Amplifier ICs
بەرهەمەکان (3,200+)
LM2904S-13 - Dual 1.1MHz Op Amp, 100dB Gain | Diodes
The Diodes Incorporated LM2904S-13 is a dual general-purpose operational amplifier packaged in an 8-pin SO package. It provides two independent amplifier channels, a listed gain bandwidth product of 1.1 MHz, a listed open-loop gain of 100 dB, and input bias current of 20 nA. The device is intended for single-supply or split-supply operation across industrial temperature conditions. An operational amplifier is a high-gain, differential-input analog amplification component used to compare or amplify voltage signals. Within the electronics hierarchy, the LM2904 belongs to the operational-amplifier family, which sits within analog amplifier ICs and broader semiconductor signal-conditioning products. Its two-channel configuration allows one device to implement two related analog functions while reducing the number of components required on a circuit board. The manufacturer datasheet identifies the LM2902 and LM2904 series as low-input-offset-voltage amplifiers designed for single power-supply operation over a wide voltage range, with split-supply operation also possible. The operating-temperature characterization extends from -40°C to +125°C. The standard green mold compound, industry-standard pinout, and SO-8 packaging support use in conventional industrial, instrumentation, control, and signal-conditioning equipment. The 1.1 MHz gain bandwidth product makes the device appropriate for low-frequency amplification rather than high-speed signal processing. Its 100 dB open-loop gain provides substantial nominal gain before feedback and saturation limits are considered. The 20 nA input bias-current listing is also relevant when the source impedance is high, because bias-current error can become significant relative to the input voltage being measured. Typical uses include transducer-signal conditioning, feedback networks in control systems, active filtering, sensor amplification, and general-purpose analog signal conditioning. Two amplifiers in one package are useful when a design needs an inverting stage and a non-inverting stage, two sensor channels, or an amplifier paired with a comparator-like buffer function. Designers should verify input common-mode range, output swing, output-current capability, offset voltage, and supply-current limits in the manufacturer datasheet before finalizing a new board. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be biased so that both output stages remain in a defined operating state. This product page combines the manufacturer family data with practical application guidance, a same-package family alternative, and engineering-focused selection criteria. It is intended to help engineers determine whether the LM2904S-13 is appropriate for a low-frequency, dual-amplifier design before moving to detailed electrical verification and PCB implementation.
LM2904ST Low-Power Dual Op Amp | STMicroelectronics
STMicroelectronics LM2904ST is a low-power dual operational amplifier packaged in an 8-pin MiniSO package. It contains two independent, internally frequency-compensated amplifiers, allowing one device to implement two separate analog signal-processing channels. The LM2904 family is intended for general-purpose applications where a dual amplifier, low power consumption, and straightforward circuit implementation are more important than low-noise or high-speed performance. An operational amplifier is an active semiconductor device that compares two input voltages and drives its output to amplify the difference between them. In a closed-loop configuration, negative feedback causes the output to follow the intended circuit function with very high input impedance and relatively low output impedance. The LM2904 belongs to the operational-amplifier hierarchy, where it sits below precision amplifiers, rail-to-rail amplifiers, and high-speed amplifiers while remaining appropriate for industrial control, sensor conditioning, audio, and general instrumentation. The LM2904ST provides two amplifier channels in one package, reducing component count and PCB space compared with two separate single-channel amplifiers. Its internally implemented frequency compensation simplifies circuit design by eliminating the need for external compensation components in standard closed-loop applications. Because both channels are independent, the device can support different signal paths, provided the designer observes the common power-supply and grounding requirements. The target LM2904ST is a standard general-purpose dual amplifier in the MiniSO-8 format. The STMicroelectronics LM2904 family also includes other package and performance options, so engineers should compare electrical ratings, temperature range, supply limits, input common-mode range, output swing, and automotive qualification before treating another family member as a drop-in replacement. The exact electrical limits and environmental classifications should be confirmed in the manufacturer datasheet for the selected ordering code. Typical uses include low-frequency sensor signal conditioning, control-loop amplification, active filtering, audio preamplification, transducer interfaces, and general buffer stages. In such circuits, the LM2904ST provides two independently usable channels while keeping the implementation compact. Its internal compensation makes conventional inverting, non-inverting, summing, and differential amplifier configurations straightforward, although output loading, source resistance, stability margins, and the input common-mode range still require careful review. For a new layout, place the device close to the signals it processes, maintain a low-impedance return path to the supply ground, and decouple the supply pins locally. Avoid sensitive-source connections next to the output or supply pins, because parasitic coupling can increase offset and distortion. This product overview combines the manufacturer family information, package identity, pin assignment, sourcing considerations, and drop-in-replacement guidance to support faster engineering selection and PCB planning.
LM2904TH-13 - Dual 700 kHz Op Amp | Diodes Incorporated
Diodes Incorporated LM2904TH-13 is a dual general-purpose operational amplifier in an 8-pin TSSOP package. The device contains two independent high-gain amplifiers, supports a 700 kHz bandwidth, and is designed for operation from a single supply or from split supplies. The LM2904 family provides a practical choice for signal conditioning, feedback control, and analog circuit designs requiring two amplifiers in one package. An operational amplifier, commonly called an op amp, is a high-gain DC-coupled analog amplifier whose behavior is controlled by feedback around the device. The LM2904 combines two independent amplifier channels in one package, reducing board area compared with two separate single-amplifier devices. Its 8-pin TSSOP package supports compact surface-mount assemblies and exposes supply, input, and output connections for each channel. The most prominent specified characteristics are the two-amplifier configuration, 700 kHz bandwidth, and supply capability extending to ±18 V, equivalent to a 36 V total span. The device is categorized as a standard general-purpose amplifier and is designed for both single-power-supply and split-supply operation. Its architecture also targets low input-offset voltage, making it relevant to closed-loop amplifier and comparator-style signal-processing applications when configured appropriately. The LM2904 series combines independent high-gain operational amplifiers with a broad supply-voltage range. Because the two channels are independent, one channel can process a sensor signal while the other performs an active filter, level conversion, or feedback function. Common-mode and output-voltage limitations still depend on the selected supply voltages, so every analog signal path must remain inside the amplifier’s valid input and output ranges. Typical uses include low-frequency instrumentation, buffered sensor interfaces, audio preamplification, analog gain stages, and dual-axis control loops. The 700 kHz bandwidth is most appropriate for general-purpose signal paths rather than high-speed video, RF, or precision data-conversion applications. Split-supply operation can simplify bipolar signal handling, while single-supply operation may require input and output biasing around the midpoint of the supply. Designers should use the manufacturer’s pin-description and typical-application information to establish channel assignments, bypass-capacitor placement, and acceptable output-load conditions. Decouple each supply rail close to the device, keep feedback paths short, and verify that input common-mode voltage and output swing remain valid over the full supply range and temperature range intended for the design. This page organizes the key device characteristics, practical application guidance, verified pricing references, pin-location information, and same-footprint replacement options. It also distinguishes documented LM2904 family choices from alternatives that would require a different package or different electrical capabilities, helping engineers narrow a redesign without overlooking PCB compatibility.
