بەرهەمەکان (3,200+)

ISO124U/1K - ±10V Precision Isolation Amplifier | Texas Instruments
ISO124U/1K

ISO124U/1K - ±10V Precision Isolation Amplifier | Texas Instruments

The Texas Instruments ISO124U/1K is a precision, low-cost isolation amplifier for sensing bipolar voltages within a ±10-V input range. It uses duty-cycle modulation and demodulation to transmit the measured signal across a 2-pF differential capacitive barrier, providing galvanic isolation between the input and output sides. The device is packaged in an 8-pin SOIC (DVA) package and is designed for measurement and control systems that require signal isolation. An isolation amplifier is a specialized interface amplifier that transfers a low-level input signal while electrically separating the input circuitry from the output circuitry. The isolation barrier prevents ground-potential differences and high-voltage events on one side of the system from corrupting measurements or damaging downstream circuitry. In the power-management hierarchy, the ISO124U/1K belongs to the isolation-amplifier and signal-conditioning IC category, where accurate voltage sensing, galvanic isolation, and compact implementation are the primary design goals. The ISO124U/1K supports a precision isolation-amplifier configuration with fixed unity gain and bipolar operation. According to the Texas Instruments product information, maximum nonlinearity is 0.010%, signal bandwidth is 50 kHz, and input offset-voltage temperature drift is 200 µV/°C. These characteristics make the device suitable for industrial instrumentation, current-voltage sensing, power-conversion feedback, and isolated control or measurement circuits. The device operates from dual supplies in the range of ±4.5 V to ±18 V, allowing it to interface with systems using conventional analog rails. Quiescent current is approximately ±5 mA on VS1 and ±5.5 mA on VS2. The ISO124 family is also characterized by high-voltage isolation testing and a rated isolation barrier of 1500 Vrms, although final working-voltage and safety-limit decisions must be based on the complete system requirements and manufacturer documentation. Typical uses include isolated shunt measurement, inverter and motor-control feedback, power-supply monitoring, test and measurement equipment, and industrial communication interfaces. The 50-kHz bandwidth is sufficient for many control and sensing signals but is not intended for high-frequency waveform capture. The capacitive isolation barrier should be treated as a safety-critical component when it is part of an end-product isolation barrier. When designing around the ISO124U/1K, provide local decoupling close to the supply pins and respect the input common-mode range. The input voltage range is limited to ±10 V, so larger process signals require attenuation or protection. Confirm the output swing, supply polarity, isolation rating, and system creepage and clearance requirements before releasing a production design. This page combines manufacturer specifications, distributor availability information, and same-footprint alternatives for engineering selection.

RFQ پەیوەندی
ISO124U/1KG4 - 50kHz Isolation Amplifier | Texas Instruments
ISO124U/1KG4

ISO124U/1KG4 - 50kHz Isolation Amplifier | Texas Instruments

The Texas Instruments ISO124U/1KG4 is a precision isolation amplifier with a 50 kHz signal bandwidth, maximum nonlinearity of 0.010%, and input offset-voltage drift of 200 µV/°C, housed in an 8-pin SOIC package. The device supports dual supply rails from ±4.5 V to ±18 V and draws 5 mA from VS1 and 5.5 mA from VS2. An isolation amplifier is a precision signal-conditioning IC used to transfer an analog voltage across a high-impedance barrier while preventing direct electrical conduction between the input and output domains. The ISO124 belongs to the broader isolation-amplifier, analog-signal-conditioning, interface-IC, and semiconductor hierarchies. Its isolation barrier supports instrumentation systems that require signal transfer without a conductive path between the measured circuit and the readout electronics. The ISO124 uses duty-cycle modulation and demodulation to transmit the signal digitally across a differential capacitive barrier. Because the information is represented by modulation rather than analog voltage amplitude, barrier characteristics do not directly determine signal-integrity performance. Key features include 0.010% maximum nonlinearity, 50 kHz bandwidth, and 200 µV/°C offset-voltage drift. The dual-supply range of ±4.5 V to ±18 V permits operation from low-voltage analog systems through higher-voltage industrial rails. Quiescent current is 5 mA on VS1 and 5.5 mA on VS2, making the device suitable for precision measurement circuits where supply efficiency and signal accuracy must be balanced. The 8-pin SOIC footprint supports conventional surface-mount assembly and compact analog boards. Typical uses include isolated current sensing, industrial process-control inputs, sensor-interface circuits, power-conversion feedback isolation, and test-and-measurement front ends. The 50 kHz bandwidth accommodates signals that vary more quickly than static voltage references while retaining the accuracy expected from precision isolation stages. When laying out an ISO124U/1KG4 circuit, place supply bypassing close to the device and maintain the isolation boundary required by the system architecture. Confirm input common-mode range, supply sequencing, and barrier-layout recommendations in the manufacturer datasheet. Treat the 50 kHz bandwidth and 0.010% nonlinearity as separate design limits because a signal within the bandwidth can still incur meaningful gain or linearity error. This page consolidates the manufacturer specifications, practical application guidance, drop-in family options, and engineering trade-offs needed to evaluate the ISO124U/1KG4 before incorporating it into a precision isolated-interface design.

RFQ پەیوەندی
L2720D13TR - 1A Dual Power Op Amp | STMicroelectronics
L2720D13TR

L2720D13TR - 1A Dual Power Op Amp | STMicroelectronics

STMicroelectronics L2720D13TR is a dual low-side power operational amplifier capable of delivering output current to 1 A. It operates from single or split supplies, accepts large common-mode and differential-mode input ranges, and is packaged in a 16-lead small-outline SOIC. The device also provides ground-compatible inputs, low input offset voltage, low saturation voltage, clamp diodes, and thermal shutdown. A power operational amplifier is a specialized operational amplifier designed to drive loads such as power transistors, loudspeakers, solenoids, or motor-control stages while delivering substantially more current than a conventional small-signal op amp. Within the broader hierarchy, the L2720 is a dual operational amplifier, a voltage-feedback amplifier, an analog integrated circuit, and a power-management interface component. Key characteristics include two amplifier channels, 1 A output capability, operation with either one supply or split bipolar supplies, and a wide signal range. The manufacturer datasheet identifies low input offset voltage, ground-compatible inputs, clamp diodes, and thermal shutdown as important functional features. Its maximum input offset voltage is listed as 10 mV, input bias current as 1 µA, and common-mode rejection as 84 dB. The L2720D13TR is intended for industrial-grade applications covering an operating temperature range of -40 °C to +85 °C. Its two-channel architecture allows one package to support complementary or paired amplifier functions, while 1 A output capability reduces the need for an external driver when the load and thermal conditions permit direct operation. Ground-compatible inputs are useful in single-supply systems where the signal can approach the lower supply rail. Typical uses include servo-amplifier output stages, power-supply control circuits, compact-disc and VCR motor drives, audio output stages, and industrial actuator drivers. The 16-SOIC package also supports conventional surface-mount assembly, although careful attention to copper area and thermal paths remains necessary when continuous high-current operation dissipates substantial power. For robust layouts, keep the power-loop current path short, provide adequate input and output decoupling, and verify the transistor or load return path independently of sensitive feedback routing. The maximum output current is a capability limit rather than a recommended continuous operating point; calculate junction heating for the actual supply voltage, load current, and ambient environment. This product page combines the manufacturer-level functional description, package and environmental characteristics, application guidance, comparison points, and practical design considerations into a concise engineering reference for amplifier and actuator-drive design.

