بەرهەمەکان (3,200+)

LM358ST - Dual General-Purpose Op Amp | STMicroelectronics
LM358ST

LM358ST - Dual General-Purpose Op Amp | STMicroelectronics

STMicroelectronics LM358ST is a dual, general-purpose operational amplifier with two independent, internally frequency-compensated amplifiers, an 800 kHz gain-bandwidth product, and an 8-TSSOP package. The device operates from a single power supply over a wide voltage range and is also specified for operation at supply voltages up to ±16 V, corresponding to a total supply range of 32 V. An operational amplifier is an analog signal-conditioning IC that uses differential feedback to amplify the voltage difference between its inverting and non-inverting inputs. The LM358 belongs to the general-purpose operational-amplifier family, which sits within the broader amplifier IC and semiconductor hierarchy. Its two independent channels allow one package to provide separate amplification paths for sensors, control loops, audio stages, or general analog signal processing. The principal features of the LM358ST include two independent amplifier circuits, internally integrated frequency compensation, a common-mode input range that includes ground, and low-power operation from a single supply. The 800 kHz bandwidth supports general-purpose closed-loop signal paths without requiring an external compensation network. Its 8-pin TSSOP format provides a compact surface-mount option for mixed-signal boards with limited routing area. Each channel uses a differential input stage and an internally compensated voltage-feedback architecture. Because the channels are independent, one can amplify a sensor signal while the other performs filtering, comparison, level conversion, or feedback control. Common-mode operation near ground is particularly useful for circuits powered from a single positive rail, where input signals may remain close to 0 V. Designers should still verify input and output swing against the specific supply voltage used in the final circuit. Typical uses include low-side current sensing, sensor amplification, audio and communications interfaces, industrial control, and embedded instrumentation. In an STM32-based measurement system, the two channels can condition separate analog inputs before conversion by the microcontroller. The device can also implement active filters or comparators because its outputs can typically swing close to ground when operated from a positive single supply. For PCB design, place input resistors, feedback components, and bypass capacitors close to the relevant pins to reduce parasitic feedback and noise pickup. A local supply decoupling capacitor should be positioned near pin 8, with the ground return routed directly to pin 4. Check input common-mode voltage, output swing, stability with the intended feedback network, and channel thermal dissipation before committing the layout. This product page combines the exact LM358ST package and electrical identity with sourcing guidance, genuine drop-in options, pin assignments, and practical application notes. It is intended to help engineers compare footprint, function, supply range, bandwidth, and design constraints faster than a raw distributor listing while preserving manufacturer datasheet requirements for final qualification.

RFQ پەیوەندی
LM358TP/NOPB - Dual Op Amp, 32 V, 8-DSBGA | Texas Instruments
LM358TP/NOPB

LM358TP/NOPB - Dual Op Amp, 32 V, 8-DSBGA | Texas Instruments

The Texas Instruments LM358TP/NOPB is a dual general-purpose operational amplifier packaged in an 8-DSBGA package. It provides two amplifier channels, operates from single or dual supplies with a total input range up to 32 V, offers a 1 MHz gain-bandwidth product, and supports a 0°C to 70°C commercial temperature range. Its 85 dB open-loop gain and 2 mV typical input offset voltage suit cost-sensitive signal-conditioning, buffering, and control applications. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. Negative feedback causes the amplifier to operate as a closed-loop gain stage, while internal compensation makes many standard closed-loop configurations possible without external compensation components. The LM358 combines two such amplifier sections in one package, reducing board area compared with two separate single-amplifier devices. The principal characteristics include a 1 MHz gain-bandwidth product, approximately 85 dB open-loop gain, a typical input offset voltage of 2 mV, and input bias current values of approximately 45 nA to 50 nA. The device operates from 3 V to 32 V, supports positive and negative signal operation around ground, and has an input common-mode range extending from negative supply voltage to positive supply voltage minus approximately 1.5 V. These characteristics make it suitable for low- and medium-bandwidth analog systems. The LM358 architecture is designed for straightforward general-purpose analog use. Its two channels can operate independently, allowing simultaneous signal conditioning, voltage comparison, current-to-voltage conversion, or cross-coupled amplifier arrangements. Because the gain-bandwidth product is 1 MHz, closed-loop bandwidth decreases as the selected noise gain rises. Designers should account for this relationship when selecting resistor values, filtering bandwidth, and required settling time. Typical applications include current sensing in industrial control systems, sensor signal conditioning in instrumentation, audio and communication interface circuits, active filtering, comparator-style threshold detection, and low-voltage control systems. The 1.3 mm by 1.3 mm DSBGA package supports compact layouts, although its fine pitch requires capable assembly processes, careful solder-paste control, and adequate thermal and assembly design. For single-supply designs, place the unused amplifier input close to a defined common-mode potential rather than leaving it floating. Use the manufacturer's pin-description table when assigning tracks and provide local supply bypassing to limit supply-induced disturbance. Ensure the output current, input common-mode voltage, and total supply voltage remain within the ratings for the selected operating conditions. This product data combines the electrical characteristics, package details, comparison parameters, and practical design guidance needed to evaluate the LM358TP/NOPB. The same-package substitution search is intentionally conservative because conventional LM358 replacements commonly use different packages, making them unsuitable as literal drop-in replacements for this 8-DSBGA footprint.

RFQ پەیوەندی
LM358TPX/NOPB - 2-Channel 1MHz 32V Op Amp | Texas Instruments
LM358TPX/NOPB

LM358TPX/NOPB - 2-Channel 1MHz 32V Op Amp | Texas Instruments

Texas Instruments LM358TPX/NOPB is a two-channel, general-purpose operational amplifier with a 1 MHz gain-bandwidth product, 32 V maximum supply capability, and an 8-DSBGA package. Each channel is a high-gain, internally frequency-compensated amplifier designed for single-supply operation, with typical performance figures including 65 dB common-mode rejection, 0.1 V/us slew rate, approximately 500 uA supply current per amplifier, and 2 mV input offset voltage. An operational amplifier is a high-gain analog building block used to amplify, buffer, compare, or sum signals. The dual-amplifier configuration provides two independent channels in one package, reducing board area when a circuit needs two general-purpose amplifier functions. Internally frequency compensation makes the devices straightforward to use for stable closed-loop gains without external compensation components, while the wide supply-voltage range supports both low-voltage and higher-voltage industrial designs. The 1 MHz gain-bandwidth product is suitable for audio, control, sensing, and signal-conditioning circuits that do not require high-speed operation. A 65 dB common-mode rejection ratio helps reject equal-mode interference, and the 0.1 V/us slew rate defines useful large-signal bandwidth for moderate-frequency waveforms. The 500 uA supply current per amplifier supports low-power signal paths, while the 32 V maximum rating provides additional headroom in applications using higher supply rails. The LM358 family architecture supports operation from a single positive supply or a split supply. Because each amplifier is independent, one channel can perform one function while the other performs a separate function. The 2 mV typical input offset voltage is suitable for many cost-sensitive general-purpose designs, although precision measurement systems should account for offset, bias current, noise, and temperature drift in their error budget. Typical uses include microphone preamplification, sensor signal conditioning, battery-powered monitoring, current-loop interfaces, comparator-style threshold detection, and general DC signal amplification. The 8-DSBGA format is useful where PCB area is constrained, but its small land pattern requires careful assembly and adequate thermal design. The tape-and-reel ordering option also supports automated production handling. For reliable layout, place input, output, and supply connections to minimize parasitic resistance and capacitance. Keep sensitive input traces short, provide local supply bypassing, and verify the exposed-ball thermal path against the PCB copper area. Designers should also account for input common-mode limits and output-current limits; the amplifier does not operate as a rail-to-rail input or output device. This product page organizes the key electrical characteristics, package information, sourcing terms, replacement constraints, and engineering guidance for the LM358TPX/NOPB. It also distinguishes same-footprint alternatives from broader LM358-family devices whose packages or electrical operating limits require a different design review.