LM2904VDMR2 - Dual 3-32V Op Amp for Industrial Control
The onsemi LM2904VDMR2 is a dual general-purpose operational amplifier with a 3 V to 32 V supply range, 1 MHz gain-bandwidth product, and 8-MSOP package. Designed for low power consumption, the device accepts single-supply or split-supply operation, while its common-mode input voltage range can extend to ground or VEE. It is suited to industrial signal-conditioning, transducer, and analog-control systems. An operational amplifier is a voltage-gain building block used to amplify small signals, buffer sensors, compare voltages, and implement active analog filters. The dual LM2904 family combines two amplifiers in one package, reducing board area compared with separate single amplifiers. Its ability to operate from a single positive supply or from split positive and negative rails gives it broad utility in both grounded-signal systems and bipolar analog environments. Key features include low power drain, a 1 MHz gain-bandwidth product, and a common-mode input range that extends to ground or VEE. The 3 V to 32 V operating range supports both conventional 5 V and 24 V industrial systems when the total supply remains within the rated range. The 8-MSOP surface-mount package also supports compact, high-density analog boards while providing adequate lead spacing for automated assembly and inspection. The LM2904 architecture derives from the circuit design used in onsemi's quad operational-amplifier family. It is intended for general-purpose applications where low power consumption and flexible supply configurations are more important than precision, rail-to-rail input/output performance, or the bandwidth of modern CMOS amplifiers. Because the input common-mode range can reach ground or VEE, the device can process signals near the lower supply rail when correctly biased. Typical applications include 0–5 V or 0–10 V industrial sensor interfaces, low-level transducer amplification, analog alarm and threshold circuits, active low-pass filters, and general control-signal conditioning. It may also be used in battery-powered instrumentation where the selected operating point must balance signal bandwidth against power drain. Split-supply operation is useful for bipolar sensor signals or analog stages that require both positive and negative swing around ground. When designing around the LM2904VDMR2, verify input and output voltage limits at the selected supply voltage and load. Input and output decoupling should be placed close to the device, and unused amplifier channels must be configured according to the manufacturer’s recommended stable operating conditions. Avoid relying on rail-to-rail behavior, and account for input offset and bias-current errors when designing high-accuracy signal chains. This product page consolidates the confirmed supply, bandwidth, package, and application characteristics with drop-in replacement analysis, package comparison, and practical circuit guidance. It helps engineers distinguish genuine footprint-compatible options from amplifiers that are only functionally similar before committing a new board revision.
LM2904VDMR2G - Dual 1MHz Op Amp, 3-32V | onsemi
onsemi LM2904VDMR2G is a dual general-purpose operational amplifier with two independent channels, 1 MHz gain-bandwidth product, and a 3 V to 32 V supply range in an 8-pin MSOP package. Designed for single-supply or split-supply operation, it accepts input common-mode voltages extending toward ground or VEE, making it suitable for industrial, automotive, battery-powered, and signal-conditioning systems. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to compare an input signal with a feedback network. The LM2904 family combines low power consumption, internal frequency compensation, and common-mode input capability reaching ground or VEE. Its dual-channel configuration places two independent amplifiers in one package, reducing component count in applications requiring matched signal paths, sensing, buffering, or error amplification. The principal features are a 3 V to 32 V operating range, approximately 1 MHz gain-bandwidth product, dual-circuit construction, and support for single or split supplies. The common-mode input range is particularly useful in battery systems because the amplifier can operate close to the negative supply rail. Its MSOP-8 package supports compact layouts, while the low-power operating characteristics suit portable and industrial-control equipment. Internally frequency-compensated channels remove the need for an external compensation network in ordinary closed-loop gain configurations. Each channel can operate independently, allowing simultaneous use as two amplifiers. Designers must still observe output-swing, input-voltage, supply-current, and common-mode limits. Configuration as a voltage follower, non-inverting amplifier, or inverting amplifier will determine signal gain and feedback-component values. Typical applications include sensor-interface conditioning, low-side current measurement, industrial control loops, battery-powered monitoring, transducer amplification, and general-purpose analog signal processing. The split-supply capability is useful when bipolar sensor signals must be amplified around ground. In single-supply systems, the ground-reaching common-mode range helps simplify biasing near the lower rail. A key design consideration is to verify output swing under the intended load and to place input and feedback components close to their pins to minimize parasitic pickup. Decoupling capacitors should connect directly between each supply pin and ground. Stable operation should be confirmed across supply voltage, temperature, output loading, and the selected gain because the internal compensation does not remove all application-level stability constraints. This page combines electrical characteristics, package information, drop-in alternatives, comparison parameters, and practical circuit guidance to accelerate component selection. It supports engineers comparing general-purpose dual amplifiers for industrial, automotive, and low-voltage analog systems while emphasizing the need to verify exact pinout, qualification, and operating limits before substitution.
LM2904VDR2G - Dual 1MHz Op Amp | onsemi | Industrial
The onsemi LM2904VDR2G is a dual, general-purpose operational amplifier with a 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, and operation from single or split supplies in an 8-SOIC package. It is designed for instrumentation, signal conditioning, buffer amplification, and general analog control applications where two amplifiers are required in one package. An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify a voltage difference. The LM2904 family belongs to the operational-amplifier hierarchy, with the LM358 family representing one-half of a quad amplifier. Its common-mode input range extends to ground or VEE, allowing useful operation in single-supply circuits where the input signal approaches the negative supply rail. Key features include two amplifier circuits per package, a 1 MHz gain-bandwidth product, a 0.6 V/µs slew rate, and a specified operating voltage range of up to ±16 V, equivalent to 32 V across the supply rails. The low-power design supports both single-supply and split-supply operation. The standard 8-SOIC package also simplifies assembly in designs that do not require a high-performance precision amplifier. The LM2904 architecture is intended for general-purpose amplification rather than rail-to-rail input or output operation. Its common-mode input behavior reaches ground or VEE, making it particularly useful for circuits powered from a positive rail and ground. As with any feedback amplifier, stable operation depends on suitable compensation, output loading, source impedance, and the selected gain network. Typical uses include buffering sensor outputs, amplifying low-level analog signals, conditioning potentiometer inputs, driving moderate loads, building active filters, and providing general-purpose gain stages in industrial or embedded systems. Two amplifiers in one SOIC package can also simplify layouts where matched general-purpose stages are needed. When designing around the LM2904, check the common-mode input range and output swing at the intended load rather than assuming rail-to-rail behavior. Place input and feedback components close to the device, provide adequate bypassing near the supply pins, and verify stability at the lowest planned gain. The manufacturer datasheet should guide compensation, load capability, and absolute maximum ratings. This product page combines the exact LM2904VDR2G package and electrical identity with practical design guidance, pin-level information, verified source links, and a package-matched replacement comparison. These engineering details help buyers distinguish the dual general-purpose amplifier from single-amplifier, automotive-qualified, and other LM-family variants before committing to a PCB design.