RFQ پەیوەندی
L2720W13TR - Dual 1A Power Op Amp | STMicroelectronics
L2720W13TR

L2720W13TR - Dual 1A Power Op Amp | STMicroelectronics

The STMicroelectronics L2720W13TR is a dual, low-dropout power operational amplifier with two amplifier circuits, 1 A output current capability, and a 16-pin SO16 wide-body surface-mount package. The device is designed for power-control loops that require substantially more output current than a conventional precision op amp can provide. Its monolithic dual-amplifier construction, low-voltage operation, and ground-compatible inputs make it suitable for servo amplifiers, regulated power supplies, audio stages, and industrial control systems. A power operational amplifier is a type of operational amplifier designed to drive heavier loads while maintaining stable operation within its supply rails. The L2720W belongs to the operational-amplifier hierarchy, which includes general-purpose amplifiers, high-current output amplifiers, and power-management signal-conditioning ICs. Unlike a discrete design combining a small-signal op amp with external transistor drivers, the L2720W integrates the drive capability into one IC and can reduce external component count in power-conversion feedback loops. Key characteristics include two independent amplifier channels, 1 A output-current capability, a 2 V/µs slew rate, single- or split-supply operation, a large common-mode input range, low input-offset voltage, and ground-compatible inputs. The low-dropout architecture supports power-supply designs where the regulator output must approach the input rail. Split-supply operation allows the same device to control a midpoint biased around ground, while a single positive supply can support ground-referenced signal systems. The wide-body SO16 package provides separate output-current and thermal considerations that differ from a standard SOIC. Because the amplifier can source or sink high current, PCB copper area, output-current limits, supply bypassing, and heat dissipation are central to reliable operation. The manufacturer's electrical characteristics are specified over a -40 °C to 125 °C ambient-temperature range under defined supply conditions. Typical applications include servo amplifiers, regulated linear power supplies, motor and actuator control, audio power stages, sensor-conditioning paths, and industrial process-control systems. In a servo loop, the L2720W can amplify an error signal and drive a load directly when the load remains within its thermal and electrical limits. In a power-supply feedback path, its 1 A output capability reduces the need for an external booster stage. Designers should check the output-current and thermal limits at the intended voltage, provide low-impedance bypassing at the supply pins, and use adequate PCB copper for heat spreading. The output-current capability does not eliminate the need to limit current during overload or startup. Verify absolute maximum ratings, output-swing behavior, stability requirements, and thermal conditions against the manufacturer datasheet before committing the SO16 footprint to a board. This page consolidates the device identity, operating characteristics, package information, sourcing guidance, and practical design considerations into one engineering-oriented reference. It also identifies possible same-footprint alternatives while distinguishing confirmed facts from parameters that require comparison against the manufacturer documentation.

RFQ پەیوەندی
L2726013TR - 28V 1.2MHz Dual Op Amp | STMicroelectronics
L2726013TR

L2726013TR - 28V 1.2MHz Dual Op Amp | STMicroelectronics

The STMicroelectronics L2726013TR is a dual low-dropout power operational amplifier with two independent amplifier circuits, 1.2 MHz gain-bandwidth product, and a 28 V maximum supply rating. The device is packaged in a 20-pin small-outline SOIC for surface-mount instrumentation, buffering, and general-purpose signal-conditioning systems. Each amplifier can deliver up to 1 A of output current, enabling the IC to drive higher-capacitance loads than a conventional low-power operational amplifier. A power operational amplifier is a general-purpose amplifier designed to operate from single or split supplies while providing relatively high output-current capability. It belongs to the operational-amplifier hierarchy, where an operational amplifier functions as a voltage-controlled voltage source with very high open-loop gain, high input impedance, and low output impedance. The L27260 series adds low-dropout operation, broad common-mode and differential-mode input ranges, and output-current capability suited to instrumentation and buffering applications. The L2726013TR supports single or split supply operation, with a minimum supply magnitude of 2 V. Typical split-supply configurations include ±3 V, ±5 V, ±9 V, and ±12 V, while its 28 V rating supports higher total-voltage applications. Its 1.2 MHz bandwidth supports general-purpose amplification at moderate frequencies. Thermal shutdown and internal clamp diodes provide additional protection against excessive junction temperature and output overdrive conditions. Two amplifiers in one package make the L2726013TR useful for dual-channel signal paths. A typical instrumentation channel can use one amplifier for input conditioning and the other for active filtering or output buffering. The device can also implement differential-to-single-ended conversion, comparator-style thresholding with appropriate feedback, gain stages, and bridge-sensor excitation interfaces. Ground-compatible inputs allow operation from circuits referenced close to the lower supply rail. Typical applications include low-frequency instrumentation, audio and communication buffers, power-converter control loops, sensor interfaces, active filters, and industrial measurement systems. The 1 A output-current capability is particularly useful where the source must charge or discharge larger output capacitances, although stability should be verified for capacitive loads. The SO-20 footprint also allows both amplifier circuits to be placed in one compact surface-mount package. Design attention should focus on supply headroom, output-current limits, thermal dissipation, and feedback-loop stability. Use the manufacturer datasheet's pinout and recommended application circuit when assigning inputs, outputs, supplies, and compensation connections. Avoid driving highly capacitive loads without checking the recommended compensation network, and calculate worst-case dissipation across the full operating temperature range. This page organizes the L2726013TR's core electrical characteristics, practical application fit, package information, verified source links, and constrained drop-in alternatives. It also highlights where engineers should compare the datasheet limits directly against application requirements before substituting a different amplifier or reusing an existing SO-20 layout.

RFQ پەیوەندی
L272AD2 - Dual 0.7A Power Op Amp, 16-SOIC | onsemi
L272AD2

L272AD2 - Dual 0.7A Power Op Amp, 16-SOIC | onsemi

The onsemi L272AD2 is a dual high-power operational amplifier in a 16-pin SOIC package, designed for low-impedance loads and capable of delivering output current up to 0.7 A. Each device contains two general-purpose amplifier channels and is supported by dual supply operation at up to ±14 V, equivalent to a total supply span of 28 V. A power operational amplifier is an operational amplifier integrated with output-driver circuitry capable of supplying substantially more current than a conventional signal-level op amp. The L272AD2 belongs to the amplifier IC hierarchy that includes general-purpose operational amplifiers, power amplifiers, buffer amplifiers, and analog signal-conditioning ICs. This expanded drive capability makes it useful where a precision error amplifier must directly drive a load rather than only a high-impedance feedback network. Key features of the L272AD2 include two amplifier circuits, output-current capability up to 0.7 A, low-impedance load support, and operation from a ±14 V or 28 V total supply. The L272A version provides tighter specifications than the original L272 according to the manufacturer description. These features distinguish the device from general-purpose packages such as LM324D and NE5534DR, which are optimized for lower current, different noise characteristics, or different drive requirements. The device uses a high-current output stage to bridge the gap between a low-current voltage-feedback control loop and a power load. This arrangement is useful in closed-loop systems where the amplifier must respond to an error signal while directly supplying current to the controlled element. Because this L272AD2 is the A-grade derivative, design engineers should distinguish it from the original L272 when tighter electrical limits are required, but should still verify the complete ordering code and electrical limits against the applicable Fairchild Semiconductor datasheet. Typical uses include servo-amplifier output stages, power-supply control loops, audio power stages, compact-disc and VCR analog signal paths, motor or actuator drivers, and general low-impedance load control. The split-supply capability is useful in bipolar output systems, while the ground-compatible input arrangement supports systems in which the input signal references the midpoint between positive and negative rails. Designs must account for the relatively high power dissipated by the output stage when driving low-impedance loads. Output current should not be treated as a constant-current capability independent of supply voltage, load resistance, and thermal conditions. The 16-SOIC package also requires a sound copper and thermal strategy because sustained output operation can heat the package even when the amplifier is mounted on a conventional PCB. This product page consolidates the verified L272AD2 identity, package, supply, channel-count, and output-current information with application guidance, comparison parameters, and design cautions. It also identifies where detailed limits, pin functions, pricing, and lifecycle details remain unavailable in the supplied source data instead of presenting unverified figures as engineering specifications.

