Amplifier ICs
بەرهەمەکان (3,200+)
LM358AMX - Dual 3-32V Op Amp in 8-SOIC | onsemi
The onsemi LM358AMX is a dual, general-purpose operational amplifier with two independent amplifier channels, a 3 V to 32 V power-supply range, and an 8-SOIC package. It provides a minimum common-mode rejection ratio of 65 dB, a large-signal voltage gain of 100 dB, and a typical input offset voltage of 3 mV. The part is designed for low-cost signal conditioning, feedback-control, and analog-signal amplification applications. An operational amplifier, or op amp, is a high-gain differential amplifier whose closed-loop behavior is determined mainly by external feedback components. The LM358 belongs to the dual-operational-amplifier hierarchy, which sits within analog ICs and the broader semiconductor category. Its two channels can amplify separate signals or work together in differential, summing, comparator-style, and current-feedback configurations. The principal characteristics of the LM358AMX include internal frequency compensation for unity-gain operation, two amplifier circuits in one package, and operation from a single positive supply of 3 V to 32 V. The 100 dB large-signal voltage gain supports accurate closed-loop amplification when paired with conventional resistor networks. A minimum 65 dB common-mode rejection ratio helps reduce common-mode input signals when the input waveform contains large DC or externally coupled noise components. The internally compensated architecture simplifies the implementation of unity-gain voltage followers and standard inverting or non-inverting gain stages. Although the amplifier operates from a single positive supply, its input common-mode range does not extend fully to the negative rail. Designers should also account for input offset voltage, output-current capability, supply-voltage headroom, and the finite output-voltage swing when setting resistor values and signal ranges. Typical uses include industrial sensor interfaces, low-voltage control loops, audio preamplifier stages, current-monitoring circuits, and general instrumentation. In a sensor interface, the amplifier can convert a small transducer signal into a voltage referenced to ground. In a power-control application, it can amplify an error signal before driving a transistor or power stage, provided the feedback network maintains stable closed-loop operation. For a new design, begin by confirming the required input and output voltage ranges against the operating supply. Place the bypass capacitor close to the supply pin, keep feedback traces short, and avoid long paths adjacent to switching nodes. The SOIC outline allows the same footprint to be considered for compatible dual general-purpose amplifier options, but electrical behavior and supply limits should be checked before substitution. This product record combines the exact LM358AMX package identity, channel and supply characteristics, cross-reference options, and practical PCB guidance with a parameter-by-parameter comparison. It is designed to accelerate component selection for analog signal-conditioning and control designs while keeping replacement decisions traceable to manufacturer and distributor documentation.
LM358AMX/NOPB - Dual 32V 1MHz Op Amp | Texas Instruments
The Texas Instruments LM358AMX/NOPB is a dual general-purpose operational amplifier with two independent amplifier circuits, a 32 V maximum supply rating, 1 MHz gain-bandwidth product, and an 8-pin SOIC package. The manufacturer specifies a 0°C to 70°C operating-temperature range for this ordering variant, making it appropriate for commercial and industrial equipment that does not require an extended-temperature grade. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare an inverting input with a non-inverting input. The LM358 family belongs to the broader hierarchy of operational amplifiers, analog amplifiers, and semiconductor signal-conditioning devices. Two amplifiers in one package can provide gain, buffering, active filtering, current-to-voltage conversion, or general feedback control when their power requirements and electrical limits suit the circuit. The LM358AMX/NOPB combines two general-purpose amplifier sections with a 32 V supply capability and 1 MHz bandwidth. Its dual-circuit configuration saves board area compared with two separate single amplifiers, while the SOIC (D) package supports conventional surface-mount assembly. The 0°C to 70°C rating is the principal distinction to verify when replacing this part in equipment exposed to temperatures outside the commercial range. Each amplifier section operates from the same external supply pins, and the package provides separate input and output connections for both channels. The manufacturer identifies the device as a standard general-purpose amplifier rather than a precision, low-noise, high-speed, or rail-to-rail-input part. Designers should therefore base input-signal range, offset, bias-current, slew-rate, and output-swing decisions on the corresponding LM358-N electrical characteristics rather than assume the behavior of newer amplifier families. Typical uses include two-channel sensor conditioning, buffered analog measurements, audio preamplification, active filters, comparator-style threshold circuits, and general industrial control. A single package is especially useful when two modest-bandwidth signal channels share the same board and supply rails. Independent amplifier channels also allow one section to perform signal conditioning while the other handles monitoring or feedback within the same system. For PCB design, use the manufacturer's pin-description table when assigning tracks because exposed-pad, thermal, and no-connect details depend on the exact package drawing. Place the input network close to the corresponding amplifier pins, keep feedback-loop routing compact, and provide adequate decoupling between the supply pins and ground. Confirm output swing and common-mode limits at the selected supply voltage before using the device near either rail. This product page combines the manufacturer's exact ordering information with practical guidance on package reuse, dual-amplifier implementation, thermal-range verification, and same-footprint sourcing. It helps engineers distinguish the 32 V, 1 MHz commercial-temperature device from parts with different pinouts, package styles, extended-temperature ratings, or substantially different amplifier performance.
LM358AN - Dual 1MHz Op Amp, 3-36V Single Supply | Texas Instruments
The Texas Instruments LM358AN is a dual, general-purpose operational amplifier providing two independent channels in an 8-pin PDIP (through-hole) package, with an A suffix indicating the lead-free (RoHS-compliant) finish. Each channel offers a 1.0 MHz unity-gain bandwidth, 0.3 V/us slew rate, and operation from a single 3 V to 36 V supply, making it the standard dual single-supply op amp for cost-sensitive analog signal conditioning. An operational amplifier is an analog building block that amplifies the voltage difference between its two inputs. The LM358 belongs to the single-supply, rail-to-rail-input-capable general-purpose family: it is designed to run from one positive rail and a ground reference, so its input common-mode range extends from 0 V up to roughly 1.5 V below the positive supply. This topology sits at the bottom of the hierarchy of integrated circuit amplifiers: operational amplifier -> voltage-feedback amplifier -> amplifier IC -> analog semiconductor. Key features include differential input stage trimming for low offset, internal frequency compensation so no external nulling or compensation components are required, and output-stage design that sources up to 40 mA and sinks up to 20 mA while staying within a few tens of millivolts of the supply rails. The two amplifiers are independent, allowing them to be used in separate signal chains or in differential and instrumentation configurations within a single package. Technically, the LM358 uses a class-B output stage, so crossover distortion around 0 V output is a consideration in precision AC applications. The open-loop gain is typically 100 dB with a unity-gain bandwidth of 1 MHz, so closed-loop stability depends on keeping the feedback network noise-gain flat across the frequency range. Input bias current of roughly 20 nA and input offset voltage of a few millivolts make it appropriate for impedance levels above about 100 kOhm. Typical applications include DC amplifier stages in sensor front ends, low-side current sensing with a shunt, active filters, comparators with reference inputs, audio mixers, and general instrumentation in industrial control and consumer equipment. The DIP-8 package is favored for through-hole assembly, prototype boards, and legacy repair where a surface-mount footprint would be impractical. When designing with the LM358AN, keep input and output signals within the input common-mode range, and remember that at supply voltages below about 5 V the output swing limitations consume a larger share of the rail-to-rail span. For low-offset or low-noise instrumentation, add an external offset trim or select a higher-grade precision amplifier instead. This page consolidates distributor availability, drop-in replacement options, and application-specific design guidance for the LM358AN into a single engineering reference that goes beyond a manufacturer datasheet.