LM2904VN - Dual Op Amp, 1MHz GBW, PDIP-8 | onsemi
The onsemi LM2904VN is a single-supply dual operational amplifier featuring two independent general-purpose op-amp circuits with a 1 MHz gain-bandwidth product, a 0.6 V/us slew rate, and operation from a 3 V to 26 V supply (up to 32 V total, or +/-1.5 V to +/-16 V split supplies), housed in an 8-pin PDIP (0.300 inch, 7.62 mm) through-hole package. A dual operational amplifier integrates two matched, frequency-compensated op-amp cores on a single silicon die within one package. As a subcategory of the linear amplifier family, general-purpose op-amps sit within the broader hierarchy of voltage amplifiers and analog signal-conditioning ICs, providing gain, buffering, filtering, and comparison functions in analog front ends. The dual configuration halves board space and improves channel-to-channel matching compared with two single op-amps. Key features include low power drain, a common-mode input voltage range that extends to ground/VEE (input common-mode includes the negative rail), and single-supply or split-supply operation. These characteristics let designers build ground-referenced signal conditioning directly from a single positive rail without a negative supply, which is the defining advantage of the LM358/LM2904 amplifier family. Technically, the LM2904VN derives from the circuit design perfected for the industry-standard LM324 quad op-amp: the LM358 series is equivalent to one-half of an LM324. The amplifier delivers approximately 70 dB of open-loop gain, low input bias current (about 45 nA typical per distributor characterization data), and internal frequency compensation that guarantees unity-gain stability without external components. Typical applications include transducer amplifiers, DC gain blocks, active filters, comparators, and general low-frequency signal conditioning in industrial controls, automotive subsystems, and battery-powered instruments. A key design consideration: the output stage is not rail-to-rail and can sink only limited current near ground, so loading the output with a resistor to VEE (for example, 2 kOhm) improves output swing close to the negative rail. This page adds value beyond the manufacturer datasheet by consolidating drop-in cross-references, a parameter comparison table against pin-compatible alternatives, and practical design notes in one place.
LM2904VNG - Dual 30V Operational Amplifier | onsemi
onsemi LM2904VNG is a dual, general-purpose operational amplifier designed for single-supply or split-supply operation, with a stated supply range of 3 V to 26 V or up to 32 V depending on the specific device specification source. It contains two independent, high-gain, frequency-compensated amplifiers and is packaged in an 8-pin PDIP package. The LM2904 family is based on the circuit designs used in the LM358 series, which provides a practical family relationship for signal conditioning and general-purpose analog designs. The device is listed by onsemi and is associated with a 0.6 V/µs slew rate and 1 MHz gain-bandwidth product in the retrieved component description. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages while using external feedback to define the closed-loop gain. The dual configuration provides two amplifier channels in one package, making it useful for signal conditioning, buffering, filtering, transducers, instrumentation, and control applications. The LM2904VNG operates from a single supply or split supply, and its common-mode input voltage range extends to ground or VEE. This makes it appropriate for circuits that use low-voltage sensing or single-rail power arrangements where the input signal approaches the lower supply rail. Key characteristics include two amplifier circuits, a general-purpose amplifier type, 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, operation from 3 V to 32 V, and an 8-pin PDIP package. The package is specified as an 8-DIP measuring 0.300 inches, or 7.62 mm, in pitch. The component is identified as a tube-packaged part in the retrieved datasheet description, making it suitable for conventional through-hole PCB assembly rather than surface-mount reflow. The LM2904 family is commonly selected when a design requires a dual amplifier with broad supply-voltage capability and flexible supply configurations. Its internally frequency-compensated architecture simplifies the construction of standard amplifier stages, while the common-mode input range extending toward ground or VEE supports single-supply sensor interfaces. The operating-amplifier category sits within analog integrated circuits and broader signal-chain design, where the device can sit between sensors, analog converters, filters, and actuator drivers. Typical applications include low-side current or voltage sensing, audio and communications signal conditioning, industrial control modules, regulated power-supply feedback, and general dual-stage amplifier boards. In an instrumentation circuit, the two channels can amplify or buffer two related signals, while in a control system they can monitor a feedback signal and drive a downstream conditioning stage. The device should be selected only after checking the exact onsemi datasheet for input common-mode limits, output swing, output-current capability, electrical characteristics, and package details. The principal design consideration is supply and signal-headroom management. Although the LM2904 family supports single-supply operation, the usable output range and input common-mode range are not identical to the supply range. Resistor networks, decoupling capacitors, and careful grounding should be selected according to the manufacturer application guidance. This page combines the exact package, amplifier, voltage, bandwidth, slew-rate, and supply information shown in the component records with practical guidance for evaluating the LM2904VNG in industrial, communications, audio, sensor, and power-control designs.
LM2904VQDR - Dual 30V 700kHz Op Amp | Texas Instruments
The Texas Instruments LM2904VQDR is a dual, general-purpose operational amplifier with a 30 V supply rating, 700 kHz gain-bandwidth product, and operation from -40 °C to 125 °C, supplied in an 8-pin SOIC package. The LM2904VQDR combines two amplifier channels in one package, making it suitable for signal conditioning, transducer amplification, and general analog control applications where a wide supply range and automotive-capable temperature operation are important. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. Its place in the signal-chain hierarchy is amplifier IC → operational amplifier → analog signal-conditioning IC → semiconductor. A differential input stage, high open-loop gain, and internally compensated design allow the device to form stable closed-loop gain stages with external resistors or capacitors. Key features include two amplifier circuits per package, a 700 kHz gain-bandwidth product, and a maximum supply rating of 30 V. The bipolar architecture supports conventional general-purpose applications using single or split supplies. An 8-pin SOIC body measures 0.154 inches wide and 3.90 mm in body width. The manufacturer identifies the LM2904V family as an enhanced alternative to the original LM2904, with operation extending to 125 °C. The 700 kHz gain-bandwidth product makes the amplifier suitable for low-frequency instrumentation and feedback-control loops rather than high-speed signal chains. Because both channels share one package, grounding and supply-decoupling practices apply to the complete device, and unused channels should be configured according to the manufacturer's recommended stable-input circuit. Typical uses include industrial sensor interfaces, audio preamplifier stages, current-to-voltage converters, active filters, and power-supply feedback loops. The wide operating range also supports automotive and rugged industrial equipment when the board design, external components, and qualification requirements meet the application specification. A key design consideration is common-mode and output-swing headroom. Review the input common-mode range and output voltage limits in the manufacturer datasheet for the chosen supply voltage. Decouple each supply pin locally, route feedback connections away from high-current switching nodes, and verify stability with the exact source and load impedances used in production. This page combines the LM2904VQDR family specifications, package information, pin-compatible alternatives, application guidance, and design notes to help engineers qualify the amplifier and plan a board-level replacement without relying on a single parameter listing.
