Amplifier ICs
بەرهەمەکان (3,200+)
LM339MX - Quad Open-Collector Comparator | Texas Instruments
The Texas Instruments LM339MX is a general-purpose quad voltage comparator containing four independent comparator channels in a 14-pin SOIC package. Each channel supports single or dual power-supply operation across a total range of approximately 36 V, or approximately ±18 V, and uses an open-collector output. Verified distributor data identifies a response time of 1.3 µs, output compatibility with TTL, CMOS, MOS, DTL, and ECL logic, and an operating temperature range of 0 °C to 70 °C. A voltage comparator is an analog signal-conditioning integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The comparator category belongs to the wider hierarchy of analog IC, signal-conditioning IC, logic-interface IC, and semiconductor. The LM339MX is therefore positioned between precision analog conversion and digital logic systems, converting a small voltage difference into a logic-level transition that can drive digital control, protection, or monitoring circuitry. The four independent channels make the LM339MX suitable for multi-threshold monitoring without requiring four separate packages. Its open-collector outputs permit wired-AND behavior when multiple channels or external devices pull the same output node low. Each channel also supports a pull-up arrangement rather than driving the output rail directly, allowing interface compatibility with different logic families. The approximately 1.3 µs response time makes the device suitable for general-purpose control loops rather than high-speed edge-detection applications. The 14-pin SOIC footprint supports compact through-hole-style PCB assembly and is pin-compatible with common LM339-family and general-purpose quad-comparator implementations. Because the outputs are open collector, a pull-up resistor is normally required when driving CMOS or TTL inputs. The four channels share supply and ground pins, so decoupling should be placed close to the package power pins and the ground return should follow a low-impedance path. Typical uses include overvoltage and undervoltage monitoring, power-supply sequencing, battery threshold detection, window comparators, motor-control interfaces, and industrial control systems. Compared with faster rail-to-rail comparators, the LM339MX emphasizes wide supply operation, multiple logic-output compatibility, and a straightforward open-collector interface rather than low-power or nanopower operation. For new designs, verify the exact input common-mode range, output-current limits, and switching behavior against the selected manufacturer datasheet because these values were not included in the retrieved source snippets. This page combines verified distributor specifications, package details, drop-in alternatives, and application guidance to support engineering selection.
LM339MX/NOPB - 4-Comparator, 1.3 us | Texas Instruments
Texas Instruments LM339MX/NOPB is a four-channel, general-purpose voltage comparator with open-collector outputs, a 1.3 us response time, and a 14-pin SOIC package. Each channel provides independent comparison functions, while the device supports single-supply or dual-supply operation across a 2 V to 36 V total supply range. The open-collector outputs are compatible with CMOS, MOS, TTL, DTL, and ECL logic, allowing wired-AND operation and flexible pull-up implementation. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. The LM339 belongs to the comparator hierarchy, where a comparator IC converts an analog decision into a logic-level output. It is used when a system needs threshold detection, overvoltage protection, window comparison, sensor conditioning, or a simple control decision without requiring the gain and feedback behavior of an operational amplifier. The four internal comparators offer input offset voltage as low as 2 mV maximum for all four channels, a 1.3 us response time, and typical supply current of 800 uA. Open-collector outputs require an external pull-up resistor when driving a logic input. This architecture can provide level translation, wired-AND bus behavior, and collective open-drain signaling, although pull-up selection, output rise time, and bus capacitance must be considered during design. According to the Texas Instruments LM339 product information, the B version is a drop-in replacement for LM239, LM339, and LM2901, while the A and V versions have different characteristics. The device family supports a common-mode input voltage range that includes ground and a differential input range equal to the maximum-rated supply voltage. Output compatibility with TTL, MOS, and CMOS makes the comparator suitable for mixed-voltage systems, although logic thresholds and supply conditions should be checked against the selected interface. Typical uses include DC overvoltage and undervoltage detection, battery monitoring, sensor threshold switching, temperature-control loops, window comparators, and industrial control interfaces. The 14-pin SOIC package supports surface-mount assembly and provides separate input, output, and ground connections for each comparator. The open-collector architecture is particularly useful when several detectors must share a wired signal or when the output must interface with a logic voltage different from the comparator supply. Design with adequate input common-mode range, correct supply polarity, and an appropriate pull-up network. Do not permit comparator inputs to exceed the device rating, and account for output saturation, pull-up resistance, bus loading, and propagation delay in timing-sensitive control paths. The 0 °C to 70 °C temperature range identifies this ordering code for commercial-temperature operation. This product page combines the manufacturer specifications, package and pin information, sourcing guidance, drop-in replacement analysis, comparison parameters, and practical interface guidance. It is designed to help engineers determine whether the LM339MX/NOPB fits a new design or can replace an existing four-channel comparator without changing the PCB footprint.
LM339N - Quad Open-Collector Comparator | Texas Instruments
The Texas Instruments LM339N is a low-power, low-offset quad differential comparator containing four independent comparator channels in a 14-pin PDIP package. The verified source identifies the device as a general-purpose comparator with open-collector outputs, a 2 V to 36 V supply range, and approximately 1.3 microsecond response time. Each channel can compare two input voltages, while its open-collector output requires an external pull-up resistor for a usable logic-high level. A quad comparator is an analog comparator integrated circuit used to determine whether an input voltage is higher or lower than a reference voltage. The comparator function belongs to the broader analog and mixed-signal semiconductor hierarchy: comparator -> differential comparator -> analog IC -> semiconductor. LM339N provides four channels in one package, reducing component count when a system needs several independent threshold, sorting, overvoltage, or sensing decisions. The main verified characteristics are four independent comparator sections, open-collector outputs, a 14-pin PDIP package, and a wide operating supply range of 2 V to 36 V. The manufacturer describes the LM339-N family as a low-power, low-offset voltage quad comparator. Because the outputs are open collector, the output stage can sink current but does not actively drive a high voltage; an external resistor connects the output node to the desired positive supply. This arrangement supports wired logic, relay or lamp drive, and level translation when the pull-up voltage is selected appropriately. The open-collector architecture also provides a useful benefit in multi-comparator systems: several outputs can be connected to a common pull-up node when the application intentionally requires wired-AND behavior. The design must account for the voltage and current limits of every connected output and for the sink-current capability of each comparator. The external pull-up resistor also affects rise time, so a lower resistance can improve speed while increasing current and power dissipation. Typical uses include DC threshold detection, battery and supply monitoring, window comparison, industrial control logic, sensor conditioning, overvoltage indication, and general-purpose analog decision circuits. The four channels can be used for independent comparisons or arranged as a multi-level voltage detector. Because input and output details beyond the verified source were not supplied, exact input common-mode limits, output sink-current limits, input offset, response-time conditions, and temperature ranges should be confirmed in the manufacturer datasheet before production release. The LM339N is primarily a through-hole general-purpose comparator rather than a high-speed logic device. Its strength is simple wide-supply operation with four channels and open-collector outputs. A PCB design should route comparator inputs away from switching nodes, provide a stable reference, use a defined ground return, and choose pull-up resistors according to the required logic voltage, rise time, and current budget. This page combines verified distributor and manufacturer information with application-oriented design guidance while avoiding unsupported numeric claims.