LM358AN/NOPB - Dual 32 V Op Amp | Texas Instruments
The Texas Instruments LM358AN/NOPB is a dual operational amplifier containing two independent, high-gain, internally frequency-compensated amplifiers in an 8-pin PDIP package. The device supports operation from a single supply across a wide voltage range, with the LM358 family identified for operation up to 32 V and a gain-bandwidth product of 1 MHz. The LM358AN/NOPB designation identifies the PDIP package version associated with the Texas Instruments LM358 family. An operational amplifier is an analog signal-processing IC that uses differential input voltage to control an output voltage. A dual device contains two amplifiers that operate independently but share a supply. The LM358 belongs to the general-purpose operational-amplifier hierarchy, where its differential input stage, high open-loop gain, internal frequency compensation, and wide supply range make it suitable for signal conditioning, amplification, filtering, and control applications that do not require rail-to-rail input or output operation. The principal family-level characteristics include two amplifier circuits, a maximum supply rating of 32 V, a 1 MHz gain-bandwidth product, approximately 700 kHz bandwidth for the LM358AN comparison entry, and a slew rate of 0.3 V/us. Each amplifier has two differential inputs and one output. Internal frequency compensation removes the need for an external compensation network in many conventional closed-loop configurations. The wide operating supply permits use in both low-voltage 5 V systems and higher-voltage industrial control circuits. The two amplifiers share power-supply connections but retain separate input and output pins, allowing one section to perform sensing or amplification while the other performs buffering, level conversion, or an additional control function. Because the device is intended for single-supply operation, its common-mode input range and output swing are important design constraints. Engineers should verify those limits against the exact operating condition required by the application rather than assuming behavior from a rail-to-rail amplifier. Typical uses include transducer-signal conditioning, low-frequency active filters, comparators with an external reference, loop-error amplifiers, audio preamplification, and general-purpose analog control. The dual configuration is especially useful when a board needs two independent analog channels without allocating space for two separate amplifier packages. The internal compensation also simplifies designs requiring stable gain, although stability still depends on the selected feedback network, output loading, and signal frequency. A primary design consideration is input and output range. On a single 5 V supply, the LM358 does not necessarily swing rail to rail, so the signal and feedback network must remain inside its common-mode and output-swing limits. Decoupling capacitors should be placed close to the supply pins, and unused amplifier sections should be configured conservatively rather than left floating. Input-referred offset and bias current should also be checked against the source impedance and required measurement accuracy. This product page combines the exact LM358AN/NOPB ordering identity, manufacturer family specifications, package details, sourcing guidance, and engineering-focused application analysis. It also organizes same-footprint alternatives, comparison parameters, and practical design notes so engineers can assess fit before committing to a PCB and production BOM.
LM358AP - Dual 30V 700kHz Op Amp | Texas Instruments
Texas Instruments LM358AP is a dual general-purpose operational amplifier with two independent amplifiers, a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and an 8-pin PDIP package. It operates from 3 V to 30 V, supports input and output common-mode ranges suitable for single-supply signal conditioning, and is specified for 0°C to 70°C operation. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to perform a defined gain function. The LM358 belongs to the dual operational amplifier, voltage-feedback amplifier, analog IC, and semiconductor hierarchy. Its two internally compensated channels make it suitable for sensor interfaces, transducer amplifiers, buffer stages, and general-purpose analog control circuits without requiring a separate single amplifier package. The principal performance figures are a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and approximately 2 mV input offset voltage. These characteristics make the LM358AP suitable for low-to-moderate frequency precision analog circuits. Its dual configuration provides channel-to-channel integration, while the wide 3 V to 30 V supply range allows operation from a single low-voltage rail or from split supplies. The device is available in an 8-pin PDIP package for through-hole PCB assembly. Each channel uses a differential input stage, voltage-gain stage, and output stage, with internal compensation providing stable operation without an external compensation capacitor. Although the device is commonly associated with single-supply operation, its common-mode input range does not extend all the way to the positive supply rail. Designers should therefore verify the signal excursion against the common-mode limits before using the amplifier directly at the top of a low-voltage supply. Typical uses include low-current sensor conditioning, buffered control inputs, audio preamplifier stages, active filtering, and general-purpose instrumentation. In a sensor interface, the LM358AP can amplify a small transducer signal while its dual channels support a second stage such as an inverter, buffer, or active filter. The 700 kHz bandwidth provides ample margin for slow sensor signals and low-frequency control loops. PCB layout should keep input traces short, place bypass capacitance near the supply pin, and route output returns independently from sensitive input paths. Although the PDIP package is through-hole and easy to prototype, its lead pitch requires adequate clearance from adjacent components. Input and output nodes should also be kept apart to reduce parasitic feedback and oscillation risk. This product page combines the LM358AP electrical characteristics, package details, application guidance, compatible replacements, and practical PCB considerations in a format that helps engineers evaluate the device before committing a through-hole design to production.
LM358APE4 - Dual 700kHz Op Amp | Texas Instruments
The Texas Instruments LM358APE4 is a dual general-purpose operational amplifier with two push-pull output circuits, a 700 kHz gain-bandwidth product, and a 0.3 V/us slew rate, housed in an 8-pin dual in-line package. The LM358APE4 is designed for general-purpose signal conditioning when one component can provide two amplifiers in the same package. An operational amplifier is a voltage-gain device that uses differential input voltage to control an output voltage. Operational amplifiers belong to the analog amplifier hierarchy and are commonly used in voltage followers, noninverting amplifiers, summing circuits, comparators, filters, and current-control loops. A dual package provides two amplifiers in one device, reducing board area and simplifying multi-channel designs. The LM358APE4 provides a 700 kHz gain-bandwidth product and a 0.3 V/us slew rate. Its supply current is specified at 0.7 mA typical, supporting power-conscious signal-processing designs. The dual push-pull output structure allows the amplifiers to source and sink output current, while the through-hole 8-DIP package supports conventional PCB assembly and socketed prototypes. This part is identified as a general-purpose amplifier rather than a precision or high-speed device. Its bandwidth is adequate for audio-frequency signal conditioning, sensor interfaces, and low-to-moderate-frequency control loops. Design engineers should account for the finite gain-bandwidth product when selecting feedback resistors and should evaluate output-voltage swing against the selected supply voltage. Typical uses include dual-channel sensor conditioning, current-to-voltage conversion, active filtering, differential input stages, and general instrumentation. Two independent amplifiers in one package are especially useful when both channels process related or complementary signals, such as an analog sensor pair or an excitation-and-measurement arrangement. For a new PCB, use the standard 8-DIP footprint and observe the pin assignments shown in the manufacturer datasheet. Place input and feedback components close to their associated amplifier pins to minimize parasitic capacitance and feedback-loop instability. Decoupling capacitors should connect to a low-impedance ground plane with short return paths. This page combines the LM358APE4 electrical characteristics, practical application guidance, drop-in alternatives, package details, and selection trade-offs into an engineering-focused resource for evaluating the dual operational amplifier in instrumentation, control, and analog signal-conditioning designs.
