بەرهەمەکان (3,200+)

LM2904YPT - Dual 1.1MHz Op Amp | STMicroelectronics
LM2904YPT

LM2904YPT - Dual 1.1MHz Op Amp | STMicroelectronics

STMicroelectronics LM2904YPT is a low-power dual operational amplifier in an 8-TSSOP package, providing two independent general-purpose amplifier channels with single-ended outputs. The device is specified for 100 dB of open-loop voltage gain and 1.1 MHz of gain-bandwidth product, making it appropriate for signal-conditioning stages that require stable operation from low-frequency instrumentation through audio-range circuits. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 belongs to the dual operational amplifier family, combining two amplifier channels in one package. Within the broader hierarchy, it is a low-power bipolar operational amplifier, a general-purpose amplifier IC, and a component within the wider analog signal-processing and semiconductor product category. The LM2904YPT's two channels can be configured independently as inverting amplifiers, non-inverting amplifiers, comparators, buffers, or differential amplifier stages. Its 100 dB open-loop gain supports accurate signal amplification when closed-loop feedback controls the operating gain. The 1.1 MHz gain-bandwidth product establishes the bandwidth available for closed-loop operation, while the low-power characterization supports economical designs where amplifier power consumption is an important system constraint. This dual architecture reduces component count and PCB area when a board requires two amplifier functions. It is particularly useful in sensor interfaces, analog signal conditioning, active filters, low-level audio paths, and general industrial control circuits. Because both channels share one package, designers should also evaluate common thermal and supply conditions rather than treating the two amplifier sections as completely independent systems. Typical circuit implementation uses conventional negative feedback, input bias-current compensation where required, and suitable decoupling near the supply pins. Input and output signal levels must remain compatible with the device's operating limits, while stable feedback and suitable output loading are necessary to maintain expected performance. Signal-routing practices should minimize coupling between the high-gain inputs and nearby switching or digital nodes. This page combines the exact LM2904YPT configuration, verified distributor listings, drop-in replacement analysis, package-level pin information, and practical design guidance. It helps engineers narrow the selection before requesting a quote for the dual low-power operational amplifier in its compact 8-TSSOP package.

RFQ پەیوەندی
LM2904YST - Dual Low-Power Op Amp, 8-MiniSO | STMicroelectronics
LM2904YST

LM2904YST - Dual Low-Power Op Amp, 8-MiniSO | STMicroelectronics

The STMicroelectronics LM2904YST is a dual, low-power bipolar operational amplifier designed for general-purpose signal conditioning. The device provides two independent amplifier channels in an 8-pin MiniSO package and is specified for supply voltages up to 30 V, including operation from ±15 V rails. Its low-power design, broad input-voltage capability, and single-ended outputs make it suitable for industrial control, sensor interfaces, audio stages, and general analog signal-processing circuits. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 contains two such amplifier sections, allowing one package to process two related signals or to implement two stages of a larger circuit. As a bipolar operational amplifier, it provides input bias-current behavior and voltage-noise characteristics suited to many low-cost precision and control applications rather than the very low input bias current associated with CMOS or JFET input devices. The LM2904YST supports operation across a wide supply range and can operate with dual supplies such as ±15 V. The 30 V maximum supply rating provides useful headroom for industrial applications, while the low-power operating-current target reduces heat generation in battery- and line-powered equipment. Each channel uses a differential input arrangement and provides a single-ended output referenced to the negative supply rail. Common applications include buffering sensors, amplifying low-level control signals, and driving external circuitry within the amplifier’s output-current capability. The 8-MiniSO package is a compact surface-mount form factor that reduces board space compared with traditional through-hole SOIC packages. The YST ordering suffix identifies the tape-and-reel presentation, allowing the amplifier to be assembled through standard surface-mount production processes. Because operational-amplifier performance depends on surrounding passives and layout, input and feedback components should be positioned close to the relevant pins, while adequate supply bypassing should be placed directly across the device’s supply terminals. LM2904YST is appropriate for industrial instrumentation, feedback-control loops, transducer amplification, audio preamplification, and low-frequency analog filters. The dual-channel arrangement can reduce component count in designs using two separate gain stages. In designs requiring input offset current below the LM2904’s range, rail-to-rail precision, or operation from a single low-voltage supply, a CMOS-input amplifier may offer a better technical match even if it shares a similar package. Designers should verify input and output voltage limits at the selected supply voltage, confirm the required gain bandwidth and slew rate, and check that the planned load does not exceed the output-current capability. Input common-mode range, output swing, electrical-noise limits, and thermal performance should be checked against the worst-case operating conditions. Decoupling capacitors should be selected according to the manufacturer’s recommended application circuit and stability requirements. This product overview combines the manufacturer-distinguished LM2904YST configuration with package, application, cross-reference, and design-placement guidance. It supports faster component identification while emphasizing the distinctions engineers must validate before approving any analog signal-chain design.

RFQ پەیوەندی
LM2924M Low-Power Op Amp/Comparator | Texas Instruments
LM2924M

LM2924M Low-Power Op Amp/Comparator | Texas Instruments

Texas Instruments LM2924M is a low-power dual-purpose analog IC containing two independent building blocks: a high-gain, internally frequency-compensated operational amplifier and a precision voltage comparator. The device is packaged in an 8-pin SOIC and is identified as an industrial-temperature-grade component. This combination allows one package to provide signal amplification and threshold detection without using separate amplifier and comparator packages. An operational amplifier is a voltage amplifier whose closed-loop gain is established by an external feedback network. A voltage comparator compares two input voltages and switches its output according to their relationship. The LM2924M combines these complementary functions in a single analog device, placing it in the operational-amplifier and comparator hierarchy while supporting transducer, sensing, control, and signal-conditioning applications. The internally frequency-compensated operational amplifier is designed to operate without an external compensation capacitor, simplifying implementation in basic gain configurations. Its comparator section provides an independent decision-making channel, allowing the two internal circuits to monitor or condition separate signals simultaneously. Because the amplifier and comparator are independent building blocks, their inputs and outputs can be used for different stages of a system. The National Semiconductor datasheet describes the LM2924M as a low-power operational amplifier and voltage comparator for precision voltage-amplification and related analog signal-processing needs. The 8-pin SOIC package provides a compact surface-mount format for industrial equipment, embedded controls, instrumentation interfaces, and mixed analog-digital circuit boards. Typical applications include transducers whose weak outputs require voltage amplification, sensor interfaces requiring a defined switching threshold, industrial control loops, and analog monitoring subsystems. The dual internal architecture can reduce board area when a design needs both continuous analog amplification and discrete threshold detection. For PCB implementation, assign the supply, ground, input, and output pins according to the manufacturer pin-description table and preserve the recommended input/output operating conditions. Confirm signal ranges, output states, stability requirements, and temperature limits against the device datasheet before connecting external transducers or logic interfaces. This page combines the device architecture, package details, sourcing guidance, verified replacement constraints, and practical application guidance. It also distinguishes confirmed drop-in choices from merely similar amplifier or comparator products, helping engineers avoid replacements that require PCB changes or behavioral redesign.