LM339N/PB - Quad Open-Collector Comparator | Texas Instruments (Lead-Free (Pb-Free))
The Texas Instruments LM339N/PB is a low-power, low-offset quad differential comparator containing four independent comparator channels in a 14-pin PDIP package. The verified source identifies the device as a general-purpose comparator with open-collector outputs, a 2 V to 36 V supply range, and approximately 1.3 microsecond response time. Each channel can compare two input voltages, while its open-collector output requires an external pull-up resistor for a usable logic-high level. A quad comparator is an analog comparator integrated circuit used to determine whether an input voltage is higher or lower than a reference voltage. The comparator function belongs to the broader analog and mixed-signal semiconductor hierarchy: comparator -> differential comparator -> analog IC -> semiconductor. LM339N/PB provides four channels in one package, reducing component count when a system needs several independent threshold, sorting, overvoltage, or sensing decisions. The main verified characteristics are four independent comparator sections, open-collector outputs, a 14-pin PDIP package, and a wide operating supply range of 2 V to 36 V. The manufacturer describes the LM339-N family as a low-power, low-offset voltage quad comparator. Because the outputs are open collector, the output stage can sink current but does not actively drive a high voltage; an external resistor connects the output node to the desired positive supply. This arrangement supports wired logic, relay or lamp drive, and level translation when the pull-up voltage is selected appropriately. The open-collector architecture also provides a useful benefit in multi-comparator systems: several outputs can be connected to a common pull-up node when the application intentionally requires wired-AND behavior. The design must account for the voltage and current limits of every connected output and for the sink-current capability of each comparator. The external pull-up resistor also affects rise time, so a lower resistance can improve speed while increasing current and power dissipation. Typical uses include DC threshold detection, battery and supply monitoring, window comparison, industrial control logic, sensor conditioning, overvoltage indication, and general-purpose analog decision circuits. The four channels can be used for independent comparisons or arranged as a multi-level voltage detector. Because input and output details beyond the verified source were not supplied, exact input common-mode limits, output sink-current limits, input offset, response-time conditions, and temperature ranges should be confirmed in the manufacturer datasheet before production release. The LM339N/PB is primarily a through-hole general-purpose comparator rather than a high-speed logic device. Its strength is simple wide-supply operation with four channels and open-collector outputs. A PCB design should route comparator inputs away from switching nodes, provide a stable reference, use a defined ground return, and choose pull-up resistors according to the required logic voltage, rise time, and current budget. This page combines verified distributor and manufacturer information with application-oriented design guidance while avoiding unsupported numeric claims.
LM339NE3 - 36V Quad Open-Collector Comparator | Texas Instruments
The Texas Instruments LM339NE3 is a four-element differential comparator IC with a 2 V to 36 V single-supply operating range, open-collector outputs, and a 14-pin PDIP package. Each comparator provides low input offset voltage of 0.37 mV, input bias current of 3.5 nA, supply current of 200 µA per comparator, and response time of 1 µs. These characteristics make the LM339NE3 suitable for general-purpose threshold detection and analog signal comparison. A comparator is an analog interface IC that compares two input voltages and produces a logic-level indication of their relationship. The LM339 belongs to the broader comparator hierarchy and operates as a general-purpose signal-conditioning component between sensor, reference, and digital-control stages. Its common-mode input range includes ground, allowing the device to monitor signals referenced to a negative rail in dual-supply systems. Four independent comparators are integrated into one package, reducing component count on boards that require multiple threshold or window-detection functions. The open-collector output architecture can sink logic-level current while normally leaving the output transistor off, which supports wired-AND behavior when several outputs share a pull-up resistor. The output stage is compatible with TTL, MOS, and CMOS logic according to the manufacturer product information. The low 200 µA supply current per comparator supports low-power monitoring systems, while the 1 µs response time provides useful speed for supply sequencing, overvoltage detection, and fast control loops. Input offset voltage determines how close the two inputs must be before the output changes state, while input bias current affects the impedance presented to the sensing circuit. The common-mode range and differential input limits must both be checked in high-voltage systems. Typical uses include battery monitoring, power-supply sequencing, overvoltage and undervoltage detection, window comparators, sensor thresholding, relay-control logic, and industrial control systems. The open-collector outputs are particularly useful when multiple detector channels must indicate one combined fault condition. A suitable pull-up resistor is required for normal digital-logic operation because the outputs do not actively drive a high voltage. For reliable PCB design, keep input traces away from switching-power nodes, place the pull-up resistor close to the open-collector output, and decouple the supply connection locally. Designers should verify input and output limits under worst-case supply, temperature, and common-mode conditions. The DIP package is suitable for through-hole assembly, prototyping, and applications that favor easy inspection or manual replacement. This product page combines the manufacturer electrical characteristics, package information, application guidance, drop-in alternatives, and practical design notes to support component selection, PCB implementation, and lifecycle-aware purchasing decisions.
LM339NE4 - Quad 36V Comparator | Texas Instruments | DIP
Texas Instruments LM339NE4 is a quad differential analog comparator with four independent comparison channels, 300 ns nominal response time, and operation from 2 V to 36 V in a 14-pin PDIP package. Its open-collector outputs are compatible with TTL, MOS, and CMOS logic, making the device suitable for general-purpose threshold detection and control systems. An analog comparator is a semiconductor that compares two input voltages and changes its output state when the difference crosses a selected threshold. The LM339 belongs to the comparator hierarchy, where a general-purpose comparator can be used for voltage monitoring, sensing, level translation, and open-loop control. Placing four comparison functions in one integrated circuit reduces component count and simplifies design in equipment with several independent analog thresholds. The LM339NE4 offers low input offset voltage of 0.37 mV, low input bias current of 3.5 nA, and low supply current of 200 µA per comparator. According to the Texas Instruments datasheet, the device supports input and output logic interfacing with TTL, MOS, and CMOS systems. These characteristics are important when the comparator must detect small input-voltage changes without introducing excessive bias or loading on the signal source. The open-collector architecture provides flexibility in output pull-up selection and permits wired logic connections when suitable pull-up resistors are installed. However, the output must not be left without an appropriate pull-up because the open-collector transistor remains off when it is not actively sinking current. Rise time therefore depends on the pull-up resistance, total bus capacitance, and the number of attached loads. Typical uses include industrial control and monitoring, overvoltage and undervoltage detection, sensor-interface thresholds, battery monitoring, panel and instrument threshold circuits, and general digital control. The four channels may monitor several rails or signals independently, while common power and ground connections simplify the implementation of multi-channel systems. Designers should verify the differential input range, common-mode input range, supply voltage, output pull-up network, and channel-to-channel behavior against the manufacturer datasheet. The broad voltage capability is useful for industrial systems, but the comparator must still be checked for the exact input conditions and output timing required by the application. This page consolidates electrical characteristics, sourcing guidance, drop-in replacement options, pin information, comparison parameters, and practical PCB design notes into one engineering-focused reference for evaluating the LM339NE4.