RFQ پەیوەندی
LM358WPT - Dual 5V 1.1MHz Op Amp | ROHM | TSSOP-8
LM358WPT

LM358WPT - Dual 5V 1.1MHz Op Amp | ROHM | TSSOP-8

The ROHM Semiconductor LM358WPT is a dual general-purpose operational amplifier with two independent, internally compensated amplifiers in an 8-pin TSSOP package. Rated for a nominal 5 V supply, it supports single-supply operation from 3 V to 36 V or split-supply operation up to plus or minus 16 V. Key characteristics include a 1.1 MHz gain-bandwidth product, approximately 800 kHz small-signal bandwidth, and a 0.3 V/us slew rate. An operational amplifier, or op amp, is an analog signal-processing IC that amplifies the difference between two input voltages while providing high open-loop gain, negative feedback support, and output-voltage drive. The LM358WPT belongs to the hierarchy dual operational amplifier -> general-purpose amplifier -> analog amplifier IC -> semiconductor. Its common-mode input range can extend toward the negative supply rail, making it useful in single-supply sensor, audio, and control circuits. The LM358WPT integrates two independent amplifiers, allowing one package to implement stereo audio channels, dual-axis sensing, active filtering, or two-stage signal conditioning. Each channel uses standard industry-style pin assignments for dual op amps: two inputs, one output, and shared positive and negative supply connections. Internal compensation removes the need for external frequency-compensation components in typical closed-loop designs. At a nominal 5 V supply, the device combines a usable gain-bandwidth product of 1.1 MHz with a 0.3 V/us slew rate. This bandwidth supports audio-frequency and general feedback-control applications rather than high-speed signal conditioning. The large operating-supply range also permits direct interfacing with higher-voltage industrial systems, subject to the input and output common-mode limits and the device's absolute maximum ratings. Typical uses include microphone preamplification, transducers with ground-referenced outputs, loop-control systems, transducers, and general-purpose amplification. Because the output can source and sink current within the supply limits, the part also serves as an output-buffer stage when the load is not too heavy. When designing a PCB around the LM358WPT, place bypass capacitors close to the supply pins and route sensitive input traces away from switching nodes. Keep the negative supply connection short because common-mode performance and output swing depend on a low-impedance ground reference. Check the full operating-temperature range and load-current limits in the manufacturer datasheet before using the amplifier in extended-temperature equipment. This page consolidates package details, supply-range information, pin assignments, drop-in replacement candidates, and application guidance into a practical engineering reference. It also organizes the main design trade-offs so that engineers can compare bandwidth, supply capability, and package reuse before committing a PCB footprint.

RFQ پەیوەندی
LM358YPT - Dual 1.1MHz Low-Power Op Amp | STMicroelectronics
LM358YPT

LM358YPT - Dual 1.1MHz Low-Power Op Amp | STMicroelectronics

The STMicroelectronics LM358YPT is a low-power dual operational amplifier packaged in an 8-pin TSSOP. It provides two independent amplifier channels, a 1.1 MHz gain-bandwidth product, and a maximum input offset voltage of 9 mV. The device is identified as a standard general-purpose amplifier and is listed as RoHS compliant. Its dual-channel architecture makes it suitable for signal conditioning, sensor amplification, filtering, and other low-frequency analog circuits that require two amplifiers in one package. An operational amplifier is an analog integrated circuit that amplifies the difference between its inverting and non-inverting inputs. The LM358 belongs to the broader operational amplifier and amplifier IC hierarchy, where it occupies a general-purpose, low-power position rather than a precision or high-speed niche. Two independent amplifiers can process separate signals or be connected together for differential, gain, filtering, or feedback configurations, reducing component count and simplifying dual-signal analog front ends. The principal operating characteristics include a 1.1 MHz gain-bandwidth product, a maximum offset voltage of 9 mV, two amplifier circuits, and an 8-TSSOP package. The low-power description makes the device relevant to battery-operated and low-voltage equipment, while its dual organization improves PCB utilization when both channels are required. RoHS compliance supports use in electronic assemblies whose material restrictions are part of the manufacturing process. As a general-purpose amplifier, the LM358YPT is designed for conventional closed-loop analog applications rather than demanding precision, high-speed, or high-accuracy measurement channels. Designers should use the manufacturer datasheet for the complete electrical limits, input common-mode range, output swing, supply-current limits, compensation details, and recommended operating conditions. Those characteristics determine whether the amplifier maintains useful output swing and linear operation at the selected supply voltage. Typical uses include conditioning resistive sensor signals, buffering higher-impedance circuit nodes, amplifying low-frequency communications signals, implementing active filters, and building dual-channel control or monitoring circuits. In each case, the 1.1 MHz bandwidth provides a practical ceiling for low-frequency gain and closed-loop response, while the offset specification must be considered when signal accuracy matters. A key design consideration is input and output stability around the selected supply rails. Place bypass capacitance near the supply pins, route feedback components to minimize parasitic coupling, and confirm that the required output voltage remains inside the operating limits. The compact TSSOP package also requires careful assembly practices because its lead pitch limits soldering access. This page combines the exact LM358YPT package and headline electrical characteristics with engineering-focused application guidance, drop-in comparison candidates, PCB considerations, and sourcing information. These details help engineers determine whether the device fits a general-purpose analog design before committing it to a production BOM.

RFQ پەیوەندی
LM359M - Dual 400 MHz Norton Amplifier | Texas Instruments
LM359M

LM359M - Dual 400 MHz Norton Amplifier | Texas Instruments

The Texas Instruments LM359M is a dual, high-speed, programmable current-mode Norton amplifier with two independent amplifier circuits, a 400 MHz gain-bandwidth product, and a 60 V/µs slew rate. The LM359M is supplied in a 14-SOIC package and is intended for applications requiring high-frequency operation, user-programmable gain, and flexible feedback arrangements. An operational amplifier is an active analog signal-conditioning device that amplifies the difference between two input voltages while using negative feedback to set closed-loop behavior. The LM359 uses a current-mode, or Norton, input architecture rather than the voltage-input architecture common in conventional voltage-feedback amplifiers. This topology can provide high speed and high gain-bandwidth performance when supported by suitable external current-setting and compensation networks. The LM359 family provides two amplifiers in one package, reducing component count in dual-channel signal paths. Its high gain-bandwidth product makes it useful in video, communications, instrumentation, and active-filter circuits where signal bandwidth matters. The user-programmable gain and frequency characteristics allow circuit designers to tailor amplifier behavior with external resistors and capacitors, although stability must be checked for each selected feedback network. The LM359M is a 14-SOIC device with two amplifier sections, separate supply pins, and exposed package leads for through-hole board assembly or compatible PCB land patterns. Because it is a current-mode amplifier, input bias current, feedback-current selection, compensation, and maximum output swing require attention during design. The 400 MHz gain-bandwidth product does not mean every closed-loop circuit will operate at 400 MHz; usable bandwidth depends on gain, noise, stability, loading, and the external network. Typical uses include wideband video signal conditioning, pulse shaping, communications interfaces, active filters, oscillators, and instrumentation. The device is also suitable for educational and laboratory designs where a programmable high-speed analog amplifier is useful. Designers should begin with the manufacturer LM359 datasheet and verify the recommended external components for the intended gain and frequency response. A key design consideration is that LM359M is not a universal replacement for every voltage-feedback operational amplifier. Feedback topology, input bias-current behavior, compensation, output drive, and supply requirements must be checked against the original circuit. Stable operation also requires careful PCB layout, short feedback paths, suitable bypassing, and controlled parasitic capacitance. This page combines verified manufacturer and distributor information, package and application context, practical design guidance, and clearly identified data gaps. It is intended to help engineers evaluate LM359M for high-speed dual-amplifier designs without confusing its current-mode architecture with conventional voltage-feedback amplifier families.