LM2904VQDRG4 - Dual 30V 700kHz Op Amp | Texas Instruments
Texas Instruments LM2904VQDRG4 is a dual general-purpose operational amplifier with a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and low quiescent current of 500 µA per channel. The device is packaged in an 8-pin SOIC (D) package and operates from -40°C to 125°C. Two independent amplifiers in one package support signal conditioning, current sensing, voltage buffering, and general feedback-control circuits. An operational amplifier, or op amp, is a high-gain differential amplifier whose external feedback network determines its closed-loop behavior. A dual op amp combines two amplifiers in one package, reducing board area when a circuit needs two related analog functions. Within the broader semiconductor hierarchy, an op amp is an analog integrated circuit used for linear amplification, filtering, comparison, and feedback control. The LM2904VQDRG4 is intended for general-purpose applications rather than precision or high-speed signal chains. Its 700 kHz gain-bandwidth product is suitable for low-to-moderate bandwidth amplification, while the 30 V supply rating allows operation from single or dual supplies. A 500 µA per-channel quiescent current helps limit power consumption in battery-operated and low-power equipment. The broad -40°C to 125°C operating range supports industrial and automotive environments. Each channel can be configured as an inverting amplifier, non-inverting amplifier, voltage follower, comparator, or active-filter building block. Common-mode and output-drive behavior must be checked against the specific operating point because the LM2904V trades precision and bandwidth for wide supply-voltage tolerance and low quiescent current. The dual configuration is particularly useful when a board requires gain in one signal path and buffering or active filtering in another. Typical uses include transducer-signal conditioning, 4-20 mA current-loop receivers, low-side current sensing, sensor amplification, power-supply feedback, audio preamplification, and industrial control loops. The device is also suitable for battery-powered instrumentation because its low quiescent current reduces the supply burden when both channels are not continuously active. Design layouts should keep input and feedback traces short, place input-biasing resistors close to the amplifier pins, and avoid routing high-current switching paths beneath the SOIC footprint. Decoupling capacitors should be connected with minimal loop area, and unused amplifier channels should be configured according to the Texas Instruments datasheet rather than left open. Verify input and output swing, common-mode range, output-current capability, and stability for every selected feedback network. This product page combines the Texas Instruments family specifications, exact MPN packaging details, lifecycle-oriented sourcing guidance, and application-focused design guidance. It also highlights the need to distinguish verified drop-in alternatives from electrically similar devices that require different packages or different pin assignments.
LM2904VQDRG4Q1 - 26V Dual Op Amp | Texas Instruments
Texas Instruments LM2904VQDRG4Q1 is an automotive-grade, dual general-purpose operational amplifier with a 26 V supply range, 700 kHz gain-bandwidth product, and 8-pin SOIC package. The device provides two amplifier channels in one package and is qualified to AEC-Q100 specifications for automotive applications. Its operating temperature range extends from -40°C to 125°C. An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its non-inverting and inverting inputs. The dual-amplifier configuration places two independent general-purpose amplifier channels in a common 8-pin SOIC package. Within the broader semiconductor hierarchy, this component is an operational amplifier, analog amplifier IC, and signal-conditioning IC commonly used to buffer sensors, amplify low-level signals, and support feedback-based circuit functions. The principal characteristics include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, maximum input offset voltage of 3 mV, and approximately 500 µA supply-current consumption per channel. These values make the LM2904VQDRG4Q1 appropriate for general-purpose analog signal paths where modest bandwidth, stable DC behavior, low quiescent current, and automotive qualification are more important than high-speed or precision performance. Each channel contains an input stage, differential amplification function, and push-pull output stage designed for feedback operation. The 26 V total supply capability supports higher-voltage analog systems than common 5 V and 12 V precision amplifier families. Its 700 kHz gain-bandwidth product limits closed-loop bandwidth according to the selected noise gain, while the 0.3 V/µs slew rate limits large-signal transition speed. Applications must also observe the device's common-mode input, output swing, output-current, and stability limits from the manufacturer datasheet. Typical uses include automotive sensor interfaces, low-frequency active filters, transducer signal conditioning, analog monitoring channels, and general-purpose buffering. The two channels can process related signals in one package, simplifying dual-channel analog front ends. In feedback networks, resistor ratios establish closed-loop gain, while output loading and source impedance determine practical bandwidth and stability performance. A critical design consideration is power-supply bypassing. Place a suitable decoupling capacitor close to the supply pins and connect the ground return directly to the ground plane. Confirm input common-mode voltage, output swing, load current, and noise-gain stability against the datasheet limits before using the amplifier with large capacitive loads or high source impedances. This product page combines the exact automotive ordering information, package and electrical characteristics, qualified drop-in alternatives, and practical design guidance into one engineering reference. It is intended to accelerate component selection, PCB footprint confirmation, and analog-circuit qualification for automotive and industrial designs.
LM2904VQDRQ1 - Dual 30V 700kHz Op Amp | Texas Instruments
The Texas Instruments LM2904VQDRQ1 is a dual general-purpose operational amplifier rated for a 30 V total supply voltage, 700 kHz gain-bandwidth product, and operation from -40°C to 125°C. The device is offered in an 8-pin SOIC package and is qualified to AEC-Q100 for automotive applications. Each channel provides independent input and output connections, allowing the amplifier to implement two signal-processing functions or to remain available for additional circuit requirements. An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify the difference between two input voltages. The LM2904 family belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its dual-channel architecture makes it useful for general-purpose signal conditioning, buffering, feedback amplification, voltage comparison, and instrumentation functions where a wide supply-voltage range and elevated-temperature capability are valuable. The principal performance characteristics include two amplifier channels, a 700 kHz gain-bandwidth product, and a maximum total supply voltage of 30 V. The manufacturer identifies the LM2904VQDRQ1 as an automotive AEC-Q100-qualified dual operational amplifier in an 8-SOIC package. It also has a high-gain configuration suitable for closed-loop amplifier stages and comparator-like functions. These characteristics position it between precision low-noise amplifiers and high-speed wideband amplifiers: it provides more bandwidth than a basic general-purpose amplifier while retaining a simple, industry-standard package. The LM2904V product family uses conventional internal compensation and is intended for general-purpose operation rather than rail-to-rail input or output designs. Its supply-voltage tolerance permits operation from automotive and industrial battery-derived rails, although each application must remain within the device's absolute maximum and recommended operating limits. Because both amplifiers share the same package, their power rails are common, while the signal inputs and outputs remain independent. Typical automotive uses include low-frequency sensor conditioning, actuator signal interfaces, active filtering, and general control-system analog channels. The same device can support industrial instrumentation, audio and communications interfaces, and voltage-feedback amplifier stages. For dual-rail designs, the two channels can process related or unrelated signals, allowing a more compact implementation than two separate single-channel amplifiers. Designers should verify input and output common-mode ranges, output swing, stability with the selected feedback network, and noise performance against their signal bandwidth. The SOIC outline also requires attention to exposed copper and thermal dissipation when operating continuously near the upper temperature limit. Bypass capacitors should be placed close to the supply pins, and sensitive input traces should remain short and away from switching nodes. This product page combines the exact ordering information, operating limits, package details, automotive qualification, pin assignment, qualification alternatives, and application-oriented design guidance for LM2904VQDRQ1. It is intended to help engineers determine whether this dual, 30 V, 700 kHz operational amplifier fits a new design or can be introduced through a controlled board-level replacement process.