RFQ پەیوەندی
LM2924MX - Low-Power Amplifier/Comparator | Texas Instruments
LM2924MX

LM2924MX - Low-Power Amplifier/Comparator | Texas Instruments

Texas Instruments LM2924MX is a low-power bipolar analog IC that combines an operational-amplifier function with voltage-comparator operation in an 8-pin SOIC package. It is identified as a single-function transducer-amplifier circuit, is designed for industrial-temperature use, and is supplied in a rectangular surface-mount SOP package. The LM2924MX therefore serves as a compact analog signal-conditioning component for systems that require amplification and threshold detection in one package. An operational amplifier is a voltage-controlled analog amplifier whose open-loop gain is made large enough to amplify small signals accurately when negative feedback is applied. A voltage comparator compares one input voltage with another and changes its output state when a threshold is crossed. Together, these functions form part of the broader linear and mixed-signal IC hierarchy, where they support sensor conditioning, control loops, signal detection, and industrial interface circuits. The LM2924MX combines three notable product attributes. First, its bipolar construction places it in the classical family of analog amplifier ICs. Second, its single-function analog-circuit architecture supports compact implementation of transducer and signal-conditioning paths. Third, the 8-pin surface-mount SOIC package permits automated assembly while reducing board area compared with larger through-hole packages. Its industrial temperature grade also positions it for equipment operating beyond typical commercial-temperature conditions. LM2924MX is identified as a low-power operational amplifier and voltage comparator. This dual operating role allows the same device to amplify a low-level analog signal and evaluate whether that signal has crossed a defined reference level. In feedback-based configurations, the amplifier behavior supports closed-loop gain; in open-loop threshold service, the comparator behavior provides a digital indication of an analog condition. Exact gain-bandwidth, input-offset, supply-voltage, and output-current limits should be confirmed from the manufacturer datasheet before final circuit sizing. Typical uses include bridge or resistive-transducer signal conditioning, industrial sensor interfaces, low-level control-signal amplification, threshold detection, and alarm-generation circuits. The 8-pin SOIC footprint is suitable for compact analog boards where a surface-mount part is preferred and where signal conditioning must be placed close to the sensor or source to minimize susceptibility to interference. Designers should determine the allowable supply range, input common-mode range, output swing, input-offset voltage, noise, and comparator propagation behavior from the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, while sensitive input routing should avoid switching nodes and high-current return paths. Feedback resistors and any hysteresis network must be evaluated for the required gain, offset, and threshold stability. This product page consolidates the exact package, temperature-grade, circuit-type, and lifecycle information for LM2924MX, maps suitable analog applications, and provides engineering guidance for layout, compensation, and sourcing. It also distinguishes confirmed drop-in replacements from merely similar amplifier or comparator families so that PCB reuse decisions remain technically defensible.

RFQ پەیوەندی
LM293AD - Dual Differential Comparator, 2-36V | Texas Instruments
LM293AD

LM293AD - Dual Differential Comparator, 2-36V | Texas Instruments

Texas Instruments LM293AD is an industrial-grade dual differential comparator with two independent comparison channels, a 2 V to 36 V supply range, rail-to-rail input operation, and open-collector/open-drain outputs. The device is packaged in an 8-pin SOIC and is designed for sensing and control applications involving wide input and output voltage conditions. A differential comparator is an integrated circuit that compares two input voltages and changes its output state according to their relationship. Its two channels can monitor thresholds, detect crossings, implement window functions, or generate control signals. The LM293 belongs to the comparator hierarchy within analog interface ICs, where it bridges analog sensing and digital control logic. The LM293AD operates from 2 V to 36 V and provides a response time of approximately 300 ns. Its common-mode input range includes ground, and its differential input range can equal the maximum-rated supply voltage of ±38 V according to the manufacturer product information. Open-collector outputs support wired logic, pull-up arrangements, level translation, and compatibility with TTL, MOS, and CMOS systems. Each comparator section compares an inverting input with a non-inverting input. When the non-inverting input is higher, the corresponding open-collector output transistor turns off; when the inverting input is higher, the output transistor turns on. An external pull-up resistor is required for conventional open-collector operation. The two channels share the supply pins but retain separate input and output pins. Typical uses include industrial sensor interfaces, battery monitoring, power-supply fault detection, overvoltage protection, relay or LED indication, and control systems that compare an analog voltage against a reference. The wide operating supply range is useful when the comparator must tolerate industrial transients while operating from a higher-voltage rail. Designers should verify input and output absolute maximum ratings, provide adequate pull-up resistors, maintain a valid common-mode range, and account for output-current limits when several wired-open-collector outputs share a bus. Because the outputs can sink current but cannot source it independently, external pull-ups determine the high logic voltage and rise-time behavior. This product page combines manufacturer specifications, verified distributor listings, same-package replacement guidance, and practical comparator-design notes. It helps engineers evaluate the LM293AD for industrial threshold detection, protection, monitoring, and open-collector interface designs without confusing it with open-drain parts that use different output structures.

RFQ پەیوەندی
LM293AM - Dual Differential Comparator, 36 V, SOIC-8 | onsemi
LM293AM

LM293AM - Dual Differential Comparator, 36 V, SOIC-8 | onsemi

The onsemi LM293AM is a dual differential comparator designed for single-supply operation up to 36 V or dual-supply operation up to ±18 V, and it is available in an 8-pin SOIC package. Its differential inputs allow two voltages to be compared, while the open-collector output structure supports flexible interface and pull-up arrangements in control, sensing, and protection circuits. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The dual configuration provides two independent comparators in one package. When used with an external pull-up, an open-collector output can drive TTL, MOS, or CMOS-compatible circuitry while also allowing wired logic, level translation, or system reset behavior. The LM293AM belongs to the comparator hierarchy within amplifier and interface ICs. Key features include single-supply operation to 36 V, dual-supply operation to ±18 V, a typical low-current drain of 800 µA, and a typical input bias current of 25 nA. The device can compare input voltages near ground potential and is compatible with multiple logic families. Its low input bias current helps reduce source-loading effects in high-impedance sensing networks, while the wide supply range supports industrial and automotive-style control environments. The LM293AM uses open-collector outputs rather than push-pull outputs. This architecture provides a useful advantage when a comparator output must remain inactive until an external pull-up supplies the required logic-high voltage. It also supports open-wired signal arrangements, but every application must include the appropriate pull-up resistor and verify that the resulting rise time is acceptable. The operating common-mode range, differential input limits, output sink capability, and timing behavior should be checked against the manufacturer datasheet for the selected manufacturer version. Typical applications include industrial control systems, power-supply supervision, motor and solenoid protection, battery monitoring, sensor-threshold conditioning, window or level detection, and general-purpose logic interfaces. The dual comparator arrangement is particularly useful when one circuit monitors two related thresholds or when an enable function and a fault signal can be implemented with the two channels in a compact footprint. For PCB design, place the device so that sensitive input traces remain away from switching nodes and output pull-up routing. Keep input and output paths separate to reduce feedback through supply or board-level coupling. Confirm the logic-high level, output rise time, input common-mode range, supply decoupling requirements, and operating temperature range before releasing the design for production. This page combines manufacturer-family operating limits, package details, sourcing guidance, replacement analysis, and practical PCB considerations to support faster component selection. Review the complete pin assignment and electrical characteristics in the LM293AM datasheet before layout, particularly when the same circuit must accommodate multiple LM293-family variants.