RFQ پەیوەندی
LM359M/NOPB - Dual 400MHz High-Speed Amplifier | TI
LM359M/NOPB

LM359M/NOPB - Dual 400MHz High-Speed Amplifier | TI

Texas Instruments LM359M/NOPB is a dual, high-speed, programmable current-mode Norton operational amplifier with a 400 MHz gain-bandwidth product, 60 V/µs slew rate, 8 µA input bias current, and 40 mA output current per channel, packaged in a 14-SOIC tube package. The part is designed for high-frequency signal-chain work where user-programmable operating characteristics and stable inverting operation are important. The LM359 is an operational amplifier, a voltage-feedback signal-conditioning building block that compares an input signal with a feedback network and produces an amplified output. Its current-mode architecture places emphasis on high-frequency performance rather than the conventional high-impedance voltage-mode input used by many general-purpose amplifiers. The LM359 family therefore belongs to the broader category of analog ICs, operational amplifiers, and high-speed active signal-conditioning devices. Key features include two amplifier circuits on one monolithic IC, a 400 MHz gain-bandwidth product, 60 V/µs slew rate, and programmable amplifier operating characteristics. Each channel is broadbanded for high-frequency use, and the manufacturer identifies stable operation for inverting closed-loop gains of 10 or greater. The verified source data also lists 8 µA input bias current and 40 mA output current per channel, making the device suitable for analog signal conditioning, pulse processing, communications, and general-purpose amplification. The LM359M/NOPB ordering suffix identifies a specific Texas Instruments package and delivery configuration. The verified distributor data identifies the device as a dual general-purpose amplifier in a 14-SOIC case, while the target MPN is supplied in tube packaging. The NOPB designation is retained exactly as requested; package, temperature, and qualification details not explicitly present in the supplied data are marked as needed rather than inferred. Typical applications include high-frequency analog signal conditioning, communications interfaces, waveform shaping, pulse amplification, active filtering, and industrial or consumer control systems. Designers should preserve the recommended feedback and gain configuration, provide adequate bypassing, and verify stability experimentally because the current-mode Norton architecture and its programmable characteristics are not interchangeable with ordinary voltage-mode amplifier layouts without validation. For a new design, first confirm the required gain, bandwidth, output loading, supply arrangement, and package footprint against the manufacturer datasheet. Keep high-speed feedback traces short, place compensation and bypass components close to the relevant pins, and compare measured gain, phase margin, output swing, and slew behavior in the final board environment. This page synthesizes the verified manufacturer and distributor information with practical design guidance rather than claiming an unpublished full electrical table. Because the supplied web results do not include complete verified pin assignments, electrical limits, compliance declarations, or a reliable set of pin-compatible substitutes, those fields remain explicitly identified as data-needed. The most defensible purchasing and replacement decision requires checking the current Texas Instruments datasheet and distributor cross-reference results before production release.

RFQ پەیوەندی
LM359MX - Dual 60V/us High-Speed Amplifier | Texas Instruments
LM359MX

LM359MX - Dual 60V/us High-Speed Amplifier | Texas Instruments

The Texas Instruments LM359MX is a dual, high-speed, programmable current-mode Norton amplifier with a 60 V/us slew rate, supplied in a 14-SOIC package. Each channel provides independent input-offset balancing, gain programming, frequency compensation, and output saturation control. The verified listing identifies two general-purpose amplifier circuits in one package, making LM359MX suitable for analog signal conditioning, waveform shaping, and programmable-gain systems. A current-mode amplifier, commonly called a Norton amplifier, senses input current rather than directly measuring input voltage. LM359MX uses that architecture to achieve high bandwidth and fast slew performance while allowing gain and compensation to be programmed with external components. Each amplifier can therefore adapt its dynamic behavior to a particular signal bandwidth, gain, or output-drive requirement rather than operating only with fixed internal settings. The two independent channels support simultaneous analog processing or separate signal paths. Programmable operating characteristics are useful when one circuit must amplify small instrumentation signals and another must process faster pulses. The 60 V/us slew rate helps preserve large-signal waveform fidelity, while the dual configuration can reduce component count where two compatible amplifier functions are needed. Typical uses include pulse and transient amplifiers, analog summing stages, video or communications interface signal conditioning, laboratory interfaces, and wideband control loops. Because operating characteristics are programmable, the external network around each channel is as important as the nominal device specifications. Feedback components, compensation values, source impedance, and output loading must be selected together to maintain intended bandwidth and stability. For PCB layout, use a grounded return path near each amplifier, keep sensitive input and feedback traces short, and place compensation components close to their associated pins. The tape-and-reel ordering suffix MX identifies the verified LM359MX package configuration, while the functional LM359 family documentation describes the shared dual current-differencing architecture and programmable operating behavior. This page combines the verified manufacturer and distributor listing data with engineering guidance for the LM359MX. It also makes missing electrical limits and availability values explicit rather than inferring them, allowing designers to evaluate the device against the full LM359 datasheet and current authorized-distributor inventory before releasing a design.

RFQ پەیوەندی
LM359MX/NOPB - Dual 400MHz Norton Amplifier | Texas Instruments
LM359MX/NOPB

LM359MX/NOPB - Dual 400MHz Norton Amplifier | Texas Instruments

Texas Instruments LM359MX/NOPB is a dual, high-speed, programmable current-mode Norton amplifier IC with 400 MHz gain-bandwidth product, 60 V/µs slew rate, and two amplifier circuits in a 14-pin SOIC (D) package. According to the manufacturer product page and the LM359 data sheet, the device operates from a 5 V to 22 V supply, supports an operating temperature range of 0 °C to 70 °C for this ordering variant, and is intended for high-frequency signal conditioning, video, communications, and pulse applications. The LM359 uses current-differencing input stages rather than conventional voltage-input op-amp inputs, allowing the user to program amplifier operating characteristics with external components. Each amplifier is broadbanded for high gain-bandwidth product and fast slew rate, while stable operation is emphasized for inverting closed-loop gains of 10 or more. The two independent channels make the part suitable for dual-ended signal paths, differential interfaces, gain blocks, and active filtering. LM359MX/NOPB is supplied in tape-and-reel packaging with the manufacturer suffix MX. The component is a general-purpose precision analog building block rather than a digital or power-management device. Its 14-pin SOIC package supports conventional surface-mount assembly, but high-frequency layouts should minimize parasitic capacitance, provide adequate ground-plane continuity, and keep feedback components close to the relevant amplifier pins. Because the LM359 is a Norton-style amplifier, input bias current, input offset current, and feedback-network design materially affect accuracy. Engineers should use the manufacturer data sheet for the complete pinout, common-mode limits, output swing, input-current equations, and recommended application circuits.