LM358APG4 - Dual Op Amp, 8-PDIP | Texas Instruments
The Texas Instruments LM358APG4 is a dual general-purpose operational amplifier in an 8-pin PDIP package. It provides two amplifier channels in one IC, giving compact analog signal conditioning for industrial, instrumentation, and control systems. The device is identified as the LM358APG4 ordering variant and is associated with a commercial ambient-temperature range of 0°C to 70°C. An operational amplifier, commonly called an op amp, is an analog integrated circuit that amplifies the voltage difference between its two input terminals. Its place in the analog signal-chain hierarchy is amplifier IC → operational amplifier → analog signal-conditioning IC. The LM358APG4 combines two general-purpose amplifier channels in one package, reducing component count compared with separate single-channel amplifiers where the electrical and layout requirements allow it. The principal implementation features are its dual-circuit architecture, general-purpose classification, and 8-pin PDIP package. The DIP format remains useful in educational systems, laboratory prototypes, legacy control equipment, through-hole assembly, and repair products where socketed DIP devices or hand assembly are preferred. Because the commercial part is intended for a 0°C to 70°C ambient range, it should not be treated as an automotive or extended-temperature selection without selecting a part explicitly rated for those conditions. The LM358 family is commonly positioned for general-purpose signal amplification, buffering, feedback networks, analog comparisons, and control-loop functions. In a practical circuit, the selected device, external resistors, and any feedback network establish gain and bandwidth, while the power-supply voltage determines the available common-mode and output-voltage range. Designers should therefore verify voltage rails, input signal range, output swing, load conditions, and stability requirements against the manufacturer datasheet for the exact ordering code. Typical LM358APG4 applications include sensor-signal conditioning, low-frequency analog amplification, instrumentation interfaces, industrial control modules, educational electronics, and service or repair assemblies. The DIP package can simplify through-hole prototyping and socket-based replacement, although it occupies more PCB area than an equivalent surface-mount dual op amp and generally does not support automated reflow assembly. The primary design consideration is package and temperature fit rather than channel count. Verify that the board accepts an 8-pin PDIP footprint, confirm the pin orientation, and review the manufacturer pin-description table before assigning amplifier inputs, outputs, power, and compensation connections. Avoid assuming that every generic LM358-compatible part has identical electrical limits or temperature qualification. This product page consolidates the exact LM358APG4 package and ordering information, practical temperature considerations, pin-compatible replacement candidates, and application-oriented design guidance. It supports faster engineering comparison while keeping final component selection tied to the manufacturer datasheet and verified cross-reference information.
LM358APT - Dual Low-Power Op Amp in 8-TSSOP | STMicroelectronics
The STMicroelectronics LM358APT is a dual, general-purpose operational amplifier packaged in an 8-TSSOP. It contains two independent, internally compensated amplifiers with a common power supply, making it suitable for signal conditioning, sensing, buffering, and control applications. The distributor catalog identifies the LM358APT as a standard general-purpose amplifier with two amplifier circuits in an 8-TSSOP surface-mount package. An operational amplifier is an analog building block that amplifies the difference between two input voltages. The LM358 combines two such amplifier channels in one compact package, reducing component count and simplifying PCB routing. In a dual amplifier, one channel can perform signal conditioning while the other provides feedback, filtering, or an independent control function. Its low-power biasing makes it appropriate for battery-operated and embedded systems where each active circuit consumes power continuously. The principal benefits of the LM358APT are integration, low power consumption, and flexible single- or dual-supply operation. Two amplifiers in one package conserve board area and can reduce the number of external ICs required for comparison, conditioning, and current-feedback applications. Because both channels share the same supply pins, the circuit designer can also establish common rail and ground references throughout the analog section of the board. The LM358 architecture is widely used in general-purpose analog designs because each channel provides high open-loop voltage gain, differential input capability, and internal frequency compensation. These characteristics simplify closed-loop amplifier design without requiring an external compensation network. Engineers commonly use the device around sensor interfaces, transducers, audio preamplifier stages, and slow closed-loop control loops. Typical uses include conditioning a bridge or resistive sensor, buffering an analog-to-digital converter input, amplifying instrumentation signals, implementing window comparators, and driving the input stage of a power-control circuit. Its internal compensation and dual-channel organization are particularly useful in compact embedded products where each additional package increases board cost and routing complexity. PCB layout should keep input and feedback traces short, place input-biasing resistors close to the relevant pins, and route the ground connection directly to the package ground pin. Decoupling capacitors should be connected with minimal trace length. Because an operational amplifier can respond to unintended feedback caused by parasitic capacitance, clean layout is often more important than adding large external capacitors to compensate for poor routing. This page combines the LM358APT catalog identity, package information, cross-reference options, and practical PCB guidance. It also organizes pin-level information, application guidance, and design cautions so engineers can evaluate the part quickly before starting a board layout or prototype build.
LM358APW - Dual 30V 700kHz Op-Amp | TI | TSSOP-8
The Texas Instruments LM358APW is an industry-standard dual operational amplifier delivering two independent, internally compensated, high-gain op-amp channels rated for 30V supplies with a 700 kHz gain-bandwidth product, housed in an 8-pin TSSOP (PW) surface-mount package. A dual operational amplifier is an integrated circuit that combines two complete op-amp stages on a single silicon die, sharing one power supply while keeping the signal paths fully independent. Within the amplification hierarchy, the op-amp sits above individual transistors as an analog signal-conditioning block, and the LM358 family is the archetypal general-purpose amplifier IC used throughout industrial, automotive-adjacent, and consumer electronics for decades. Key features include a wide supply range that accepts single supplies from roughly 3V up to 30V or dual supplies, low supply-current drain of 0.7 mA (typical) that is essentially independent of supply voltage, and a common-mode input voltage range that includes ground. Ground-including common-mode input allows direct sensing of signals near 0V without negative rails, which is the defining advantage of the LM358 in single-supply systems. Architecturally, the LM358 uses internally frequency-compensated bipolar stages, so no external compensation capacitors are required for unity-gain stability. The enhanced LM358A grade tightens key limits such as input offset voltage compared with the base LM358, giving designers additional accuracy margin while preserving the familiar behavior and pinout of the industry-standard part. Typical applications include single-supply transducer signal conditioning, active filters and comparators in industrial controls, DC gain blocks and summing amplifiers in test equipment, and general-purpose amplification in battery-powered consumer devices where low quiescent drain extends operating life. A key design consideration: the output stage is a classic bipolar design that can sink current to ground but does not pull close to the positive rail without a pull-up, so plan for rail-to-rail headroom limits near the supply maximum. This page consolidates distributor sourcing channels, drop-in alternatives within the same TSSOP-8 footprint, engineering design notes, and parameter comparison data not typically found together in the manufacturer datasheet.