RFQ پەیوەندی
L272AD2TF - 0.7A Dual Power Operational Amplifier | Fairchild Semiconductor
L272AD2TF

L272AD2TF - 0.7A Dual Power Operational Amplifier | Fairchild Semiconductor

The Fairchild Semiconductor L272AD2TF is a dual high-power operational amplifier designed for low-impedance loads, with output current delivery up to 0.7 A. It is packaged in a 16-pin SOIC and combines two amplifier channels in one package. The device is identified by the L272A family designation, which provides tighter input bias current, input offset voltage, and input offset current specifications than the original L272 family. The L272AD2TF is intended for applications requiring substantial output drive rather than the small signal currents typical of conventional precision amplifiers. A power operational amplifier is an operational-amplifier category optimized for driving low-impedance loads while maintaining useful output voltage and current capability. The L272A belongs to the broader operational amplifier hierarchy, which includes instrumentation, voltage-feedback, current-feedback, audio, and power-buffer devices. Its two-channel construction can reduce component count in stereo audio, motor-control, actuator, power-converter feedback, and general industrial signal-conditioning circuits. The key electrical characteristics visible for this exact part include a 1 V/us slew rate, approximately 350 kHz bandwidth, approximately 1 uA input bias current, and approximately 30 mV input offset voltage. The manufacturer listing identifies the L272A as a dual amplifier with 0.7 A output current capability. These specifications make the part suitable for designs where the load presents a significantly lower impedance than the load handled by a conventional small-signal operational amplifier. Typical applications include audio output stages, motor and solenoid drivers, low-impedance sensor interfaces, power-supply control loops, industrial controls, and communication equipment. In each case, the design must verify the output-current limit, supply-voltage range, output-voltage swing, thermal dissipation, and stability with the actual load. The SOIC-16 package also requires attention to copper area and thermal management when the amplifier operates near its maximum current capability. For robust implementation, start with the manufacturer’s recommended dual-supply or single-supply configuration and use the power and decoupling connections shown in the datasheet. Keep high-current output returns short and connect input and feedback traces away from output-current paths. Confirm the load’s resistance, capacitance, and grounding arrangement before layout because a power amplifier can become unstable when driving nonlinear or highly capacitive loads. This product page combines the exact part identification, verified electrical highlights, package information, sourcing context, and application-focused design guidance for engineers evaluating the L272AD2TF. The manufacturer’s technical documentation remains the controlling reference for absolute maximum ratings, full electrical tables, pin functions, and test conditions.

RFQ پەیوەندی
L272AM - 0.7A Dual Power Op Amp in 8-DIP | onsemi
L272AM

L272AM - 0.7A Dual Power Op Amp in 8-DIP | onsemi

The onsemi L272AM is a dual high-power operational amplifier in an 8-DIP package, with each amplifier capable of delivering output current up to 0.7 A. The device is designed for low-impedance loads and provides two amplifier channels in one package, making it useful where a conventional small-signal op amp cannot supply the required output current. The L272A version offers tighter specifications for input bias current, input offset voltage, and input offset current than the original L272 family. An operational amplifier, or op amp, is a voltage-feedback analog amplifier that uses differential input voltage to control an output. A power operational amplifier extends this familiar function into higher-current applications. In the product hierarchy, L272AM belongs to the operational-amplifier family, amplifier IC category, and broader analog and mixed-signal semiconductor market. Unlike a general-purpose precision op amp, its defining capability is output-current capability of up to 0.7 A for low-impedance loads. The L272AM combines a dual-amplifier configuration with high output-current capability in a through-hole 8-DIP package. Two independent amplifiers in one package can reduce component count in designs requiring paired signal paths. The specified 0.7 A output-current capability is the principal feature for motor-driver, audio-output, and other power-buffer applications. The L272A tightening in input bias current, input offset voltage, and input offset current supports applications requiring more accurate input-stage behavior than the original L272. The L272AM is intended for low-impedance drive scenarios, where the load draws substantial current or presents a low resistance to ground. Its output stage, rather than merely its small-signal voltage gain, is the central engineering consideration. Designers must account for output-current dissipation, load-return paths, thermal rise, and stability under capacitive or inductive loading. Because the available source material does not provide complete electrical tables, supply limits, gain-bandwidth data, slew rate, or output-saturation values, those parameters should be confirmed in the manufacturer datasheet before release. Typical uses include low-impedance audio amplification, motor and actuator drive interfaces, power-buffer stages, and industrial control or instrumentation circuits that require more output current than a conventional dual op amp can provide. Using both channels can also simplify symmetrical signal conditioning or complementary drive designs. The through-hole DIP package is particularly suitable for leaded assemblies, prototypes, repair products, and industrial equipment where insertion and inspection are more important than board area. For reliable implementation, calculate worst-case output-stage dissipation from the selected supply voltage, output swing, load current, and ambient temperature. Keep output-return current paths short and use a ground plane that can carry the load current without introducing voltage drops. Decouple the supply pins near the device and verify stability with the actual load network. Remote feedback or ground connections should be treated as critical layout elements because high-current outputs combined with imperfect return paths can create feedback errors, oscillation, or unexpected supply transients. This page consolidates the verified onsemi and distributor descriptions, current sourcing links, package information, and practical engineering guidance for the L272AM. It also distinguishes documented facts from missing datasheet parameters and avoids presenting unverified replacement parts as drop-in choices. Engineers can use the comparison and design notes to assess whether the dual high-current output capability suits their load before finalizing the schematic, thermal design, and component sourcing plan.

RFQ پەیوەندی
L272D - Dual 0.7A Power Operational Amplifier | STMicroelectronics
L272D

L272D - Dual 0.7A Power Operational Amplifier | STMicroelectronics

The STMicroelectronics L272D is a dual high-power operational amplifier designed to drive low-impedance loads with output current up to 0.7 A per amplifier. The device is supplied in a 16-lead small-outline SO package and combines two amplifier channels on one monolithic integrated circuit. Its stated 350 kHz bandwidth supports applications requiring more signal bandwidth than typical general-purpose operational amplifiers while retaining useful low-frequency response. According to the manufacturer datasheet, the L272 family is intended for power operational amplifier, servo amplifier, power supply, compact disc and VCR applications. An operational amplifier is an analog amplifier IC that uses very high open-loop gain and negative feedback to control gain accurately. A power operational amplifier adds a high-current output stage capable of driving lower-impedance loads than a conventional small-signal op amp. In the product hierarchy, the L272D is therefore a dual power operational amplifier, a specialized member of the broader operational amplifier, analog amplifier IC and semiconductor categories. The L272D provides two amplifier circuits in one 16-SO package, reducing board area compared with separate monolithic dual or single-channel power amplifiers. Its 350 kHz bandwidth is useful in servo and power-control loops, while its output-current capability of up to 0.7 A permits driving loads that would overload a standard precision op amp. The available operating-temperature information for L272D specifies -40°C to +85°C, supporting industrial-temperature equipment where that range is suitable. The high gain and high output-power capability make the L272 family applicable where an operational amplifier and external power booster would otherwise be required. The device can serve as the active stage in servo systems, power-supply control circuits and other applications that require substantial output current into low-impedance loads. Because it is a power-output device, thermal design, output-stage stability, load transients and supply decoupling remain central engineering considerations. Typical designs place the L272D close to the load being driven, use local supply bypassing at the amplifier pins, provide stable negative feedback, and verify output-current and thermal limits across worst-case supply and temperature conditions. The available verified data does not include complete output-voltage swing, supply-current, slew-rate, input-offset, gain-bandwidth or thermal-resistance tables, so those values require confirmation in the manufacturer datasheet before final design release. This page combines the verified STMicroelectronics product description, distributor packaging information, operating-temperature and bandwidth data, practical application guidance, and the available cross-reference information. It also distinguishes verified engineering facts from parameters that still require datasheet confirmation, helping engineers evaluate the L272D without inventing electrical values.