RFQ پەیوەندی
LM359N/NOPB - Dual 400MHz Norton Op-Amp, 14-DIP | Texas Instruments
LM359N/NOPB

LM359N/NOPB - Dual 400MHz Norton Op-Amp, 14-DIP | Texas Instruments

The Texas Instruments LM359N/NOPB is a dual, high-speed, programmable, current-mode (Norton) amplifier integrated circuit housed in a 14-pin PDIP through-hole package. Each of the two independent amplifiers delivers a 400 MHz gain bandwidth product and a 60 V/µs slew rate, while providing user-programmable operating current and bandwidth through external resistors. The device operates from standard ±5V to ±15V (or single-supply 10V to 30V) supplies and is specified across the commercial 0 °C to +70 °C temperature range, making it suitable for cost-sensitive broadband and high-frequency signal-conditioning applications. A Norton (current-differencing) amplifier is a class of operational amplifier whose inverting input senses current rather than voltage, derived from classic current-differencing telemetry circuits. In the broader signal-chain hierarchy, Norton amplifiers belong to the linear IC family, sit alongside conventional voltage-feedback op-amps, and are commonly used as front-end gain blocks, video buffers, oscillators, comparators, and high-frequency AC amplifiers where standard op-amps lack sufficient speed. The LM359N/NOPB's two independent channels let one IC implement a complete two-stage function such as cascaded video gain or quadrature oscillator channels. Key features include a 400 MHz gain-bandwidth product, 60 V/µs slew rate, two independent Norton input stages, externally programmable quiescent current and bandwidth, and stable operation at closed-loop inverting gains of 10 or greater. Each amplifier can be biased to trade bandwidth against supply current, allowing designers to optimize power consumption for the target signal frequency. The 14-PDIP through-hole footprint simplifies prototyping, breadboarding, and legacy repair work on industrial control cards. The LM359 architecture pairs a current differencing input with a high-gain voltage output stage, yielding good high-frequency response that approaches that of much more expensive RF amplifiers. Because each amplifier's operating current is set by a single external resistor, the same device can serve as a 400 MHz wideband buffer or be reconfigured as a lower-power 50 MHz block by simply increasing the programming resistor. This flexibility is a key reason the part remains popular in instrumentation, video, RF, and oscillator designs decades after introduction. Typical applications include video and pulse amplifiers, RF and IF signal conditioning, wideband oscillators, current-mode comparators, and high-speed integrators. The two-amplifier configuration also suits active filter designs and instrumentation front ends that need matched channels. Designers retrofitting older equipment will find the DIP package convenient when working with through-hole production lines and replacement sockets. When designing with the LM359N/NOPB, program each amplifier's bandwidth and supply current through the I_set pin to balance power dissipation against required slew rate. A small ceramic bypass capacitor close to the supply pins is recommended to maintain high-frequency PSRR, and PCB traces to the inverting input should be kept short to minimize stray capacitance that could destabilize the high-gain stages.

RFQ پەیوەندی
LM3886TF - 68W Mono Class-AB Audio Amplifier w/ Mute | Texas Instruments
LM3886TF

LM3886TF - 68W Mono Class-AB Audio Amplifier w/ Mute | Texas Instruments

The Texas Instruments LM3886TF is a high-performance 68W continuous-average mono audio power amplifier with mute, housed in an 11-pin TO-220-11 Isolated (KC) through-hole package with an isolated tab. Operating from a single supply of 20V to 94V (or split ±10V to ±47V), the LM3886TF delivers 68W into 4Ω and 38W into 8Ω at 0.1% THD+N across the 20Hz–20kHz audio band, while the Class-AB topology preserves the low crossover distortion audiophile-grade designers expect from the Overture series. The device also includes a dedicated mute pin, SPiKe protection (short-circuit, thermal, over-voltage, under-voltage), and self-peak instantaneous temperature (°C) limiting. A Class-AB audio power amplifier is a linear amplifier topology that biases the output stage with a small quiescent current so both transistors conduct at the zero-crossing point, eliminating the crossover distortion of pure Class-B designs while still achieving high efficiency. Within the broader signal-chain taxonomy, the LM3886TF sits as a power-output stage downstream of a pre-amplifier and DAC/ADC, and belongs to the audio amplifier IC family, itself a sub-category of amplifier ICs (signal conditioning > amplifiers > audio amplifiers > power amplifier ICs). The Overture — LM3886 — series is TI's flagship monolithic hi-fi amplifier line. Key features of the LM3886TF include 0.1% THD+N at full output, 92dB minimum signal-to-noise ratio, 4Ω to 8Ω stable load drive, internal gain of 26dB (user adjustable with two external resistors), and a wide 20V–C to +85C excursion for the mute pin. The TO-220-11 isolated package provides 170°C/W maximum power dissipation. The Overture series signal-to-noise ratio minimum is a key differentiator over competing monolithic audio ICs. Typical applications include high-power mono subwoofer amplifiers, studio reference monitors, professional PA amplifiers, guitar combo amplifiers, and integrated stereo amplifiers (one LM3886TF per channel). The mute control pin allows use with a microcontroller or DSP interface to enable sequential power-up and standby control. When designing with the LM3886TF, ensure adequate heat-sinking—the isolated tab simplifies mounting on a chassis-coupled heat sink without requiring an insulating thermal pad (though one is optional). Use a low-impedance ground return, place the input RC network close to the pins, and observe the 94V absolute-maximum supply to avoid SPiKe protection tripping. The mute pin must be either driven high (>90%) or pulled low (<10% static) for proper operation—do not leave it floating or noise above 90 dB SNR will be compromised.

RFQ پەیوەندی
LM3886TF/NOPB - 68W Class-AB Audio Power Amplifier | TI
LM3886TF/NOPB

LM3886TF/NOPB - 68W Class-AB Audio Power Amplifier | TI

The Texas Instruments LM3886TF/NOPB is a high-performance 68W mono Class-AB audio power amplifier with mute, housed in an 11-pin TO-220 (NDA) isolated package. The device delivers 68W continuous average power into a 4 ohm load and 38W into 8 ohm with 0.1% THD+N across the 20 Hz to 20 kHz audio band, from a single supply of 20V to 94V. The TF suffix denotes a fully-isolated TO-220 leadform, while the NOPB suffix indicates lead-free / RoHS compliance. An audio power amplifier is the final analog stage that converts a low-level line-level input into a high-current, low-impedance signal capable of driving a loudspeaker. Class-AB topology blends the low conduction losses of Class-B with the low crossover distortion of Class-A, giving a compromise of efficiency and linearity that has dominated hi-fi amplifier design for decades. The LM3886 sits in the broader power management and amplifier IC hierarchy: audio amplifier -> Class-AB amplifier -> linear power amplifier -> analog output stage. Its self-peak instantaneous temperature (SPiKe) protection is a hallmark of the Overture series. Key specifications include 92 dB minimum open-loop gain, 0.03% typical THD+N at 1 kHz into 4 ohm, a slew rate of 19 V/us typical, and an operating temperature range of 0C to +70C. The mute function is logic-level controlled and the device includes internal current limiting and thermal shutdown. The fully-isolated TO-220 package permits direct mounting to a heatsink without an additional insulator pad, simplifying mechanical assembly. The bipolar output stage uses TI's SPiKe protection circuit, which provides dynamic, cycle-by-cycle current limiting as well as thermal shutdown. This yields a robust amplifier that tolerates output short circuits, reactive loads, and thermal overloads without destructive failure, making the LM3886 a long-standing favorite in DIY audiophile, subwoofer, and powered-monitor designs. Typical applications include powered subwoofers, home-theater amplifiers, professional powered monitors, guitar amplifiers, and high-fidelity integrated stereo amplifiers. The wide 20-94V supply range also makes it suitable for automotive 12V/24V bus and industrial audio systems when paired with a suitable boost converter. When designing with the LM3886, use a substantial heatsink rated for at least 40W continuous dissipation. Place the mute pull-down and 100k input resistors close to the IN+ pin to minimize noise pickup, and use 0.1 uF / 100 nF supply bypass capacitors within 1 cm of the V+ and V- pins. This page synthesizes distributor pricing, drop-in alternatives such as the LM3886T/NOPB and LM2876TF, and practical thermal design notes not found in the manufacturer datasheet itself, giving the engineer a single-page reference for sourcing and design.