LM358APWE4 - Dual 700 kHz Op Amp | Texas Instruments
The Texas Instruments LM358APWE4 is a dual general-purpose operational amplifier with two amplifier circuits, a 700 kHz gain-bandwidth product, and an 8-TSSOP package. The device is supplied in a tube and uses a gull-wing surface-mount package measuring 4.40 mm wide. An operational amplifier is an analog signal-conditioning IC that compares two input voltages and amplifies their difference. The LM358 family belongs to the operational-amplifier hierarchy within analog amplifier ICs. Each of the two LM358 amplifier channels can support common-mode input operation near ground, making the device suitable for single-supply systems that measure, buffer, amplify, or control signals referenced to 0 V. The LM358APWE4 combines a typical slew rate of 0.3 V/us with a 700 kHz gain-bandwidth product. Its typical input-offset voltage is 2 mV, while the documented maximum offset is 5 mV. Typical input-offset current is 2 nA and typical input-bias current is 15 nA. A typical supply-current drain of 0.7 mA supports low-power analog signal chains, although the exact operating-current limit should be checked against the manufacturer datasheet for the selected supply voltage. Each channel is internally frequency compensated and supports a common-mode input range that includes ground. The 32 V differential input rating defines the maximum voltage permitted between the two input terminals. In practical signal-conditioning circuits, these characteristics make the LM358 suitable for noninverting and inverting amplifiers, voltage followers, cross-coupled instrumentation stages, active filters, comparators, and low-frequency closed-loop control loops. The LM358APWE4 is particularly appropriate for industrial control, sensor-interface, audio, and embedded measurement systems operating from a single supply. Its ground-referenced common-mode capability simplifies designs that sense low-voltage sensor outputs without a negative supply. The two independent channels can also be used together for differential amplification, active filtering, or a general-purpose analog front end. Circuit design should preserve adequate output-voltage headroom under load and account for input bias-current error at high source impedance. Decoupling capacitors should be placed close to the supply pins, and sensitive analog traces should remain away from switching nodes. Because the two channels share supply pins, their total supply-current demand and thermal dissipation must be considered together. This page combines package and electrical characteristics, practical application guidance, design checks, and pin-compatible alternatives. It is intended to help engineers evaluate whether the LM358APWE4 fits a new design or an existing 8-TSSOP analog board before committing to a footprint and supply configuration.
LM358APWRG4 - Dual 700 kHz Op Amp | Texas Instruments
The Texas Instruments LM358APWRG4 is a dual general-purpose operational amplifier in an 8-pin TSSOP package. Each amplifier provides a 700 kHz gain-bandwidth product, 0.3 V/us slew rate, 80 dB common-mode rejection, and 2 mV input offset voltage, making the device suitable for general signal conditioning from a single 5 V supply. An operational amplifier is an analog amplifier that uses very high open-loop gain to increase the voltage applied across an impedance connected to its inverting input. With external feedback, a practical LM358 stage can operate as a voltage amplifier, current-to-voltage converter, comparator, or active filter. The LM358 family belongs to the broader operational amplifier and analog signal-processing IC categories. The LM358APWRG4 uses a 0.7 mA typical supply-current drain, supports single or dual supplies, and provides a common-mode input range that includes the ground rail. Its 0.3 V/us slew rate limits large-signal bandwidth, while the 80 dB CMRR helps reject common-mode noise. These characteristics make it appropriate for transducers, feedback loops, sensor interfaces, audio paths, and low-to-moderate-frequency control systems. The device operates from 5 V in the characterized operating condition and belongs to the 26 V maximum supply-voltage class of the LM358 family. Its operating temperature range is 0 C to 70 C for this ordering code. The LM358 dual-amplifier configuration allows both channels to share one package while preserving independent inputs and outputs, reducing board area compared with two single-amplifier packages. Common applications include buffering sensor outputs, amplifying low-level signals, summing analog signals, driving ADC input stages, implementing active filters, and providing feedback around analog control loops. Because the LM358 output stage is not rail-to-rail, output swing limits and input common-mode restrictions must be checked against the actual signal range before layout is finalized. Place input, feedback, and bypass capacitors close to their associated pins, and route sensitive input traces away from switching nodes and high-current paths. Verify stability with the manufacturer guidance for capacitive loads, because the 0.3 V/us slew rate and output-capacitance limits can affect transient response. The TSSOP-8 package also requires careful thermal assessment when both channels operate continuously near the supply rail. This page combines the device specifications, verified sourcing records, application engineering guidance, and same-footprint replacement analysis to support faster component selection and PCB planning.
LM358AWDT - Dual 1.1MHz Low-Power Op Amp | STMicroelectronics
STMicroelectronics LM358AWDT is a low-power dual operational amplifier packaged in an 8-pin SOIC. The device contains two amplifiers, operates from a single supply, and is specified at 1.1 MHz unity-gain bandwidth with a 70°C maximum operating temperature. Its general-purpose design makes it suitable for signal conditioning, buffering, and analog amplification in industrial and embedded systems. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. The LM358 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Each amplifier in the dual package can amplify noninverting or inverting signals, while negative feedback defines the closed-loop gain and bandwidth. This makes the device useful where a sensor, divider, comparator, or analog front end needs a higher-current drive than the preceding circuit can provide. The LM358AWDT offers two independent amplifiers in one 8-SOIC package, reducing board area compared with two separate single amplifiers. Its 1.1 MHz bandwidth supports general-purpose signal paths operating well below megahertz data rates. The low-power architecture also makes the device appropriate for battery-operated, test, measurement, and embedded-control equipment, subject to the device-specific limits in the manufacturer datasheet. Operationally, the part combines input, output, and biasing functions within each amplifier section. The output stage must remain within its voltage limits, so designers should provide suitable load current and verify common-mode and output-swing conditions at the actual supply voltage. Feedback components set the gain and bandwidth; choosing resistor and capacitor values consistent with the amplifier’s stable operating region is essential for predictable behavior. Typical applications include buffering sensor outputs, amplifying low-level analog signals, active filtering, bridge or differential signal conditioning, and general feedback control. Two amplifiers in one package can also handle a matched pair of channels when their grounding, decoupling, and signal paths are laid out carefully. The same package size simplifies replacement with compatible SOIC-8 dual operational amplifiers when their electrical ratings and pin functions have been checked. The primary layout consideration is decoupling. Place a suitable supply bypass capacitor close to the power pin, keep the feedback loop compact, and route output and input signals away from the noisy supply and ground-return paths. Avoid using the ground lead as a high-current return for external loads, because resistance in the ground trace can introduce gain error and channel coupling. This product page combines the LM358AWDT ordering information, package identification, operating limits, verified listings, drop-in candidate analysis, and practical implementation guidance. It also highlights where engineers must consult the manufacturer datasheet for detailed pin descriptions, input limits, offset, current, noise, and recommended application circuits before completing a production design.