RFQ پەیوەندی
LM293AN - Dual Open-Collector Comparator | STMicroelectronics
LM293AN

LM293AN - Dual Open-Collector Comparator | STMicroelectronics

The STMicroelectronics LM293AN is a low-power dual voltage comparator with two independent comparator channels, open-collector and open-drain outputs, and an 8-DIP package. The device is designed for general-purpose signal comparison and can operate from a single supply over a wide voltage range, while split-supply operation is also possible. Its listed rail-to-rail input designation, ground-referenced common-mode capability, and TTL, MOS, and CMOS output compatibility make it suitable for threshold detection, level translation, and analog-control systems. A voltage comparator is an integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. In this role, LM293AN belongs to the comparator IC hierarchy within analog and mixed-signal semiconductors. Each of its two channels can evaluate a non-inverting input against an inverting input, allowing one package to perform two related comparisons while keeping channel operation independent. The LM293 family documentation identifies low power consumption as a defining characteristic and specifies input-offset voltage as low as 2.0 mV maximum for the associated two-comparator family. Open-collector outputs provide flexibility when the destination device requires a pull-up resistor, particularly in wired logic, relay-driver, and legacy digital-interface applications. The outputs are also listed as compatible with TTL, MOS, and CMOS logic families. Operation from a single supply is central to the device design. The common-mode input range includes ground, while the differential input voltage can extend to the maximum-rated supply voltage of ±38 V according to TI's LM293 family information. The 8-DIP mechanical format provides through-hole access to the two comparator channels, power, ground, and output connections. Typical uses include industrial control thresholds, sensor-interface decisions, window comparators, oscillator and timer designs, and general logic level conditioning. The two independent channels can also implement a larger comparator arrangement through external resistor networks. Open-collector outputs make pull-up selection an important part of the interface design because the output cannot directly drive a logic high without this external support. The main design consideration is that open-collector outputs require correctly selected pull-up resistors and adequate logic-level rise time at the driven node. Supply decoupling, input-source impedance, output load, and common-mode headroom should be reviewed against the application's operating conditions. This page consolidates the verified device identity, package information, sourcing links, and practical comparator-selection guidance.

RFQ پەیوەندی
LM293D - Dual Differential Comparator, 8-SOIC | TI
LM293D

LM293D - Dual Differential Comparator, 8-SOIC | TI

The Texas Instruments LM293D is a dual differential comparator designed for low-voltage operation from a single supply or split supplies. The verified distributor listing identifies it as a standard general-purpose comparator with open-collector, open-drain, rail-to-rail operation in an 8-SOIC package. The device contains two independent comparator channels, making it suitable for threshold detection, level shifting, window monitoring, and basic analog control systems. According to the Texas Instruments LM293 product page, the device is a dual differential comparator in an industrial-grade family; detailed electrical limits are not supplied in the verified excerpts and therefore remain marked for data completion. A comparator is an analog signal-conditioning IC that compares two input voltages and produces a logic-level output indicating which input is higher. A differential comparator belongs to the broader comparator, amplifier, and analog interface hierarchy, while the LM293D is specifically a low-power, dual-channel comparator for embedded and control applications. Its two independent channels allow simultaneous comparison of two signal pairs, provided the device operates within the manufacturer-rated common-mode and supply limits. The verified TI page states that the LM293 family supports wide supply-voltage operation, including systems using split power supplies. TI also states that the B-version is a drop-in replacement for LM293, LM393, and LM2903; however, the provided data does not establish that every related suffix is electrically identical for every use condition. The LM293D listing identifies open-collector/open-drain and rail-to-Rail output characteristics, which are important when interfacing with pull-up-based digital systems. Typical uses include monitoring a battery or power rail, detecting sensor thresholds, comparing external reference voltages, and implementing basic overvoltage or undervoltage indication. The open-drain output requires an external pull-up resistor when the output must rise to a defined logic level. Because the verified data does not provide exact input-offset, response-time, supply-current, or temperature values, those specifications are retained as data-needed markers rather than inferred from related devices. For PCB design, place the IC close to the compared signals and use short, low-noise routing for high-impedance input nodes. Keep pull-up resistors close to open-drain outputs, and account for input common-mode range and supply polarity in both single-supply and split-supply systems. The LM293D is not a power semiconductor, so SOA data is not applicable.

RFQ پەیوەندی
LM293DG - Dual Precision Comparator, 2-36V, SOIC-8 | onsemi
LM293DG

LM293DG - Dual Precision Comparator, 2-36V, SOIC-8 | onsemi

The onsemi LM293DG is a dual independent precision voltage comparator in an 8-pin SOIC package, built for single or split supply operation across a 2 V to 36 V supply range. Each channel offers an input offset voltage as low as 2.0 mV, a 1.3 microsecond response time, and a supply current of about 400 microamps per channel, with an open-collector (open-drain) output stage compatible with TTL, MOS and CMOS logic. A comparator is a differential amplifier used as a simple decision element: it compares two input voltages and switches its output state when the non-inverting input rises above the inverting input. The comparator category sits above discrete transistor switches in the signal-conditioning hierarchy and below instrumentation amplifiers in the analog IC family, sitting in the amplifier IC / signal conditioning control group of parts such as op amps, references and sensor interface ICs. The LM293 series is distinguished from general-purpose comparators by its low input offset voltage, wide supply range and ability to operate with the common-mode input range extending to ground, which makes it a strong fit for single 5 V or single 12 V systems where the signal of interest lives near the negative rail. The two channels are fully independent, each with its own pair of inputs and output. The open-collector output stage is the key architectural feature: the output transistor sinks current but never sources it, so an external pull-up resistor to the supply or logic rail is required to establish a valid high level. That architecture permits level shifting to any voltage up to the maximum supply, wired-AND bus tying, and direct drive of relay or solenoid drivers without a buffer stage. Because the output stage is a bipolar NPN transistor, output sink current is limited compared with modern CMOS comparators. Typical applications include overvoltage and undervoltage protection in linear and switching power supplies, battery and pack monitoring window comparators, motor stall and over-current detection, industrial sensor thresholding, and automotive-style sensor protection. The SOIC-8 package with 1.27 mm lead pitch supports both through-hole assembly and standard surface mount reflow, and the -25 C to +85 C ambient range covers industrial and consumer equipment. When designing with the LM293DG, always fit a pull-up resistor on each output and check the sink current against the pull-up value and the load. If your design needs rail-to-rail input operation, push-pull outputs, or a supply below 2 V, a CMOS comparator is the better choice; if it needs low offset with wide supply and open-drain flexibility, the LM293DG remains a proven, low-cost choice. This page consolidates manufacturer specifications, drop-in replacement candidates, pin-level detail and practical design guidance so that you can qualify the LM293DG for an existing board revision without redrawing the footprint.