LM2904VQPWR - Dual 30V 700kHz Op Amp | Texas Instruments
The Texas Instruments LM2904VQPWR is a dual, general-purpose operational amplifier designed for operation from a 30 V supply with a 700 kHz gain-bandwidth product. The device contains two independent, high-gain, frequency-compensated amplifiers and is offered in an 8-pin TSSOP (PW) package. Its operating temperature range extends from -40 °C to 125 °C. An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 family sits within the broader hierarchy of operational amplifiers, analog amplifiers, amplifier ICs, and semiconductors. It can operate from either a single supply or split supplies, making it suitable for circuits powered by industrial rails, batteries, or dual bipolar rails. The two amplifiers can be used independently for separate signal paths or together in differential, filtering, feedback, and gain-control configurations. The 30 V maximum supply rating provides ample headroom for higher-voltage analog systems, while the 700 kHz bandwidth supports general-purpose signal amplification rather than high-speed precision applications. Its wide -40 °C to 125 °C temperature range allows operation across industrial, automotive-adjacent, and extended-temperature equipment when the system qualification requirements are satisfied. The LM2904VQPWR uses internal frequency compensation to maintain stable operation in common closed-loop configurations without requiring an external compensation network. Because it contains two amplifier sections, it can reduce component count and board area in designs that require two similar analog channels. Each section has independent input, output, supply, and ground connections, allowing normal dual-amplifier layouts. Typical uses include sensor-signal conditioning, low-frequency active filters, audio preamplification, motor and actuator feedback loops, and general industrial control interfaces. For battery-powered or split-supply equipment, its dual-amplifier organization can support two related analog channels while sharing one package. Engineers should still verify output swing, input common-mode range, load drive, stability, and noise for the intended feedback network. PCB implementation requires careful decoupling and grounding. Place the supply bypass capacitor close to the positive and negative supply pins, connect the exposed package ground as applicable, and keep feedback resistors close to the relevant amplifier inputs and outputs. Avoid routing high-current return paths through the analog ground reference. Verify the selected operating point against the manufacturer datasheet, especially when output swing approaches the supply rails. This product page combines the manufacturer ordering information, verified distributor listings, package details, drop-in alternatives, comparison parameters, and practical PCB guidance. It is intended to accelerate component selection while directing critical electrical verification to the Texas Instruments LM2904V datasheet and product documentation.
LM2904VQPWRG4 - Dual 30 V 700 kHz Amp | Texas Instruments
The Texas Instruments LM2904VQPWRG4 is a dual general-purpose operational amplifier with two independent, internally frequency-compensated amplifiers, a maximum supply rating of 30 V, and 700 kHz gain-bandwidth product. Each amplifier is supplied in an 8-pin TSSOP package, allowing both channels to be placed on one compact surface-mount device. An operational amplifier is a high-gain, analog signal-processing component that compares two input voltages and drives its output to reflect their difference. The LM2904V family belongs to the operational-amplifier hierarchy within analog amplifiers and broader integrated-circuit signal conditioning. This dual-device arrangement supports independent inverting, noninverting, summing, filtering, comparison, and feedback-amplifier configurations without requiring two separate packages. The LM2904VQPWRG4 provides a 30 V maximum supply rating and operates across a -40°C to 125°C temperature range. Its 700 kHz gain-bandwidth product makes it appropriate for general-purpose signal paths with moderate bandwidth requirements. The manufacturer also identifies a low typical supply-current drain of 0.7 mA and a common-mode input range that includes ground, which is useful for sensing signals near the lower supply rail. Each channel uses independent, frequency-compensated architecture. This arrangement lets one amplifier process a low-level sensor signal while the second handles a separate control, buffer, or gain stage. The 8-pin TSSOP package reduces board area compared with two individual single-amplifier packages, although users still need to observe normal operational-amplifier stability rules when driving capacitive loads or operating with unusual noise-gain configurations. Typical applications include industrial sensor interfaces, low-frequency active filters, transimpedance stages, audio preamplifiers, loop-control blocks, and general instrumentation. The common-mode range including ground supports rail-adjacent sensing, while the extended temperature range permits use in industrial and automotive-style control environments when the application satisfies the device's complete electrical and qualification requirements. Designers should verify input and output voltage limits against the selected supply arrangement, provide adequate bypass capacitance near the supply pins, and confirm stable operation at the intended gain and load. The exact pin functions and recommended application circuit should be taken from the manufacturer pin-description table before assigning PCB tracks. This product overview combines the LM2904VQPWRG4 device identity, manufacturer specifications, packaging details, comparison context, and practical implementation guidance to support faster component selection and board-level implementation.
LM2904VQPWRG4Q1 - Dual 26V 700kHz Op Amp | Texas Instruments
Texas Instruments LM2904VQPWRG4Q1 is an AEC-Q100-qualified, dual general-purpose operational amplifier rated for 26 V total supply operation, with two independent, internally frequency-compensated amplifier channels in an 8-pin TSSOP package. Each channel supports single-supply operation from 3 V to 26 V and split-supply operation when the total supply difference is between 3 V and 26 V. The device operates at a gain-bandwidth product of 700 kHz while drawing a typical supply current of 0.7 mA. An operational amplifier is an analog signal-conditioning semiconductor that amplifies the voltage difference between its differential inputs. The LM2904 family belongs to the broader hierarchy of operational amplifier, analog amplifier, signal-conditioning IC, and semiconductor. Its two independent channels allow one package to process two signals, reducing board area in automotive and industrial control systems without requiring separate single-channel amplifier packages. The principal features include two independent high-gain amplifiers, internal frequency compensation, a common-mode input range that includes ground, and operation from a single or split supply. The common-mode capability permits direct sensing near ground, which is useful when signals originate from sensors referenced to the same ground as the amplifier. The 700 kHz gain-bandwidth product supports general-purpose gain and signal-conditioning stages without requiring a high-speed amplifier architecture. The architecture is optimized for stable operation in non-inverting and inverting amplifier configurations. Internal frequency compensation removes the need for an external compensation network in ordinary closed-loop designs. Because the two amplifiers are independent rather than electrically linked, each channel can use a different feedback network and input signal. This flexibility makes the dual package suitable for paired sensor channels, control-loop elements, buffer stages, and signal-conditioning blocks. Typical automotive and industrial applications include body and comfort controls, actuator and sensor interfaces, motor-control support circuits, power-supply monitoring, and low-frequency analog signal conditioning. Split-supply operation is useful in circuits centered around ground, while single-supply operation simplifies systems whose signal range begins at 0 V. The TSSOP package also supports compact board layouts where two amplifier channels are required. Design the circuit around the common-mode and output-voltage limits of the selected amplifier configuration. Check that both input signals remain inside the common-mode range, including ground, and that the feedback network does not request an output beyond the selected supply range. Place the feedback components close to the device pins, maintain short input paths, and provide adequate return-current paths to reduce coupling from switching circuitry. This page combines manufacturer product information, automotive qualification details, package information, and application-oriented engineering guidance. It also highlights same-footprint family alternatives and the distinctions that matter when evaluating an automotive dual operational amplifier for a new control or sensor-conditioning design.
