps meet stringent vehicle standby-current budgets. When designing with this part, ensure the HSOP exposed thermal pad is soldered to a copper area of at least 6 cm² for full 4 x 45 W output. Use low-ESR electrolytic bypass capacitors within 10 mm of the supply pins, and keep the I2C lines away from the output traces to avoid coupling. Consider heatsink attachment for sustained high-output operation. This page synthesizes distributor pricing, end-of-life status, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TFA9865 - 7W CoolPWM Smart Class-D Amplifier | Goodix
The Goodix TFA9865 is a high-performance, fully digital Class-D smart audio amplifier delivering 7 W peak output power with an ultra-low noise floor below 7 uV, housed in an extremely compact 2.2x2.2 mm WLCSP package. It targets mobile and portable audio applications where board area, quiescent power, and acoustic clarity are simultaneously critical design constraints. A Class-D audio amplifier is a switching-mode power stage that converts a PWM or PDM waveform into a high-efficiency audio output, driving a loudspeaker directly through an LC reconstruction filter. Within the broader audio IC taxonomy, the TFA9865 sits in the smart amplifier sub-category of power management and signal chain ICs, sitting alongside traditional Class-AB amplifiers but achieving far higher efficiency (typically >85 %) and lower thermal dissipation. Goodix's first-generation CoolPWM architecture is a proprietary, fully digital modulation scheme that breaks away from conventional Class-D topologies to minimize EMI and audible idle-channel noise. Key specifications include 7 W peak output into a typical 4 ohm or 8 ohm speaker load, an idle-channel noise floor of less than 7 uV, integrated DSP-based speaker protection algorithms, I2C/TDM control interface, and a small WLCSP footprint enabling direct placement adjacent to the smartphone or tablet speaker. Compared with discrete analog Class-D solutions, the TFA9865 reduces BOM count by integrating gate drivers, MOSFET power stage, and digital modulation in a single die. The CoolPWM digital architecture leverages advanced manufacturing processes to deliver high audio performance with very low power consumption. Built-in adaptive excursion control and thermal protection extend the usable loudness envelope of small speakers without causing voice-coil damage. This makes the device well suited to handset, tablet, and portable speaker applications where designers must push SPL limits within tight thermal budgets. Typical applications include smartphone and tablet loudspeaker amplification, portable Bluetooth speakers, wearable audio devices, and notebook/laptop speakers. The part is commonly paired with Goodix or third-party audio CODECs and digital microphone pre-processors to form a complete mobile audio playback chain. When designing with the TFA9865, pay close attention to PCB layout of the LC output filter, the placement of the bootstrap capacitor, and the thermal pad connection. Use a 4-layer stack-up with a solid ground plane directly beneath the part to minimize EMI coupling into adjacent RF circuits. This page synthesizes distributor pricing, drop-in alternatives, application examples, and practical design notes not found in the manufacturer product brief.
THS3061D - 300MHz High-Slew-Rate CFA | Texas Instruments
Texas Instruments THS3061D is a single, high-voltage, high-slew-rate current-feedback amplifier with a 300 MHz unity-gain bandwidth, 7000 V/us slew rate, and 8-pin SOIC package. The device is designed for low-distortion, large-signal amplification and uses Texas Instruments BICOM-1 process technology. A current-feedback amplifier, or CFA, is an analog amplifier architecture that uses feedback through an inverting input and offers high bandwidth and slew-rate performance for demanding signal chains. In the broader hierarchy, it belongs to the operational-amplifier family and the broader analog integrated-circuit category. Unlike a voltage-feedback amplifier, its bandwidth behavior depends strongly on the selected feedback resistor and gain setting. The supplied data identifies a 300 MHz unity-gain bandwidth, 120 MHz 0.1 dB bandwidth at a gain of 2, 7000 V/us slew rate at 10 MHz, and approximately -81 dBc third-order distortion. It also identifies ±145 mA output current into 50 ohm. These characteristics make the THS3061D suitable for video line drivers, VDSL line drivers, and other applications requiring large, linear output signals. The amplifier uses a current-feedback architecture rather than a conventional voltage-feedback input stage. In a typical implementation, the feedback network and input termination must be selected according to the manufacturer datasheet and the desired gain. The high slew rate can preserve large-signal amplitude in video and communication systems, while low distortion helps reduce signal degradation through the output stage. THS3061D is supplied in an 8-pin SOIC package and is specified for an operating temperature range of -40°C to +85°C in the supplied product data. The product page identifies the D package as an 8-pin SOIC. The supplied distributor result reports an in-stock quantity of 6,240 pieces and a unit price of $12.3490, while current pricing and availability should be confirmed at purchase. This page combines verified manufacturer and distributor information, application guidance, design notes, and an explicit distinction between confirmed drop-in alternatives and unavailable alternatives. The THS3061D is therefore best approached as a high-speed, high-voltage current-feedback amplifier for linear video and line-driver signal paths.