RFQ پەیوەندی
LM293DMR2 - Dual Precision Comparator, 36 V | onsemi
LM293DMR2

LM293DMR2 - Dual Precision Comparator, 36 V | onsemi

The onsemi LM293DMR2 is a dual low-offset voltage comparator with two independent comparison channels, a 2 V to 36 V supply range, open-collector outputs, and an 8-pin TSSOP package. Each channel can operate from single or split power supplies, allowing common-mode input signals to approach ground during single-supply operation. The low input offset voltage, specified as low as 2.0 mV, supports accurate threshold detection in industrial, automotive, and consumer circuits. A voltage comparator is an analog signal-conditioning IC that compares two input voltages and produces a digital logic state at its output. The LM293 belongs to the comparator hierarchy, which includes differential comparators, window comparators, and precision comparators. By converting an analog threshold relationship into an open-collector logic indication, this type of device bridges analog measurement circuits and digital control, monitoring, or protection systems. The principal features include two independent comparators, low offset voltage, a common-mode input range extending to ground under single-supply operation, and open-collector outputs that can sink current from multiple compatible devices. The 2 V to 36 V operating supply range accommodates 5 V, 12 V, and 24 V systems. The onsemi datasheet also identifies the device as suitable for consumer, automotive, and industrial applications where reliable voltage-level detection is required. Each comparator channel is independent, allowing one device to perform two unrelated threshold measurements. The open-collector architecture requires an external pull-up resistor and provides a wired-output capability when several comparator outputs share a bus. This architecture does not actively drive the output high, but it offers flexible voltage-level adaptation and enables wired-AND behavior when output collectors are connected. Typical uses include monitoring a 12 V or 24 V automotive battery, detecting overvoltage and undervoltage conditions in industrial power systems, comparing sensor outputs with adjustable thresholds, and providing simple supervisory functions in consumer equipment. The grounded common-mode capability is especially useful in single-supply systems where the signal of interest begins near 0 V and cannot be compared reliably by a comparator with a restricted input range. For robust PCB implementation, place input resistors close to the comparator pins to limit differential pickup and route the inputs away from switching nodes and high-current paths. Select the external output pull-up for the intended logic voltage, and confirm that its maximum sink current remains within the device output ratings. Check that the common-mode and differential input voltages remain within the absolute maximum limits during power transients. This product page combines the manufacturer specifications, package and pin information, drop-in replacement analysis, comparison data, and practical PCB guidance to accelerate design review and sourcing. The technical recommendations focus on preserving the LM293DMR2 role as a reliable, low-offset dual comparator while making package, electrical, and supply constraints explicit before layout release.

RFQ پەیوەندی
LM293DR - Dual Differential Comparator, 8-SOIC | TI (Tape & Reel)
LM293DR

LM293DR - Dual Differential Comparator, 8-SOIC | TI (Tape & Reel)

The Texas Instruments LM293DR is a dual differential comparator designed for low-voltage operation from a single supply or split supplies. The verified distributor listing identifies it as a standard general-purpose comparator with open-collector, open-drain, rail-to-rail operation in an 8-SOIC package. The device contains two independent comparator channels, making it suitable for threshold detection, level shifting, window monitoring, and basic analog control systems. According to the Texas Instruments LM293 product page, the device is a dual differential comparator in an industrial-grade family; detailed electrical limits are not supplied in the verified excerpts and therefore remain marked for data completion. A comparator is an analog signal-conditioning IC that compares two input voltages and produces a logic-level output indicating which input is higher. A differential comparator belongs to the broader comparator, amplifier, and analog interface hierarchy, while the LM293DR is specifically a low-power, dual-channel comparator for embedded and control applications. Its two independent channels allow simultaneous comparison of two signal pairs, provided the device operates within the manufacturer-rated common-mode and supply limits. The verified TI page states that the LM293 family supports wide supply-voltage operation, including systems using split power supplies. TI also states that the B-version is a drop-in replacement for LM293, LM393, and LM2903; however, the provided data does not establish that every related suffix is electrically identical for every use condition. The LM293DR listing identifies open-collector/open-drain and rail-to-Rail output characteristics, which are important when interfacing with pull-up-based digital systems. Typical uses include monitoring a battery or power rail, detecting sensor thresholds, comparing external reference voltages, and implementing basic overvoltage or undervoltage indication. The open-drain output requires an external pull-up resistor when the output must rise to a defined logic level. Because the verified data does not provide exact input-offset, response-time, supply-current, or temperature values, those specifications are retained as data-needed markers rather than inferred from related devices. For PCB design, place the IC close to the compared signals and use short, low-noise routing for high-impedance input nodes. Keep pull-up resistors close to open-drain outputs, and account for input common-mode range and supply polarity in both single-supply and split-supply systems. The LM293DR is not a power semiconductor, so SOA data is not applicable.

RFQ پەیوەندی
LM293DR2G - Dual 36V Comparator | onsemi | Signal Control
LM293DR2G

LM293DR2G - Dual 36V Comparator | onsemi | Signal Control

The onsemi LM293DR2G is a dual precision voltage comparator rated for 2 V to 36 V operation, with a 1.3 µs response time and open-collector, open-drain outputs in an 8-pin SOIC package. The device contains two independent comparator channels and can operate from a single supply or split supplies, making it suitable for industrial threshold detection, sensing, and control circuits. A voltage comparator is an analog signal-conditioning device that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. Within the broader hierarchy of semiconductor components, the LM293DR2G belongs to the comparator category, analog signal-conditioning ICs, and power-management-adjacent control devices. Its two independent channels allow one package to perform two comparisons while sharing a common supply and ground. The principal operating characteristics include a 2 V to 36 V supply range, a 1.3 µs response time, and a dual open-collector output architecture. The output structure can sink useful load current and requires an appropriate pull-up arrangement when driving subsequent digital stages. According to the onsemi LM293 family information, input offset voltage can be as low as 2.0 mV, while the LM293 series is designed for common-mode input operation down to ground with single-supply operation. Each internal channel has differential inputs and an independently controlled output. Separate inputs allow the circuit designer to define the polarity of each decision, while separate output stages provide isolation between the two comparator functions. The 8-pin SOIC package supports conventional surface-mount assembly, but exposed-pad thermal management is not part of this package. Exact offset-voltage limits, input bias current, output-current limits, and channel-matching figures should be selected from the ordering information for the exact grade. Typical uses include industrial sensor thresholds, motor and actuator control, power-supply monitoring, window or level detection, and general signal conditioning. In these systems, the comparator converts an analog relationship between two voltages into a logic-compatible indication that downstream control logic can process. The 36 V maximum supply capability is especially useful when the sensing circuit operates from an industrial bus rather than a low-voltage logic rail. For dependable operation, treat each open-drain output as requiring a pull-up to the supply used by the receiving logic. Keep input and feedback traces short, provide a local supply bypass capacitor, and confirm that input voltages remain within the applicable common-mode and absolute-maximum limits. Account for output rise time after the pull-up resistor is added because the stated 1.3 µs response describes comparator propagation behavior, not the complete RC-controlled transition at the output node. This product record combines the manufacturer family description with package, supply, temperature, and response-time details, then adds application guidance, pin-level implementation notes, and same-footprint comparison choices. These engineering views help designers evaluate the LM293DR2G as a dual comparator rather than treating it only as an eight-pin logic IC.

