Amplifier ICs
بەرهەمەکان (3,200+)
TS522IDT - 15MHz Dual Low-Noise Op Amp | STMicroelectronics
STMicroelectronics TS522IDT is a dual precision operational amplifier with a 15 MHz gain-bandwidth product, 4.5 nV/√Hz low-voltage noise, and a 7 V/µs slew rate. The device operates from 2.5 V to 15 V and is packaged in an 8-pin SOIC for dual-amplifier signal-conditioning applications. An operational amplifier is a voltage-controlled, high-gain analog building block that compares an input signal with a feedback-defined reference. The TS522IDT contains two amplifiers in one package, placing it within the operational-amplifier hierarchy of analog ICs and broader semiconductor signal-processing components. Its dual configuration reduces package count when a board requires two closely related analog channels. The primary benefits are low input offset voltage, low voltage noise, and high dynamic performance. A 4.5 nV/√Hz noise density supports accurate amplification of small signals, while the 15 MHz gain-bandwidth product provides useful bandwidth for audio, instrumentation, filtering, and general-purpose analog stages. The 7 V/µs slew rate allows the amplifiers to follow changing signals with limited distortion. Each amplifier can operate with supply voltages between 2.5 V and 15 V, allowing operation from low-voltage analog systems through higher-voltage industrial analog rails. The monolithic dual-amplifier construction is intended to provide matching behavior between the two channels, although circuit-level offset and noise measurements should still be checked in the final design. The 8-pin SOIC package supports conventional surface-mount assembly and is convenient for prototypes as well as production boards. Typical uses include low-noise audio preamplification, microphone signal conditioning, active filtering, instrumentation amplifiers, sensor interfaces, and analog buffering. Two independent amplifier channels can process stereo audio, implement a differential input stage, or combine filtering with output buffering. Supply-headroom planning remains important because the usable output range depends on the selected rail voltages and output load. For low-noise layouts, use short feedback paths, keep input and ground connections away from switching nodes, and place input bypass capacitance close to the supply pins. Decoupling requirements and compensation limits should be confirmed in the STMicroelectronics TS522IDT datasheet. Stable operation also depends on following the prescribed capacitive-load limits and providing suitable output-current margin for the connected load. This product page combines the verified TS522IDT specifications, package information, replacement considerations, comparison parameters, and application guidance. It is intended to help engineers determine whether the dual amplifier fits a specific voltage, bandwidth, noise, and PCB-layout requirement before completing a prototype or production design.
TS522IN - 15MHz Dual Low-Noise Op Amp | STMicroelectronics
The STMicroelectronics TS522IN is a monolithic dual precision operational amplifier primarily intended for audio applications. Each amplifier provides a 15 MHz gain-bandwidth product, a 7 V/us slew rate, and low voltage noise of 4.5 nV/sqrt(Hz). The device is offered in an 8-pin mini-DIP package for through-hole PCB assembly. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain and negative feedback to amplify, buffer, filter, or compare small voltage signals. The TS522 belongs to the operational-amplifier hierarchy within linear and amplifier ICs. Its dual-channel architecture integrates two amplifiers in one package, reducing board area and simplifying dual audio-path or differential-signal designs. The TS522IN emphasizes low-noise signal handling, low input offset voltage, and high dynamic performance. Manufacturer descriptions identify a maximum input offset voltage of 850 uV, voltage noise of 4.5 nV/sqrt(Hz), gain-bandwidth product of 15 MHz, and slew rate of 7 V/us. The device also includes internal ESD protection rated at 2 kV and a macromodel for simulation. These characteristics make it relevant to audio preamplification, active filtering, buffering, and general low-noise analog signal chains. The dual amplifier can process two related signals independently, including left and right audio channels or the positive and negative sides of a differential circuit. Its 15 MHz bandwidth provides useful bandwidth for audio and wider-band analog stages, while the 7 V/us slew rate supports rapidly changing waveforms. The 4.5 nV/sqrt(Hz) voltage-noise figure helps reduce amplifier-added noise in high-gain stages, making the TS522IN most useful when the signal source impedance, resistor selection, and feedback topology are controlled carefully. Typical applications include stereo audio preamplifiers, microphone preamplifiers, active low-pass filters, audio buffers, sensor-conditioning stages, and small-signal audio-driver interfaces. The mini-DIP package is appropriate for legacy through-hole designs, test equipment, prototypes, and applications where hand insertion or socket assembly is preferred. Surface-mount production should use an electrically and mechanically verified SO-8-family option rather than assuming the DIP package is interchangeable. When designing around the TS522IN, begin with the power-supply limits and common-mode input range listed in the manufacturer datasheet. Confirm that source and sink output-current requirements remain within the operating limits at the selected gain and load. Place input and feedback components close to the device, maintain a stable ground reference, and use appropriate bypassing at each supply pin. Decoupling capacitors should be placed at the amplifier pins rather than at a distant power entry point. This page consolidates the TS522IN technical characteristics, package constraints, sourcing guidance, application fit, and verified cross-reference information. It also distinguishes documented device attributes from parameters that require confirmation in the manufacturer datasheet, helping engineers assess the part before PCB and production decisions.
TS524ID - Quad Low-Noise Audio Op Amp, 15MHz, SOIC-14 | STMicroelectronics
The STMicroelectronics TS524ID is a monolithic quad operational amplifier for precision audio signal paths, integrating four low-noise, high-fidelity amplifiers on one silicon die in a 14-pin SOIC (SO-14) surface-mount package. It combines a 15 MHz gain-bandwidth product, a 7 V/µs slew rate and 4.5 nV/√Hz input voltage noise with an input offset voltage of 950 µV maximum and total harmonic distortion of 0.002%. An operational amplifier, or op amp, is a high-gain differential amplifier with two inputs and one output that is used to amplify small signals faithfully across a wide frequency range. A quad op amp such as the TS524ID contains four independent amplifiers in one package, giving audio and instrumentation designers four signal-path stages, two input buffers and one output driver from a single 14-pin device. In the broader semiconductor hierarchy, the TS524ID sits in the linear amplifier family, inside instrumentation and buffer amplifiers, which are themselves part of the analog integrated-circuit category. Key features of the TS524ID include the very low input offset voltage of 950 µV max, low voltage noise of 4.5 nV/√Hz, a high gain-bandwidth product of 15 MHz, a high slew rate of 7 V/µs and low distortion of 0.002%. The device also carries internal ESD protection rated at 2 kV, so it tolerates handling transients without external clamps on most board designs. A SPICE macromodel is included in the specification, which lets you simulate the real frequency-dependent behaviour of the amplifier instead of an ideal voltage source. Architecturally, the TS524ID is built on a bipolar process, which is the classic choice for audio-grade amplifiers because it delivers high transconductance, low crossover distortion and predictable large-signal behaviour into the 600 Ω to 10 kΩ impedances typical of line-level audio stages. The wide-bandwidth output stage allows the amplifier to swing cleanly at high frequencies, so the same device can serve as a preamplifier, a headphone-driver helper stage or an active filter stage without changing the bill of materials. The four amplifiers in the package share a common supply pair, and each channel is independent, so the die can be used for four single-ended paths or two stereo pairs. Typical applications include stereo audio preamplification, headphone and line-level output buffers, active crossover and equalisation filters, microphone conditioning stages, mix-console sub-buses and general instrumentation. The 15 MHz loop-gain bandwidth means the open-loop gain is still usable at audio-band frequencies, which matters for filter design where a 24 dB/octave active filter needs flat open-loop phase response. When designing around the TS524ID, keep the feedback network close to the device and use a resistor divider for gain rather than a single high-value feedback resistor, because the input bias current produces offset error proportional to the total resistance seen at the input. Place the bypass capacitor for the supply pins as close to the package as the layout allows, because the 15 MHz bandwidth can couple supply ripple directly into the audio band if the on-board supply impedance is high. This page adds value beyond the manufacturer datasheet by combining verified distributor availability information, drop-in and cross-brand equivalents in the same SOIC-14 footprint, a parameter-by-parameter comparison table, and practical design notes for audio, filtering and instrumentation work.