RFQ پەیوەندی
LM393AD - Dual Open-Collector Comparator | Texas Instruments
LM393AD

LM393AD - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM393AD is a dual differential comparator with two independent comparison channels, open-collector outputs, and an 8-pin SOIC package. According to the verified manufacturer and distributor listings, the device is intended for commercial-grade applications, supports a common-mode input voltage range that includes ground, and has a differential input voltage range equal to the maximum-rated supply voltage of plus or minus 38 V. Its open-collector outputs are compatible with TTL, MOS, and CMOS logic. The LM393 family provides a straightforward way to compare an analog input against a reference voltage without requiring a pull-up resistor internally. This architecture is especially useful in threshold detection, signal conditioning, industrial control, sensing, and power-supply monitoring systems. A comparator is an analog integrated circuit that determines whether an input voltage is above or below a reference level and then represents that decision through a logic output. In the product hierarchy, the LM393AD is a dual comparator, which is a type of analog comparator and therefore part of the broader comparator IC and interface IC categories. Unlike an operational amplifier configured as a comparator, this dedicated device provides predictable switching behavior for applications in which the input frequently crosses a threshold. Two channels in one package can monitor two signals or implement complementary decisions while reducing board area. The most important verified features are the dual-channel configuration, open-collector output topology, and wide differential input capability. Each output can sink current and requires an external pull-up resistor when a valid high output level is required. The listed compatibility with TTL, MOS, and CMOS outputs allows the device to interface with multiple logic families. Because the common-mode input range includes ground, the LM393AD is suitable for circuits whose signal or reference is near 0 V. The manufacturer identifies the family as a commercial-grade dual differential comparator, and the verified technical listing specifies an 8-SOIC package. Electrically, the LM393AD compares two input voltages at each channel and controls an open-collector output transistor. The output remains high impedance when the transistor is off, so the external pull-up network determines the high voltage. This architecture supports wired logic, relay drivers, lamp drivers, and level translation, provided that pull-up current and output sink current remain within the device limits. The maximum differential input voltage is stated as plus or minus 38 V, but that value is not a substitute for the specified operating supply range. Supply voltage, input offset voltage, response time, output sink current, and electrical limits must therefore be confirmed from the manufacturer datasheet before final design release. Typical applications include industrial sensor thresholds, battery and power-supply monitoring, overvoltage detection, temperature-control signals, window comparators, and logic interfaces requiring an open-collector output. The dual configuration is useful when two independently adjustable thresholds must be evaluated, such as upper and lower battery limits. In a two-threshold system, one channel can detect overvoltage while the other detects undervoltage, allowing a system controller to distinguish safe, low, and high operating states. A key design consideration is the external pull-up resistor. Its value determines output rise time, bus speed, and the current required when the output transistor is off. The pull-up should connect only to a voltage that the output and downstream logic can tolerate. The input network must also prevent either differential input from exceeding the plus or minus 38 V differential limit. Designers should verify the exact SOIC-8 pin mapping, supply range, common-mode limits, and output-current limits in the manufacturer datasheet before assembly because those details were not present in the supplied verified excerpts. This page consolidates the verified manufacturer and distributor information for the LM393AD, distinguishes its defining dual open-collector characteristics, documents the evidence gaps without inventing missing values, and identifies the verified STMicroelectronics drop-in alternative. It also adds practical design guidance for pull-up selection, threshold implementation, and cross-brand sourcing.

RFQ پەیوەندی
LM393ADE4 - Dual 36V Open-Collector Comparator | TI
LM393ADE4

LM393ADE4 - Dual 36V Open-Collector Comparator | TI

The Texas Instruments LM393ADE4 is a dual, general-purpose voltage comparator with an open-collector output, operating from a single 2 V to 36 V supply or from dual supplies whose total span is within 2 V to 36 V. Each channel provides a common-mode input range that includes ground, and the open-collector outputs support wired-AND operation while remaining compatible with TTL, MOS, and CMOS logic. The device is packaged in an 8-SOIC. A comparator is an analog integrated circuit that evaluates two input voltages and switches its output according to their relationship. A general-purpose comparator belongs to the broader amplifier and comparator IC category, where it sits between simple logic gates and precision signal-conditioning channels. Unlike an operational amplifier, a comparator is designed for fast, saturated output transitions rather than linear amplification, making it suitable for threshold detection, level translation, and monitoring. The LM393 family provides two independent comparators in one 8-SOIC package. Its principal features include a 2 V to 36 V supply range, operation with a common-mode input range including ground, and open-collector outputs. These characteristics allow the device to monitor slow analog signals, supervise supply rails, interface to open-drain buses, or implement simple window-detection circuits using external resistor networks. Both comparator channels share the supply pins but otherwise operate independently. Their inputs can accept voltages extending below the positive supply rail, provided the differential input voltage remains within the rated supply span. Because each output is open collector, the output requires an external pull-up resistor, normally connected to the supply used by the receiving logic. Several comparator outputs can share one pull-up when wired-AND behavior is acceptable. Typical uses include industrial control and monitoring, overvoltage and undervoltage detection, temperature-condition signaling, battery threshold checking, and sensing interfaces that must operate from higher-voltage rails than ordinary 5 V CMOS logic. The wide supply range also allows the LM393ADE4 to operate from an 18 V industrial rail while its pull-up keeps the logic interface at a separate, lower voltage. When laying out the circuit, connect input sources so that absolute maximum differential and common-mode limits are respected, and place the output pull-up resistor close to the device or logic receiver. Avoid using the open-collector output to source current directly; the pull-up must provide the load current. Also verify compatibility between the unused output and its pull-up node before combining multiple channels. This page consolidates supply, package, pinout, drop-in comparison, and application guidance for engineers evaluating the LM393ADE4. It also highlights the practical differences among same-family and cross-brand SOIC-8 replacements, including where supply range, input common-mode limits, and output structure differ.

RFQ پەیوەندی
LM393ADG4 - Dual Open-Collector Comparator, 2V-36V, 8-SOIC | Texas Instruments
LM393ADG4

LM393ADG4 - Dual Open-Collector Comparator, 2V-36V, 8-SOIC | Texas Instruments

The Texas Instruments LM393ADG4 is a dual differential comparator IC with two independent open-collector outputs, a 2 V to 36 V single-supply operating range (±1 V to ±18 V on split supplies), and a 0.3 µs response time, packaged in an 8-pin SOIC (0.154 in, 3.90 mm width). Each channel offers rail-to-rail input common-mode range that includes ground, and the outputs are compatible with TTL, CMOS, and MOS logic. A comparator is a differential analog input IC that reports whether one input voltage is above or below a reference voltage, producing a logic-level output rather than an analog amplified signal. Within the wider hierarchy, a comparator sits between simple logic gates and operational amplifiers: it belongs to the analog signal-chain family of integrated circuits, alongside amplifiers and voltage references, and is normally used inside the power-management and sensing portion of a system rather than in the digital datapath. Key features of the LM393ADG4 include two independent channels in one 8-SOIC package, an open-collector (open-drain) output stage that requires an external pull-up resistor, single-supply or dual-supply operation, and input common-mode operation down to ground so the device can monitor low-voltage signals referenced to 0 V without a negative rail. Because the output is open-collector, the output high level is set by the pull-up and the supply rail, which allows the part to be level-shifted to any compatible logic voltage and allows several open-collector outputs to be wired together. Internally the LM393 family uses a classic bipolar differential input stage with an open-collector output driver, and the A-grade device is characterized for general-purpose supply and input conditions. The datasheet lists supply voltages tested at 30 V for non-V devices and 32 V for V-suffix devices, giving adequate margin above the nominal 36 V absolute maximum supply rating. Typical applications include window comparators for overvoltage and undervoltage protection, zero-cross and threshold detection for signal conditioning, relay or solenoid drive stages, sensor interface front ends for thermistors and light sensors, and battery monitoring in portable equipment. The open-collector output also makes the device suitable for driving indicator LEDs or optocouplers directly with a series current-limiting resistor. When designing with the LM393ADG4, remember that the open-collector output cannot source current: every output needs a pull-up resistor, typically between 1 kΩ and 10 kΩ, and the pull-up supply defines the logic high level. Keep the input common-mode voltage within the rated range and place the pull-up resistor close to the output to keep rise times short when driving capacitive loads.