LM339NG - 3-36V Quad Open-Collector Comparator | onsemi
The onsemi LM339NG is a four-channel general-purpose analog comparator with a 3 V to 36 V single-supply operating range, open-collector CMOS/TTL-compatible outputs, and a 14-pin PDIP package. Each channel compares two input voltages, making the device suitable for level detection, low-level sensing, memory applications, threshold control, and industrial interface circuits. The LM339NG supports single or split supply operation. An analog comparator is an integrated circuit that determines whether an input voltage is above or below a reference voltage. In the broader electronics hierarchy, a comparator belongs to the analog IC and signal-conditioning category, where it converts a continuously varying voltage relationship into a logic-level decision. Unlike an operational amplifier, a comparator is optimized for fast switching between output states rather than linear amplification. The four independent LM339NG channels combine a wide supply-voltage range with low input bias current. Verified sources report a typical input bias current of 25 nA, a typical input offset current of ±5 nA, and an input offset voltage of 1.3 mV. The distributor descriptions identify the outputs as open collector, allowing the output stage to sink current rather than actively sourcing it. This architecture requires an external pull-up resistor when the comparator must produce a valid high level. With a response time of approximately 1.3 microseconds, the LM339NG is suitable for general-purpose detection rather than very high-speed signal comparison. Its 14-pin PDIP construction supports through-hole assembly and is useful in industrial control equipment, automotive electronic modules, consumer appliances, memory-control circuits, and laboratory interface boards. The package is also readily inspected or replaced during maintenance. A key design consideration is the open-collector output. Each output requires a pull-up resistor to the appropriate logic supply, and the pull-up voltage must not exceed the applicable device limits. Input common-mode range, output saturation, input protection, and supply-current behavior should be checked against the manufacturer datasheet before operation near the supply extremes. This page consolidates verified distributor information, source-linked specifications, practical application guidance, and cautious drop-in alternatives. It also distinguishes confirmed LM339NG characteristics from attributes that still require full datasheet or application-specific verification before production use.
LM339NSRG4 - Quad Open-Collector Comparator | Texas Instruments
Texas Instruments LM339NSRG4 is a quad differential voltage comparator containing four independent comparator sections, a maximum offset voltage of 9 mV, and a response time of 1300 ns in a 14-pin SOIC package. It supports single-supply or dual-supply operation and is designed for general-purpose signal comparison applications. Each channel can compare a differential input pair against a common reference, while the open-collector outputs allow wired logic, pull-up resistors, and flexible system-level voltage interfacing. A voltage comparator is an analog interface IC that evaluates two input voltages and changes its output state when the difference between them crosses a defined threshold. The LM339 belongs to the broader comparator and signal-conditioning hierarchy, where its four channels can implement threshold detection, zero-crossing detection, window comparison, saturation sensing, and basic control decisions. Its multi-channel architecture also allows one package to monitor several independent conditions without requiring four separate comparator devices. Key characteristics include operation from a single supply or from dual supplies, a tested supply rating of 30 V for LM339 versions and up to 32 V for non-V devices, low supply-current drain that is independent of supply voltage, and a typical supply-current drain of 0.8 mA. The open-collector output architecture requires an external pull-up, providing flexibility in output voltage and bus-level compatibility. The four channels share supply pins but otherwise retain independent input and output connections. The LM339 architecture is suited to low-cost analog decision circuits because its inputs respond to a wide common-mode range while the open-collector outputs remain electrically flexible. Because bipolar comparators can draw input bias current, source impedance should be limited where offset errors matter. Open-collector outputs can also expose the output node to more than one driver, so wired-AND logic requires careful pull-up selection and a review of output sink-current limits before several comparators share a node. Typical uses include industrial sensor interfaces, overvoltage and undervoltage monitors, temperature-threshold circuits, motor-control interfaces, power-supply supervision, and general industrial control systems. It is particularly useful when several independent comparisons must be performed within a limited board area and a 14-pin surface-mount footprint is preferred over through-hole DIP packaging. When designing around the LM339NSRG4, include a pull-up resistor on every open-collector output, keep input common-mode voltage within the device operating limits, and account for input bias current when using high-impedance sensors. Place bypass capacitance close to the supply pins and route sensitive comparison inputs away from switching nodes and high-current return paths. This page organizes the LM339NSRG4’s key electrical characteristics, application guidance, pin-level information, and carefully qualified replacement options. It is intended to help engineers confirm footprint compatibility, assess threshold accuracy and response time, and plan the external components required by an open-collector comparator design.
LM339PT - 4-Channel Open-Collector Comparator | STMicroelectronics
The STMicroelectronics LM339PT is a low-power quad voltage comparator containing four independent comparison channels in a 14-pin TSSOP package. Each channel supports single-supply or split-supply operation and uses an open-collector output, allowing the outputs to be wired together for wired-AND behavior. The verified product data identifies a 1 V to 16 V supply range, a maximum input offset voltage of 2 mV for the A-grade device family, and compatibility with CMOS, DTL, ECL, MOS, open-collector, and TTL logic. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The LM339 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its four independent channels can perform threshold detection, overvoltage monitoring, window comparison, zero-crossing detection, and general-purpose signal conditioning. Unlike a digital logic gate, the comparator evaluates continuously varying analog voltages at its inputs. The main feature of the LM339PT is its combination of four independent open-collector comparators in one compact TSSOP-14 package. Its low-power design is suitable for battery-powered equipment, while the broad supply-voltage range supports industrial control and instrumentation systems. The open-collector architecture requires an external pull-up resistor and can interface with CMOS or TTL logic. The verified distributor description also reports a propagation delay of 1.3 µs, making the device suitable for moderate-speed threshold and protection functions rather than ultra-high-speed applications. Each comparator channel has two input pins, an output, and access to the device ground and supply pins. The outputs are open-collector rather than push-pull, so an output can sink current while remaining high-impedance when inactive. Pull-up resistors are therefore required on every used output. Connecting outputs together requires compatible pull-up arrangements and careful review of the maximum sink-current and voltage limits. The device does not provide a latch function, so applications requiring state retention normally add external feedback or latch circuitry. Typical uses include DC overvoltage detection, power-supply sequencing, sensor threshold switching, battery monitoring, industrial control interfaces, and logic-level conversion. Split-supply operation allows the comparator to evaluate signals around ground, while single-supply operation is useful when all measured signals remain above the common-mode limits. Because the outputs are open collector, the device can also connect to buses such as SMBus or I2C where wired-AND behavior is required, provided the electrical and timing requirements of the specific bus are satisfied. Designers should account for input common-mode range, output pull-up resistance, supply decoupling, and the behavior of the open-collector output at temperature extremes. Place the device close to the protected signal and provide a stable ground reference. Avoid relying on an output to source current, and select a pull-up voltage compatible with both the comparator output ratings and the driven logic family. The TSSOP-14 package supports compact PCB layouts, but pin-1 orientation must be checked carefully because closely spaced leads can complicate hand rework. This product page consolidates verified distributor availability and pricing, package information, same-package cross-references, and practical design guidance. It also distinguishes drop-in replacements from devices that differ in package or temperature grade, helping engineers make a replacement decision without assuming that every similarly named LM339 variant is electrically and mechanically interchangeable.