RFQ پەیوەندی
LM293DRE4 Dual Differential Comparator 36V | Texas Instruments
LM293DRE4

LM293DRE4 Dual Differential Comparator 36V | Texas Instruments

The Texas Instruments LM293DRE4 is a dual differential comparator IC designed for single-supply or split-supply operation, with a maximum tested supply voltage of 36 V and an 8-SOIC package. The device contains two independent comparators with open-collector, open-drain outputs, allowing the output state to be pulled up externally. Its wide supply-voltage range, low supply-current drain of approximately 0.4 mA per comparator, and input common-mode range that includes ground make it suitable for industrial voltage-threshold, sensing, and control applications. A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM293 belongs to the comparator category within analog signal-chain and power-management ICs, rather than acting as an amplifier or regulator. Two comparators in one package provide independent channels for monitoring two thresholds, controlling two loads, or implementing a window-detection function. The open-collector outputs are useful for wired logic, relay-driver interfaces, and systems requiring a pull-up resistor. The main electrical characteristics include operation from a single supply or dual supplies, a 2 V to 36 V difference between supply rails, a common-mode input voltage range that includes ground, and low output saturation voltage. The LM293 is specified as compatible with TTL, MOS, and CMOS logic levels. The output structure can sink current from an external pull-up while providing a predictable low-level output, allowing designers to select the pull-up voltage independently of the comparator supply. The LM293 architecture is based on two independent comparator channels rather than a shared output. This arrangement allows each channel to use separate non-inverting and inverting inputs while sharing the device supply pins. The inputs are intended for low-power threshold sensing, and the operating range supports both traditional positive-supply circuits and circuits using ground as the lower input reference. Open-collector outputs require an external pull-up when a valid high output is required. Typical applications include industrial process-limit detection, battery and power-supply monitoring, sensor signal conditioning, overvoltage and undervoltage protection, relay or solenoid control interfaces, and window comparators. The comparator can also be used as a simple line-driver or discrete-amplifier element in low-frequency control circuits. Because the output is open collector, the pull-up resistor and load current must be selected to match the desired logic voltage and switching speed. For PCB design, place the decoupling capacitor close to the supply and ground pins, and route comparator inputs away from switching nodes and high-current paths. The 8-SOIC footprint allows straightforward through-hole assembly and rework. The pull-up resistor should connect from each output to the logic rail used by the receiving device. Confirm the input voltages, supply current, output sink current, and common-mode limits against the application before releasing the design. This product page combines the manufacturer’s LM293 family information, exact-MPN sourcing details, pin-level integration guidance, and drop-in replacement analysis. It is intended to help engineers move from component identification to schematic review, footprint verification, and robust analog threshold-circuit design.

RFQ پەیوەندی
LM293DRG3 - Dual Differential Comparator | Texas Instruments
LM293DRG3

LM293DRG3 - Dual Differential Comparator | Texas Instruments

The Texas Instruments LM293DRG3 is a dual differential voltage comparator in an 8-pin SOIC package. The device contains two independent comparison channels, supports ±15 V single-ended or 30 V total supply operation, and provides open-collector, open-drain outputs compatible with TTL, MOS, and CMOS logic. Its common-mode input range includes ground, allowing operation from a single positive supply, while the differential input range can extend to ±38 V. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a defined threshold. The LM293 belongs to the comparator hierarchy, which also includes differential comparators and open-collector interface comparators. These devices bridge low-level analog sensing and digital control by converting an analog condition into a logic-readable result. The LM293DRG3 offers two independent comparators, rail-to-rail output behavior, and low output saturation voltage. Its open-collector outputs permit wired-AND connections and external pull-up selection, making the device adaptable to different logic families and voltage domains. The common-mode input range including ground is particularly useful in battery-powered and industrial systems powered from a single rail. Each channel compares a non-inverting input with an inverting input and uses open-drain output transistors to indicate the polarity of the differential voltage. The outputs can sink current while remaining in a high-impedance state when inactive. Because the output stage does not actively drive a high voltage, pull-up resistors are required when a logic-high level is needed. Differential input protection and common-mode limits must be respected during fault conditions. Typical uses include monitoring a sensor output, detecting supply thresholds, comparing an analog measurement with a reference, generating window-limit signals, and supporting industrial control logic. Two independent channels allow related threshold functions to be implemented in one package, reducing component count while preserving separate input and output isolation. Designers should select pull-up resistors to suit the destination logic voltage and sink-current budget, connect an unused comparator input to a defined valid potential, and verify input and output behavior across the full supply range. This page combines ordering information, package details, drop-in replacement guidance, comparison data, and practical design guidance for faster component selection.

RFQ پەیوەندی
LM293DRG4 - Dual Open-Collector Comparator | Texas Instruments
LM293DRG4

LM293DRG4 - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM293DRG4 is a dual differential comparator with two independent channels, open-collector outputs, and an 8-pin SOIC package. It supports single-supply operation over a wide voltage range and dual-supply operation when the total supply difference is between 2 V and 36 V. Each channel compares an inverting input with a non-inverting input and provides a logic-compatible indication of the input relationship. A comparator is an analog integrated circuit that evaluates two voltages and changes its output state when one input crosses the other. Within the signal-chain hierarchy, the LM293 belongs to the comparator class, which sits alongside amplifiers and other analog interface ICs used to convert continuous voltage relationships into binary logic decisions. The LM293's open-collector outputs are useful when a system needs a pulled-up logic signal, wired logic, level translation, or an adjustable output rise time. The LM293 family is specified as a dual differential comparator for industrial applications. The LM293DRG4 ordering code identifies the 8-SOIC package and tape-and-reel shipping configuration. Its two channels are independent, allowing one device to implement two threshold decisions. Open-collector outputs also permit multiple devices to share a common pull-up bus when the system designer confirms that the resulting wired-AND behavior is intentional. The device can operate from a single supply or from positive and negative supplies. The manufacturer states that the common-mode input range includes ground, that the differential input range equals the maximum-rated supply voltage, and that the output is compatible with TTL, MOS, and CMOS logic. The LM293B version is identified as a drop-in replacement for LM293, LM393, and LM2903 families, providing a useful basis for qualified equivalent selection. Typical applications include power-supply threshold detection, sensor-signal conditioning, industrial control interfaces, battery monitoring, and digital logic level translation. In a sensor interface, the non-inverting input can receive a reference voltage while the inverting input receives the sensed signal, allowing the open-collector output to indicate when the signal crosses the selected threshold. The output requires an external pull-up because the LM293 does not actively drive its output high. Designers should account for input offset voltage, common-mode limits, supply voltage, output pull-up resistance, and propagation delay. Input components should also prevent excessive differential input voltage and protect sensitive sensor nodes from electrostatic discharge. Because the output is open collector, the pull-up resistor and its placement materially affect rise time, power consumption, and susceptibility to interference. This page combines the LM293 family architecture, verified ordering and package information, practical replacement criteria, threshold-comparison guidance, and PCB-focused design considerations. It also distinguishes genuine pin-compatible choices from options that require changes to output pull-ups, supply arrangements, or board layout.