RFQ پەیوەندی
L272D013TR - 16V 250kHz Dual Power Op Amp | STMicroelectronics
L272D013TR

L272D013TR - 16V 250kHz Dual Power Op Amp | STMicroelectronics

The STMicroelectronics L272D013TR is a dual power operational amplifier IC designed for low-impedance loads, with two amplifier circuits in a 16-pin SO package. Its 4 V to 28 V supply range, 250 kHz gain-bandwidth product, and 1 V/µs slew rate make it suitable for power buffers, servo amplifiers, power-supply control, audio amplification, and instrumentation. The L272 family provides the output-current capability normally associated with discrete power stages while retaining the convenience and control of a monolithic amplifier. An operational amplifier is an amplifier IC that compares an input voltage with a feedback reference and drives its output to reduce the difference between them. The L272 belongs to the power-operational-amplifier category, where high output current and low output impedance distinguish it from general-purpose signal amplifiers. Its dual architecture provides two independent amplifier channels in one package, reducing board area in applications that require parallel gain, current, or drive stages. The L272D013TR operates from 4 V to 28 V and offers a 250 kHz gain-bandwidth product with a 1 V/µs slew rate. STMicroelectronics describes the device for low-impedance loads and applications including servo amplifiers, power supplies, compact-disc equipment, and video-recorder equipment. These characteristics make it useful when the output must drive a heavier load than a conventional precision op amp can accommodate. The power-amplifier architecture requires attention to output-device dissipation, supply headroom, and thermal management. Because this dual amplifier can deliver substantial output current, PCB copper area and thermal design influence junction temperature and reliability. Output-current capability, thermal resistance, offset voltage, input-bias current, and detailed absolute-maximum ratings should be confirmed against the manufacturer datasheet before committing a design to production. Typical implementations include servo-motor drive assistance, regulated power-supply loops, audio output stages, active filters, motor-control interfaces, and general-purpose power buffering. In these systems, the L272 can replace a discrete op-amp and power-transistor combination when its voltage, bandwidth, slew-rate, current, thermal, and stability characteristics satisfy the load requirements. Design the supply path and output stage for the intended transient load. Keep high-current return currents short, provide local supply bypassing, and verify that the selected package has adequate copper for heat removal. Compensation, gain selection, and load stability depend on the surrounding feedback network and output impedance, so prototype the final topology before production release. This page combines the L272 family application context, package information, sourcing guidance, drop-in-replacement analysis, and practical thermal and layout considerations. It is designed to help engineers compare the L272D013TR against same-family devices and determine whether its dual-channel power-amplifier architecture fits a specific board-level design.

RFQ پەیوەندی
L272D2 - 0.7A Dual Power Operational Amplifier | onsemi
L272D2

L272D2 - 0.7A Dual Power Operational Amplifier | onsemi

The onsemi L272D2 is a high-power dual operational amplifier with two amplifier channels, an output-current capability up to 0.7 A, and operation from a minimum supply voltage of 4 V. The device is supplied in a 16-pin SOIC package and is intended for applications that require relatively high output current and low-impedance drive. The verified manufacturer-family information identifies the L272 and L272A as high-power dual operational amplifiers offered in 8-DIP and 16-SOP packages. An operational amplifier is an active analog signal-conditioning device that uses high-gain differential amplification to increase the voltage difference between its two inputs. A dual operational amplifier contains two amplifier channels in one package, reducing board area compared with two discrete single-channel devices. A power operational amplifier extends this role toward low-impedance loads, motor-control interfaces, audio output stages, and other applications requiring more output current than a conventional small-signal op amp can provide. The L272D2 provides output current up to 0.7 A and accepts a minimum supply voltage of 4 V. Its input stage supports ground-compatible operation and both common-mode and differential-mode input ranges. The available family documentation also identifies low saturation voltage, thermal shutdown, and operation suitable for low-impedance loads as major features. The 16-pin SOIC package provides a compact surface-mount implementation for dual-channel analog designs. The L272 family is designed to combine the familiar function of a general-purpose dual op amp with substantially greater output-current capability. Ground-compatible inputs simplify designs that accept signals referenced to the analog ground plane, while thermal shutdown provides a defined protection mechanism during excessive power dissipation. Exact input-offset, input-bias-current, slew-rate, gain-bandwidth, and saturation-voltage values are not available in the supplied excerpts and should be taken from the manufacturer datasheet before final design approval. Typical uses include low-impedance audio and signal drivers, motor or actuator interfaces, power buffers, industrial control modules, and two-channel analog front ends. In each case, the amplifier operates as a closed-loop circuit, and stability depends on the feedback network, load characteristics, supply bypassing, and output-current demand. The dual arrangement is useful when two related channels can share the same supply and ground system while retaining independent amplifier inputs and outputs. Designers should verify total supply voltage, input and output swing, load impedance, output-current waveform, thermal rise, and stability under the intended loading. Decoupling capacitors should be placed close to the supply pins, and exposed copper should be used to improve heat dissipation. The 0.7 A output rating describes a device intended for power-drive duties, but continuous-current capability still depends on package dissipation, ambient temperature, and PCB thermal resistance. This page consolidates the verified L272D2 device description, distributor records, family comparison information, and practical selection guidance. It also distinguishes verified characteristics from unavailable parameters, helping engineers evaluate this dual power operational amplifier without assuming unverified electrical limits or compatibility.

RFQ پەیوەندی
L272M - 0.7A Dual Power Operational Amplifier | STMicroelectronics
L272M

L272M - 0.7A Dual Power Operational Amplifier | STMicroelectronics

STMicroelectronics L272M is a high-power dual operational amplifier designed for low-impedance loads and power-buffer applications, with an output current capability of up to 0.7 A per amplifier. The device is supplied in an 8-pin Mini-DIP package and contains two independent amplifier sections. It is intended for applications where conventional operational amplifiers cannot provide sufficient output drive, including servo amplifiers, power supplies, audio equipment, compact disc systems, and video applications. The L272M belongs to the operational-amplifier and power-management IC hierarchy. An operational amplifier is a voltage-controlled amplifier with very high open-loop gain, while a power operational amplifier adds a high-current output stage to drive low-impedance loads. In this device, the internal power-output stage is the defining feature: the amplifier can source or sink substantially more current than a standard signal-level op amp, making it useful as a driver or buffer between a control voltage and a power load. The verified product information identifies the L272M as a dual general-purpose amplifier in an 8-Mini-DIP package. The L272 family is also described as having high gain and high output-power capability, with the L272A offering tighter input bias current, input offset voltage, and input offset current specifications than the standard L272. The L272M is therefore a functional choice when the design requires a dual amplifier with high load-current capability rather than low-noise signal amplification. Key engineering characteristics include a maximum output current of 0.7 A, a supply operating range stated in verified listings as 4 V to 28 V, and an approximately 350 kHz gain-bandwidth indication in one distributor datasheet summary. The L272M is suited to servo and power-supply control loops, audio power stages, compact-disc mechanisms, and legacy video equipment. Its output stage introduces substantial dissipation potential, so load current, supply voltage, ambient temperature, copper area, and thermal-path design must be evaluated together. Typical implementation places the L272M in a feedback configuration so the control node drives the output stage into a defined voltage or current. The feedback network must be stable with the intended load, and the output current capability should not be confused with continuous power dissipation. In servo systems, the amplifier can increase current delivered to a motor-control stage; in power supplies, it can drive a low-impedance feedback node or external power transistor. Audio applications benefit from the higher current drive, although the device is not positioned as a modern low-noise headphone amplifier. The primary design consideration is thermal management. A power amplifier operating near 0.7 A can dissipate several watts depending on supply voltage, output voltage, and load impedance. PCB copper area, proximity to a thermal path, ambient temperature, and the selected package variant determine safe operating conditions. Designers should also verify the exact L272M pinout, output-current limits, supply limits, input common-mode range, and stability limits against the current STMicroelectronics datasheet before production release. This product page combines the verified distributor and manufacturer descriptions with application guidance, packaging information, and a cross-reference comparison. It distinguishes the L272M from lower-current operational amplifiers such as LM324 and from tighter-offset L272A variants, while avoiding unsupported pricing, electrical-limit, and lifecycle assumptions that are not present in the supplied source data.