LM358AWPT - Low-Power Dual Op Amp | STMicroelectronics | TSSOP-8
The STMicroelectronics LM358AWPT is a low-power, dual operational amplifier packaged in an 8-pin TSSOP. It integrates two general-purpose amplifier channels in one surface-mount package, with a listed output-current capability of 40 mA. The LM358AWPT combines the familiar dual-amplifier organization with a compact power-surface-mount footprint, making it suitable for signal conditioning, buffering, feedback control, and low-frequency analog circuits. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. A dual operational amplifier contains two amplifier sections that share common supply and ground connections but can process separate signals. In the broader semiconductor hierarchy, the LM358 belongs to the operational-amplifier class, then to amplifier ICs, analog ICs, and ultimately the wider integrated-circuit and semiconductor categories. The LM358AWPT is identified by STMicroelectronics as a low-power dual operational amplifier. Its two-circuit configuration reduces component count and board area when two related analog functions must be implemented. The 8-pin TSSOP package supports automated assembly while preserving a compact outline. The listed 40 mA output-current capability also makes the device relevant to designs that require more drive than a minimum-footprint micropower amplifier. Each amplifier section can support common analog signal-processing tasks such as voltage amplification, impedance buffering, comparators, current-sensing interfaces, and active-feedback control. Because the two channels share package-level power pins, their operating supply is common even when they perform unrelated functions. PCB designers should still route input, output, supply, and ground connections carefully to minimize coupling between the two channels and to preserve signal integrity near the device. Typical applications include industrial sensor interfaces, low-voltage control loops, audio and communications equipment, battery-powered instrumentation, and general-purpose analog signal conditioning. In a feedback controller, one channel might amplify a sensor signal while the other buffers a reference or drives an error amplifier. In a sensing circuit, the dual organization can reduce the number of packages needed compared with separate single-channel amplifiers. The principal design consideration is supply compatibility. Confirm the minimum and maximum operating voltages, input common-mode range, output swing, input bias current, noise, slew rate, and stability requirements in the STMicroelectronics manufacturer datasheet before using the device with a selected system rail. Decoupling capacitors, grounding, output-load limits, and any reactive load compensation should follow the application guidance in that datasheet. This product page organizes the LM358AWPT information around verified product identity, package details, directly compatible replacement options, application guidance, and PCB-level design considerations. It also distinguishes exact drop-in candidates from broader LM358 comparisons so that engineers can assess footprint, function, and operating-limit compatibility before authorizing a substitution.
LM358AWST - Dual Low-Power Op Amp | STMicroelectronics
The STMicroelectronics LM358AWST is a dual, general-purpose operational amplifier with two amplifier circuits in an 8-pin MiniSO package. The device is identified as a low-power op amp and is intended for general signal-conditioning applications. Its package dimensions, electrical limits, supply range, offset characteristics, and temperature ratings should be confirmed against the STMicroelectronics datasheet before final qualification. An operational amplifier is an active semiconductor device that amplifies the voltage difference between its inverting and non-inverting inputs. The LM358 family belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, comparators, and analog signal-chain ICs. Its dual architecture provides two amplifiers in one package, reducing board area while simplifying common power-supply and grounding arrangements. The LM358AWST is specifically identified as a standard, general-purpose amplifier with two circuits. That makes it useful for functions such as voltage buffering, current-to-voltage conversion, sensor conditioning, differential amplification, and basic active filtering. Because it contains two amplifier sections, one package can support two related analog channels or two stages of a larger signal-processing circuit. Its MiniSO-8 form factor supports compact surface-mount PCB construction while exposing two complete amplifier channels. The exposed package area of the MiniSO family also provides a thermal path to the PCB, although actual heat dissipation depends on copper area, adjacent components, ambient temperature, and output drive. Designers should preserve the manufacturer’s recommended pad and land-pattern dimensions rather than treating it as a generic SOIC footprint. Typical uses include industrial sensor interfaces, buffered control signals, low-frequency analog measurement paths, audio preamplifier stages, power-supply monitoring, and general-purpose gain stages. In each case, input common-mode range, output swing, unity-gain stability, noise, and supply requirements must be checked against the circuit’s operating conditions. The LM358AWST is especially relevant where two general-purpose channels are needed without allocating separate single amplifier packages. For a new layout, route input and output traces away from switching nodes and high-current return paths, connect decoupling capacitors close to the supply pins, and verify the complete analog signal range at worst-case supply voltage and temperature. If the PCB revision is fixed, use the pin-description table and land-pattern drawing in the manufacturer datasheet to confirm every connection before substitution or sourcing an equivalent.
LM358BAIDR - Dual 36V 1.2MHz Op Amp | Texas Instruments
Texas Instruments LM358BAIDR is a dual operational amplifier with a 36 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 mV offset voltage, housed in an 8-SOIC package. The device contains two independent general-purpose amplifiers, making it suitable for signal conditioning, sensing, and control circuits that operate from single or dual supplies. An operational amplifier is an analog signal-processing IC that amplifies the difference between its inverting and non-inverting inputs. The LM358 family belongs to the broader operational-amplifier, analog-amplifier, and semiconductor hierarchy. Unlike a single amplifier package, this dual-device version provides two amplifier channels in one component, reducing board area and simplifying designs that require paired gain, filtering, buffering, or comparison functions. The LM358BAIDR combines a maximum 36 V supply rating with a 1.2 MHz gain-bandwidth product. Its 2 mV offset voltage is suitable for many general-purpose applications where moderate DC accuracy is acceptable. The 8-SOIC surface-mount package supports conventional PCB assembly, while the -40°C to 85°C operating range covers industrial and commercial environments. Typical rail-to-rail behavior, common-mode limits, supply-current requirements, and output-drive capability should be checked against the manufacturer datasheet for each design. The two amplifier sections share the power-supply pins but otherwise provide separate inverting and non-inverting inputs and outputs. This arrangement suits cascaded stages, dual sensor channels, error amplifiers, voltage followers, and differential signal-conditioning circuits. Because both channels use the same device, their offset, bandwidth, noise, and common-mode performance are inherently well matched for many balanced systems. Typical uses include industrial sensor interfaces, buffered control outputs, low-frequency active filters, audio preamplification, power-supply monitoring, and general embedded signal conditioning. It can also support two independent channels in equipment where a quad amplifier would leave unnecessary circuitry. The 1.2 MHz bandwidth is most appropriate for low- and intermediate-frequency signals rather than wideband video or high-speed communications. When laying out the PCB, route sensitive input and feedback traces away from switching nodes and high-current paths. Place input-rejection and output-bypass capacitors close to their corresponding pins, verify common-mode and output-swing limits at the intended supply voltage, and maintain adequate copper area for thermal dissipation. Confirm the exact SOIC-8 land pattern and pin numbering against the manufacturer pin-description table. This product page combines the LM358BAIDR ordering information, manufacturer specifications, package details, price reference, pinout status, and technically filtered replacement guidance. It also adds application-oriented design notes and comparison criteria that help engineers determine whether the original device or a qualified drop-in alternative best fits a new board revision.