TS524IDT - Low-Noise Quad Op Amp | STMicroelectronics
The STMicroelectronics TS524IDT is a monolithic quad operational amplifier with four amplifiers in a 14-pin SOIC package. It provides very low input voltage noise of 4.5 nV/√Hz, a maximum low-frequency input offset voltage of 950 µV, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. Designed for precision low-noise signal processing, the device is particularly suited to audio applications and other circuits requiring low distortion. An operational amplifier is a high-gain, differential analog amplifier used to amplify, buffer, filter, or control voltage signals. Quad operational amplifiers combine four amplifiers in one package, reducing board area and simplifying multi-channel designs. The TS524 belongs to the operational-amplifier hierarchy within analog and mixed-signal integrated circuits, where low input noise, low offset voltage, wide bandwidth, and high slew rate determine how faithfully small signals can be amplified. The TS524's 4.5 nV/√Hz input-noise density is the central feature for audio and precision instrumentation. Its low-noise behavior reduces the amplifier's contribution to the total input-referred noise, helping preserve small signals in microphone, line, and measurement front ends. A 15 MHz gain-bandwidth product supports wider signal bandwidth, while the 7 V/µs slew rate enables faster output transitions than lower-bandwidth general-purpose amplifiers. The device also offers a low maximum input offset voltage of 950 µV, which helps reduce output error when the amplifier is used with high closed-loop gain. Its output stage supports large output excursions, and its low distortion specification is 0.002%. Together, these characteristics make the TS524 suitable for balanced audio channels, active filters, line-level signal conditioning, and precision analog signal chains operating from low-noise sources. Typical uses include four-channel audio preamplification, microphone and line-input conditioning, active crossover or equalization networks, and instrumentation requiring consistent low-noise amplification. Because all four amplifiers are integrated in one package, channel matching and board-space savings are additional practical benefits for multichannel analog designs. Designers should verify the supply-voltage range, input common-mode range, output swing, and stability requirements in the STMicroelectronics manufacturer datasheet before finalizing the analog front end. Decoupling capacitors should be placed close to the supply pins, and sensitive input routes should be kept short to minimize board-level interference and added noise. This page organizes the verified TS524IDT specifications, source links, application guidance, and replacement analysis into an engineering-focused reference. It also highlights the device's 4.5 nV/√Hz noise, 15 MHz bandwidth, 7 V/µs slew rate, 950 µV maximum offset voltage, and 14-pin SOIC implementation for faster component evaluation.
TS524IN - Quad Low-Noise Precision Op Amp | STMicroelectronics
The STMicroelectronics TS524IN is a monolithic quad operational amplifier designed for low-noise audio applications, with four amplifier circuits in a 14-pin DIP package. Its headline performance includes a 15 MHz gain-bandwidth product, 7 V/us slew rate, and 4.5 nV/sqrt(Hz) input-voltage-noise density. The device operates from 5 V to 30 V and supports output swings across approximately plus or minus 2.5 V to plus or minus 15 V. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to improve signals applied to its two inputs. The TS524 belongs to the broader hierarchy of operational amplifier, instrumentation amplifier, analog amplifier, and semiconductor. Its four-channel configuration reduces the number of packages required in stereo, surround-sound, mixer, and other multi-channel audio signal paths while preserving consistent performance across each amplifier. Key characteristics include very low input-offset voltage, 4.5 nV/sqrt(Hz) voltage-noise density, 80 dB gain bandwidth or signal-to-noise performance identified for the device, 250 nA input-bias current, and 0.8 uA input-bias current figure listed for the family. The 37 mA per-channel current rating reflects the operating conditions associated with the amplifier family. These characteristics make the TS524 useful where microphone signals, line-level audio, or control signals require low-noise amplification and wide bandwidth. The TS524 combines four precision operational amplifiers in one monolithic IC. Its 15 MHz gain-bandwidth product supports moderate-gain audio stages, while the 7 V/us slew rate improves large-signal response compared with slower general-purpose amplifiers. The low 4.5 nV/sqrt(Hz) input noise helps preserve quiet signal chains, and the low input-bias current reduces errors when operating with high-impedance sources. Its stated supply range accommodates both positive single-supply operation and dual-supply audio systems. Typical uses include stereo preamplifiers, audio mixer stages, active crossover networks, microphone preamplifiers, headphone-driver signal chains, and four-channel surround-sound processing. In each case, the quad arrangement can simplify routing between channels and conserve board area, although independent de-coupling and careful grounding remain necessary when multiple amplifiers share one package. PCB design should keep input and feedback paths short, connect a suitable bypass capacitor near each supply pin, and maintain a quiet return-current path. Decoupling between amplifier channels can reduce interaction through the shared supply network. Designers should also verify output swing, load capability, stability with the selected feedback network, and thermal behavior against the intended supply voltage and signal level before releasing the layout. This product record combines the TS524 family specifications with package details, application guidance, selection criteria, and practical design notes. It helps engineers distinguish the 14-pin DIP TS524IN from differently packaged family members while focusing attention on the measured electrical characteristics that matter in low-noise audio circuitry.