LM339PWG4 - Quad Open-Collector Comparator | Texas Instruments
The Texas Instruments LM339PWG4 is a quad differential comparator containing four independent voltage-comparison channels, an open-collector output architecture, and a 14-pin TSSOP package. Each comparator supports single-supply or dual-supply operation, with a maximum supply-voltage rating of 38 V, low input offset voltage of 0.37 mV, low input bias current of 3.5 nA, and typical supply-current consumption of 200 uA per comparator. The LM339 family provides common-mode input operation that includes ground and outputs compatible with TTL, MOS, and CMOS logic. A differential comparator is an analog integrated circuit that compares two input voltages and produces a binary result indicating which input is higher. The LM339 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Four independent channels allow one package to perform several threshold, level, window, or sensing functions. Its open-collector outputs require an external pull-up resistor, allowing the output voltage to be raised to a logic supply selected by the system designer. Key features include four independent comparator channels, a wide 36 V operating supply range indicated by the manufacturer’s related part listing, and a 38 V maximum rating. The device offers a typical total supply-current drain of 0.8 mA, a low input offset of 0.37 mV, and an input bias current of 3.5 nA. Its open-collector architecture is useful for wired-AND buses, relay-driver interfaces, and systems that need a pull-up voltage different from the comparator supply. The LM339 architecture is suited to general-purpose precision comparison rather than high-speed waveform discrimination. The manufacturer identifies LM339B, LM2901B, LM339, LM239, and LM139 as related quad differential comparators and states that the B-version is a drop-in replacement for the earlier A- and V-version families. Open-collector outputs can sink logic current but cannot actively drive a high voltage without a pull-up network. Typical applications include sensor-threshold conditioning, battery and power-supply monitoring, industrial control interfaces, window comparators, LED status signaling, and open-collector alarm or relay-control signaling. The four-channel organization can also reduce package count when a board needs independent comparisons for multiple sensors or rails. In circuits sharing an input source, each channel can compare that source against a different threshold. Designers should treat the output as a sinking device rather than a push-pull logic driver. Place the pull-up resistor close to the relevant output, account for rise time when driving capacitive loads, and use the pin-description table in the Texas Instruments datasheet when assigning PCB tracks. Input common-mode range, output pull-up voltage, and total supply dissipation must be checked against the intended application. This product page combines the manufacturer’s device characteristics with engineering-focused comparisons, application guidance, pin-related cautions, and a strict same-package replacement analysis. It is designed to help engineers determine whether the 14-pin TSSOP LM339PWG4 fits a precision comparator design without assuming that a superficially similar part is electrically or mechanically interchangeable.
LM339PWRG3 - Quad 36V Comparator | Texas Instruments
Texas Instruments LM339PWRG3 is a quad differential comparator integrated circuit containing four independent voltage comparators. It operates from a single supply of up to 36 V or from dual supplies whose total span is 2 V to 36 V, and it is housed in a 14-pin TSSOP package. Each channel supports an open-collector output compatible with TTL, MOS, and CMOS logic. The device is intended for general-purpose threshold detection, signal conditioning, and industrial control applications. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input crosses the other. The LM339 family belongs to the comparator hierarchy within analog ICs and broader semiconductor signal-processing devices. Its four independent channels allow a single package to implement multiple sensing, protection, or level-conversion functions without requiring four separate single-comparator packages. The LM339 family is designed for wide supply-voltage operation and common-mode input ranges that include ground. According to the Texas Instruments product page, the B-version is a drop-in replacement for LM239, LM339, and LM2901 devices, while the differential input range can equal the maximum-rated supply voltage of 38 V. Open-collector outputs allow wired-AND operation and require an external pull-up resistor. The outputs are designed to drive TTL, MOS, and CMOS-compatible logic. The verified specifications identify a maximum input offset of 0.37 mV, an input bias current of 3.5 nA, and a supply current of 200 uA per comparator. A faster response is also listed as a family improvement. These characteristics make the LM339 useful when a system must compare low-level sensor signals against adjustable references while tolerating substantial supply variation. The open-collector architecture is especially useful where multiple channels must share a pull-up or where a wired fault-detection signal is required. Typical uses include industrial control systems, battery-powered monitoring equipment, sensor threshold circuits, window or level comparators, overvoltage detection, and general digital interface conditioning. The wide operating range is valuable in industrial systems, while the low 200 uA per-comparator supply current supports low-power monitoring designs. Each internal comparator is electrically independent, allowing unused channels to be configured according to the manufacturer datasheet. Layout should preserve a low-impedance ground reference and keep input and feedback traces short because comparison accuracy can be affected by input offset, bias current, and parasitic coupling. Open-collector outputs require suitable pull-up resistors and adequate logic-level current margin. Review the manufacturer pin-description table before assigning tracks because input, output, supply, and ground functions are distributed across the 14-pin TSSOP. This page combines the LM339 family specifications with practical interpretation of supply range, input behavior, output compatibility, package construction, application fit, and replacement considerations. It helps engineers compare the device against closely related TI parts while keeping PCB footprint, logic interface, and analog performance requirements in view.
LM339SNG - Quad Single-Supply Comparator, 14-Pin PDIP
onsemi LM339SNG is a quad voltage comparator integrated circuit with four independent comparison channels, a single-supply architecture, and a 14-pin PDIP package. The LM339SNG is identified as a comparator device covering an 18 V to 36 V operating range, making it suitable for industrial control, instrumentation, power-monitoring, sensor-interface, and threshold-detection circuits. Its four-channel arrangement allows one packaged device to implement several independent switching decisions while reducing component count and simplifying PCB layout. A comparator is an analog integrated circuit that evaluates two input voltages and produces a logic-level output indicating which input is higher. In the broader electronics hierarchy, LM339SNG belongs to the comparator family within analog and mixed-signal semiconductors. Its single-supply operation is useful when the system has one main supply rail, while its open-collector-style output class is commonly used to drive pull-ups, relay drivers, alarm inputs, and digital control logic. The LM339SNG provides four comparator channels in one package. The 14-pin PDIP arrangement gives adequate spacing for through-hole assembly, inspection, and prototype rework, although it occupies more board area than surface-mount equivalents. The device is particularly useful when a design requires multiple analog threshold decisions and the board maker prefers a readily available through-hole package. A single IC can reduce the number of separate packages and simplify routing between sensing and control sections. Typical applications include sensing relay and solenoid drivers, overvoltage and undervoltage detection, window comparators, battery monitoring, level detection, industrial control interfaces, and general-purpose logic threshold circuits. Because comparator outputs are intended to indicate the relative state of two analog inputs, designers should pay attention to input common-mode range, output pull-up requirements, propagation delay, input offset, and supply voltage limits when establishing system behavior. These operating details should be confirmed against the manufacturer datasheet before final qualification. For implementation, place the device close to the signals being compared and keep sensitive analog traces away from fast-switching nodes. Use suitable bypass capacitance near the supply pins, provide the required pull-up network for the outputs, and verify that every signal remains within the device's supported common-mode and supply limits. The 14-pin PDIP package is particularly appropriate for through-hole industrial, educational, and control-board assemblies where mechanical robustness is more important than minimum board area. This product page combines the verified LM339SNG identity and package information with practical guidance on comparator behavior, PCB implementation, application fit, and drop-in alternatives. It is intended to help engineers confirm whether the single-supply quad comparator is appropriate for a new design before committing to a board layout or production build.