LM358BIDGKR - 36V 1.2MHz Dual Op Amp | Texas Instruments
Texas Instruments LM358BIDGKR is a dual operational amplifier in an 8-pin VSSOP package, built for general-purpose signal conditioning from single or dual power supplies. Its headline electrical ratings are a 36 V maximum supply voltage, 1.2 MHz gain-bandwidth product, and 3 mV maximum input offset voltage. The LM358B family combines two amplifiers in one package and supports input common-mode ranges that extend toward ground, making it useful in industrial, instrumentation, control, and sensor-interface circuits. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify the difference between two input voltages. The operational-amplifier category sits above instrumentation amplifiers and buffers in the broader analog-IC hierarchy, while the dual configuration places two independent amplifiers in one compact surface-mount package. LM358B devices are often selected when moderate bandwidth, wide supply-voltage operation, and input-stage tolerance are more important than low-noise precision performance. The LM358BIDGKR provides a 1.2 MHz gain-bandwidth product and a slew rate of 0.5 V/µs. These values support general-purpose closed-loop signal processing, including voltage buffers, cross-coupled amplifiers, differential stages, integrators, and active filtering. Its 3 V to 36 V operating supply range accommodates common industrial and laboratory supply levels. The manufacturer identifies 300 µV as the typical low offset voltage for the LM358B family, while distributor product information lists 3 mV offset voltage for this ordering code. Because each channel contains an input stage, output stage, and compensation network, LM358B behavior depends on supply voltage, load, output voltage, and common-mode input level. The 1.2 MHz gain-bandwidth product makes the device suitable for moderate-frequency closed-loop gains rather than precision or high-speed applications. Users should account for output-current limits and ensure that the amplifier is not used to source or sink current beyond its specified operating conditions. Typical uses include 0–10 V industrial sensor interfaces, audio preamplifier and mixing stages, active analog filters, motor and actuator control loops, low-frequency data acquisition, and general sensor conditioning. In a single-supply system, the input common-mode range extending to ground helps process signals centered near 0 V, provided the output swing and input limits are checked against the actual supply voltage. For PCB design, keep input and feedback traces short, route output signals away from high-impedance inputs, and provide stable bypass capacitance close to the supply pins. Check output drive into the intended load and leave adequate headroom for input and output swing. Decoupling placement and trace geometry can matter more than nominal amplifier bandwidth when working with long routes or high source impedances. This page combines manufacturer specifications, ordering information, pin-package details, qualified same-family alternatives, and application guidance for faster component selection and board-level planning. It also highlights the practical distinction between the LM358B family's typical offset voltage and the ordering-code maximum used for design margin.
LM358BIDR - Dual 36V 1.2MHz Op Amp | Texas Instruments
The Texas Instruments LM358BIDR is a dual general-purpose operational amplifier with two amplifier channels, a 36 V maximum supply rating, 1.2 MHz gain-bandwidth performance, and 3 mV output offset voltage. The device is offered in an 8-pin SOIC package, making it suitable for conventional surface-mount analog signal-conditioning boards. The LM358 name identifies an industry-standard dual-amplifier configuration commonly used for amplification, buffering, filtering, and voltage comparison. An operational amplifier is a high-gain analog building block that compares an input signal with a feedback network and drives its output toward the difference between those signals. The dual-amplifier hierarchy connects the LM358BIDR to operational amplifiers, analog amplifiers, linear amplifiers, and integrated circuits. Two independent channels in one package reduce board area while providing a common supply arrangement for industrial controls, instrumentation, sensor interfaces, and general-purpose embedded systems. Key characteristics include two amplifier circuits, a 36 V maximum supply voltage, a 1.2 MHz gain-bandwidth product, and a 3 mV offset voltage. The 8-SOIC format supports automated surface-mount assembly and standard 1.27 mm pitch PCB layouts. Because the part is intended for broad analog applications, its useful performance depends on the selected feedback network, supply voltage, output load, input common-mode range, and required accuracy. The LM358BIDR belongs to the LM358B family of industry-standard dual operational amplifiers. Its internally compensated architecture simplifies typical closed-loop amplifier and voltage-follower configurations. Designers should still verify input and output operating limits for the intended supply and signal ranges in the manufacturer datasheet, particularly when approaching the device's maximum rated supply voltage. Typical applications include sensor signal conditioning, transducer amplification, analog filtering, comparator-style control loops, current-voltage conversion, audio preamplification, and general industrial signal conditioning. The dual-channel arrangement is particularly useful when a board needs two related analog channels without requiring a quad-amplifier package or two separate single-channel devices. For PCB implementation, place input, output, feedback, and decoupling connections to minimize parasitic coupling and preserve signal integrity. Keep sensitive input traces away from high-current switching paths, use a local supply bypass capacitor, and route the ground return carefully to reduce offset and noise pickup. Confirm output-current capability and stability with the selected load before committing to the design. This page organizes the exact LM358BIDR identity, package information, sourcing fields, replacement considerations, and application guidance into a practical engineering reference. It also distinguishes verified target-part characteristics from comparison fields that require an individual manufacturer datasheet review before a board redesign is approved.
LM358BIPWR - Dual 36V 1.2MHz Op Amp | Texas Instruments
The Texas Instruments LM358BIPWR is a dual, general-purpose operational amplifier designed for a 3 V to 36 V supply range, with a unity-gain bandwidth of 1.2 MHz, an input offset voltage of 3 mV, and low quiescent current of 300 uA per channel. The device is packaged in an 8-pin TSSOP (PW) package and is specified for operation from -40 °C to +85 °C. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. It belongs to the amplifier hierarchy that includes differential amplifiers, instrumentation amplifiers, and the broader category of analog signal-chain ICs. The LM358B contains two independent, internally compensated amplifiers sharing common supply and ground pins, making it useful where two amplified signals must be handled in one compact package. The LM358B version provides several characteristics suited to industrial and general-purpose designs. Its 3 V to 36 V operating range allows operation from conventional 5 V and 12 V rails as well as higher industrial supply voltages. A 300 uA quiescent current per channel supports power-conscious instrumentation, while the 1.2 MHz unity-gain bandwidth provides useful response for audio, control, and low-frequency signal-conditioning applications. Its common-mode input voltage range includes ground, enabling direct sensing of signals near the lower supply rail. Internally, each channel combines high open-loop gain with frequency compensation, allowing the device to operate as a unity-gain stable buffer without an external compensation capacitor. The two amplifiers are independent, although they share the same supply pins. This arrangement permits simultaneous functions such as signal amplification and active filtering, or two channels of sensor conditioning, while keeping the component count and PCB area below that of separate single-channel amplifiers. Typical applications include low-level sensor signal conditioning, transducer amplification, active filters, audio preamplifier stages, motor and actuator control loops, and general industrial control systems. The 8-pin TSSOP package is particularly useful for compact analog boards where a dual amplifier is required but SOIC or larger packages would be unnecessary. When designing around the LM358BIPWR, maintain adequate input and output voltage headroom at the selected supply voltage, especially for output swings near either rail. Place input-referring components close to the amplifier pins, keep feedback traces short, and verify that the intended signal bandwidth remains well below the 1.2 MHz unity-gain limit. Decoupling capacitance should be selected according to the manufacturer's recommended application circuit and layout guidance. This page combines manufacturer specifications, distributor availability information, cross-reference results, application guidance, and practical design considerations. It is intended to help engineers evaluate the LM358BIPWR for industrial, instrumentation, audio, and embedded-control designs without relying solely on a catalog parameter table.