LM2904VQPWRQ1 - 26V Dual 700kHz Op Amp | Texas Instruments
The Texas Instruments LM2904VQPWRQ1 is an automotive-grade, dual general-purpose operational amplifier rated for operation from a 3 V to 32 V supply, with a 700 kHz gain-bandwidth product, supplied in an 8-pin TSSOP package. The device provides two independent amplifiers, automotive qualification under AEC-Q100, and operation over a -40°C to +125°C ambient-temperature range. An operational amplifier is a high-gain, high-impedance analog signal-processing component that compares its differential input voltage with a feedback network to produce an amplified output. The dual-amplifier configuration places two amplifiers in one package, reducing board area in applications such as sensor conditioning, current-loop signal processing, filtering, and general-purpose analog amplification. LM2904-Q1 belongs to the operational-amplifier, amplifier IC, and analog IC hierarchy within semiconductor signal-conditioning electronics. The LM2904VQPWRQ1's key attributes are its dual-circuit architecture, 26 V maximum total supply rating, 700 kHz gain-bandwidth product, and ability to operate across a 3 V to 32 V supply range. AEC-Q100 qualification supports its use in automotive electronic systems, while the extended -40°C to +125°C ambient-temperature range addresses industrial temperature requirements. Low supply current and ESD protection are additional features identified in the family datasheet. The amplifier family is designed for general-purpose operation rather than high-speed precision signal paths. Its 700 kHz bandwidth is suitable for moderate-frequency conditioning, while the automotive qualification and wide supply operating range suit electronic control units, sensor interfaces, actuator drivers, battery-powered systems, and industrial measurement modules. Users should confirm output-swing, input-common-mode, offset, and stability limits against the specific operating conditions in the manufacturer datasheet before finalizing a design. Typical applications include low-side current sensing in automotive electronic control units, conditioning resistive sensor signals, amplifying sensor and transducer outputs, active filtering, and general voltage amplification. The two amplifier sections can process related signal paths while sharing one supply package, which simplifies power distribution and reduces component count compared with two discrete single amplifiers. PCB design should provide a stable ground reference, short feedback paths, appropriate input-biasing, and decoupling close to the supply pins. Because automotive environments can contain electrical transients and ESD events, system-level protection and validation remain essential even though the amplifier family includes ESD-protection features. Confirm pin orientation and signal names against the manufacturer pin-configuration table before layout release. This page organizes the automotive dual operational amplifier's electrical limits, package information, design considerations, application guidance, and verified drop-in alternatives. It also distinguishes exact ordering variants by their documented package and qualification differences, helping engineers identify a replacement that fits the same TSSOP footprint before conducting board-level and system validation.
LM2904WHD - Low-Power Dual Op Amp | STMicroelectronics
STMicroelectronics LM2904WHD is a low-power dual operational amplifier with two independent, internally frequency-compensated amplifier circuits in an 8-pin SOIC package. The device is intended for general-purpose signal conditioning and control applications where two amplifier channels, low supply consumption, and operation from a single positive supply are important. The manufacturer datasheet identifies the LM2904 family as suitable for automotive and industrial control systems. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. In voltage-following operation, the circuit presents high input impedance and low output impedance, making it useful for buffers, sensor interfaces, and active filtering. The LM2904 belongs to the broader operational-amplifier hierarchy, which includes general-purpose amplifiers, precision amplifiers, instrumentation amplifiers, and comparators. The LM2904WHD provides two amplifier channels in one package, reducing component count and board area compared with two separate single amplifiers. Its internally frequency-compensated design simplifies closed-loop use in non-inverting, inverting, summing, and feedback configurations. The device is specified as a low-power dual operational amplifier and operates from a single positive power supply, allowing it to interface with low-voltage sensors and control circuitry without a negative supply rail. The 8-SOIC package provides a standard surface-mount footprint suitable for conventional PCB assembly. Because both amplifiers share the same IC, careful layout should keep sensitive input and feedback paths short, maintain stable ground references, and separate the device from high-current switching stages where practical. Stable operation also depends on following the manufacturer recommendations for bypass capacitance, load conditions, output swing, and input common-mode range. Typical uses include industrial sensor conditioning, automotive control modules, battery-powered instrumentation, current-loop interfaces, active filters, and general signal amplification. The dual-channel configuration is particularly useful when a board needs one channel for amplification and the other for buffering, offset correction, or active filtering. The low-power nature of the family also makes it suitable for systems where continuous amplifier quiescent current affects thermal design or battery life. For PCB implementation, place the supply bypass capacitor close to the power pin and connect the decoupling return directly to the appropriate ground plane. Check the datasheet limits for input common-mode voltage, output current, supply voltage, and input offset before fixing the operating point. Avoid relying on output saturation as a substitute for proper supply design, and verify the closed-loop gain-bandwidth and stability margin for the intended feedback network. This product page combines the LM2904WHD device description, verified manufacturer and distributor references, package-level design guidance, application analysis, and clearly qualified replacement information. It is intended to accelerate component identification while preserving the need to validate electrical compatibility in the final system.
LM2904WHDT - Dual Low-Power Op Amp, 8-SOIC | STMicroelectronics
STMicroelectronics LM2904WHDT is a dual, low-power general-purpose operational amplifier packaged in an 8-pin SOIC. It provides 2 independent, internally frequency-compensated amplifier channels with single-ended outputs, making it suitable for signal-conditioning, buffering, and feedback-control circuits. The device is specified for automotive and industrial control systems and is supplied in the tape-and-reel LM2904WHDT configuration. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. The LM2904 belongs to the operational-amplifier hierarchy, which sits within analog and mixed-signal semiconductors. Its dual-channel configuration reduces component count and board area when two amplifier functions are required on the same PCB. Key features include 2 amplifier channels in one package, internal frequency compensation, and low-power operation from a single supply. The internal compensation removes the need for an external dominant-pole capacitor in conventional closed-loop applications. Single-ended outputs also simplify connection to analog-to-digital converters, sensors, transducers, and controller inputs that require a grounded-reference signal. The architecture is suited to low-frequency precision-control applications because each channel has independent signal inputs. Designers can configure each amplifier as a voltage follower, non-inverting amplifier, or inverting amplifier. Unity-gain stability is especially useful for direct sensing and impedance-buffering positions where adding feedback components would be undesirable. Typical uses include automotive sensor interfaces, industrial transducers, motor-control feedback networks, audio preamplifier stages, and low-frequency active filters. The STMicroelectronics product description identifies automotive and industrial control systems as primary application areas, while the low-power architecture benefits portable or distributed equipment operating from a single supply. When assigning PCB tracks, use the manufacturer pin-description table and preserve the standard SOIC-8 pin sequence. Place each bypass capacitor close to the supply pins, route the inverting feedback path away from high-current switching nodes, and confirm output swing, input common-mode range, stability, and output-current requirements against the application before production release. This page combines device identification, package and pin information, drop-in replacement analysis, application-focused guidance, and practical PCB design notes to support component selection, schematic review, sourcing, and second-source qualification.