TS7221BILT - Single BiCMOS R2R uPower Comparator | STMicroelectronics
The STMicroelectronics TS7221BILT is a single BiCMOS rail-to-rail micropower comparator housed in a 5-pin SOT-23 (SOT-23-5) package, designed for space- and weight-critical designs. It is fully specified at 2.7 V, 5 V and 10 V operation, drawing only a few microamperes of supply current while delivering rail-to-rail input performance and an open-drain output stage. The 'B' grade denotes a tighter input offset voltage grade versus the 'A' suffix variant, while the 'I' temperature suffix indicates the -40C to +85C industrial operating range and 'LT' indicates SOT-23-5 tape-and-reel packaging. A comparator is an analog building block that compares two input voltages and produces a logic-level output indicating which is larger. Micropower comparators like the TS7221 occupy a position in the power-management/analog signal-chain hierarchy below op-amps but above simple logic gates, and are favoured for always-on battery-powered designs where quiescent current dominates total energy consumption. Within ST's broader comparator family, the TS7221 sits alongside the TS7222 (dual) and TS7223 (quad) as the single-channel foundation of the series. Key features include rail-to-rail input common-mode range, an open-drain output that allows wired-OR logic and level-shifting to any pull-up voltage, very low supply current typically well under 10 uA, and 5 V/10 V operation suitable for industrial sensor interfaces. The BiCMOS process combines CMOS input stages with bipolar output drive for a balance of low power and reasonable switching speed. Internal ESD protection on the inputs (HBM 2000 V per the datasheet absolute maximum ratings) further improves robustness in handheld and field-deployed equipment. Typical applications include battery-pack voltage monitoring, threshold detectors, window comparators, and signal conditioning in IoT sensor nodes, wearables, and portable medical devices. The small SOT-23-5 footprint also makes the device attractive for space-constrained designs such as hearing aids and remote keyless-entry keyfobs. When designing with this part, choose the pull-up resistor on the open-drain output based on the desired propagation delay versus power budget; lower pull-up resistance speeds up edges but increases static current when the output is LOW.
TS902ID - Dual Rail-to-Rail Op Amp with Standby | STMicroelectronics
The STMicroelectronics TS902ID is a dual rail-to-rail CMOS operational amplifier with a standby position, offering 1.4 MHz gain-bandwidth product, 10 mV offset voltage, and operation from single or dual supplies up to 16 V in a 14-pin SOIC package. The device is intended for instrumentation, industrial control, and signal-conditioning systems where low-power standby operation and rail-to-rail input and output behavior are useful. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to set the gain. The TS902ID belongs to the operational-amplifier hierarchy, where a dual amplifier provides two amplifier channels in one package. Rail-to-rail input and output stages allow signals to approach the supply rails, while the standby function reduces supply consumption and places the outputs in a high-impedance state. Key features include rail-to-rail input and output voltage ranges, a 1.4 MHz gain-bandwidth product, and 10 mV typical input offset voltage. The amplifier supports single- or dual-supply operation from 2.5 V to 16 V according to the available manufacturer information, and its standby current is specified at 0.5 uA. The 14-SO package supports conventional surface-mount assembly and exposes both amplifier channels and the standby control. The TS902ID uses a CMOS operational-amplifier architecture designed for general-purpose analog signal conditioning. Its low standby current supports portable and instrumented systems that need to reduce consumption when measurements are not active. Rail-to-rail operation is useful when the available signal range is close to the supply voltage, although input common-mode, output swing, noise, and stability conditions still need to be checked against the application. Typical applications include low-power instrumentation, industrial sensor interfaces, battery-operated measurement equipment, audio and control-signal conditioning, and dual-channel analog systems. The dual-channel configuration can reduce board area when two independent signal paths are required. The standby position is particularly appropriate for systems that periodically disable the amplifier while retaining the device in the circuit. When laying out a TS902ID design, keep the input and output paths short, provide stable feedback compensation, and bypass the supply pins with suitable ceramic capacitance. Do not assume that standby mode preserves signal accuracy at the moment of switching; verify the timing against the system requirements. The manufacturer datasheet should be used for the complete electrical limits, pin connections, and application recommendations. This page combines verified manufacturer and distributor references with practical engineering guidance for instrumentation, power-conscious analog design, and drop-in replacement assessment.
TS902IDT - Dual 1.4MHz Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS902IDT is a dual general-purpose CMOS operational amplifier with rail-to-rail input and output voltage ranges, a 1.4 MHz gain-bandwidth product, and a low-power standby mode drawing 0.5 µA. The device is offered in the TS902IDT tape-and-reel configuration in a 14-pin small-outline package. Its dual amplifier arrangement provides two independent signal-conditioning channels in one package. A rail-to-rail operational amplifier is an amplifier whose input common-mode and output voltage ranges can extend close to the positive and negative supply rails. This makes the TS902 useful for low-voltage systems in which the signal can occupy much of the available supply voltage. In the broader device hierarchy, the TS902 is a dual CMOS operational amplifier, placing it within analog and mixed-signal integrated-circuit designs. The TS902IDT provides a 1.4 MHz gain-bandwidth product for general-purpose amplification at moderate frequencies. Its rail-to-rail input stage supports signal acquisition close to the supply limits, while the rail-to-rail output stage improves output-voltage range. A standby position reduces consumption to 0.5 µA and places the outputs in a high-impedance state, helping conserve power when the amplifier is not actively processing signals. The TS902IDT is specified for a temperature range of -40 °C to +125 °C. One retrieved technical listing identifies a maximum input offset voltage of 12 mV, while another reports a low bias current of 0.00015 µA. These figures support applications involving sensor interfaces, low-level signal conditioning, and battery-operated instrumentation where offset and input current are important selection criteria. Typical uses include portable sensor conditioning, industrial measurement, audio preamplification, low-voltage control systems, and current-feedback around transducers. The SOIC-14 package also permits a conventional surface-mount PCB layout with adequate separation between the two amplifier channels. Designers should account for the 12 mV maximum input offset when the application requires accurate DC measurements. Input and output stability must be evaluated with the selected feedback network and load, while supply bypassing should follow the manufacturer recommendations. The standby function should be driven only with signals that remain compatible with its defined logic levels. This product page combines package, temperature, frequency, offset, and power information with application-oriented engineering guidance. It also identifies the verified documentation links and explains the limits of the available drop-in replacement cross-reference, helping engineers distinguish a true pin-compatible substitution from a merely similar amplifier.
TS912ID - Dual Rail-to-Rail CMOS Op Amp | STMicroelectronics
STMicroelectronics TS912ID is a dual rail-to-rail CMOS operational amplifier with two independent amplifiers, an 8-pin SOIC package, and operation from single or dual supplies. Verified distributor listings identify it as a 2.7 V to 16 V device with approximately 800 kHz gain-bandwidth product and 1.3 V/us slew rate. The rail-to-rail input and output architecture supports signal stages whose operating range approaches the available supply voltage. An operational amplifier is an analog building block that uses high open-loop gain to amplify voltage differences while feedback determines the closed-loop behavior. A dual op-amp combines two amplifiers in one package, allowing designers to implement filters, buffers, level conversions, or paired signal-conditioning stages while reducing board area. CMOS construction supports low-power and low-noise signal-chain designs across industrial, instrumentation, communications, and consumer equipment. The TS912ID's rail-to-rail input range includes both supply rails, while its rail-to-rail output can swing close to the upper and lower limits. The verified 800 kHz bandwidth provides useful response for general-purpose low-frequency and moderate-frequency applications, while the 1.3 V/us slew rate supports faster transitions than very low-bandwidth precision amplifiers. Two independent, frequency-compensated amplifiers are contained in the same 8-SOIC package. Supply flexibility is central to the device: it can operate from a single 2.7 V minimum supply or from dual positive and negative rails. This makes it suitable for battery-powered instrumentation, active filtering, transducer interfaces, and general analog signal conditioning. Designers should still verify input and output common-mode limits, output-load behavior, noise, input-bias-current requirements, and stability against the conditions of the manufacturer datasheet. Typical uses include low-frequency active filters, sensor-signal conditioning, audio and communications interface blocks, voltage buffering, and two-channel sensor amplification. The SOIC-8 package is straightforward for conventional PCB assembly and breadboard or prototype layouts, although exposed-pad thermal management is not applicable. The primary design consideration is to place input, feedback, and decoupling components so that high-gain layouts remain stable. Keep sensitive input traces short, maintain a low-impedance ground reference, and follow the datasheet's recommended bypass capacitance. Verify the actual output swing against the load and required logic or sensor levels rather than assuming ideal rail-to-rail behavior. This page combines verified distributor pricing, manufacturer datasheet access, same-package replacement data, and practical selection guidance. It separates explicitly published facts from parameters requiring design verification, helping engineers source TS912ID without relying on generic amplifier descriptions.