LM358BP - Dual Operational Amplifier | Texas Instruments
The Texas Instruments LM358BP is a dual operational amplifier in an 8-pin surface-mount package, combining two independent amplifiers for general-purpose analog signal conditioning. The LM358BP is associated with the LM358 family, a low-power dual op-amp solution designed for applications requiring wide supply-voltage range, high open-loop gain, and straightforward single-supply operation. The verified manufacturer information identifies the LM358 family as a dual operational amplifier offering low power consumption, high gain, and a wide voltage range, while the LM358B device is specified as a dual, 36-V, 1.2-MHz, 3-mV-offset operational amplifier with an operating-temperature range of -40°C to 85°C. An operational amplifier is an active semiconductor device that uses differential input voltage to control an output voltage. A dual operational amplifier contains two amplifier sections in one package, allowing designers to implement two signal-processing channels while reducing board area and component count. The LM358BP is therefore useful in sensor interfaces, transducer amplifiers, voltage comparators, current-monitoring circuits, audio preamplifier stages, and general feedback-control circuits. Its dual architecture can also simplify designs in which two independent amplifier functions are required at similar supply and performance levels. The LM358B family is described by Texas Instruments as a dual, 36-V operational amplifier with 1.2-MHz bandwidth and 3-mV maximum offset voltage. The LM358BP ordering code identifies the specific package and ordering variant of this family. The verified distributor listing describes the device as a standard or general-purpose amplifier with two circuits, and identifies the package as an 8-pin micro PBGA surface-mount package. Because the exact package dimensions, pin assignments, and full electrical limits are not included in the manufacturer result excerpts used for this page, individual electrical values should be confirmed against the manufacturer datasheet before final circuit release. The LM358 family is commonly associated with low-power operation, high gain, and a wide operating-voltage range. In practical designs, the amplifier can be used with single-supply systems where the input and output signals remain within the common-mode and output-swing limits. The LM358BP is appropriate where two channels are needed and where a simple, widely understood dual-op-amp architecture is preferable to a more specialized precision or high-speed amplifier. Typical applications include resistive sensor conditioning, buffered instrumentation inputs, low-frequency audio amplification, comparator functions, and general feedback amplifiers. The device can reduce board area by providing two amplifiers in one package, while the family-level supply range supports operation from conventional single-supply rails. Designers should still verify input common-mode range, output swing, output-current capability, noise, offset drift, and stability requirements against the complete LM358B datasheet. For PCB implementation, use the manufacturer land pattern for the LM358BP package rather than substituting a generic SOIC-8 footprint. Place input, output, and supply bypass capacitors close to the relevant pins, maintain a short return path for ground currents, and avoid routing sensitive input traces beside the output stage. This page combines manufacturer family information, distributor identification, drop-in alternatives, application guidance, and design considerations to support component selection and PCB planning.
LM358BPX - Dual 36V 1.2MHz Op Amp | Texas Instruments
The Texas Instruments LM358BPX is a dual, general-purpose operational amplifier with two independent channels, a 36 V maximum supply rating, a 1.2 MHz gain-bandwidth product, and an 8-ball VFBGA package. The device combines a 3 mV input-offset-voltage rating with a 0.5 V/us slew rate, making it suitable for low-to-moderate-speed analog signal conditioning, feedback-control loops, and general-purpose amplification. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. The LM358 belongs to the operational-amplifier hierarchy, which includes voltage-feedback amplifiers, signal-conditioning ICs, and analog front-end components. Its two independent channels permit simultaneous processing of related signals without requiring two separate single-channel packages. The principal LM358B-family characteristics include operation from a single supply or from split positive and negative supplies, a 1.2 MHz unity-gain bandwidth, a 0.5 V/us slew rate, and a 3 mV maximum input-offset voltage. According to the TI LM358B product page, the commercial-temperature family operates from -40°C to 85°C. These characteristics place the amplifier between precision low-noise amplifiers and high-speed operational amplifiers: it offers useful DC accuracy and common-mode flexibility without the bandwidth of a high-speed comparator or precision amplifier. Each channel includes one input stage, an output stage, and compensation circuitry. The two amplifiers are independent rather than internally linked, allowing the same package to implement independent gain stages, comparators, buffers, or transducers. The 0.5 V/us slew rate limits how quickly a large output transition can occur, while the 1.2 MHz gain-bandwidth product limits closed-loop bandwidth as feedback gain increases. A practical gain-bandwidth relationship of 1.2 MHz divided by noise gain gives a useful first estimate of usable bandwidth. Typical uses include temperature-sensor signal conditioning, audio preamplification, DC motor-current monitoring, industrial sensor interfaces, low-frequency active filters, and power-supply feedback. For sensor applications, the 3 mV offset specification is important because input-referred offset appears directly at the amplifier output after multiplication by the closed-loop noise gain. In AC-coupled audio paths, the slew rate and bandwidth determine whether large low-frequency signals can be reproduced without excessive distortion. PCB design should prioritize short input and feedback paths, a stable output connection, and careful bypassing of the positive supply. Because the LM358BPX uses a compact ball-grid package, the manufacturer land pattern and pin-description table should govern assembly and inspection. Decoupling capacitors should be placed close to the supply and ground balls, while analog input traces should be kept away from switching nodes and high-current return paths. This page combines the LM358B family electrical characteristics, LM358BPX package information, pin assignments, verified source links, and practical guidance for analog-board design. It also identifies the limits of direct substitution: many LM358 equivalents use DIP or SOIC packages rather than the LM358BPX 8-ball VFBGA footprint, so a functional match does not necessarily qualify as a PCB drop-in replacement.
LM358D - Dual 700kHz General Purpose Op Amp | Texas Instruments (Tape & Reel)
The LM358D is a dual operational amplifier from Texas Instruments in an 8-pin SOIC (D) surface-mount package. It operates from a single supply of 3V to 32V or dual supplies of ±1.5V to ±16V, with a gain bandwidth product of 700 kHz and a slew rate of 0.3 V/µs. This industry-standard, low-cost amplifier serves a vast range of general-purpose analog functions. An operational amplifier (op amp) is a high-gain differential-input, single-ended-output voltage amplifier and one of the most fundamental building blocks in analog electronics. General-purpose op amps like the LM358 prioritize versatility, low cost, and ease of use over precision or bandwidth. The LM358 is the dual version of the LM321 single amplifier and the two-amp counterpart of the quad LM324. Key features include a common-mode input voltage range that extends to ground, enabling direct sensing near ground in single-supply systems; low supply current of 0.7 mA typ, independent of supply voltage; internal frequency compensation for unity-gain stability; and short-circuit protected outputs. These characteristics suit battery-powered and cost-sensitive designs. Technically, the LM358 uses a bipolar process with a class-AB output stage that can drive loads as low as 2 kΩ with a large output swing. The commercial temperature grade is 0°C to +70°C. Input bias and offset currents are low, and the two internal amplifiers are well matched, sharing the same supply and bias circuitry. Typical applications include transducer amplifier front ends, DC gain blocks, active RC filters, voltage comparators and level shifters, power-supply feedback loops, and portable or industrial control electronics. The SOIC-8 package supports automated SMT assembly and reflow. Design considerations: decouple V+ to GND with a 0.1 µF ceramic capacitor close to pin 8, and respect output swing limits near the rails (output saturates roughly 1.5V below V+ at moderate loads). For higher bandwidth or lower noise, consider the pin-compatible TLV9152 or TL072. Pricing as of 2026-08-30 starts around $0.05 at volume from distributors such as LCSC.