LM2904WHYDT - Dual General-Purpose Op Amp | STMicroelectronics
STMicroelectronics LM2904WHYDT is a dual general-purpose operational amplifier in an 8-pin SOIC package. The device contains two independent, high-gain, internally frequency-compensated amplifiers, enabling one package to provide two signal-conditioning channels. According to the manufacturer product information, it is intended for automotive and industrial control systems and can operate from a single supply or split supply over a wide voltage range. The low-power architecture makes it suitable for battery-operated equipment, instrumentation, sensor interfaces, and general analog control circuits. An operational amplifier is an analog integrated circuit that amplifies the difference between its inverting and non-inverting inputs. The op-amp category sits within analog signal-chain ICs and serves as a fundamental building block for sensors, filters, buffers, comparators, and closed-loop control systems. The LM2904 family combines internal frequency compensation with two amplifiers in one package, reducing board area compared with separate single-channel devices while preserving independent channels. The LM2904WHYDT is identified as a standard general-purpose amplifier with two single-ended circuits. Its internally compensated architecture allows operation without an external compensation network in many conventional closed-loop configurations. The device is intended for low-power applications and is particularly useful where a compact, general-purpose dual amplifier is preferable to a high-speed precision amplifier. The exact input offset, bandwidth, output-current, and temperature limits should be confirmed from the manufacturer datasheet before final circuit sign-off. Two independent channels can implement voltage followers, transimpedance stages, differential amplifiers, active filters, comparators, and motor or actuator-control loops. A common application is conditioning the output of a bridge sensor, potentiometer, or resistive divider before an ADC samples the signal. In automotive systems, the dual format can economize PCB space in body, climate, or powertrain-control modules where multiple low-power analog channels are required. The SOIC-8 package supports conventional surface-mount assembly and is suitable for lead-free production boards. Place each power pin close to a low-impedance decoupling network and route sensitive input traces away from switching nodes. Because the amplifiers are independent rather than sharing internal signal paths, grounding and supply layout should be designed to minimize channel-to-channel coupling. Verify the exposed operating limits and decoupling recommendations in the manufacturer datasheet for the exact automotive temperature grade. This page combines the manufacturer listing, distributor package identification, sourcing information, pin-compatible alternatives, and practical analog-design guidance. Use the Request a Quote form for current availability, lead time, and commercial terms, and use the official datasheet for authoritative electrical limits before layout release.
LM2904WHYST - Dual 1.1MHz Op Amp | STMicroelectronics
The STMicroelectronics LM2904WHYST is a dual general-purpose operational amplifier with two independent high-gain amplifiers, 1.1 MHz gain-bandwidth product, 0.6 V/us slew rate, and low input bias current of 200 nA per channel. The device is packaged in an 8-pin MiniSO package measuring 3.90 mm in body width. Its electrical characteristics support single-supply and dual-supply operation in industrial control, sensor signal conditioning, and general analog signal-processing systems. An operational amplifier is an analog amplifier that uses very high open-loop gain to compare or amplify a differential input signal. The LM2904 family belongs to the broader operational-amplifier hierarchy, which includes instrumentation, comparator, and rail-to-rail amplifier categories. The LM2904WHYST is intended for applications requiring two amplifiers, moderate bandwidth, low input bias current, and a compact surface-mount footprint rather than precision or high-speed performance. Key features include two amplifier channels, a 1.1 MHz gain-bandwidth product, a 0.6 V/us slew rate, approximately 200 nA input bias current, and 7 mV input offset voltage as identified for this device. The MiniSO-8 package reduces board area while retaining separate power, ground, input, and output connections for each channel. The automotive-oriented ordering code also supports use in temperature-qualified equipment, subject to the device's stated operating limits. Each channel operates as a general-purpose voltage-feedback amplifier, allowing implementation as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style circuit, or active filter. The two independent channels can process separate signals or be combined for differential, instrumentation, and gain-stage arrangements. The 1.1 MHz bandwidth is suitable for low-to-moderate frequency industrial signals, while the 0.6 V/us slew rate supports accurate reproduction of relatively slow input waveforms. Typical applications include low-side current sensing, industrial sensor interfaces, transducer amplification, audio preamplification, and general control loops. In each case, the low input bias current helps reduce source-loading errors, while the dual configuration can reduce the number of separate amplifier packages required on a board. The amplifier is best suited to signals where moderate bandwidth and common-mode performance are more important than rail-to-rail operation or very low offset. Designers should verify the input common-mode range, output swing, supply voltage, and stability requirements against the operating conditions before finalizing the circuit. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a valid common-mode voltage. Feedback-network values and source capacitance should be selected to maintain stable closed-loop operation across the intended gain and load range. This product record combines package, electrical, qualification, sourcing, and drop-in comparison information with practical circuit guidance. It is intended to accelerate engineering selection for compact dual-op-amp designs while clearly distinguishing direct replacements from alternatives that require compatibility review.
LM2904WPT - Dual Low-Power Op Amp | STMicroelectronics
The STMicroelectronics LM2904WPT is a dual, general-purpose operational amplifier in an 8-TSSOP package. The device contains two independent, high-gain operational amplifiers with internal frequency compensation and is designed for automotive and industrial control systems. According to the manufacturer datasheet description, the LM2904W and LM2904AW circuits operate from a single power supply over a wide range of voltages, while the low power-supply drain remains independent of the magnitude of the supply voltage. The LM2904 family belongs to the operational amplifier hierarchy: dual operational amplifier -> general-purpose amplifier -> analog signal-conditioning IC -> semiconductor. Its internally compensated architecture simplifies implementation because an external compensation capacitor is not required for closed-loop operation in typical voltage-follower and inverting-amplifier configurations. The two independent amplifiers can also be used in separate signal chains within the same circuit. The LM2904WPT is identified in the product listings as a 2-circuit, single-ended amplifier in an 8-TSSOP package. The related LM2904AW variant is also documented for automotive and industrial applications. Low power-supply drain, wide single-supply operation, and internal frequency compensation make this family suitable for sensor conditioning, control-loop amplification, audio and instrumentation interfaces, and general industrial electronics. Because the LM2904WPT is a general-purpose amplifier, application performance depends on the selected gain, feedback network, supply voltage, load, and operating temperature. The datasheet should be consulted for the exact input common-mode range, output swing, input bias current, input offset voltage, supply-current limits, and thermal limits before final circuit sign-off. For PCB implementation, route the two amplifier sections with short feedback paths, keep input and output nodes away from switching nodes, and place supply-bypass capacitors close to the device pins. A common ground reference and adequate copper area help preserve signal integrity in low-level analog circuits. This page summarizes the verified device identity, package, application positioning, drop-in sourcing options, and practical design considerations that are useful when evaluating the LM2904WPT for a new analog design.