TS912IN - Dual Rail-to-Rail CMOS Op Amp | STMicroelectronics
The STMicroelectronics TS912IN is a dual rail-to-rail CMOS operational amplifier with two amplifier channels, a 2.7 V to 16 V supply range, and an 8-pin Mini DIP package. The device supports single-supply or dual-supply operation, with rail-to-rail input and output voltage ranges. According to the manufacturer datasheet, its typical input bias current is only 1 pA, maximum input offset voltage is 2 mV, and supply current is approximately 200 µA per amplifier at a 3 V supply. These characteristics make the TS912IN suitable for low-power instrumentation, sensor interfaces, and signal-conditioning circuits that require low input bias and flexible supply operation. A CMOS operational amplifier is a voltage amplifier whose differential input controls the voltage applied to its output. Rail-to-rail input and output ratings allow the amplifier to operate close to the positive and negative supply rails, increasing the usable output range in single-supply systems. In the electronics hierarchy, the TS912IN is a dual operational amplifier, which belongs to the broader class of analog amplifier ICs and ultimately to integrated circuits used for analog signal processing. Key features include two independent amplifier channels, rail-to-rail input and output operation, and a 2.7 V to 16 V total supply range. The 1 pA typical input bias current is particularly useful for high-impedance sources because it minimizes source-loading error. Maximum input offset voltage of 2 mV supports accurate amplification of signals near the lower end of the input range. Operation from a 3 V supply at approximately 200 µA per amplifier also helps limit power consumption in battery-operated equipment. The TS912IN uses CMOS input circuitry to provide low bias current and low supply consumption. Rail-to-rail input behavior is important when the signal can approach either supply rail, while rail-to-rail output capability allows the output to use much of the available supply voltage. Designers should still account for output-current limits, load impedance, input common-mode behavior, and output-voltage headroom under the selected supply voltage and load conditions. Typical uses include low-power sensor signal conditioning, portable measurement instruments, battery-powered monitoring, and general-purpose analog filtering. The dual configuration allows one package to provide two amplifier channels for gain stages, buffers, comparators, or active filters. When the source impedance is high, the 1 pA typical bias current reduces loading, although PCB leakage and guard-ring techniques may still be necessary in demanding measurements. When designing around the TS912IN, use stable bypass capacitance at the supply pins and keep feedback components close to the amplifier pins to minimize parasitic effects. Confirm the required output swing, load, input range, and noise performance against the manufacturer datasheet before finalizing a high-gain or precision application. This page consolidates the verified manufacturer descriptions, distributor references, package information, technical characteristics, and substitution constraints for the TS912IN. It also distinguishes verified data from unavailable pricing, compliance, and pin-mapping details, helping engineers evaluate the amplifier without treating unverified substitute parts as drop-in equivalents.
TS914ID - Quad Rail-to-Rail CMOS Op Amp | STMicroelectronics
STMicroelectronics TS914ID is a quad rail-to-rail CMOS operational amplifier with a 1.4 MHz gain-bandwidth product, operating from 2.7 V to 16 V and supplied in a 14-pin SOIC package. The device accepts single or dual supply voltages and supports rail-to-rail input and output operation, allowing signals to approach either supply rail. Its extremely low 1 pA typical input bias current suits high-impedance sensing circuits, while the 2 mV maximum input offset voltage provides adequate precision for general-purpose analog signal conditioning. A CMOS operational amplifier is a voltage-controlled, high-gain analog building block whose differential input is amplified relative to ground or another reference voltage. The TS914 belongs to the operational-amplifier hierarchy, combining four amplifiers in one integrated circuit. It is designed for low-power, single-supply and dual-supply systems where four independent analog channels can be implemented in one compact 14-pin SOIC package. Key features include four amplifier channels, rail-to-rail input and output ranges, a 2.7 V to 16 V supply-voltage range, and a 1.4 MHz gain-bandwidth product. The typical input bias current of 1 pA is particularly valuable when source impedances are high, because it minimizes the voltage error caused by bias current. The reported 200 µA supply current per amplifier at 3 V also supports battery-powered and portable equipment when the required bandwidth is moderate. The TS914's CMOS input stage enables operation close to the supply rails and supports low input bias current. Its 1.4 MHz bandwidth is appropriate for general-purpose amplification, filtering, buffering, and signal conditioning rather than high-speed precision instrumentation. Because the maximum offset voltage is specified as 2 mV, applications demanding sub-millivolt accuracy require additional calibration or a more precise amplifier. Typical uses include four-channel sensor interfaces, low-frequency active filters, audio and communication signal conditioning, portable instrumentation, and industrial control modules. Placing all four channels in one SOIC package reduces board area and external component count. Input common-mode and output swing limits, output-current capability, noise, and stability should still be checked against the manufacturer datasheet before fixing the supply voltage and external network. For reliable single-supply operation, keep the input common-mode voltage within the supported range, place input and feedback components close to the device, and provide suitable bypassing at each supply pin. Decoupling requirements and compensation values must follow the manufacturer datasheet rather than generic assumptions. If the source resistance is high, account for input bias-current and capacitance errors, and confirm that the selected feedback topology remains stable at the intended gain. This product page consolidates verified manufacturer and distributor information with package, application, replacement, and design guidance. It distinguishes verified parameters from information that still requires datasheet review, helping engineers evaluate TS914ID without mistaking generic amplifier assumptions for guaranteed TS914ID characteristics.