LM358AD - Dual Low Power Op-Amp, 1.1MHz, SOIC-8 | STMicroelectronics
The STMicroelectronics LM358AD is a low-power dual operational amplifier consisting of two independent, high-gain, internally frequency-compensated op-amps designed to operate from a single power supply across a wide voltage range. Housed in an 8-pin SOIC package, the LM358AD delivers a unity-gain bandwidth of approximately 1.1 MHz, a slew rate of 0.6 V/µs, and supports supply voltages from 3V to 30V single-supply or ±1.5V to ±16V dual-supply. The device is widely used in cost-sensitive analog front-ends where single-supply operation and low quiescent current are essential design constraints. An operational amplifier (op-amp) is a high-gain, DC-coupled electronic voltage amplifier with differential inputs and a single-ended output. Within the broader power management and signal conditioning hierarchy, the LM358AD belongs to the general-purpose op-amp category, sitting between precision instrumentation amplifiers (high accuracy, low noise) and high-speed amplifiers (wide bandwidth, fast slew). Op-amps form the building blocks of analog signal chains: filters, comparators, integrators, transducers, sensor signal conditioners, and active rectifiers. The LM358 family specifically targets single-supply 5V/12V/24V systems that cannot tolerate the negative rail required by legacy op-amps like the LM741. Key features include: 1.1 MHz gain-bandwidth product, 0.6 V/µs slew rate, input common-mode range that includes ground (enabling true single-supply sensing near 0V), low input bias current, internal frequency compensation (no external capacitor required), and ESD protection on the inputs. The output stage can swing to within a few hundred millivolts of the negative rail, although it does not reach the positive rail — meaning the part is not rail-to-rail but is sufficient for most single-supply transducer interfaces. Technically, the LM358AD uses a bipolar junction transistor (BJT) input stage rather than JFET or CMOS, which trades higher input bias current (~45 nA typical) for extremely low input offset voltage drift and predictable behavior across temperature. The two amplifiers share only the power pins; their inputs and outputs are fully independent, allowing asymmetric configurations such as one channel as a comparator and the other as a gain stage. Typical applications include battery-powered sensor signal conditioning, transducer amplifiers, DC gain blocks, active filters, integrators, comparators with hysteresis, and 4–20 mA current loop transmitters. Industrial designs frequently use the LM358AD in 24V PLC analog input modules, while consumer designs use it for white-goods sensor interfaces and IoT battery nodes. When designing with this device, remember that the output cannot swing to the positive rail — typically VOH stops around VCC−1.5V at 10 mA load. Place a 100 nF bypass capacitor close to VCC and ground, and use a feedback resistor of at least 10 kΩ to limit output stage loading. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
LM358ADDR - Dual 30V 700kHz Op Amp | Texas Instruments
The LM358ADDR is a dual operational amplifier from Texas Instruments, part of the industry-standard LM358 family. It operates from a single supply of 3V to 30V or dual supplies of +/-1.5V to +/-15V, with a typical supply current of 500uA per amplifier, packaged in an 8-pin SOIC (D) surface-mount package delivered in tape and reel. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block of analog electronics used in signal conditioning, filtering, and mathematical operations. The LM358 is a dual op amp containing two independent amplifiers in one package, offering design flexibility and space savings. It belongs to the broader category of linear integrated circuits (amplifier ICs) used across power management, sensor interfaces, and audio processing. Key features include a common-mode input voltage range that extends to ground, enabling true single-supply operation with inputs referenced to ground. The gain-bandwidth product is 700kHz with a 0.3V/us slew rate, and maximum input offset voltage is 3mV. The operating temperature range is 0C to 70C for commercial applications. The device is RoHS compliant and lead-free. Technically, the LM358 uses a bipolar process with a class-AB output stage for low output distortion. The PNP input pair enables the input common-mode range to include ground. The output swings close to but not rail-to-rail, a consideration for maximum-swing designs. Internal frequency compensation ensures unity-gain stability without external components. Typical applications include transducer amplifiers, DC gain blocks, active filters, battery chargers, power supply control, and motor control loops. The dual configuration handles multiple signal paths in a compact footprint, reducing board space and component count. When designing with the LM358ADDR, ensure input voltage does not exceed the supply rails to avoid phase reversal, decouple supply pins with 0.1uF capacitors, and account for output swing typically 1.5V from the rails. Pricing as of 2026-08-29 starts near $0.0541 at LCSC.
LM358ADE4 - Dual General-Purpose Op Amp | Texas Instruments
Texas Instruments LM358ADE4 is a dual general-purpose operational amplifier with two amplifier circuits in an 8-SOIC package. The identified device operates at a 700 kHz gain-bandwidth product and has a slew rate of 0.3 V/us, providing a practical combination for general-purpose signal conditioning. Its two-circuit arrangement allows one package to implement functions such as buffering, voltage amplification, filtering, comparisons, and differential signal handling. An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify a voltage difference between its input terminals. In the broader hierarchy, an operational amplifier is a linear amplifier and analog signal-processing IC used within instrumentation, control, sensor, communications, and power-management systems. The LM358 family is associated with two amplifiers per package, making it useful where board area or component count matters. The LM358ADE4 provides a 700 kHz gain-bandwidth product, a 0.3 V/us slew rate, and two amplifier circuits in an 8-SOIC package. The wide SOIC body measures 0.154 inches, or 3.90 mm, in width according to the part listing. These characteristics suit moderate-bandwidth analog signals rather than demanding high-speed waveform or video applications. Each internal amplifier can be configured independently for standard inverting, non-inverting, summing, and feedback-based signal-conditioning circuits. The 8-SOIC package provides widely separated input, output, and power connections on a conventional surface-mount footprint. Its dual-channel architecture reduces the number of packages needed when two independent gain stages, two comparators, or mixed analog functions are required. The device is identified by Texas Instruments as an industry-standard dual operational amplifier, supporting design familiarity and straightforward board-level integration where the LM358 family is already qualified in the design. Typical uses include low-frequency sensor amplification, industrial control signals, audio preamplification, power-supply feedback loops, active filters, and general instrumentation. Two amplifiers in one package can also support comparator-style operation when saturation and switching behavior are acceptable. Because the gain-bandwidth product is 700 kHz, the device is better suited to modest signal bandwidth than precision audio or communications paths requiring substantially faster amplifiers. Design the surrounding feedback network to establish the intended closed-loop gain and bandwidth. Check output swing, input common-mode range, supply voltage, offset, input bias current, and output-current requirements in the manufacturer datasheet before finalizing the circuit. Place input and output components close to their associated pins, maintain a quiet supply path, and check that the selected SOIC footprint, pin orientation, and tube ordering code match the assembly process. This product page combines the exact ordering information, package characteristics, operating bandwidth, pin-compatible family alternatives, and practical design guidance needed to plan an LM358ADE4-based analog circuit before component sourcing and PCB layout.