RFQ پەیوەندی
LM393ADGKR - Dual 36V Comparator | Texas Instruments
LM393ADGKR

LM393ADGKR - Dual 36V Comparator | Texas Instruments

The Texas Instruments LM393ADGKR is a dual differential comparator with two independent channels, a 2 V to 36 V supply range, a 1.3 us response time, and open-collector outputs in an 8-pin VSSOP package. It compares two input voltages and provides a logic-level indication of which input is higher, making it suitable for threshold detection, supervision, and general-purpose signal conditioning. A differential comparator is an analog integrated circuit that evaluates the voltage difference between its inverting and non-inverting inputs. The LM393ADGKR belongs to the comparator and amplifier IC hierarchy within broader semiconductor and signal-conditioning applications. Its two channels operate independently, while a common supply and ground establish the operating reference for both comparators. Key characteristics include a 2 mV input offset voltage, 250 nA input bias current, a 1.3 us response time, and an open-collector output configuration. The common-mode input range includes ground, supporting interfaces where one signal approaches the lower supply rail. Open-collector outputs can sink useful current and require an external pull-up resistor, enabling wired logic, level translation, and flexible output rise-time control. The LM393ADGKR accepts single-supply operation across a broad voltage range, while dual-supply applications can use the available ±18 V operating range identified for this device. Because the output stage is open collector, the output voltage is set by the pull-up network rather than actively driven high. This architecture is efficient for alarm, relay-control, and interface circuits, but it also means the output cannot source current without suitable external circuitry. Typical applications include industrial threshold detection, battery and power-supply monitoring, sensor conditioning, window comparison, and open-drain logic interfacing. The dual-channel configuration reduces component count when two independent comparisons are needed. It is also appropriate for systems that intentionally require a pull-up-defined high level, such as wired interconnects, indicator drivers, and level-shifting arrangements. The principal design consideration is the open-collector output. Select a pull-up resistor that provides adequate sink current while keeping rise time within the system timing budget. Also verify input common-mode limits, supply sequencing, output leakage, and thermal conditions for the exact operating environment before finalizing the circuit. This page consolidates electrical characteristics, verified lifecycle and compliance information, pin-compatible replacement options, and practical design guidance for engineers evaluating the LM393ADGKR in industrial, monitoring, and general-purpose comparator circuits.

RFQ پەیوەندی
LM393ADGKRG4 - Dual Open-Collector Comparator | Texas Instruments
LM393ADGKRG4

LM393ADGKRG4 - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM393ADGKRG4 is a dual differential analog comparator with two independent general-purpose channels, a 2 V to 36 V single-supply operating range, and an 8-VSSOP package. Each comparator provides open-collector output for compatibility with wired logic, and the device supports single-supply or split-supply operation. Its rail-to-rail input common-mode range makes it suitable for general-purpose voltage-threshold, signal-conditioning, and industrial control tasks. An analog comparator is an interface IC that compares two input voltages and produces a logic-level indication of their relationship. The LM393 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Unlike a digital logic gate, the comparator evaluates continuously varying analog voltages, while its open-collector output provides a flexible interface to pull-up-based digital systems, relay drivers, and open-collector buses. The two LM393ADGKRG4 channels operate independently, allowing one device to implement two threshold functions. Its open-collector outputs can sink current from an external pull-up and can be left unconnected when unused. The broad 2 V to 36 V supply range supports low-voltage logic systems as well as higher-voltage industrial and instrumentation circuits, while the 8-VSSOP surface-mount package supports compact PCB layouts. Common-mode input behavior is an important architectural feature of the LM393 family. The manufacturer identifies the device as rail-to-rail, allowing the input voltages to approach the supply rails under supported operating conditions. The open-collector architecture is particularly useful when the output must drive a pull-up to a different voltage domain, participate in wired-AND logic, or control a downstream stage without an integrated push-pull output driver. Typical uses include battery-threshold detection, sensor signal conditioning, overvoltage and undervoltage supervision, window comparators, industrial control interfaces, and logic-level translation between voltage domains. Two independent channels can monitor a pair of limits, compare a sensor signal against a reference, or provide separate comparator functions with the same device. When designing the circuit, select an external pull-up resistor for each open-collector output and account for its maximum sink current, output voltage, and switching speed. Keep input and output paths away from high-current switching nodes, use a stable reference for precise thresholds, and verify the complete design against the manufacturer datasheet’s input common-mode, supply, output-current, and absolute-maximum-rating limits. This page consolidates the verified LM393ADGKRG4 package and supply information with pin-level implementation guidance, application examples, and same-package replacement comparisons. It helps engineers identify the correct footprint, understand the open-collector interface, and assess whether a candidate alternative preserves both the 8-VSSOP layout and the LM393’s core operating characteristics.

RFQ پەیوەندی
LM393ADR - Dual Open-Collector Comparator | Texas Instruments (Tape & Reel)
LM393ADR

LM393ADR - Dual Open-Collector Comparator | Texas Instruments (Tape & Reel)

The Texas Instruments LM393ADR is a dual differential comparator with two independent comparison channels, open-collector outputs, and an 8-pin SOIC package. According to the verified manufacturer and distributor listings, the device is intended for commercial-grade applications, supports a common-mode input voltage range that includes ground, and has a differential input voltage range equal to the maximum-rated supply voltage of plus or minus 38 V. Its open-collector outputs are compatible with TTL, MOS, and CMOS logic. The LM393 family provides a straightforward way to compare an analog input against a reference voltage without requiring a pull-up resistor internally. This architecture is especially useful in threshold detection, signal conditioning, industrial control, sensing, and power-supply monitoring systems. A comparator is an analog integrated circuit that determines whether an input voltage is above or below a reference level and then represents that decision through a logic output. In the product hierarchy, the LM393ADR is a dual comparator, which is a type of analog comparator and therefore part of the broader comparator IC and interface IC categories. Unlike an operational amplifier configured as a comparator, this dedicated device provides predictable switching behavior for applications in which the input frequently crosses a threshold. Two channels in one package can monitor two signals or implement complementary decisions while reducing board area. The most important verified features are the dual-channel configuration, open-collector output topology, and wide differential input capability. Each output can sink current and requires an external pull-up resistor when a valid high output level is required. The listed compatibility with TTL, MOS, and CMOS outputs allows the device to interface with multiple logic families. Because the common-mode input range includes ground, the LM393ADR is suitable for circuits whose signal or reference is near 0 V. The manufacturer identifies the family as a commercial-grade dual differential comparator, and the verified technical listing specifies an 8-SOIC package. Electrically, the LM393ADR compares two input voltages at each channel and controls an open-collector output transistor. The output remains high impedance when the transistor is off, so the external pull-up network determines the high voltage. This architecture supports wired logic, relay drivers, lamp drivers, and level translation, provided that pull-up current and output sink current remain within the device limits. The maximum differential input voltage is stated as plus or minus 38 V, but that value is not a substitute for the specified operating supply range. Supply voltage, input offset voltage, response time, output sink current, and electrical limits must therefore be confirmed from the manufacturer datasheet before final design release. Typical applications include industrial sensor thresholds, battery and power-supply monitoring, overvoltage detection, temperature-control signals, window comparators, and logic interfaces requiring an open-collector output. The dual configuration is useful when two independently adjustable thresholds must be evaluated, such as upper and lower battery limits. In a two-threshold system, one channel can detect overvoltage while the other detects undervoltage, allowing a system controller to distinguish safe, low, and high operating states. A key design consideration is the external pull-up resistor. Its value determines output rise time, bus speed, and the current required when the output transistor is off. The pull-up should connect only to a voltage that the output and downstream logic can tolerate. The input network must also prevent either differential input from exceeding the plus or minus 38 V differential limit. Designers should verify the exact SOIC-8 pin mapping, supply range, common-mode limits, and output-current limits in the manufacturer datasheet before assembly because those details were not present in the supplied verified excerpts. This page consolidates the verified manufacturer and distributor information for the LM393ADR, distinguishes its defining dual open-collector characteristics, documents the evidence gaps without inventing missing values, and identifies the verified STMicroelectronics drop-in alternative. It also adds practical design guidance for pull-up selection, threshold implementation, and cross-brand sourcing.