TS914IN - 4-Channel Rail-to-Rail Op Amp | STMicroelectronics
STMicroelectronics TS914IN is a four-circuit, rail-to-rail CMOS operational amplifier designed for single or dual supply operation, with a 16 V maximum supply voltage, 1 pA typical input bias current, and a 2 mV maximum input offset voltage. The device is supplied in a 14-pin through-hole DIP package, allowing one package to implement four amplifier channels. A CMOS operational amplifier is a voltage-controlled, high-gain analog signal-processing component used for buffering, amplification, sensing, filtering, and feedback control. The TS914IN belongs to the operational amplifier hierarchy within analog integrated circuits, where its rail-to-rail input and output capability makes it suitable for systems whose signal levels approach the available supply rails. Key features include four amplifier circuits, rail-to-rail input and output operation, support for single or dual power supplies, very low 1 pA typical input bias current, and low input offset voltage no greater than 2 mV. According to the STMicroelectronics manufacturer datasheet, the device is intended for applications operating from a single supply or from dual supplies up to 16 V. The low input bias current is especially useful when the amplifier is connected to high-impedance sensors, because the amplifier contributes minimal loading to the source. Rail-to-rail behavior also broadens the usable input and output range in low-voltage systems. The trade-off is that the 14-pin DIP package is larger than modern surface-mount packages, making TS914IN more appropriate for through-hole, legacy, industrial, and prototyping assemblies. Typical uses include battery-powered instrumentation, sensor interfaces, low-voltage signal conditioning, sample-and-hold circuits, active filters, and general-purpose analog control systems. Its four independent channels can reduce the number of packages required when a board needs several similar low-power amplifier functions. When designing around TS914IN, verify input and output common-mode limits, output-current capability, operating-temperature limits, and stability requirements against the manufacturer datasheet for the exact operating conditions. Input bias, offset, and supply currents should be checked with the source impedance and signal bandwidth, particularly in high-impedance precision measurements. This page consolidates verified manufacturer and distributor information, package and pin details, replacement constraints, comparison data, and application-specific engineering guidance. It distinguishes confirmed specifications from unavailable values so engineers can make sourcing and PCB-retention decisions without relying on unsupported assumptions.
TS921ID - 4MHz High-Output RRIO Op Amp | STMicroelectronics
The STMicroelectronics TS921ID is a single rail-to-rail input and output BiCMOS operational amplifier optimized for 3 V and 5 V operation, with a 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and 80 mA output-current capability in an 8-pin SOIC package. An operational amplifier is a voltage-controlled differential amplifier that uses high open-loop gain to amplify small input signals. The TS921 belongs to the rail-to-rail input/output, or RRIO, family, allowing its input common-mode range and output swing to approach the supply rails. This makes it useful for low-voltage battery-powered equipment, sensor interfaces, audio stages, industrial controls, and portable instruments where the signal can occupy much of the available supply range. The TS921's principal features include low input noise of 9 nV/sqrt(Hz), a 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and an output stage capable of delivering 80 mA. The manufacturer identifies the device as optimized and fully specified for 3 V and 5 V supplies, while verified distributor data also gives a 2.7 V to 12 V operating-voltage range. Rail-to-rail operation reduces the need for separate positive and negative supply rails in single-supply designs. The BiCMOS process combines bipolar input characteristics with CMOS output circuitry. In practical signal chains, the TS921 can condition low-level sensor outputs, buffer precision ADC inputs, or provide general-purpose gain. Its 80 mA output capability is useful for driving moderate loads, although sustained heavy loading can reduce output swing and increase power dissipation. The 4 MHz bandwidth supports applications requiring moderate rather than high-frequency closed-loop performance. Typical uses include battery-operated instrumentation, low-voltage audio, industrial sensor conditioning, active filters, and portable measurement equipment. The SOIC-8 format supports conventional surface-mount assembly, while the manufacturer datasheet provides the authoritative pin connection and recommended application information for layout and decoupling decisions. For single-supply operation, reserve output headroom for the load and check the input common-mode range across the complete signal excursion. Place the supply bypass capacitor close to the positive and ground pins, and use short, low-impedance feedback routes to limit parasitic feedback and preserve stability. This product page combines the verified manufacturer and distributor information with package, application, comparison, and design guidance. It identifies where TS921ID fits, highlights the 4 MHz bandwidth and 80 mA output-current capabilities, and clearly separates confirmed data from engineering details that require additional verification.
TS921IN - 4MHz Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS921IN is a single-amplifier operational amplifier with a 4 MHz gain-bandwidth product, 1 V/µs slew rate, rail-to-rail input and output capability, and an 8-DIP package. Its 80 mA typical output current supports higher-capacitive and load-driving capability than a conventional low-current general-purpose amplifier. An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, compare, filter, and control signals. The TS921IN belongs to the operational-amplifier hierarchy, which falls under analog amplifier ICs and broader semiconductor signal-conditioning devices. Its rail-to-rail input and output architecture is useful when the usable input or output range must extend close to the supply rails. Key characteristics include a 4 MHz gain-bandwidth product, 1 V/µs slew rate, low input-referred noise density of 9 nV/√Hz, and typical output current of 80 mA. The single-amplifier configuration allows a PCB footprint to remain compact, while the 8-DIP package provides straightforward through-hole assembly. The listed operating temperature range is -40°C to +125°C, supporting industrial-temperature applications. The TS921IN combines rail-to-rail signal handling with relatively high bandwidth and output-drive capability. Its low-noise specification is particularly useful for low-level audio, instrumentation, sensor-interface, and general analog signal-conditioning circuits. The 80 mA output current also allows the amplifier to drive more demanding loads than a typical comparator-oriented or ultra-low-power op amp, provided the supply voltage and thermal limits remain satisfied. Typical uses include low-level sensor amplification, active filtering, audio preamplification, buffer stages, threshold and comparator-style interfaces, and general industrial control circuitry. It can also serve as a rail-to-rail input/output buffer in systems where the input signal approaches either supply rail. Designers should still verify stability, output swing, load capability, and noise performance against the complete circuit requirements. A key design consideration is the trade-off between bandwidth, noise, and output drive. The TS921IN is more capable than a low-power, low-bandwidth amplifier, but it is not necessarily the optimal choice for every precision or micropower design. Input and output stability should be evaluated with the actual source impedance, load, supply voltage, and external compensation network. This page combines verified distributor specifications and availability with a practical TS921IN selection guide, application analysis, datasheet references, and defensible family alternatives. Pricing reflects the verified $0.58 unit-price listing as of October 29, 2026, while unavailable technical fields are explicitly marked rather than estimated.
TS921IPT - 4MHz RRIO High-Output Op Amp | STMicroelectronics
The STMicroelectronics TS921IPT is a single, rail-to-rail input and output BiCMOS operational amplifier featuring 4 MHz gain-bandwidth product, 1 V/us slew rate, 9 nV/Hz low-noise performance, and 80 mA output-current capability in an 8-pin TSSOP package. The device is optimized and fully specified for operation from 3 V and 5 V, with operating supply voltage extending to 12 V. An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to buffer, amplify, filter, or compare voltage signals. The TS921 belongs to the broader rail-to-rail operational-amplifier category, combining low-noise BiCMOS input and output stages with the ability to swing close to both supply rails. This makes it useful when signals must be processed with minimal rail-to-rail headroom restrictions. The TS921IPT combines rail-to-rail input and output operation with a 4 MHz gain-bandwidth product and 1 V/us slew rate. Its 9 nV/Hz voltage-noise density supports precision signal-chain work, while its 80 mA output-current capability can drive up to 32 loads according to the manufacturer description. Low distortion, internal ESD protection rated at 1.5 kV, and latch-up immunity improve robustness in practical analog circuits. The BiCMOS architecture balances low input-noise behavior with high output-drive capability. A gain-bandwidth product of 4 MHz supports signal amplification at moderate frequencies, and the 1 V/us slew rate improves large-signal response compared with slower general-purpose amplifiers. The 8-pin TSSOP-8 package permits compact surface-mount implementation, while rail-to-rail operation reduces the need to keep input and output voltages strictly inside the supply rails. Typical uses include low-noise sensor conditioning, audio signal paths, current sensing, active filtering, instrumentation, and general-purpose buffering. The 80 mA output capability is particularly relevant when the amplifier must drive a relatively heavy capacitive or resistive load. Designers should still check load stability and output-current limits for the complete application rather than relying on peak capability alone. Decoupling should be placed close to the supply pins, and sensitive input routing should avoid proximity to switching nodes and high-current return paths. The amplifier must operate within its specified common-mode and supply-voltage limits. Because the available package drawing could not be independently verified against a pin-description table, use the manufacturer datasheet before assigning PCB tracks or making pin-sensitive substitutions. This page combines the verified TS921IPT operating characteristics with practical application guidance, sourcing instructions, and a focused drop-in assessment. The alternative list intentionally excludes unverified cross-package or speculative equivalents so that engineers can distinguish a genuine TSSOP-8 replacement from a merely similar amplifier.