LM358ADG4 - Dual 700kHz Op Amp, 8-SOIC | Texas Instruments
The Texas Instruments LM358ADG4 is a dual, general-purpose operational amplifier with two amplifier circuits in an 8-SOIC package. Its headline characteristics include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, input offset voltage of 2 mV, and operation from a single supply up to 16 V. The device is supplied in a tube and is intended for general-purpose signal-conditioning applications rather than precision or high-speed instrumentation. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier used to amplify the difference between two input voltages. It belongs to the amplifier IC hierarchy and supports common functions such as voltage buffering, signal amplification, active filtering, comparators, and analog signal conditioning. Because the LM358ADG4 contains two independent amplifiers in one package, it can reduce board area in dual-channel control, measurement, or interface circuits. Key features include two amplifier circuits, a 700 kHz gain-bandwidth product, a 0.3 V/µs slew rate, and a maximum specified supply voltage of 16 V. The 2 mV input offset voltage is suitable for general signal conditioning, although it is substantially less precise than the offset characteristics expected from dedicated precision amplifiers. Its SOIC-8 surface-mount package supports automated assembly and compact industrial, consumer, and instrumentation designs. The LM358 family architecture combines two general-purpose amplifiers with a single 8-pin package. Its bandwidth supports low-frequency amplification, buffering, filtering, and threshold-detection functions, while the 0.3 V/µs slew rate limits how quickly the output can follow larger input-driven voltage changes. Designers should account for that limitation in pulse, waveform, or feedback applications and keep operating points within the manufacturer’s electrical limits. Typical applications include sensor-signal conditioning, low-frequency active filters, industrial control interfaces, audio preamplifier stages, transducer amplifiers, and dual-channel threshold detection. Two amplifiers in one package are especially useful when a design needs matched circuit topology in two channels, provided both sections operate within compatible common-mode and output-swing conditions. For new layouts, follow the manufacturer’s pin-assignment and application guidance exactly, including bypass placement around the power supply. Keep feedback paths short, route sensitive input and output traces away from switching nodes, and verify stability with the actual source impedance, load, and compensation network. The SOIC-8 footprint also requires attention to thermal dissipation when either amplifier operates continuously near its output-current limit. This product page combines the verified LM358ADG4 specifications, package information, practical application guidance, comparison parameters, and confirmed pin-compatible alternatives. It is intended to help engineers evaluate whether this general-purpose dual operational amplifier fits a board-level signal-conditioning requirement before completing laboratory validation.
LM358ADGKR - Dual 30V 700kHz Op Amp | Texas Instruments
The Texas Instruments LM358ADGKR is a dual general-purpose operational amplifier with two independent amplifier channels, a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and 3 mV input offset voltage. The device is supplied in an 8-pin VSSOP DGK package for compact surface-mount designs. Its dual architecture allows both channels to operate from a common supply while supporting single-supply or split-supply operation. An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify voltage differences. The LM358 belongs to the operational-amplifier hierarchy within amplifier ICs, analog ICs, and semiconductor devices. Its two channels are internally frequency compensated, allowing straightforward use in common amplifier configurations without external compensation networks. The LM358A family's principal characteristics include two amplifiers per package, operation from a supply rated up to 30 V, a 700 kHz gain-bandwidth product, and a 3 mV offset-voltage specification. These ratings make the device suitable for general-purpose signal conditioning where moderate bandwidth, wide supply-voltage headroom, and low component count are more important than very high precision or very high speed. Each channel includes differential inputs and an output. With negative feedback applied, the closed-loop gain is set by the external resistor network rather than by the amplifier's very high open-loop gain. The manufacturer describes the LM358A as an industry-standard dual operational amplifier. Designers should therefore account for input common-mode range, output swing, supply voltage, input bias current, noise, offset, and stability requirements when choosing feedback and biasing components. Typical uses include low-frequency audio amplification, sensor-signal conditioning, DC error amplification in control systems, buffer stages, and general instrumentation. The dual channel count is useful when a board needs two independent amplifier functions, such as a transimpedance stage followed by an output-conditioning amplifier. The 8-pin VSSOP package also reduces board area compared with larger dual operational-amplifier packages. The primary design consideration is to verify signal amplitudes against the operating conditions for the selected supply voltage. Input and output voltages must remain within the limits stated in the manufacturer datasheet, and unused channels should be configured according to the recommended application circuit rather than left with floating inputs. Decoupling capacitors should be placed close to the supply pins to limit impedance in the supply-return path. This product page combines the official LM358A specifications with package, pinout, procurement, comparison, and design guidance. It also identifies pin-compatible options and explains the electrical checks required before changing an operational amplifier in an existing analog circuit.
LM358ADGKRG4 - Dual 700 kHz Operational Amplifier | Texas Instruments
Texas Instruments LM358ADGKRG4 is a dual, general-purpose operational amplifier with two independently usable amplifier channels, 700 kHz gain-bandwidth, 0.3 V/µs slew rate, and 2 mV input offset voltage. The device is supplied in an 8-pin VSSOP surface-mount package and is intended for general-purpose signal conditioning, buffering, amplification, and feedback applications. It supports a single-supply operating range up to 26 V and is also suitable for split-supply circuits. An operational amplifier, or op amp, is a high-gain differential amplifier that uses negative feedback to control gain and improve linearity. The LM358 integrates two independent, internally compensated amplifier sections into one package. Within the semiconductor hierarchy, it belongs to the amplifier IC family, which is part of the broader analog and mixed-signal IC category. Its dual-channel construction can reduce board area when a design needs two amplifier functions. Key characteristics include a 0.7 MHz gain-bandwidth value, 0.3 V/µs slew rate, and typical supply-current drain of 0.7 mA. The low 200 nA input-bias current supports higher-source-impedance sensing circuits, while the 2 mV input offset specification defines the typical baseline for dc input imbalance. These characteristics make the device suitable for general instrumentation, industrial control, sensor interfaces, and low-to-moderate-frequency analog signal paths. The LM358 architecture is based on bipolar transistor input stages with complementary output stages. Internally compensated operation simplifies closed-loop designs because no external compensation capacitor is required for typical voltage-follower and non-inverting amplifier configurations. The amplifier can operate from a single positive supply or from positive and negative supplies, allowing common-ground signal-conditioning arrangements to share the same device. Typical applications include transimpedance-style sensor front ends, audio preamplifier stages, active filters, comparators with suitable output interfacing, power-supply feedback networks, and industrial control interfaces. Its 0.3 V/µs slew rate is sufficient for general analog signals, while the 700 kHz bandwidth is better suited to audio, measurement, and control loops than to high-speed data acquisition. Designers should provide input and output bypassing close to the device, maintain adequate input and output voltage headroom, and verify common-mode range, output swing, and stability with the intended feedback network. Because the LM358 is not rail-to-rail at both input and output, supply selection must account for the signal range. The 8-pin VSSOP package also requires careful escape routing and thermal assessment in dense layouts. This page combines the LM358ADGKRG4 electrical characteristics, drop-in replacement assessment, comparison table, application guidance, and practical PCB design notes into a compact engineering reference for component selection and implementation.