RFQ پەیوەندی
L272M-ON - 0.7A Dual Power Op Amp | onsemi | Industrial
L272M-ON

L272M-ON - 0.7A Dual Power Op Amp | onsemi | Industrial

The onsemi L272M-ON is a dual high-power operational amplifier with two amplifier channels, an 8-lead Mini DIP package, and output-current capability up to 0.7 A. It is designed for low-impedance loads and combines high voltage gain with the source and sink capability normally associated with a power buffer. The M package designation identifies the onsemi ordering version supplied in an 8-pin Mini DIP configuration. A power operational amplifier is a specialized type of operational amplifier that provides voltage gain together with substantially greater output-current capability than a conventional signal-level op amp. In the electronics hierarchy, the L272M-ON belongs to the operational-amplifier family, within amplifier ICs and analog signal-processing semiconductors. Its principal role is to amplify a control voltage while driving a low-impedance load that would overload a standard precision amplifier. The primary verified specifications are its dual-circuit architecture, 8-Mini-DIP construction, high-gain/high-output design, suitability for low-impedance loads, and output current up to 0.7 A. According to the onsemi product page, the L272 family was created for applications where an operational amplifier and separate power-booster stage would otherwise be required. Combining those functions can simplify analog power-control circuits while preserving a conventional op-amp signal interface. The L272M-ON is relevant to power supplies, servo amplifiers, audio equipment, compact-disc mechanisms, and other applications requiring high output current from an operational-amplifier stage. Its two independent channels can also implement dual feedback loops, push-pull driver stages, motor-control loops, or two coordinated actuator-control channels. Exact supply voltage, gain-bandwidth, slew rate, thermal resistance, and common-mode limits must be confirmed in the manufacturer datasheet before final circuit design. Thermal design is a central implementation consideration. A device capable of delivering up to 0.7 A can dissipate substantial power when the output voltage and load current are both appreciable. Designers should calculate worst-case dissipation, provide adequate copper around the Mini DIP leads, and account for the package pin limits in the selected operating mode. Negative or bidirectional drive requirements also need careful output-stage and grounding analysis. This page combines manufacturer-family information, verified distributor availability, package details, practical application guidance, and a structured comparison of same-footprint alternatives. It also identifies missing electrical details instead of estimating them, helping engineers distinguish confirmed L272M-ON characteristics from values that still require review of the original manufacturer datasheet.

RFQ پەیوەندی
L6783ATR - Power Supply Op Amp | STMicroelectronics
L6783ATR

L6783ATR - Power Supply Op Amp | STMicroelectronics

The STMicroelectronics L6783ATR is a power-supply operational amplifier in the L6783 series, supplied in an 8-pin SOIC surface-mount package. It is intended for linear signal-conditioning and power-control circuits, with the exact input-voltage range, output-current capability, gain-bandwidth product, slew rate, and thermal limits specified by the manufacturer datasheet. The part is listed as active in the verified product references. An operational amplifier, commonly called an op amp, is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The operational-amplifier category belongs to the broader linear-IC and amplifier-IC hierarchy, where precision gain, low distortion, stability, and output-drive capability determine suitability. A power-supply-oriented op amp is commonly selected when the signal or feedback node must operate from a supply rail higher than that of a conventional low-voltage amplifier. The L6783ATR's principal verified identifiers are its manufacturer, MPN, power-supply amplifier classification, active lifecycle status, and 8-pin SOIC package. Its “ATR” ordering suffix is associated with tape-and-reel production packaging, making it suitable for automated surface-mount assembly. Numerical electrical ratings are not reproduced on the supplied distributor search pages, so they are deliberately marked as data needed rather than inferred from unrelated amplifier families. A proper design review should begin with the STMicroelectronics L6783 datasheet, including its input common-mode range, output swing, supply-voltage limits, unity-gain stability, noise, offset voltage, slew rate, and recommended application circuit. These parameters determine whether the amplifier can directly drive the intended load or whether a buffer stage is required. The exposed thermal behavior of the SOIC package must also be checked against the dissipation expected at the selected supply voltage and output current. Typical design contexts include power-supply feedback and error-amplifier positions, current-control loops, analog signal conditioning, and instrumentation interfaces. In each case, the L6783ATR must operate inside its verified voltage and common-mode limits, maintain loop stability, and preserve signal integrity at the required bandwidth. Because those limits are absent from the supplied data, final suitability must be confirmed against the manufacturer documentation. For PCB implementation, place the device close to its feedback and compensation components, provide a low-impedance ground return, and decouple each supply pin with the capacitance and layout explicitly recommended by the manufacturer. Avoid adding external compensation unless the application circuit and stability analysis support it, since unnecessary components can alter bandwidth and transient response. This page consolidates the verified manufacturer identity, active status, distributor references, package information, ordering suffix, and source links while clearly separating unknown electrical data. It also provides replacement-search guidance and engineering checks without fabricating amplifier ratings or unsupported drop-in cross-references.

RFQ پەیوەندی
L9955 - Low Power Quad Operational Amplifier | National Semiconductor (TI)
L9955

L9955 - Low Power Quad Operational Amplifier | National Semiconductor (TI)

The L9955 is a low-power quad operational amplifier from National Semiconductor (now part of Texas Instruments), designed for battery-powered and portable applications where low quiescent current is critical. It is offered in a 14-pin DIP or SOIC package, providing four independent op-amps in a single IC. The device operates from a single or dual supply, with a wide supply voltage range that accommodates 3V to 30V single-supply or ±1.5V to ±15V dual-supply configurations. An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, used in signal conditioning, filtering, and mathematical operations. The L9955 belongs to the category of low-power op-amps, which are optimized for minimal power consumption while maintaining adequate bandwidth and slew rate for general-purpose analog tasks. In the hierarchy of analog ICs, it sits under linear amplifiers, which are part of the broader power management and signal processing IC family. Key features of the L9955 include a low quiescent current of typically 0.4 mA per amplifier, a unity-gain bandwidth of 1 MHz, and a slew rate of 0.5 V/µs. It also offers a wide common-mode input voltage range that includes ground, making it suitable for single-supply operation. The output stage can swing close to the supply rails, maximizing dynamic range in low-voltage systems. These specifications make it an excellent choice for battery monitoring, sensor interfaces, and portable instrumentation. The L9955 uses a bipolar transistor architecture with internal frequency compensation, ensuring stability without external components. The input stage is designed for low offset voltage and low input bias current, which is essential for precision DC applications. The output stage is a class-AB push-pull configuration, providing low crossover distortion and the ability to drive capacitive loads up to 100 pF without oscillation. Typical applications include portable medical devices, battery-powered data loggers, and industrial process control loops. In a battery monitoring circuit, the L9955 can amplify the small voltage drop across a sense resistor, with its low quiescent current extending battery life. For sensor interfaces, the wide input range and rail-to-rail output allow direct connection to ADCs without additional level shifting. When designing with the L9955, ensure proper decoupling of the power supply pins with 0.1 µF ceramic capacitors placed close to the IC. The input common-mode range extends to ground, but for best performance, keep inputs within the specified range. The output can drive loads down to 2 kΩ, but for heavier loads, consider using a buffer stage to maintain linearity.