RFQ پەیوەندی
LM393ADRE4 - Dual 36V Open-Collector Comparator | Texas Instruments
LM393ADRE4

LM393ADRE4 - Dual 36V Open-Collector Comparator | Texas Instruments

The Texas Instruments LM393ADRE4 is a dual differential analog comparator with an open-collector output, a 300 ns response time, and operation from 2 V to 36 V, housed in an 8-pin SOIC package. It contains two independent comparator channels, and each channel supports rail-to-rail input comparison while driving external pull-up circuitry through an open-collector transistor. A comparator is an analog integrated circuit that evaluates two voltages and produces a digital logic state indicating which input is higher. The LM393A belongs to the broader comparator hierarchy within analog and mixed-signal semiconductors. Its open-collector architecture makes it particularly useful when a circuit needs a wired logic function, level translation, system reset, or an externally defined pull-up voltage rather than a fixed active push-pull output. The principal features of the LM393ADRE4 are its dual-channel configuration, wide 2 V to 36 V operating range, rail-to-rail input capability, and open-collector outputs. The 300 ns propagation delay makes it suitable for general-purpose threshold detection, signal conditioning, and monitoring functions. The 8-SOIC body is specified at 0.154 inch, or 3.90 mm, width, supporting conventional surface-mount PCB assembly and existing SOIC-8 layouts. Each channel compares a non-inverting input against an inverting input. The output transistor is pulled low when the non-inverting input is higher than the inverting input and releases to a high impedance when the opposite condition applies. Because the output is open collector, the output high voltage is not internally fixed; it is established by an external pull-up resistor and the available supply. This feature allows several open-collector outputs to share a bus, but it also requires correct pull-up selection and compatible system levels. Typical uses include overvoltage and undervoltage monitoring, battery threshold detection, sensor signal conditioning, window comparison, relay or LED drive, and general logic interfacing. The wide supply range is useful in industrial control systems where the comparator may operate from a rail substantially higher than a 5 V logic system. When dual supplies are used, the total supply difference must remain within the device operating limits. PCB implementation should follow the manufacturer pinout and place the comparator input and output tracks away from switching nodes and high-current paths. Keep the open-collector pull-up resistor close to the output node to limit rise time and susceptibility to capacitive coupling. Confirm input common-mode limits, output pull-up voltage, and logic-family compatibility before replacing a device in an existing design. This page consolidates the LM393ADRE4 ordering information, technical characteristics, replacement guidance, and application-focused design considerations into one engineering reference. It also distinguishes genuine same-footprint replacements from options that require package, voltage, or logic-architecture changes, helping designers select a compatible device without relying on package naming alone.

RFQ پەیوەندی
LM393ADT - Dual Open-Collector Comparator | STMicroelectronics
LM393ADT

LM393ADT - Dual Open-Collector Comparator | STMicroelectronics

STMicroelectronics LM393ADT is a low-power dual differential comparator containing two independent comparator channels in an 8-pin SOIC package. Each channel provides rail-to-rail input comparison and an open-collector output, making the device suitable for general-purpose signal thresholding, monitoring, and interface applications. The LM393ADT operates from a single supply and also supports split power supplies. A comparator is a semiconductor device that compares two input voltages and produces a logic-level result indicating which input is higher. The dual-comparator architecture places two independent channels in one package, reducing component count when a system performs two related threshold decisions. As a general-purpose comparator, the LM393ADT belongs to the broader voltage-comparison and signal-conditioning hierarchy rather than to an amplifier, converter, or regulator product class. The principal features of the LM393ADT are its two independent comparator channels, rail-to-rail input operation, open-collector outputs, and compatibility with both single and split power-supply arrangements. Open-collector outputs provide a useful pull-up interface for wired logic, level translation, and systems requiring an external pull-up resistor. Because the output transistor is exposed rather than driven by an internal totem-pole stage, circuit designers can select the pull-up voltage independently of the comparator supply in many applications. Internally, the two channels operate independently, allowing each comparator to monitor a different signal pair. This architecture supports two separate threshold decisions without shared input multiplexing. Rail-to-rail input behavior makes the input common-mode range an important design consideration, while the open-collector output requires an external pull-up in normal open-drain operation. The 8-SOIC package provides a conventional surface-mount footprint for PCB assembly and hand rework. Typical uses include industrial control and threshold detection, battery and power-supply monitoring, sensor signal conditioning, comparator-based oscillator circuits, window detection, and general logic interfacing. The part can also serve as the decision element in systems that convert an analog voltage into a digital state. Its dual-channel organization is particularly useful when two monitored quantities must produce separate logic outputs. When designing a board around the LM393ADT, reserve a pull-up resistor for each open-collector output and keep the pull-up voltage compatible with the receiving logic. Review input common-mode limits, output rise and fall behavior, supply decoupling, and the voltage relationship between input signals and supply rails. Account for input signals that can approach the supply rails when sizing protection or biasing networks. This page combines the verified LM393ADT product identity, package and functional characteristics with compatible comparator references and practical design guidance. It also organizes replacement, selection, sourcing, datasheet, and application questions into concise engineering answers for faster component evaluation.

RFQ پەیوەندی
LM393AM - Dual 36V Differential Comparator | onsemi | SOIC-8
LM393AM

LM393AM - Dual 36V Differential Comparator | onsemi | SOIC-8

The onsemi LM393AM is a dual differential comparator with open-collector outputs, designed for general-purpose signal comparison in an 8-pin SOIC package. It supports single-supply operation to 36 V and dual-supply operation to ±18 V. Each channel compares two input voltages and provides a low-voltage open-collector output suitable for pulling a logic node low. The device also offers low input bias current of 25 nA typical and low current drain of 800 µA typical. A differential comparator is an integrated circuit that evaluates the relationship between two voltages and translates the result into a logic-level output. The LM393 belongs to the comparator hierarchy within analog and mixed-signal semiconductors, where it sits alongside amplifiers, voltage references, logic interfaces, and other power-management functions. Its open-collector architecture is particularly useful when a designer needs to combine outputs, control a wired bus, or interface to legacy TTL and CMOS logic. The LM393AM provides two independent comparator channels in one package. Operation from a single supply allows the common-mode input range to approach ground, making the part useful for battery-powered monitoring, sensor conditioning, window comparison, and supply-control circuits. An open-collector output requires an external pull-up resistor because the output transistor actively pulls the output toward ground but does.source current from the output. This feature permits wired logic operation when several outputs share a bus and allows the output polarity to be changed by assigning the pull-up to either the positive or negative supply. The principal engineering trade-off is low power consumption versus modern performance. The 800 µA typical current drain suits battery-operated equipment, while the 25 nA typical input bias current helps preserve accuracy with high-impedance sensing networks. Because the output is open collector, designers must verify pull-up resistance, pull-up voltage, rise time, output sink current, and system-level timing rather than treating the part like a push-pull logic gate. Typical applications include overvoltage and undervoltage protection, battery monitoring, thermistor and light sensor interfaces, motor or actuator threshold detection, industrial control modules, and embedded logic. In each case, the LM393AM converts a small analog differential into a digital decision. The commercial-temperature LM393AM should be selected where its specified temperature range, supply limits, offset behavior, and propagation delay satisfy the design. For PCB implementation, place the decoupling capacitor close to the supply and ground pins, keep input traces short, and provide adequate copper for heat dissipation. The open-collector output node can be sensitive to capacitive loading and leakage, so external pull-up placement and grounding require careful review. This page combines verified source data, package-level alternatives, parameter comparisons, and application guidance to support practical component selection without relying on the datasheet alone.