LM358ADR2G - Dual 1MHz Op Amp, 3-32V | onsemi | SOIC-8
The onsemi LM358ADR2G is a dual general-purpose operational amplifier with two independent amplifiers, a 1 MHz gain-bandwidth product, and 3 V to 32 V supply operation in an 8-pin SOIC package. It supports single-supply or split-supply operation and accommodates input common-mode voltages that extend to ground or VEE, making it useful in industrial signal-conditioning circuits. An operational amplifier is a voltage-gain device used to amplify weak sensor signals, buffer inputs, implement active filters, compare voltages, and drive analog circuits. The LM358 belongs to the general-purpose operational-amplifier hierarchy, combining two amplifier channels in one package. Its ground-referenced common-mode capability is especially valuable in single-supply systems, where input signals often remain near the lower supply rail. Key characteristics include a 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, low power consumption, and common-mode input range extending to ground or VEE. The dual configuration reduces board area and package count when two amplifier channels are required. Commercial-temperature operation and surface-mount packaging make the device suitable for conventional industrial and commercial equipment rather than only low-volume prototyping. The LM358 series uses established general-purpose amplifier circuitry and is equivalent to one half of an LM324, as described by onsemi. It can operate from a single positive supply or from split bipolar rails, providing flexibility across instrumentation, control, and interface designs. Its 1 MHz bandwidth is sufficient for general-purpose audio, sensor, and feedback-loop applications, although it is not intended for precision or high-speed signal-path work. Typical uses include low-level sensor amplification, current-loop interfaces, differential voltage measurement, active filtering, threshold detection, and general feedback control. The device is especially appropriate when the signal can approach ground and the system cannot accommodate a rail-to-rail input stage. Because the common-mode range extends to ground or VEE, the amplifier can process signals near the negative rail without requiring a separate mid-supply bias. When laying out a circuit, place input and feedback components close to the corresponding amplifier pins and maintain short, low-noise routes around high-impedance inputs. Avoid long PCB traces between the source and noninverting input, particularly when sensing microvolt-level signals. Decoupling capacitors should connect to the supply and ground pins with minimal loop area to limit supply-noise coupling into the amplifier. This product reference combines manufacturer-family characteristics with practical pinout, application, and drop-in replacement guidance. It is structured to help engineers identify the correct onsemi ordering code, understand the 8-pin SOIC footprint, compare pin-compatible devices, and move from device selection into PCB-level implementation without relying on generic LM358 guidance.
LM358ADR2GH - Dual 3-32V Op Amp | onsemi | Industrial
onsemi LM358ADR2GH is a dual general-purpose operational amplifier with two amplifier circuits, a 3 V to 32 V supply range, and an 8-SOIC surface-mount package. The H suffix identifies the tape-and-reel packaging format associated with this onsemi orderable designation, supporting automated surface-mount assembly and standard pick-and-place workflows. A general-purpose operational amplifier is a voltage-controlled amplifier that uses external feedback to amplify voltage differences. LM358-type devices belong to the operational-amplifier hierarchy, combining differential input, high open-loop gain, output-current capability, and common-mode input operation. The onsemi LM358 family is widely used in instrumentation, buffer-amplifier, sensor-conditioning, and general feedback-control circuits where a dual amplifier provides more functionality than a single-channel device in the same package. The LM358ADR2GH provides two amplifier circuits, operates from 3 V to 32 V, and is identified as a commercial-temperature dual improved input-offset-voltage amplifier. Its listed slew rate is 0.6 V/us, while its gain-bandwidth product is not stated in the available product information. The device also supports single-supply or split-supply operation and has a common-mode input-voltage range extending to ground or VEE, allowing useful operation in circuits powered from a single positive rail. The 8-SOIC package has a stated body width of 3.90 mm, equivalent to 0.154 inch. Its dual-amplifier arrangement is useful when a circuit requires matched functional channels for signal conditioning, filtering, differential sensing, or feedback control. Because the operating and electrical limits vary with supply voltage, load, temperature, and configuration, designers should evaluate input common-mode range, output swing, stability, output-current capability, and offset behavior against their specific operating point before finalizing the circuit. Typical applications include current sensing in industrial instrumentation, buffering sensor outputs, amplifying low-level control signals, active analog filters, and general-purpose feedback-control loops. In single-supply systems, the ground-referenced common-mode capability can simplify signal conditioning around sensors whose output remains near the lower supply rail. In split-supply systems, both amplifier channels can process bipolar signals around the midpoint of the supply. PCB implementation should follow the manufacturer pin-description table and use a short, low-impedance feedback path. Place input, output, and compensation components close to the appropriate device pins, maintain a stable ground reference, and avoid long traces near switching nodes. Check the external feedback network for acceptable bandwidth and noise performance, and verify the chosen bypass capacitors against the application’s supply ripple and transient requirements. This product page combines the exact orderable designation, verified listing attributes, practical op-amp design guidance, and clearly scoped replacement information. The accompanying comparisons emphasize the engineering checks required for an eight-pin SOIC footprint: rail-to-rail compatibility cannot be assumed from the LM358 name alone, and load current, common-mode range, slew rate, offset voltage, bandwidth, and temperature grade should be reviewed before approving a substitution.
LM358ADRE4 - Dual 700 kHz Op Amp in 8-SOIC | Texas Instruments
The Texas Instruments LM358ADRE4 is a dual general-purpose operational amplifier with two amplifier circuits, a 700 kHz gain-bandwidth product, and an operating supply range of up to ±16 V, or 32 V total, in an 8-pin SOIC package. The LM358ADRE4 is supplied in tape-and-reel packaging for automated surface-mount assembly. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. Negative feedback defines the closed-loop gain and bandwidth, allowing one amplifier section to perform sensing, buffering, amplification, filtering, or signal-conditioning functions. A dual operational amplifier combines two amplifier channels in one package, reducing board area and simplifying power distribution in analog front ends. The LM358 family is widely used for general-purpose analog signal conditioning because each channel combines a 700 kHz gain-bandwidth product with single-supply or split-supply operation. The 8-SOIC arrangement provides separate inputs and outputs for both channels, along with common power and ground pins. This makes the LM358ADRE4 appropriate for industrial control, sensor interfaces, audio paths, and low-to-moderate-frequency conditioning circuits. The two independent channels can be configured as inverting amplifiers, non-inverting amplifiers, comparators, buffers, or transimpedance stages when suitable feedback and biasing networks are used. Designers should select resistor and capacitor values to meet the required signal bandwidth, gain, input impedance, output loading, and stability objectives. The device is a general-purpose solution rather than a rail-to-rail precision amplifier, so input common-mode range, output swing, offset voltage, and noise should be checked against the actual supply and signal levels. Typical applications include conditioning outputs from resistive sensors, buffering analog-to-digital converter inputs, amplifying low-level audio signals, and implementing active filters. In each case, maintaining adequate supply headroom and checking output-drive capability are important because the input and output operating ranges are not identical to the total supply rating. A practical PCB layout should place input, output, feedback, and compensation components close to the associated amplifier pins. Decoupling capacitors should be connected directly between the supply and ground pins, while long analog traces should be kept away from switching nodes and high-current return paths. The SOIC package is suitable for conventional reflow assembly and automated inspection. This product reference combines the exact ordering information for LM358ADRE4 with practical guidance on amplifier configuration, application fit, PCB implementation, and drop-in comparison. It also highlights which technical details should be confirmed in the manufacturer datasheet before release to production.