RFQ پەیوەندی
LM293DT - Dual 36V Low-Power Comparator | STMicroelectronics
LM293DT

LM293DT - Dual 36V Low-Power Comparator | STMicroelectronics

STMicroelectronics LM293DT is a low-power dual voltage comparator containing two independent comparator channels in an 8-pin SOIC package. Each channel supports a single supply from 2 V to 36 V or dual-supply operation, while the input stage accepts input voltages spanning the supply rails. The device uses open-collector output stages suitable for driving wired-AND, open-drain, and pull-up-based interfaces. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM293 belongs to the comparator hierarchy, where a comparator is a signal-conditioning IC used between sensors, amplifiers, reference voltages, and digital control logic. Its two independent channels allow one package to perform two threshold decisions, reducing component count in industrial controls, monitoring equipment, and embedded systems. Key characteristics include very low supply current of 0.4 mA typical, 1 mW power consumption per comparator at a 5 V supply, low typical input bias current of 25 nA, and typical input offset current of ±5 nA. The typical input offset voltage is ±1 mV. Rail-to-rail input capability allows each comparator to operate with inputs near the negative and positive supply limits, while the open-collector outputs require an external pull-up resistor. The LM293DT uses a bipolar comparator architecture optimized for low power rather than high-speed operation. Its low input currents are useful when the source impedance is high or leakage would otherwise shift the comparison threshold. Because the outputs are open collector, two or more outputs can share a pull-up node to form a wired-AND function. The external pull-up determines output rise time, so resistance and capacitance must be selected together for the required switching speed. Typical applications include battery-powered threshold detection, sensor-signal conditioning, window comparators, overvoltage monitoring, industrial control interfaces, and simple switching regulators. The dual configuration is particularly useful when a system must monitor two independent limits or compare a measurement against both an upper and lower reference. For reliable PCB operation, place input and output bypass capacitors close to their associated pins and route comparator inputs away from switching nodes and high-current return paths. Account for input offset voltage and common-mode limits when defining detection thresholds. The open-collector outputs must always have a pull-up unless the output is intentionally left unconnected. This product page combines operating characteristics, application guidance, package information, and same-footprint replacement context to support faster component selection and board-level implementation.

RFQ پەیوەندی
LM293N - Dual Open-Collector Comparator, 8-DIP | STMicroelectronics
LM293N

LM293N - Dual Open-Collector Comparator, 8-DIP | STMicroelectronics

The STMicroelectronics LM293N is a dual, general-purpose voltage comparator with two independent channels, open-collector outputs, and an 8-DIP package. According to the STMicroelectronics LM293N product description, it is designed for single-supply operation across a wide voltage range, while operation from split power supplies is also possible. The verified distributor listing identifies the device as an 8-DIP comparator with open-collector/open-drain, rail-to-rail characteristics. Specific voltage, current, timing, temperature, and logic-threshold values were not included in the provided data and therefore require verification from the manufacturer datasheet before design release. A voltage comparator is an analog semiconductor that compares two input voltages and produces a logic-level indication of their relationship. The LM293N contains two independent comparators, allowing one package to implement threshold detection, window comparison, free-running oscillator, or simple analog-to-logic conversion. Within the broader hierarchy, it is a comparator IC, then an analog integrated circuit, and finally a semiconductor. Its open-collector outputs can sink external current and normally require a pull-up resistor when the design expects a high-level output. The primary documented feature is its ability to operate from a single supply over a wide range of voltages, with split-supply operation also supported. The two independent channels provide design flexibility for comparing a sensor against a reference, checking a power rail, or generating complementary decisions in control circuitry. The open-collector architecture can support wired logic and level translation, but the external pull-up, output current, propagation delay, and input common-mode limits must be checked against the actual datasheet. LM293N is suitable for industrial control, instrumentation, power-supply supervision, sensor interfaces, and embedded threshold detection. In a single-supply circuit, place the input network so that the signal remains within the device's verified common-mode range. In a split-supply circuit, confirm the positive and negative rail limits and the permitted total voltage. Because the provided data does not state absolute maximum ratings, supply voltage, input offset, output-current capability, response time, or operating temperature, those values should not be assumed. Design practice should include a local bypass capacitor, a defined pull-up resistor for each open-collector output, and protection for exposed sensor inputs. Avoid relying on an output high level until the pull-up network and downstream load have been analyzed. Verify input polarity, output inversion, hysteresis, and logic compatibility with the system controller. The 8-DIP package is mechanically important: use the manufacturer pinout and maintain adequate lead spacing during assembly. This page combines the verified LM293N product identity, package information, application context, datasheet links, and engineering considerations. It intentionally does not fabricate electrical ratings, pricing, lifecycle claims, or unreported pin names; obtain the current manufacturer datasheet and distributor quotation for production decisions.

RFQ پەیوەندی
LM293P - Dual 36V Differential Comparator | Texas Instruments
LM293P

LM293P - Dual 36V Differential Comparator | Texas Instruments

Texas Instruments LM293P is a dual differential comparator rated for a 2 V to 36 V supply range, with a stated propagation delay of 300 ns, packaged as an 8-pin PDIP. Each channel provides independent differential inputs and an open-collector output, making the device suitable for threshold detection, level translation, relay driving, and industrial control logic. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relative polarity. The LM293 belongs to the comparator hierarchy, which sits within linear and mixed-signal ICs. Its open-collector outputs can sink current from a pull-up network, allowing the outputs to be wired together when wired-OR operation is required. The principal features of the LM293P are its dual-channel architecture, differential input arrangement, wide 2 V to 36 V operating supply range, open-collector outputs, and 300 ns response time. The package is an 8-pin PDIP, providing a through-hole footprint suitable for prototypes, legacy industrial equipment, repair assemblies, and applications where leaded components are preferred. The LM293 contains two electrically independent comparator channels. Differential inputs are presented through inverting and non-inverting pins, while the output uses an open-collector transistor capable of pulling the output node toward ground. A pull-up resistor is required to establish a high output level, and the output stage can sink current from TTL, CMOS, and other logic families within the device's stated operating limits. Typical uses include monitoring a control or battery voltage against a reference, detecting sensor crossings, implementing overvoltage and undervoltage protection, driving relay or indicator circuits, and providing threshold-compatible interfaces between analog and digital systems. Because the device supports a wide supply range, it can also be used in industrial systems operating from conventional low-voltage DC rails. Designers must provide the required output pull-up and verify input common-mode limits, output-current limits, and operating temperature against the manufacturer datasheet. Input protection, bypassing, and leaded-component spacing should also be considered when the LM293P is used in high-noise or high-voltage surroundings. This page combines verified manufacturer and distributor information with package-level selection guidance, verified drop-in candidates, application use cases, and practical design notes. It is intended to help engineers identify whether the LM293P fits an existing 8-pin comparator design without confusing electrically related but mechanically different packages.