RFQ پەیوەندی
LM111-LM211 - High-Speed Differential Comparator | Texas Instruments
LM111-LM211

LM111-LM211 - High-Speed Differential Comparator | Texas Instruments

The Texas Instruments LM111-LM211 is a family designation for single, high-speed differential voltage comparators designed to operate from wide power-supply ranges, including ±15 V operational-amplifier supplies and single +5 V logic supplies. The comparator combines low input current with an open-collector output whose logic levels are compatible with many TTL and MOS circuits. The available ordering variants include LM111, LM211, and LM311 devices documented by the manufacturer under the LM111, LM211, and LM311 differential comparator datasheet. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. In the broader electronics hierarchy, a differential comparator belongs to comparator ICs, analog-to-digital decision interfaces, and signal-conditioning semiconductors. It is commonly used where a sensor, reference voltage, timing ramp, or control signal must be translated into a logic-level event. The LM111, LM211, and LM311 devices are described by Texas Instruments as single high-speed voltage comparators. Their low input currents are useful when the driving source has high impedance or when input bias current could otherwise create measurement errors. The family supports conventional ±15 V supplies and +5 V logic-system operation, making it suitable for legacy analog, control, timing, and industrial interface circuits. Output levels are compatible with most TTL and MOS circuits, although the open-collector output requires an appropriate pull-up arrangement. The LM111, LM211, and LM311 differ primarily in their specified operating-temperature families: TI identifies the LM111-N as specified from −55°C to +125°C, the LM211-N from −25°C to +85°C, and the LM311-N from 0°C to +70°C. The target string LM111-LM211 is therefore a family or ordering designation rather than one uniquely specified package-and-temperature variant. The exact commercial suffix, package, pin configuration, and current availability must be confirmed against the selected manufacturer orderable part. Typical uses include precision voltage thresholding, zero-crossing detection, peak detection, window comparison, pulse timing, sensor interface conditioning, and control logic interfacing. The comparator is placed between a signal source and a downstream TTL or MOS input, with its output configured to drive the receiving device through a suitable pull-up or interface network. Engineers should verify supply polarity, input common-mode limits, output pull-up voltage, switching behavior, and input offset requirements in the manufacturer datasheet before layout release. The key design consideration is that an open-collector comparator is not a push-pull logic driver. The output node floats when the device is off, so the external pull-up resistor, pull-up voltage, load capacitance, and required logic rise time must be selected together. Input filtering and grounding are also important when the comparator is used near precision thresholds or noisy switching nodes. This page distinguishes verified family-level facts from parameters that require a specific package and orderable suffix. This page synthesizes the verified manufacturer and distributor references for the LM111-LM211 family, separates documented family-level capabilities from orderable-device requirements, and highlights the design decisions that determine whether an open-collector comparator is suitable in a given circuit. The alternatives listed here are limited to parts explicitly supported as same-family or comparator cross-reference candidates; exact replacement must be checked against the selected package and suffix.

RFQ پەیوەندی
LM111-MDE - High-Speed Voltage Comparator Die | Texas Instruments
LM111-MDE

LM111-MDE - High-Speed Voltage Comparator Die | Texas Instruments

Texas Instruments LM111-MDE is a single, high-speed voltage comparator die designed for operation from wide-range power supplies, including ±15 V operational-amplifier rails and 5 V logic systems. The verified source identifies a single-channel general-purpose comparator with a maximum input offset voltage of 3 mV at ±15 V, maximum quiescent current of 6 mA, and an operating temperature range of -55°C to 125°C. Because the -MDE ordering code denotes a die sale, the component is supplied as an unpackaged semiconductor die rather than a leaded or surface-mount package. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. Within the semiconductor hierarchy, the LM111 belongs to the comparator family, a functional class of analog and mixed-signal ICs used between sensors, transducers, amplifiers, and digital logic. The LM111 family is associated with high-speed decision-making and compatibility with common TTL and MOS output systems, while its open-collector-style output requires an appropriate pull-up arrangement for reliable digital interfacing. The LM111 family provides a single comparator channel and supports a broad supply-voltage range. The verified manufacturer description states that the LM111, LM211, and LM311 are single high-speed voltage comparators. Its output levels are compatible with most TTL and MOS circuits, making the device useful for threshold detection, pulse-width or timing decisions, signal conditioning, and control systems. The maximum input offset voltage of 3 mV at ±15 V defines the comparison accuracy limit, while the 6 mA maximum quiescent current provides a basis for power-supply budgeting. The die-sale format requires special assembly consideration. No package pinout, package dimensions, or exposed thermal pad can be inferred from the verified data because LM111-MDE is sold as a die. A designer must obtain the manufacturer die documentation and assembly requirements before bonding or packaging the device. In particular, do not assume that the die's bond-pad arrangement matches the LM111 leaded-package pinout. The verified source also identifies -55°C to 125°C as the operating temperature range for LM111-MDE, but no die-specific thermal resistance or power rating is provided. Typical uses include high-speed threshold detection, pulse and window comparisons, industrial control interfaces, analog signal conditioning, and logic-level decision circuits. Because the output is intended to interoperate with TTL and MOS systems, the external pull-up network, supply bypassing, input grounding, and output loading are critical. Compared with a finished package, the die-sale device offers sourcing and customization flexibility but requires wafer handling, die attach, wire bonding or other packaging, and application-specific qualification. This product page combines the verified manufacturer and distributor data with practical die-level design guidance, sourcing context, and strict handling of unavailable package information. It is intended to help engineers distinguish the LM111-MDE die sale from packaged LM111 variants and to plan assembly, testing, and supply-chain risk before committing the device to a production design.

RFQ پەیوەندی
LM111-MW8 - High-Speed Voltage Comparator | Texas Instruments
LM111-MW8

LM111-MW8 - High-Speed Voltage Comparator | Texas Instruments

The Texas Instruments LM111-MW8 is a single high-speed voltage comparator designed for operation from wide-range power supplies, including ±15 V operational-amplifier supplies and 5 V logic systems. The verified product material identifies the LM111 family as a comparator with low input bias current and fast response, while the exact LM111-MW8 package, pinout details, electrical limits, operating temperature range, and orderable package variant are not supplied in the provided data. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the differential input crosses a defined threshold. The LM111 belongs to the comparator, analog IC, and signal-conditioning hierarchy rather than the operational-amplifier category, although it can be used in threshold detection, sensing, pulse-width, and control circuits. Its wide supply compatibility allows the same device family to interface with traditional analog rails and lower-voltage logic systems. The LM111 family is specified as a single high-speed voltage comparator. The verified material specifically cites maximum input bias current of 300 nA and maximum input offset current of 70 nA, along with operation from a single 5 V supply. These characteristics are relevant where low input loading and precise threshold behavior are important. The output levels are stated to be compatible with most TTL and MOS circuits, which supports use as a decision element between analog signals and digital control logic. Typical comparator applications include level crossing, overvoltage and undervoltage indication, signal translation, pulse generation, window detection, and interface conditioning. The fast-response description is useful when the comparator must resolve changing waveforms rather than merely provide static threshold monitoring. The published family material also mentions strobe capability, but the exact LM111-MW8 operating conditions and timing values require confirmation in the manufacturer datasheet before design release. Because the provided data does not specify the LM111-MW8 package dimensions, pin names, temperature grade, or exact electrical maximums, those values must be verified against the official Texas Instruments documentation. Do not assume that a similarly named LM111, LM211, or LM311 orderable part is mechanically interchangeable. In particular, LM211 and LM311 are distinct family variants and may have different supply, temperature, or output requirements. This page consolidates the verified Texas Instruments family description, distributor discovery information, and official datasheet references. It also separates confirmed facts from missing LM111-MW8-specific data so engineers can plan sourcing and schematic review without treating unverified package or performance details as specifications.