LM2904WYDT - Low-Power Dual Op Amp, 3-30V | STMicroelectronics
STMicroelectronics LM2904WYDT is a low-power dual operational amplifier with two independent amplifiers, a 3 V to 30 V supply range, and a gain-bandwidth product of 1.1 MHz. The device is supplied in an 8-SOIC package configured for industrial temperature-grade operation. An operational amplifier is an analog signal-processing IC that uses high-gain differential amplification to compare or condition voltages. The LM2904 belongs to the dual general-purpose operational-amplifier category, combining two amplifier channels in one compact package. Its wide supply range makes it suitable for systems powered from industrial 24 V rails, split analog supplies, or lower-voltage circuits when the operating limits are respected. Key characteristics include two amplifier circuits with single-ended outputs, a 1.1 MHz gain-bandwidth product, operation across a 3 V to 30 V supply range, and a common 100 dB figure cited for the family. These characteristics support general-purpose signal conditioning, low-frequency amplification, feedback-based control, and analog sensor interfaces where a precision rail-to-rail amplifier is unnecessary. The LM2904 architecture is designed for dependable operation from conventional dual supplies, including positive and negative rails. Designers should verify input and output voltage limits, common-mode range, output-current capability, and stability requirements against the manufacturer datasheet for the selected operating condition. The two channels share a supply but otherwise operate independently. Typical uses include industrial sensor conditioning, audio preamplification, motor and actuator interfaces, current-loop signal processing, sample-and-hold circuits, and general DC signal amplification. The 1.1 MHz bandwidth is appropriate for low-frequency control and analog conditioning rather than high-speed video or RF signal chains. Decoupling remains important in precision analog systems. Place a suitable bypass capacitor close to each supply pin and keep feedback components and sensitive input traces away from switching nodes. Account for input bias current, input offset voltage, output swing, and load-capacitance stability when selecting external components. This product overview consolidates the exact LM2904WYDT package, electrical characteristics, sourcing terms, comparison parameters, and practical design guidance. It also identifies same-footprint family alternatives so engineers can assess temperature-grade, revision, and sourcing differences before approving a replacement.
LM2904WYPT - Dual 1.1MHz Op Amp, 100dB, 8-TSSOP | ST
The STMicroelectronics LM2904WYPT is a low-power dual operational amplifier with two independent, internally frequency-compensated amplifiers in an 8-pin TSSOP package. It provides approximately 1.1 MHz unity-gain bandwidth and 100 dB typical open-loop gain, making it suitable for general-purpose signal conditioning in automotive and industrial control systems. The device operates from a single power supply over a wide input-voltage range. An operational amplifier is an analog amplifier that uses very high open-loop gain and negative feedback to amplify a differential input signal. Within the broader semiconductor hierarchy, the LM2904WYPT is an amplifier IC, a general-purpose operational amplifier, and a dual-amplifier device. Its two independent channels make it economical for designs that require two amplifier functions in one compact surface-mount package. Internal frequency compensation means no external compensation network is required for ordinary closed-loop operation. This simplifies implementation in sensor interfaces, buffer stages, active filters, comparators, and control loops. The dual configuration also allows the two amplifiers to handle separate signals or to be cascaded when higher closed-loop gain is required. The LM2904 family targets automotive and industrial control systems where a single-supply amplifier, low power consumption, and stable operation across supply-voltage variations are important. Its wide common-mode and output-voltage ranges support sensors and control circuitry powered from a single rail, while the two independent channels keep the component count and board area below that of two separate single-amplifier packages. A key design consideration is the input-bias-current error produced by the differential input stage. In high-impedance sensor applications, resistor values must be selected so that bias-current-induced offset remains small compared with the sensed signal. Resistor thermal noise and the amplifier's own noise should also be checked together when working with low-amplitude analog signals. This page combines manufacturer-family characteristics, package information, pricing evidence, and application-oriented design guidance. It also identifies which same-package alternatives can be considered without requiring PCB changes, helping engineers compare sourcing options before releasing a production design.
LM2904YDT - 30V Low-Power Dual Op Amp | STMicroelectronics
The STMicroelectronics LM2904YDT is a low-power dual operational amplifier with two independent amplifiers, a 30 V family voltage rating, a 0.6 V/µs slew rate, and an 8-pin SOIC package. It is intended for general-purpose signal-conditioning applications where two amplifier channels, low power consumption, and a tolerant supply-voltage range provide a practical combination of capability and board economy. An operational amplifier, or op amp, is a voltage-gain device used to amplify small input signals in analog signal chains. The LM2904 family belongs to the broader hierarchy of analog integrated circuits, signal amplifiers, operational amplifiers, and general-purpose amplifiers. Its differential inputs and single-ended outputs allow each channel to support common tasks such as buffering, gain amplification, voltage comparison, filtering, and instrumentation-style signal conditioning. The LM2904YDT provides two amplifier circuits in one 8-SOIC package. Its stated 30 V family rating supports operation from single-supply industrial signal-conditioning circuits, while the low-power architecture suits battery-powered and portable equipment. The 0.6 V/µs slew rate provides a concrete indication of how quickly the output can follow a changing input, making the device appropriate for low-to-moderate-bandwidth applications rather than high-speed signal paths. STMicroelectronics describes the LM2904 family as a low-power dual operational amplifier. The automotive-oriented Y suffix and automotive-grade classification make the LM2904YDT relevant to vehicle electronics, industrial controls, and other systems that require a dual amplifier in a compact surface-mount package. Because the package contains two channels, PCB area and component count can be reduced compared with separate single-channel amplifiers. Typical uses include low-frequency sensor conditioning, current-loop signal amplification, audio preamplification, active filtering, voltage buffering, and general industrial control. The device is also suitable for split-supply circuits when the signal can remain within the input and output common-mode limits specified by the manufacturer datasheet. Applications requiring wide bandwidth, rail-to-rail input or output operation, very low offset voltage, or low-noise performance should compare the LM2904YDT with precision or rail-to-rail amplifier families before finalizing the design. Designers should verify input common-mode range, output swing, output-current capability, and stability with the external compensation network for each specific operating point. Keep input and feedback traces short, place decoupling capacitors close to the supply pins, and avoid using the amplifier outside its stated supply and common-mode limits. A bypass capacitor near each device helps control supply-line noise on shared analog boards. This product page combines the LM2904YDT operating identity with package, application, drop-in replacement, and design guidance. It highlights where the conventional low-power dual op amp is appropriate and where precision, speed, or rail-to-rail characteristics may justify a different amplifier architecture.