TS9222ID - Dual Precision Rail-to-Rail Op Amp | STMicroelectronics
STMicroelectronics TS9222ID is a dual precision operational amplifier optimized for low-noise and stable signal amplification, with rail-to-rail input and output operation, 4 MHz gain-bandwidth product, and 1.3 V/us slew rate in an 8-pin SOIC package. It operates from 2.7 V to 12 V and is specified for -40C to +125C operation. An operational amplifier is an active analog component that uses high open-loop gain to amplify voltage differences between its differential inputs. Within the analog signal-chain hierarchy, an op amp sits between passive sensor conditioning and higher-level conversion or control functions. Rail-to-rail input and output operation allows the TS9222ID to accept signals near the positive or negative supply rail, while its output can also swing close to those rails. Key characteristics include a maximum input offset voltage of 500 uV, 80 mA output current per channel, and low input bias current. The 4 MHz gain-bandwidth product supports closed-loop operation at moderate signal frequencies, while the 1.3 V/us slew rate gives adequate performance for precision feedback networks, instrumentation, and low-to-moderate-frequency signal conditioning. The dual configuration provides two amplifiers in one package, reducing component count on analog boards. The TS9222ID is built for precision and stability rather than maximum bandwidth. Its 500 uV maximum input offset voltage limits the output error created by input imbalance in a unity-gain configuration. Rail-to-rail inputs help preserve signal integrity in sensor interfaces where the operating point may sit near a supply rail. The stated 80 mA per-channel output capability also allows the amplifier to drive heavier loads than a purely high-impedance signal-processing stage. Typical applications include current sensing, bridge and instrumentation amplifiers, sensor conditioning, audio preamplification, industrial measurement systems, and automotive electronic modules. The -40C to +125C temperature range supports extended industrial environments, provided that the board-level power supply, bypass capacitors, and stability network follow the manufacturer's recommended implementation. For reliable operation, place the input and feedback components close to their corresponding pins, bypass each supply rail locally, and verify capacitive-load stability with an isolation resistor when driving cables, ADC inputs, or other long capacitive loads. Use the manufacturer pin-description table when assigning PCB tracks and confirm that the selected amplifier configuration remains stable across the intended gain, load, and supply range. This page combines package, precision, temperature-range, and interface guidance with same-family drop-in options and a parameter-by-parameter comparison. It is intended to help engineers shorten selection work while preserving the electrical and layout constraints that determine analog performance.
TS9224ID - 4-Channel Precision Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS9224ID is a four-circuit, general-purpose operational amplifier optimized for precision, low noise, and stability, with rail-to-rail input and output operation in a 14-pin SOIC package. Key ratings include 500 uV maximum input offset voltage, 4 MHz gain-bandwidth product, 1.3 V/us slew rate, 9 nV noise, and 500 pF capacitive-load drive capability. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify small voltage differences. Its hierarchy extends from operational amplifier to analog amplifier, linear amplifier, and analog semiconductor. The TS9224 quad configuration integrates four amplifiers into one package, reducing board area while preserving independent signal paths for instrumentation, buffering, filtering, and precision control applications. Rail-to-rail input and output behavior supports operation near the supply rails, which is useful when signal range is limited by available supply voltage. The 500 uV maximum offset-voltage rating supports precision-focused designs, while the 4 MHz gain-bandwidth product and 1.3 V/us slew rate provide useful bandwidth for general-purpose closed-loop amplifier stages. The manufacturer also identifies 500 pF capacitive-load drive and 9 nV noise as principal device characteristics. The TS9224 family is optimized around low-noise, high-precision operation with particular emphasis on stability. This combination suits instrumentation and industrial signal paths where input offset, noise, and closed-loop behavior affect measurement quality. Four independent amplifiers in a single package can also simplify designs requiring multiple similar analog channels, although each amplifier requires correct input common-mode, output swing, and output-current conditions. Typical uses include low-level sensor conditioning, current-sense amplifier outputs, bridge-signal interfaces, analog filtering, and precision control loops. In each case, stable closed-loop operation and rail-to-rail signal handling can reduce the need for separate input or output buffers, provided the feedback network is designed for the required gain and bandwidth. For PCB implementation, use the manufacturer's pin configuration when assigning inputs, outputs, supply rails, and feedback components. Place input, output, feedback, and decoupling connections to minimize loop area and susceptibility to noise. Because the device can drive capacitive loads up to 500 pF, isolate difficult loads with series resistance when necessary to preserve stability. This product page combines the TS9224ID electrical characteristics, package details, drop-in alternatives, comparison parameters, and application-focused design guidance to support component selection, PCB planning, and precision analog circuit design.
TS922AID - Dual Rail-to-Rail Op Amp | STMicroelectronics
STMicroelectronics TS922AID is a dual rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with low noise of 9 nV/√Hz, low distortion of 0.005%, and high output current of 80 mA in an 8-pin SOIC package. It operates from the supply rails up to 12 V and is designed for low-impedance loads. An operational amplifier is an analog signal-conditioning IC that amplifies the difference between two input voltages. A dual amplifier contains two independent amplifiers in one package, while a rail-to-rail input and output stage allows operation close to both supply-voltage limits. The TS922AID therefore occupies the amplifier, analog IC, and semiconductor hierarchy while serving precision audio, buffer, and low-load drive applications. The principal features include rail-to-rail input and output capability, 80 mA output current, 9 nV/√Hz input noise, 0.005% distortion, a 4 MHz gain-bandwidth product, and a 1 V/µs slew rate. These characteristics combine low-noise signal handling with enough output drive to operate 32 low-impedance loads according to the manufacturer description. The TS922AID uses a BiCMOS process that combines bipolar input circuitry with CMOS output stages. Its high output current is the principal architectural distinction from many general-purpose dual amplifiers, especially when the output must remain low-impedance while operating near the supply rails. The 3 V and 5 V optimization also makes it appropriate for compact, low-voltage analog systems. Typical uses include audio preamplifier stages, active filters, sensor-conditioning circuits, low-impedance buffer applications, and portable test or measurement equipment. The dual configuration allows two related signal paths to be implemented in one package, reducing board area and simplifying dual-rail analog front ends. For stable operation, follow the manufacturer datasheet for supply-decoupling close to the power pins and for output-load limits. Input and output common-mode ranges, input bias current, offset voltage, and exact operating-temperature limits should be checked against the specific operating point before production release. This page organizes the manufacturer specifications, sourcing information, application guidance, and verified drop-in options for engineers evaluating the TS922AID. It also distinguishes confirmed pin-compatible choices from family members that differ in grade, package, or packaging and therefore require separate engineering review.