LM358D-JF - Dual Op-Amp, 2 Circuit, SOIC-8 | Texas Instruments
The Texas Instruments LM358D-JF is an industry-standard dual operational amplifier integrating two independent, internally compensated op-amp circuits in a single 8-pin SOIC package. According to the TI LM358 family datasheet, the device operates from a single supply as low as 3 V (B and BA versions) with a wide supply range up to 36 V, draws approximately 300 uA per channel of quiescent current (B and BA versions), and delivers a unity-gain bandwidth of about 1.2 MHz on the enhanced B/BA versions, with the standard LM358 characterized at 700 kHz on a 30-V class supply. The common-mode input voltage range includes ground, enabling direct sensing of signals near 0 V without a negative rail. An operational amplifier is an analog voltage amplifier with differential inputs and a single-ended output, forming the foundational building block of the linear signal chain: op-amp -> amplifier IC -> analog front end -> mixed-signal system. Dual op-amps such as the LM358D-JF combine two such stages behind one supply pin, halving board area and supply routing complexity compared with two single amplifiers. Key features include ground-sensing inputs for single-supply operation, a wide supply range supporting both 5 V logic-level and up to 36 V industrial rails (B/BA versions), low 300 uA-per-channel quiescent drain (B/BA versions) for battery-powered designs, and internally compensated unity-gain stability. The maximum input offset voltage of 2 mV at 25 C (BA version) keeps DC accuracy adequate for non-critical gain stages. The architecture uses a classic bipolar process with internal frequency compensation, giving well-behaved, phase-margin-safe behavior in inverting, non-inverting, and unity-gain buffer configurations. Output stages sink and source small currents and pull down close to ground on single supplies, which is why the LM358 remains the default comparator-adjacent amplifier for cost-driven designs. Typical applications include transducer signal conditioning near ground, low-speed active filters, current-sense front ends in power supplies and chargers, and level-shifting stages in industrial sensor nodes. The SOIC-8 surface-mount footprint suits compact commercial PCBs. Design consideration: keep closed-loop gains moderate and load capacitance low; the modest bandwidth means these parts are intended for slow, robust analog functions rather than wideband signal paths. This page adds value beyond the manufacturer datasheet by consolidating pin-compatible alternatives, pricing-channel availability, and practical design notes in one place.
LM358DE4 - 700kHz Dual Op Amp, 16V | Texas Instruments
Texas Instruments LM358DE4 is a dual general-purpose operational amplifier IC with two independent amplifier channels, a 700 kHz gain-bandwidth product, and operation from a 16 V maximum supply, packaged in an 8-pin SOIC. The device is intended for general-purpose analog signal conditioning, buffering, current sensing, filtering, analog measurement, and precision-control applications. An operational amplifier, or op amp, is a high-gain differential amplifier that uses negative feedback to amplify the difference between two input voltages. The LM358 belongs to the broader hierarchy of operational amplifier, analog amplifier IC, and semiconductor. Its dual-channel architecture provides two amplifiers in one package, reducing board area when two related analog functions are required. Unlike precision rail-to-rail amplifiers, the LM358 uses bipolar transistor circuitry and is therefore especially familiar in supply-voltage-oriented industrial, instrumentation, and control designs. Key characteristics include two amplifier circuits, a 700 kHz gain-bandwidth product, and a 16 V maximum supply identified by the manufacturer-oriented product information. The 8-SOIC package uses eight terminals in a rectangular surface-mount gull-wing format. Its dual-channel organization is useful for signal conditioning, buffering, current sensing, analog measurement, filtering, and precision-control circuits where two amplifiers share the same supply and ground references. The 700 kHz gain-bandwidth product makes the LM358 suitable for general-purpose closed-loop amplifier stages operating at low-to-moderate signal frequencies. In a non-inverting configuration, closed-loop bandwidth depends on the selected feedback network rather than the open-loop gain-bandwidth product alone. The bipolar implementation also supports operation from a single positive supply, allowing input and output signals to be referenced toward ground in many industrial and embedded analog circuits. Typical applications include sensor-signal conditioning, transducer buffering, active filtering, low-side current sensing, analog control loops, and general measurement boards. Two channels can implement differential signal conditioning, active filters, comparator-style threshold conditioning with suitable feedback arrangements, or independent amplifier stages sharing the same supply. The SOIC package is also convenient for prototype boards and production assemblies that use conventional surface-mount footprints. Design attention should focus on input common-mode range, output swing, load capability, and stability with the selected feedback network. Decoupling capacitors should be placed close to the supply pins, and sensitive analog traces should be kept away from switching nodes. Because the device is not rail-to-rail at its inputs and outputs, verify signal levels against the operating supply before using it in low-voltage battery systems. This page organizes the LM358DE4 specifications, pin and package information, application guidance, and pin-compatible alternatives into one engineering-focused reference. It also provides practical selection criteria for comparing the standard LM358 family with alternate dual-amplifier implementations before committing a PCB footprint to production.
LM358DG - Dual 1 MHz Operational Amplifier | onsemi
The onsemi LM358DG is a dual general-purpose operational amplifier with two amplifier channels, 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, and a 3 V to 32 V operating supply range. The device is supplied in an 8-SOIC package and supports both single-supply and split-supply operation. Its common-mode input range extends to ground and VEE, making it suitable for signal conditioning, current monitoring, and general industrial-control circuits. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification and feedback to control gain accurately. The dual LM358 architecture provides two amplifiers in one package, reducing board area while offering independent input, output, and supply connections. The LM358 belongs to the operational-amplifier hierarchy, which also includes single and quad amplifier packages used in instrumentation, sensor interfaces, and power-management systems. Key characteristics include a 3 V to 32 V supply range, 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, and a common-mode rejection ratio listed at a minimum of 65 dB. Input offset voltage is listed as 7 mV. The common-mode input voltage range extends to ground or VEE, allowing the amplifier to process signals near the lower supply rail. Low power drain and single- or split-supply flexibility suit both portable and industrial equipment. The dual amplifier can be used in noninverting and inverting gain stages, voltage followers, comparators, differential amplifiers, current-to-voltage converters, and sensor-signal conditioning. Independent channels allow one package to implement two related analog functions while sharing the same supply pins. However, users should verify input/output swing limits, output-current capability, stability conditions, and absolute maximum ratings in the manufacturer datasheet for the exact operating point. For PCB design, place the bypass capacitor close to the supply pin and route each amplifier's feedback and input traces away from switching nodes and high-current paths. Because the common-mode range extends toward ground but not necessarily beyond the positive rail, input signals must remain inside the specified common-mode limits. Stable feedback-network layout and adequate output-load compatibility are essential for reliable closed-loop behavior. This product page combines verified manufacturer and distributor information, same-footprint replacement candidates, parameter comparisons, and practical implementation guidance. It is intended to help engineers identify whether the LM358DG's dual-channel, wide-supply, near-ground-input capability fits a design before consulting the full manufacturer datasheet.