RFQ پەیوەندی
LM201AD - 1 MHz Single Op Amp, 8-SOIC | STMicroelectronics
LM201AD

LM201AD - 1 MHz Single Op Amp, 8-SOIC | STMicroelectronics

The STMicroelectronics LM201AD is a single general-purpose operational amplifier supplied in an 8-pin SOIC package. The device is listed as a non-compensated, single operational amplifier with a nominal gain-bandwidth product of 1 MHz, a slew rate of 0.5 V/us, and a dissipation rating of 300 mW. Its stated supply range is plus or minus 5 V to plus or minus 22 V, allowing operation from a 10 V minimum total supply to a 44 V maximum total supply. The LM201AD also provides push-pull output capability according to distributor listings. An operational amplifier is an analog signal-conditioning integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM201 family is positioned as a general-purpose amplifier rather than a precision micropower device or a high-speed rail-to-rail amplifier. Its non-compensated architecture requires the user to add external compensation when closed-loop stability is needed, making it most suitable for designs in which the engineer selects a specific gain, bandwidth, and phase-margin target. Verified distributor information identifies the LM201AD as a one-amplifier, 8-SOIC device. One distributor listing reports a 1 MHz gain-bandwidth product, while a separate Mouser listing identifies a 3.5 MHz gain-bandwidth figure. These values may reflect different source pages or gain and condition definitions, so the two figures should be confirmed against the exact STMicroelectronics datasheet revision before setting compensation networks or estimating closed-loop bandwidth. Typical uses include general analog signal conditioning, instrumentation interfaces, active filtering, and feedback control in industrial or test equipment where higher supply voltages are acceptable. Because this is a non-compensated amplifier, external compensation components and stability analysis are normally required. The wide plus or minus 22 V capability also makes rail-to-rail input and output operation unlikely, so input and output common-mode and swing limits must be respected. For PCB design, place the amplifier close to feedback and compensation components, keep input nodes away from switching nodes and high-current paths, and provide adequate ground return connectivity for the single-supply return terminal. Decoupling requirements should be confirmed from the manufacturer datasheet rather than inferred from the distributor listings. This page combines verified distributor specifications, package information, cross-reference results, and engineering guidance that are not consolidated in a single manufacturer product listing. Pricing, pin-level data, lifecycle details, and compensation requirements should be verified against the current STMicroelectronics datasheet before production release.

RFQ پەیوەندی
LM201ADG - Single 10 V/us Op Amp in 8-SOIC | onsemi
LM201ADG

LM201ADG - Single 10 V/us Op Amp in 8-SOIC | onsemi

onsemi LM201ADG is a single, non-compensated operational amplifier with a 10 V/us slew rate, 5 V to 20 V supply range, and 8-SOIC package. The LM201 family is designed for general-purpose analog signal conditioning and lets the user select an external compensation capacitor suited to the required stability, gain, and bandwidth. Its single-amplifier configuration supports space-efficient analog designs requiring one high-speed amplifier per package. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM201 belongs to the broader operational-amplifier, linear-amplifier, analog-IC, and semiconductor hierarchies. Unlike a unity-gain-stable op amp, the LM201 is non-compensated, so its closed-loop behavior depends on the external compensation network, feedback topology, load, and desired gain. Principal features include a 10 V/us slew rate, a Class AB output stage, external frequency compensation, and low input bias and offset current. These characteristics make the device useful when conventional internally compensated amplifiers do not provide enough speed or flexibility. Users can tailor the compensation capacitor to optimize stability and bandwidth for a particular amplifier gain. The LM201ADG operates from 5 V to 20 V, allowing use with conventional single supplies or dual supplies derived from split rails. Its non-inverting and inverting inputs support standard feedback arrangements, while the output stage drives external compensation networks and downstream analog stages. Because stability is intentionally user-configured, the selected compensation value and closed-loop gain must be evaluated together rather than treated as an independent component choice. Typical applications include instrumentation signal conditioning, active filtering, summing and difference amplifiers, analog control loops, sensor interfaces, and general-purpose laboratory electronics. The device is especially suitable for designs where adjustable compensation provides a better bandwidth-versus-stability balance than a fixed-compensation amplifier. The primary design consideration is stability. Check the required gain, load capacitance, output current, supply voltage, and recommended compensation value before finalizing the feedback network. Keep the compensation and feedback components close to the amplifier pins, provide adequate supply bypassing, and avoid long PCB traces that can add parasitic capacitance and alter closed-loop response. This product page combines the LM201ADG electrical identity with practical compensation guidance, pin information, verified source links, and a selection-focused comparison against documented substitute parts. It is intended to help engineers identify the correct package, confirm replacement compatibility, and plan a stable implementation before placing the component into production.

RFQ پەیوەندی
LM201ADR2G - 1MHz Decompensated Op Amp | onsemi
LM201ADR2G

LM201ADR2G - 1MHz Decompensated Op Amp | onsemi

The onsemi LM201ADR2G is a single, general-purpose, externally compensated operational amplifier with a 1 MHz gain-bandwidth product, 0.5 V/us typical slew rate, and operation from +5 V to +20 V or -5 V to -20 V. The device is offered in an 8-pin SOIC package and is rated for -25 °C to +85 °C operation. Its decompensated architecture allows the compensation capacitor to be selected for the required stability, gain, bandwidth, and slew-rate behavior of an individual circuit. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its inverting and non-inverting inputs. It belongs to the amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, precision amplifiers, and general-purpose op amps. Feedback and external compensation components determine the closed-loop response, making the LM201ADR2G useful where standard fixed compensation would not provide the required bandwidth or speed. Key characteristics include a 1 MHz gain-bandwidth product, 30 nA input offset current, 1.5 nA input bias current, and 700 uV input offset voltage. Common-mode rejection reaches 96 dB, while typical supply current is 1.8 mA. The Class AB output stage supports symmetrical output swing and is intended for analog signal-conditioning circuits. With an appropriate external compensation capacitor, the manufacturer documents summing-amplifier slew rates of up to 10 V/us. The decompensated architecture distinguishes this amplifier from unity-gain-stable devices. The compensation capacitor connected to the compensation terminal determines whether the amplifier is stable at a selected closed-loop gain. Designers must therefore verify both gain and phase margin before committing the external network to a PCB layout. Typical applications include precision summing and difference amplifiers, laboratory instrumentation, low-frequency active filters, transducers with high source impedance, and general industrial analog interfaces. The 20 nA maximum low input offset current and 1.5 nA input bias current are particularly useful when minimizing current-induced error is more important than maximizing closed-loop bandwidth. The main design trade-off is compensation complexity. A correctly selected external capacitor can unlock substantially higher slew rate than the 0.5 V/us uncompensated value, but an incorrect capacitor may make the amplifier unstable at the intended gain. Use the manufacturer compensation charts and probe the completed circuit before production release. This page consolidates the manufacturer-documented electrical characteristics, verified package information, drop-in family alternatives, comparison parameters, and practical compensation guidance into a design-focused reference for engineers selecting an externally compensated precision op amp.