LM358ADRG4 - Dual 700kHz Op Amp, 8-SOIC | Texas Instruments
The Texas Instruments LM358ADRG4 is a general-purpose dual operational amplifier containing two independent, high-gain, frequency-compensated amplifiers, with a gain-bandwidth product of 700 kHz and slew rate of 0.3 V/us in an 8-pin SOIC package. The device operates from a single supply or split supply and supports an operating voltage range of ±1.5 V to ±16 V. Its two independent channels make it suitable for dual-signal conditioning, buffered sensing, and general analog amplification. An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify the difference between two input voltages. The LM358 belongs to the operational-amplifier hierarchy within analog signal-chain ICs and power-management applications. Frequency compensation allows each channel to provide stable closed-loop operation in common noninverting, inverting, voltage-follower, summing, and comparator configurations without external compensation networks. The LM358ADRG4 provides two amplifier sections in one compact 8-SOIC package, reducing board area compared with separate single-channel amplifiers. Its 700 kHz gain-bandwidth product supports moderate-bandwidth signal paths, while the 0.3 V/us slew rate limits large-signal response speed. The wide ±1.5 V to ±16 V operating range accommodates both low-voltage and conventional bipolar analog systems, and the split-supply capability allows operation around a nonzero midpoint voltage. Each amplifier channel includes differential inputs, an output, and independent biasing. Internal compensation is a key practical feature because it eliminates the external frequency-compensation capacitor commonly associated with general-purpose op-amp designs. However, stable operation still depends on correct feedback routing, suitable output loading, and appropriate input and output voltage ranges. The device is intended for linear amplification rather than high-speed, low-voltage, or rail-to-rail precision applications. Typical uses include sensor-signal conditioning, audio preamplification, motor and actuator control loops, active filtering, low-current buffer stages, and general dual-channel instrumentation. The two channels can amplify related signals or perform separate functions, such as sensing and reference buffering, while keeping the implementation in one standard surface-mount package. For PCB design, place input and output connections away from high-current switching paths, maintain short feedback traces, and use a local bypass capacitor from the supply pin to ground. Check input common-mode and output-swing limits against the actual single- or split-supply rails. Avoid relying on the LM358 for millivolt-level precision because its input offset and bias characteristics are appropriate for general-purpose rather than precision instrumentation. This page combines device specifications, application guidance, drop-in replacement comparisons, and design notes to support faster engineering selection. It also highlights where an alternate LM358 grade may offer a better fit for temperature, automotive qualification, or manufacturing requirements.
LM358AM - Dual 8-SOIC Operational Amplifier | Texas Instruments
The Texas Instruments LM358AM is a dual general-purpose operational amplifier with two independent, internally frequency-compensated amplifier channels in an 8-pin SOIC package. The device is designed for operation from a single power supply over a wide voltage range, providing a practical solution where two amplified signals must be processed by one compact analog IC. The verified product information identifies the LM358AM as a standard, general-purpose, two-circuit amplifier and describes its low-power consumption, high gain, and wide operating-voltage capability. An operational amplifier, or op-amp, is a voltage-controlled differential amplifier whose closed-loop behavior is determined mainly by external feedback components. The LM358 belongs to the broad hierarchy of operational amplifiers, analog amplifiers, analog signal-conditioning ICs, and semiconductor devices. Its two internally compensated channels can perform common tasks such as voltage amplification, buffering, summing, comparisons, active filtering, and feedback control when configured with suitable external resistors and capacitors. The principal advantages of choosing a dual amplifier are functional integration and reduced board area. Two independent amplifiers in one LM358AM package can replace two separate single-channel devices while preserving the familiar SOIC-8 footprint. The manufacturer describes the series as suitable for general-purpose applications and emphasizes its combination of low power consumption, high gain, and a wide supply-voltage range. Exact voltage, current, gain-bandwidth, input-offset, and temperature limits require confirmation from the full manufacturer datasheet because those values were not included in the supplied web records. The architecture is based on two independent, high-gain, internally frequency-compensated operational amplifiers. Internal frequency compensation avoids the need for an external compensation capacitor in ordinary closed-loop configurations, simplifying amplifier selection and PCB design. Because the channels are independent, one can amplify a sensor signal while the other performs a different function, such as comparison, current-to-voltage conversion, active filtering, or an output driver. Typical uses include industrial sensor conditioning, low-cost control loops, audio preamplification, current sensing, comparator-style threshold detection, and general analog signal processing. Single-supply operation is particularly useful in embedded equipment because the amplifier can operate from a positive rail and ground. Designers must still check input and output common-mode limits, output-swing behavior, load capability, and stability for the intended configuration before releasing production hardware. PCB implementation should preserve the exact pin assignment of the chosen SOIC-8 manufacturer variant and provide a solid ground return. Decoupling capacitors should be placed close to the supply pins, while feedback resistors and compensation networks should be kept short to minimize noise pickup and parasitic instability. The LM358AM is not rail-to-rail by implication alone; input and output behavior must be verified against the relevant datasheet limits. This product record combines verified distributor and manufacturer references, package information, commercial availability links, and practical selection guidance. It also separates documented facts from missing numeric parameters so engineers can cross-check voltage limits, pricing, compliance, and production details against the authoritative LM358 datasheet before design release.
LM358AM/NOPB - Dual Low-Power Op Amp | Texas Instruments
Texas Instruments LM358AM/NOPB is a low-power, dual operational amplifier in an 8-pin SOIC package. The device contains two independent amplifiers, operates from a 3 V to 32 V single supply, and provides a 700 kHz gain-bandwidth product with 0.3 V/us slew rate. Its input common-mode range extends toward the supply rails, making it suitable for low-voltage signal conditioning, buffering, and general-purpose analog control. An operational amplifier is a voltage-controlled differential amplifier that uses feedback to create stable, programmable gain. The LM358 belongs to the general-purpose operational-amplifier family within the broader analog IC and semiconductor hierarchy. Unlike precision or rail-to-rail designs, the LM358 is primarily intended for economical systems that operate from single or dual supplies and need moderate bandwidth, input common-mode range, and output-current capability. The two amplifier sections are electrically independent, allowing each channel to process a different signal within the same package. Key features include a 700 kHz gain-bandwidth product, 0.3 V/us slew rate, low-power operation, and an output-current capability cited as 20 mA. These characteristics support common tasks such as sensor amplification, error amplification, voltage comparison, active filtering, and signal buffering without requiring two separate amplifier packages. The LM358AM/NOPB is specified for a 3 V to 32 V supply range and an input common-mode range of ±1.5 V to ±16 V, depending on the operating configuration. Because it is not rail-to-rail, output swing and input range depend on the selected supply voltage and common-mode headroom. Designers should preserve those margins when processing signals close to the positive or negative rail. Typical uses include 5 V sensor interfaces, industrial control loops, audio preamplifier stages, battery-powered instrumentation, active filters, and comparator-style feedback networks. The 8-pin SOIC package is easy to assemble on conventional through-hole-compatible PCB land patterns and supports automated manufacturing. The two-amplifier configuration can also reduce board area when two independent analog channels are required. Design consideration: keep feedback networks close to the amplifier pins, provide stable bypass capacitance on the supply rail, and avoid forcing either input beyond the specified common-mode range. Output current and total power dissipation must be checked against the actual load, supply voltage, and ambient temperature because the two channels can contribute independently to device heating. This page combines the manufacturer product information, package details, application guidance, pin mapping, and drop-in replacement analysis into a focused engineering reference for selecting, laying out, and qualifying the LM358AM/NOPB.