RFQ پەیوەندی
LM293QT - Dual Low-Power Wide-Supply Comparator | STMicroelectronics
LM293QT

LM293QT - Dual Low-Power Wide-Supply Comparator | STMicroelectronics

The STMicroelectronics LM293QT is a dual general-purpose comparator designed for low-power operation from a single supply or split supplies. The device provides two independent comparator channels, a wide single-supply operating range of 2 V to 36 V, and an open-collector output configuration. It is packaged in an 8-UFDFN package with a 2 mm x 2 mm body size. The LM293QT is suited to voltage-level detection, threshold comparison, industrial control logic, sensor interfaces, and low-current signal conditioning where a compact, low-power comparator is required. An analog comparator is an integrated circuit that evaluates two input voltages and changes its output state when the voltage at the non-inverting input becomes higher than the voltage at the inverting input. The LM293 family belongs to the comparator and linear IC hierarchy, where each independent channel compares its differential input while operating from a common supply. This makes the device useful between sensors and digital control systems, where a small voltage difference must be converted into a logic-compatible indication. The principal electrical characteristics include a 2 V to 36 V single-supply range, operation from split supplies of plus or minus 1 V to plus or minus 18 V, and very low supply current of approximately 0.45 mA. The comparator channels feature low input bias current of approximately 20 nA. The open-collector output stage allows the output to be pulled up to an external supply and enables wired-AND behavior when multiple comparator outputs are connected. The output type is suitable for interfacing with open-drain or open-collector digital devices. The LM293QT provides two independent channels in a compact 8-UFDFN package. The wide supply range allows operation from low-voltage systems through higher industrial rails, while the low supply current supports battery-operated and always-on equipment. The two channels can be used for independent threshold decisions, window monitoring, or complementary comparisons. Open-collector outputs require an external pull-up resistor when the output must rise to a defined logic-high voltage. Typical applications include industrial sensor interfaces, battery monitoring, power-supply sequencing, overvoltage and undervoltage detection, temperature-controller signal conditioning, and embedded threshold logic. Because the input common-mode range can include ground, the LM293QT is particularly useful in systems where the signal being monitored is close to the negative supply rail. When laying out a design, preserve the exposed-pad and package thermal requirements of the 8-UFDFN package. Route the comparator inputs away from switching nodes and high-current output paths, and place the input and output components close to their associated pins. Choose the external pull-up voltage and resistor to match the receiving logic, and verify that the output sink current remains within the device limits for the selected pull-up network.

RFQ پەیوەندی
LM293ST - Dual 2V-36V Comparator | STMicroelectronics
LM293ST

LM293ST - Dual 2V-36V Comparator | STMicroelectronics

The STMicroelectronics LM293ST is a dual differential voltage comparator designed for low-voltage operation, with a 2 V to 36 V supply range and open-collector, open-drain outputs. The device contains two independent comparator channels in an 8-pin MiniSO surface-mount package, allowing both channels to operate from the same supply or from split power rails. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM293 family belongs to the comparator and amplifier IC category within the broader semiconductor hierarchy. Its open-collector outputs can sink current while remaining in a high-impedance state, making the device suitable for wired logic, pull-up resistor networks, relay drivers, and systems that require a flexible output drive configuration. The LM293ST provides two independent comparators, low offset, and high precision according to the STMicroelectronics LM293 family information. Its rail-to-rail input operation allows each differential input to approach the supply rails, which is useful when monitoring low-voltage sensor signals or battery-powered thresholds. The open-collector outputs also provide a deliberate isolation between the comparator output and the supply voltage, permitting external pull-up selection for a different logic family. Both channels can operate from a single 2 V to 36 V supply, and the device also supports split power-supply arrangements. The low-power architecture is intended for general-purpose threshold detection rather than high-speed signal conditioning. Because the outputs are open collector, designers must add pull-up resistors when a continuously driven high level is required. The output transistor provides current sinking capability, while the external pull-up establishes the high-state voltage and limits the available rise rate. Typical applications include industrial sensor thresholding, overvoltage and undervoltage detection, battery monitoring, window-comparator circuits, control-loop signaling, and digital interface adaptation. Two channels can also implement a hysteretic switching controller, an automatic window detector, or a pair of independent limit alarms. In each case, input and output implementation details should be checked against the operating voltage, common-mode range, load current, and logic requirements of the completed circuit. The principal design consideration is that an open-collector output is not a push-pull logic output. Select the pull-up resistor and logic voltage carefully, keep the pull-up current within the output sink-current rating, and place the device close enough to the protected signal path to minimize pickup of switching noise. The exposed package also requires attention to copper area and thermal conditions when either channel operates continuously at maximum load. This product page brings together the manufacturer family information, distributor listing attributes, package details, replacement guidance, and practical design considerations. It also distinguishes verified electrical attributes from parameters that require confirmation from the LM293 manufacturer datasheet, helping engineers plan a replacement or design-in without relying on package-code assumptions.

RFQ پەیوەندی
LM321MF/NOPB - 1MHz, Single Op Amp, 3-32V, SOT-23-5 | TI
LM321MF/NOPB

LM321MF/NOPB - 1MHz, Single Op Amp, 3-32V, SOT-23-5 | TI

The Texas Instruments LM321MF/NOPB is a single-channel, low-power operational amplifier delivering 1 MHz unity-gain bandwidth and 0.4 V/us slew rate in a 5-pin SOT-23 (DBV) package. It operates from a single 3 V to 32 V supply (or dual +/-1.5 V to +/-16 V) and supports an input common-mode range that includes ground, enabling true single-supply operation. Housed in the industry-standard SOT-23-5 footprint, the LM321MF/NOPB combines economy with TI's LM321 bipolar architecture originally developed by National Semiconductor. An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output. Op amps belong to the amplifier IC family within integrated circuits, which also includes instrumentation amplifiers, comparators, and specialty audio/video amplifiers. The LM321MF/NOPB specifically is a general-purpose single op amp, meaning one amplifier channel per package; it sits in the hierarchy: op amp -> amplifier IC -> analog IC -> integrated circuit -> semiconductor. Key features include 1 MHz gain-bandwidth product, 0.4 V/us slew rate, low input offset voltage (typical 2 mV), input common-mode range that includes the negative rail, and large capacitive-load drive capability. The bipolar input stage with class-AB output provides robust performance across the wide 3 V to 32 V supply range. Internal ESD protection and thermal shutdown enhance field reliability. The LM321MF/NOPB uses a bipolar transistor input stage rather than CMOS or JFET, giving it inherently low noise voltage density but somewhat higher input bias current than modern CMOS alternatives. Its wide supply range allows direct connection to industrial 24 V rails, 12 V battery systems, or +/-15 V analog supplies, eliminating the need for additional level shifters. The 1 MHz bandwidth is sufficient for audio, sensor conditioning, and many active-filter topologies. Typical applications include transducer signal conditioning, low-frequency active filters, current sensing with high-side or low-side shunt, audio pre-amplifier stages, and general-purpose amplification in industrial controls. The SOT-23-5 footprint is ideal for space-constrained PCB designs such as handheld instruments and IoT sensor modules. When designing with the LM321MF/NOPB, verify input bias current (45 nA typical) is acceptable for high-impedance sensor interfaces. Place a 0.1 uF decoupling capacitor close to the VCC pin and ensure output capacitive loads stay within the datasheet's stability region to avoid oscillation. This page synthesizes distributor pricing, drop-in SOT-23-5 alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a faster path from datasheet to prototype.