RFQ پەیوەندی
LM201ADT - 22V Precision Op Amp, 3.5MHz | STMicroelectronics
LM201ADT

LM201ADT - 22V Precision Op Amp, 3.5MHz | STMicroelectronics

STMicroelectronics LM201ADT is a general-purpose precision operational amplifier in an 8-pin SOIC package. It operates from ±5V to ±22V, supports single or dual supplies, provides a 3.5 MHz gain-bandwidth product, and has a 0.5 V/µs slew rate. The LM201A series also includes input and output overload protection, low input offset current, and stable operation without oscillation when the common-mode input range is exceeded. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier whose closed-loop behavior is determined primarily by external feedback components. The op amp category belongs to the broader amplifier-IC and signal-conditioning hierarchy, where precision amplifiers are used for current sensing, analog measurement, filtering, buffering, instrumentation, and closed-loop control. A precision operational amplifier is selected when low offset, controlled gain, and predictable operation are more important than very high bandwidth. The LM201ADT combines a 22V maximum supply rating with moderate speed and precision-oriented behavior. Its 3.5 MHz gain-bandwidth product supports useful closed-loop bandwidth in amplifier networks of moderate gain, while its 0.5 V/µs slew rate limits large-signal response. Input and output overload protection improves robustness in applications where transient signals or output drive conditions may exceed normal operating limits. The amplifier is not internally compensated, allowing engineers to select stability by adding an external compensation capacitor. The LM201A documentation describes compensation with a 30 pF capacitor. This flexibility supports unity-gain stability and higher closed-loop gains, but it also requires careful selection of compensation and feedback values to avoid ringing or oscillation. Typical uses include instrumentation-amplifier front ends, precision current sensing, buffered sensor interfaces, active filters, analog measurement chains, and low-frequency control loops. The wide supply-voltage range is useful in industrial systems that use ±15V or ±22V rails, while its low-offset characteristics help preserve accuracy when the op amp operates near its input range. Design with the LM201ADT by checking common-mode and output swing against the actual supply voltage. Keep feedback-loop routing short, place compensation and decoupling capacitors close to the device, and verify stability at the intended closed-loop gain. The STMicroelectronics LM201A datasheet is the controlling reference for pin functions, compensation, electrical limits, and test conditions. This page combines the LM201ADT operating limits, package information, direct replacement considerations, comparison parameters, and practical design guidance to support faster component selection and PCB implementation.

RFQ پەیوەندی
LM201AH - 1 MHz General-Purpose Op Amp | Texas Instruments
LM201AH

LM201AH - 1 MHz General-Purpose Op Amp | Texas Instruments

Texas Instruments LM201AH is a single-channel, general-purpose operational amplifier with 1 MHz gain-bandwidth product, 80 dB common-mode rejection ratio, 2 mV input offset voltage, and approximately 1.8 mA supply current, housed in an 8-pin TO-99 hermetic metal-can package. It is intended for instrumentation, analog measurement, filtering, buffering, current sensing, and precision-control circuits operating from -40 °C to +85 °C. An operational amplifier, or op amp, is a high-gain differential-input amplifier whose feedback network determines its closed-loop behavior. The LM201AH belongs to the general-purpose operational-amplifier class within the broader amplifier IC and signal-conditioning hierarchy. Its TO-99-8 construction provides a through-hole package option for laboratory, industrial, and legacy instrumentation designs where surface-mount compatibility is not required. The principal performance features include a 1 MHz gain-bandwidth product, 80 dB CMRR, 2 mV input offset voltage, and approximately 1.8 mA operating current. The wide common-mode rejection specification helps reduce unwanted behavior when the amplifier handles small signals superimposed on larger voltage references or sensor outputs. The hermetic TO-99-8 package supports applications requiring a conventional metal-can outline and eight through-hole connections. The LM201A family uses advanced processing to reduce input bias current and temperature drift while retaining the general-purpose characteristics of the earlier LM101A architecture. The device can operate with conventional dual power supplies, making it suitable for signal paths centered around ground. Engineers should nevertheless verify supply-voltage limits, input common-mode range, output swing, compensation requirements, and electrical limits against the manufacturer datasheet before finalizing a design. Typical uses include laboratory instrumentation, analog measurement front ends, active filters, transducers, current-sensing amplifiers, and precision feedback loops. In a filter or amplifier, its 1 MHz gain-bandwidth product limits usable closed-loop bandwidth according to the selected noise-gain configuration. For sensor interfaces, the 80 dB CMRR can help reject common-mode interference, while the 2 mV offset remains an important error term in precision measurements. When designing around the LM201AH, begin by checking the required output swing and input common-mode range at the actual supply voltage. Decoupling should be placed close to the power pins, and the circuit should avoid driving capacitive loads unless stability behavior has been evaluated. Because the exact pin names and electrical limits are not included in the supplied search excerpts, those details should be confirmed in the Texas Instruments LM201A-N documentation before PCB release. This page consolidates the supplied distributor and manufacturer listings with practical selection guidance, package-aware alternatives, comparison parameters, and design cautions. It distinguishes confirmed data from unavailable fields so engineers can verify critical specifications without relying on assumptions.

RFQ پەیوەندی
LM201AN - Single Non-Compensated Op Amp | STMicroelectronics
LM201AN

LM201AN - Single Non-Compensated Op Amp | STMicroelectronics

The STMicroelectronics LM201AN is a single, general-purpose, non-compensated bipolar operational amplifier supplied in an 8-pin PDIP package. The confirmed headline characteristics are one amplifier circuit per package, a maximum input offset current of 20 nA over the operating temperature range, and the ability to obtain a slew rate of 10 V/µs when compensated appropriately for the intended circuit. An operational amplifier is a high-gain, differential-input analog building block used to amplify voltage differences, buffer signals, and perform linear operations such as summation, integration, and filtering. The LM201 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog IC, and semiconductor. Unlike a unity-gain-stable amplifier with internal compensation, the LM201AN is externally compensatable, allowing the circuit designer to select a compensation capacitor suited to the gain, bandwidth, and stability requirements of a particular application. Key features include a low input offset current, a maximum of 20 nA over temperature, and user-selectable compensation. These characteristics are especially relevant to precision analog circuits in which bias-current loading, input balance, and closed-loop stability can materially affect signal integrity. The device is offered as a single amplifier rather than a multi-amplifier package, simplifying board partitioning when separate analog channels require independent compensation or grounding. The non-compensated architecture gives designers control over stability-bandwidth tradeoffs. A compensation capacitor can be omitted or changed for unity-gain service, while larger values or added frequency compensation can improve stability in noise-gain configurations. With proper compensation, the manufacturer-reported capability includes a slew rate of up to 10 V/µs. This makes the LM201AN potentially useful where signal speed matters more than the compactness of a fixed-compensation amplifier. Typical applications include precision instrumentation amplifiers, logarithmic and summing amplifiers, active filters, transducers with relatively high source impedance, laboratory measurement systems, and low-frequency analog signal-conditioning chains. Its external compensation also permits optimization for different closed-loop gains rather than imposing one fixed stability profile across every application. When designing around the LM201AN, select the compensation network for the actual noise gain and verify closed-loop phase margin on the assembled board. Keep input and output return paths short, observe the device's specified supply and common-mode limits, and prototype compensation before high-volume production. External compensation makes the part flexible, but it also places a stability responsibility on the engineer. This page combines confirmed manufacturer-distributor data with clearly marked gaps, practical compensation guidance, package-aware replacement analysis, and procurement information. It distinguishes verified LM201AN characteristics from unverified specifications so engineers can make faster component-selection decisions without mistaking generic amplifier assumptions for device-specific facts.

RFQ پەیوەندی