TS922ID - Dual Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS922ID is a dual, rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, housed in an 8-pin small-outline integrated circuit package. Its two amplifier channels feature high output-current capability for driving low-load impedances, while the rail-to-rail input and output stages make it suitable for systems whose signal levels approach the supply rails. An operational amplifier is a high-gain, high-impedance analog amplifier used to amplify, buffer, compare, or filter signals. The TS922ID belongs to the operational-amplifier family within analog integrated circuits, providing two independent amplifier channels in one package. Rail-to-rail operation means the amplifier can process input and output signals close to the positive and negative supply limits, which improves utilization of the available supply voltage in mixed-signal systems. The TS922 and TS922A family is specifically described by STMicroelectronics as a dual BiCMOS operational-amplifier family optimized and fully specified for 3 V and 5 V operation. The TS922ID also provides high output currents, allowing the device to drive low-load impedances. These characteristics make it useful in audio output stages, sensor-conditioning circuits, active filters, and low-voltage industrial or battery-powered equipment. The TS922ID is identified as an active, RoHS-compliant, standard general-purpose amplifier with an operating temperature range of -40 °C to +125 °C. The device is supplied in an SOIC-8 package, and distributor listings identify the TS922ID as a dual amplifier with rail-to-rail operation. Because the device combines two amplifiers in one package, it can also reduce board area in designs that require two buffered or amplifying channels. A key application consideration is that the available supply voltage and load current determine whether the output stage remains within its intended operating region. Designers should also observe the absolute maximum ratings and recommended operating conditions in the STMicroelectronics datasheet, provide appropriate bypass capacitance near the supply pins, and confirm that the connected load does not exceed the amplifier's specified drive capability. This page combines the manufacturer datasheet, distributor inventory information, and verified cross-reference findings. It also distinguishes documented TS922ID data from parameters that require confirmation from the full datasheet or distributor inventory before production release.
TS922IN - Dual 4MHz Rail-to-Rail Op Amp | STMicroelectronics
STMicroelectronics TS922IN is a dual, rail-to-rail input and output BiCMOS operational amplifier optimized for 3 V and 5 V operation, with a 4 MHz gain-bandwidth product, 1 V/µs slew rate, and high output-current capability. The device is supplied in an 8-pin Mini DIP package and contains two independent amplifiers. According to the STMicroelectronics manufacturer datasheet, its rail-to-rail stages allow input and output voltages to approach the supply rails, while the BiCMOS architecture combines low input bias current with CMOS-style low power consumption. An operational amplifier is a high-gain, high-impedance analog signal-conditioning circuit used for voltage amplification, buffering, filtering, and closed-loop feedback control. Within the broader semiconductor hierarchy, the TS922IN is a dual precision analog amplifier, falling under the categories of operational amplifier, analog IC, and semiconductor. Its two amplifier sections can independently process signals or operate together in differential and analog signal-conditioning circuits. Key electrical characteristics include a 4 MHz gain-bandwidth product, 1 V/µs slew rate, low noise identified as 9 nV/√Hz, and output-current capability up to 80 mA. The supported supply range is 2.7 V to 12 V, with operation optimized around 3 V and 5 V rails. Rail-to-rail input and output behavior is especially useful when signal amplitudes occupy much of the available supply-voltage range. The 80 mA output capability also permits relatively low-load-impedance drive compared with many general-purpose dual amplifiers. The TS922 family uses a BiCMOS input stage to combine bipolar-device characteristics with CMOS power behavior. Its dual architecture saves board area by placing two amplifiers in one package. The manufacturer describes the devices as optimized and fully specified for 3 V and 5 V operation, while also identifying a wider operating range extending to 12 V. This makes the TS922IN relevant to industrial controls, sensor interfaces, audio paths, data acquisition, and general dual-amplifier designs. Typical uses include low-level sensor conditioning, active filtering, audio preamplification, voltage buffering, and mixed-signal circuits requiring two amplifiers. The rail-to-rail output is useful when driving subsequent stages whose common-mode range is limited. The high output current can also reduce the need for an additional output-buffer stage in moderate-load applications. Designers should verify output swing, input common-mode behavior, load stability, and noise at the actual supply voltage and operating frequency. Decoupling capacitors should be placed close to the supply pins, and unused amplifier sections should be configured according to the manufacturer datasheet rather than left floating. The 8-pin Mini DIP package also requires adequate spacing for through-hole assembly and careful handling during insertion. This page combines manufacturer specifications, verified distributor information, package guidance, drop-in alternatives, comparison data, and practical application notes. It is intended to help engineers identify whether the TS922IN fits a 3 V or 5 V dual-amplifier design before purchasing or modifying an existing PCB.
TS922IPT - Dual Rail-to-Rail 4 MHz Op Amp | STMicroelectronics
STMicroelectronics TS922IPT is a dual rail-to-rail input and output BiCMOS operational amplifier rated for 2.7 V to 12 V operation. It provides two amplifier channels, 4 MHz gain-bandwidth performance, a 1.3 V/us slew rate, and rail-to-rail input and output stages in an 8-pin TSSOP package. The device is optimized and fully specified for 3 V and 5 V systems. An operational amplifier is an analog signal-conditioning semiconductor that amplifies the voltage difference between its two inputs while providing high input impedance, low output impedance, and stable operation around a feedback-defined voltage. The TS922 belongs to the operational-amplifier hierarchy, where a dual BiCMOS amplifier combines bipolar input characteristics with CMOS-compatible output drive for low-power mixed-signal systems. The TS922IPT's rail-to-rail inputs allow sensing signals close to either supply rail, while rail-to-rail outputs improve dynamic range in single-supply circuits. Its high output-current capability is intended for driving relatively low-impedance loads. Low distortion of 0.005% and very low noise make the amplifier useful in audio and other precision analog paths. The dual configuration also reduces component count when two independent gain stages are required. STMicroelectronics identifies the TS922 family as a BiCMOS dual operational amplifier optimized for 3 V and 5 V operation. The 4 MHz gain-bandwidth product supports moderate-bandwidth signal conditioning, including active filtering, sensor amplification, and audio stages. The 1.3 V/us slew rate improves large-signal response, although higher-frequency designs should verify stability, load capacitance, and noise-gain requirements. Typical uses include audio preamplification, low-load-impedance driver stages, sensor interfaces, active filters, and portable 3 V or 5 V equipment. It is particularly relevant when dual-channel signal conditioning is needed without introducing rail-to-rail input/output limitations common in older amplifier families. PCB design should keep input and feedback paths short, place compensation or filtering capacitors close to their associated pins, and maintain a solid ground reference. Decoupling capacitors should be connected to the supply and ground pins with minimal loop area. Designers should also verify output swing and capacitive-load stability against the circuit's load current and impedance. This product page combines manufacturer specifications, exact drop-in candidate screening, application guidance, pin assignments, and a practical comparison framework. It helps engineers distinguish electrically different family variants from mechanically compatible alternatives before approving a PCB substitution.