RFQ پەیوەندی
LM324AD - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM324AD

LM324AD - Quad 30V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM324AD is a general-purpose quad operational amplifier containing four independent, internally frequency-compensated amplifiers. The device supports a 30 V maximum supply, operates at a gain-bandwidth product of 1.2 MHz, and has a 3 mV input offset voltage rating. It is supplied in a 14-pin SOIC package, enabling one component to provide four amplified channels in a compact surface-mount footprint. The LM324 family is designed for single-supply operation over a wide voltage range, while also supporting split-supply arrangements when the circuit requires a bipolar input or output range. An operational amplifier is an analog signal-processing IC that uses high-gain differential amplification to increase the voltage presented at its input. The LM324 belongs to the general-purpose amplifier segment of the larger voltage-feedback operational-amplifier hierarchy. Internally compensated amplifiers simplify closed-loop design because no external frequency-compensation components are required for ordinary gain configurations. Four independent amplifiers in one package reduce board area and component count in multi-channel sensor, filtering, buffering, and control circuits. The verified product information identifies four amplifier circuits, a 1.2 MHz gain-bandwidth product, a 3 mV offset-voltage rating, and operation from a supply as high as 30 V. The internal compensation supports stable operation in standard noninverting and inverting amplifier arrangements. Because the LM324AD is a general-purpose device, design engineers should treat it as a cost-conscious solution rather than a precision op amp with rail-to-rail outputs, low offset over temperature, or very low noise. Common uses include buffering sensor outputs, amplifying low-level control signals, active filtering, differential signal conditioning, and driving ADC input stages. The four independent channels can process separate analog signals or implement stages such as a two-stage filter or transimpedance-style front end. Single-supply operation is particularly useful in industrial controls, embedded instrumentation, educational electronics, and simple battery-powered systems where a negative rail is unavailable. When using the LM324AD, verify input and output common-mode limits, output-current capability, load impedance, and stability under the selected closed-loop gain before finalizing the design. Place input and output compensation or decoupling components close to the relevant pins, keep sensitive input routing away from switching nodes, and include adequate bypassing on the power supply. The 14-pin SOIC package also requires attention to thermal pad-free layout and copper continuity when operating at high ambient temperatures. This product page combines verified manufacturer and distributor information, lifecycle-oriented sourcing details, same-footprint alternatives, and practical design guidance. It adds a same-package comparison framework and implementation notes that are more useful for PCB and sourcing decisions than a distributor listing alone.

RFQ پەیوەندی
LM324ADBR - 30V 1.2MHz Quad Op Amp | Texas Instruments
LM324ADBR

LM324ADBR - 30V 1.2MHz Quad Op Amp | Texas Instruments

The Texas Instruments LM324ADBR is a four-circuit general-purpose operational amplifier rated for a 30 V maximum supply, 1.2 MHz gain-bandwidth product, and 3 mV input offset voltage. The device is packaged in a 14-pin SSOP (DB) package and is intended for low-frequency signal conditioning, current-to-voltage conversion, and general amplifier applications operating from a single or dual supply. An operational amplifier is a high-gain differential amplifier whose closed-loop behavior is established primarily by external feedback components. The LM324A family combines four amplifiers in one package, placing it in the operational-amplifier hierarchy alongside instrumentation, buffer, and comparator circuits while remaining part of the broader analog and power-management semiconductor ecosystem. Its common-mode input range allows the device to operate from single-supply or split-supply systems. The LM324ADBR supports a 3 V to 32 V total supply range, has an approximately 1.2 MHz gain-bandwidth product, and specifies a maximum input offset voltage of 3 mV. The package operates from 0°C to 70°C, making the standard A-grade ordering option suitable for commercial and industrial equipment where extended-temperature operation is not required. Its four independent channels can implement non-inverting, inverting, summing, difference, and comparator functions. Each channel uses a bipolar transistor input stage and an internally compensated architecture. Internal compensation removes the need for an external frequency-compensation capacitor in ordinary closed-loop operation. The 65 dB common-mode rejection and 16 V output swing support precision conditioning of mid-level signals, while the 60 mA per-channel output-current capability provides useful drive for higher-impedance loads. Typical uses include sensor signal conditioning, low-side current measurement, audio preamplification, transducer interfaces, and general DC signal amplification. The quad configuration also allows a single package to implement a complete instrumentation channel, such as a two-op-amp differential stage plus two buffer or gain stages. The device is especially suitable where a supply voltage above 5 V is available but a rail-to-rail input or output is unnecessary. Designers should verify common-mode input and output swing against the actual signal range, provide adequate bypassing close to the supply pins, and account for input offset and bias currents in high-impedance measurements. A stable feedback network and adequate output-load capability are also important because the LM324A is optimized for general-purpose, low-frequency precision rather than high-speed or rail-to-rail performance. This product page combines the Texas Instruments ordering information, package and electrical characteristics, sourcing guidance, and practical design considerations into a focused engineering reference. It also identifies same-footprint family options and explains the trade-offs when comparing the LM324A with lower-cost or lower-performance amplifier implementations.

RFQ پەیوەندی
LM324ADE4 - Quad 1.2MHz Op Amp | Texas Instruments | SOIC-14
LM324ADE4

LM324ADE4 - Quad 1.2MHz Op Amp | Texas Instruments | SOIC-14

Texas Instruments LM324ADE4 is a quad general-purpose operational amplifier with four independent, internally frequency-compensated amplifiers, 1.2 MHz gain-bandwidth product, and 0.5 V/µs slew rate in a 14-pin SOIC package. The device operates from a single supply or split supplies, with the listed operating range extending to ±16 V. An operational amplifier is an analog signal-conditioning IC that compares two input voltages and amplifies their difference through high open-loop gain. The LM324ADE4 belongs to the operational-amplifier hierarchy within amplifier ICs and analog semiconductors. Its four independent channels allow one package to provide feedback control, buffering, level shifting, summation, and general analog amplification without requiring four separate amplifier packages. The four amplifiers feature internally frequency compensation, allowing operation as stable unity-gain buffers without external compensation components. A 1.2 MHz gain-bandwidth product and 0.5 V/µs slew rate support audio-band and general-purpose closed-loop applications. The device also supports operation from a single positive supply as well as split bipolar supplies, making it useful in mixed industrial, instrumentation, control, and consumer circuits. The 14-SOIC package is pin-compatible with the established LM324 family arrangement, which simplifies repair, prototyping, and board reuse. Each amplifier has differential inputs, an output, and power connections, with the package distributing those functions across four channels. Because the amplifiers are independent rather than sharing internal output stages, each channel can be used for a separate signal path or left unused when its input and output are properly configured. Typical uses include sensor-signal conditioning, low-current motor and actuator drivers, audio preamplification, analog summing networks, threshold detection, and general instrumentation. The 1.2 MHz bandwidth is adequate for many audio and control signals, but designs requiring substantially higher bandwidth, lower offset voltage, faster settling, or lower noise should use a more specialized amplifier family. Design carefully around input common-mode range, output swing, input bias current, and the limits of each amplifier channel. Keep sensitive inputs away from noisy return paths, observe the recommended bypass capacitors at the supply pins, and avoid operating near the output saturation limits. The manufacturer datasheet should guide input/output protection, supply decoupling, unused-channel configuration, and maximum input and output voltage conditions. This product page combines the LM324ADE4 operating parameters, package details, practical application guidance, pin-focused design considerations, and qualified drop-in alternatives. It is intended to help engineers identify where this economical quad general-purpose amplifier fits and where a higher-performance or application-specific amplifier is more appropriate.

RFQ پەیوەندی