TS924ID - Quad Rail-to-Rail Op Amp | STMicroelectronics
STMicroelectronics TS924ID is a four-circuit, rail-to-rail BiCMOS operational amplifier with an 80 mA output-current rating, 80 dB CMRR, and a maximum bias current of 0.1 µA, supplied in a 14-pin small-outline package. The device is optimized for 3 V and 5 V operation and is intended for low-voltage signal conditioning, audio, portable equipment, and general-purpose analog systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. A quad package contains four independent amplifier sections, allowing one TS924ID to implement four amplifier channels in a single 14-pin package. Rail-to-rail input and output operation helps preserve signal range in low-voltage systems where conventional amplifier stages may approach their supply limits. Key features include four amplifier circuits, rail-to-rail operation, an 80 mA cited output-current capability, 80 dB common-mode rejection ratio, and a maximum input bias current of 0.1 µA. The TS924 family is described as a low-noise, low-distortion BiCMOS design. Its low bias current is particularly useful in high-impedance sensing paths, while the rail-to-rail characteristics support compact, low-voltage equipment. The bipolar input stage and CMOS output stage form the BiCMOS architecture used in the TS924 family. Input bias current, common-mode rejection ratio, offset voltage, output-current capability, noise, and distortion are the principal parameters to check when comparing it with other quad low-voltage operational amplifiers. The verified TS924ID information cites a maximum offset of 5000 µV, a maximum bias current of 0.1 µA, and an 80 mA output-current feature. Typical uses include low-voltage audio signal conditioning, portable and battery-operated equipment, current or voltage sensing interfaces, active filtering, and general analog buffers. Four amplifiers in one package can reduce board area when a design needs several channels. Applications requiring wider supply voltage, lower offset, lower noise, or different logic levels should verify those requirements against the complete manufacturer datasheet before production use. Designers should provide adequate input and output bypassing, verify stable operation with the intended load and feedback network, and confirm that the amplifier input common-mode range includes the full signal swing. Because the output-current figure is a headline feature rather than a complete load-capability specification, cable, headphone, and capacitive-load applications require careful review of the datasheet's output-stage limits. This product page consolidates verified distributor availability, pricing, environmental information, same-package alternatives, and practical selection guidance. It also distinguishes documented TS924ID facts from parameters that still require confirmation from the manufacturer datasheet, helping engineers narrow a replacement without making an unverified electrical assumption.
TS924IDT - Quad Rail-to-Rail Op Amp, 4 MHz | STMicroelectronics
The STMicroelectronics TS924IDT is a quad, rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with four amplifiers housed in a 14-pin Small Outline package. Key specifications include a 4 MHz gain-bandwidth product, 1.3 V/µs slew rate, and a 2.7 V to 12 V supply-voltage range. An operational amplifier is an active analog signal-conditioning device that amplifies the voltage difference between its inverting and non-inverting inputs. The TS924 belongs to the quad operational-amplifier family, placing four amplifiers in one package to reduce component count in multi-channel instrumentation. Its rail-to-rail input and output architecture supports low-voltage signal chains in which the usable common-mode and output ranges extend close to the supply rails. The BiCMOS construction combines bipolar input transistors with CMOS output stages. In the TS924, this architecture supports low input-bias current of 15 nA, a 4 MHz unity-gain bandwidth, and 1.3 V/µs slew rate. The device is specified for both 3 V and 5 V systems and operates across a supply range of 2.7 V to 12 V. The operating temperature range extends from -40 °C to +125 °C. Typical applications include current-to-voltage conversion in precision measurement systems, sensor-signal conditioning, low-voltage audio circuits, active filtering, and general-purpose analog signal conditioning. Because four matched amplifier channels share one package, designers can also use the device for dual-rail control loops, quad sensor interfaces, and multi-axis signal acquisition. When laying out a TS924IDT circuit, place each decoupling capacitor close to its corresponding supply pin and keep feedback resistors and input traces short to minimize parasitic capacitance. Verify the input common-mode range, output-current capability, and capacitive-load stability against the load connected to each amplifier. The SO-14 outline is suitable for conventional surface-mount assembly and supports design reuse across the STMicroelectronics TS92x family. This page consolidates the manufacturer specifications, package and lifecycle information, price references, cross-reference findings, and practical design guidance into one engineering-focused resource for evaluating the TS924IDT in new analog designs.
TS924IN - Quad 4MHz Rail-to-Rail Op Amp | STMicroelectronics
STMicroelectronics TS924IN is a quad, rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with four amplifier channels, 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and low input-offset voltage up to 900 uV. The device is supplied in a 14-pin DIP package, making it suitable for conventional through-hole and legacy industrial designs. An operational amplifier is a high-gain analog signal-conditioning IC used in the broader voltage-amplifier and analog IC hierarchy. The TS924IN combines four independent amplifiers in one package, allowing compact implementation of filters, amplifiers, comparators, instrumentation circuits, and signal-conditioning stages. Its rail-to-rail output design supports operation close to the supply rails, while its BiCMOS construction combines bipolar input characteristics with CMOS output stages. The headline specifications are 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and input offset voltage of 900 uV maximum. The TS924 family is fully specified for 3 V and 5 V supply operation, and the supplied operating-range information extends to 12 V. Its high output-current capability is particularly useful for driving low-impedance loads compared with many general-purpose op-amplifier choices. Each channel can operate as an amplifier, comparator, or active-filter building block. The wide available bandwidth supports signal paths that need more gain-bandwidth than low-speed precision-oriented amplifiers, while the 1.3 V/us slew rate allows moderate-amplitude signals to transition without excessive distortion. Four integrated channels can reduce package count and simplify board layout in multi-channel measurement and control systems. Typical uses include industrial sensor interfaces, low-voltage audio and communication circuits, active filters, data-acquisition front ends, process-control loops, and general-purpose analog signal conditioning. The 14-DIP format is especially useful when maintaining an existing through-hole design or avoiding a conversion to a surface-mount footprint. Input and output protection should still be considered because the verified data does not establish the maximum input or output voltage range. The principal design consideration is the power relationship between supply voltage, output swing, load current, and dissipation. Because no thermal-resistance or absolute maximum-rating data was included in the verified results, those values must be confirmed in the manufacturer datasheet before production release. Decoupling capacitors should be placed close to the supply pins and return pins should follow a low-impedance layout. This product record combines verified manufacturer and distributor information, package-specific replacement guidance, practical design considerations, and a parameter comparison that helps engineers distinguish true pin-compatible alternatives from merely functional substitutes. It supports component selection for legacy 14-DIP analog designs without treating incompatible package or performance variants as drop-in replacements.