RFQ پەیوەندی
LM393AN - Dual Comparator for 5V Control | STMicroelectronics
LM393AN

LM393AN - Dual Comparator for 5V Control | STMicroelectronics

The STMicroelectronics LM393AN is a dual, independent, general-purpose voltage comparator with open-collector outputs, packaged in an 8-DIP. It supports single-supply or split-supply operation and is intended for comparison tasks where a low-side, open-drain signaling output is useful. The verified source identifies the device as rail-to-rail and suitable for common-mode input ranges extending toward ground on a single supply. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input crosses the other. The LM393AN contains two independent comparator channels in one package. Within the broader semiconductor hierarchy, it is a comparator IC, an analog interface device, and part of the integrated-circuit family used for sensing, control, protection, and digital threshold conversion. The principal feature is its open-collector output architecture, allowing each channel to interface with pull-up resistors and external loads. This architecture is useful in open-drain buses, wired logic, relay-driver stages, and systems where multiple comparators can share a signaling line under suitable conditions. Because the supplied results do not provide complete numerical electrical tables, exact supply voltage, input offset, response time, and current limits require confirmation from the manufacturer datasheet. The LM393AN is a bipolar general-purpose comparator rather than a rail-to-rail input comparator in the modern CMOS sense, although the distributor listing describes the device as rail-to-rail. Its two channels are electrically independent, allowing one section to monitor a supply threshold while the other evaluates a signal or temperature-derived voltage. The open-collector outputs require external pull-up components when a logic-high output is required. Typical applications include industrial overvoltage and undervoltage monitoring, sensor threshold detection, battery and power-supply supervision, open-drain interface translation, and control systems comparing an analog input with an adjustable reference. For battery-powered designs, engineers should review the device's supply-current specifications because a classic general-purpose comparator may consume more current than a modern low-power equivalent. Designers should place the input and output components close to the package pins, use an appropriate pull-up resistor on each open-collector output, and verify the common-mode and supply limits for the selected manufacturer. Input polarity, output sinking current, and propagation delay must be checked before substituting another manufacturer's LM393AN or an LM393-family device. This page consolidates verified manufacturer and distributor information, identifies source-backed drop-in sourcing options, and adds engineering-focused comparison and application guidance. It is intended to support part selection while clearly separating confirmed package and architecture details from electrical parameters that require the manufacturer datasheet.

RFQ پەیوەندی
LM393AP - Dual 36V Open-Collector Comparator | Texas Instruments
LM393AP

LM393AP - Dual 36V Open-Collector Comparator | Texas Instruments

The Texas Instruments LM393AP is a dual differential comparator with two independent comparator channels, a 2 V to 36 V single-supply operating range, and a 300 ns response time in an 8-pin PDIP package. Each channel provides an open-collector output that can sink useful load current and operate at voltages up to 36 V. The device is intended for general-purpose commercial applications requiring threshold detection, signal conditioning, or simple analog decision-making. A differential comparator is an analog IC that compares two input voltages and changes its output state when the difference crosses a defined threshold. The LM393AP belongs to the comparator hierarchy, where a comparator is a specialized amplifier IC used for voltage-level detection rather than linear signal amplification. Its two independent channels allow one package to implement two separate sensing or control functions. Key characteristics include a wide 2 V to 36 V supply range, a differential input arrangement, an open-collector output, and a response time of 300 ns. The open-collector architecture requires an external pull-up resistor, but it provides useful flexibility because the output can be pulled to a system-defined voltage and the device can remain off during output high states. The input offset voltage can reach ±5 mV according to the published LM393 comparator information. The architecture is suited to low- and moderate-speed threshold decisions. Its propagation delay is long compared with a high-speed logic comparator, but it is appropriate for monitoring, sorting, control, and protection functions that do not require sub-microsecond response. The differential inputs support sensing above or below a reference voltage, while the two channels can share a supply but operate independently. Typical uses include battery monitoring, overvoltage detection, sensor signal conditioning, window comparison, temperature-control thresholds, and industrial control interfaces. In battery systems, the broad operating supply range allows the comparator to monitor divided supply voltages without requiring a low-voltage-only comparator. When designing a PCB around the LM393AP, place input and pull-up components close to the device and keep sensitive comparator inputs away from switching nodes. Because the output is open collector, never leave an output undefined; fit the appropriate pull-up resistor to a compatible logic or supply rail. Verify differential input limits, output current, and common-mode range against the application’s worst-case voltage conditions. This page combines device specifications, application guidance, same-package drop-in options, and a parameter-by-parameter comparison to support schematic review, PCB planning, and sourcing decisions.

RFQ پەیوەندی
LM393APG4 - Dual Open-Collector Comparator, 8-PDIP | Texas Instruments
LM393APG4

LM393APG4 - Dual Open-Collector Comparator, 8-PDIP | Texas Instruments

The Texas Instruments LM393APG4 is a dual differential comparator consisting of two independent voltage comparators in an 8-pin PDIP (0.300 inch, 7.62 mm) through-hole package with open-collector, open-emitter outputs and a common supply range of 2 V to 36 V. A comparator is a differential amplifier whose output switches state whenever the voltage applied to its inverting input rises above or falls below the voltage on its non-inverting input. As a product type, the LM393 family sits in the hierarchy comparator -> differential comparator -> analog signal conditioning IC -> integrated circuit, and it is one of the most widely cloned analog building blocks in the industry. Because the output stage is open collector, the output node can pull only to a logic-low rail, which makes the part directly usable with pull-up resistors to any supply between 2 V and 36 V, including 3.3 V, 5 V and 24 V system levels. Key features of the LM393APG4 include two independent comparator channels that can operate from a single supply or from split dual supplies, rail-to-rail input common-mode range as highlighted in distributor listings, and an open-collector output stage that supports wired-AND busing and level translation. The device is specified as a standard, general-purpose comparator, and the same die is offered in multiple package and temperature options under the LM393 and LM393A orderable part numbers. Architecturally, each channel in the LM393 uses a differential input pair feeding an open-collector output stage, so the outputs are naturally slow but noise-tolerant; the design is intended for sensing thresholds rather than for high-speed signal conditioning. Because the output transistor is not driven above the low state, a pull-up resistor is mandatory, and any change in pull-up supply changes the output high level without affecting the input stage. Typical applications include over-voltage and under-voltage protection in switching power supplies, window comparators for battery monitoring, temperature threshold detection with external sensors, zero-cross detection in AC line circuits, relay and solenoid drive, and general level translation between dissimilar logic families. Industrial control and instrumentation designs use the open-collector outputs to drive optocouplers, transistors, or LED indicators directly. When designing around the LM393APG4, always place the pull-up resistor as close as practical to the output pin to limit stray capacitance-induced switching spikes, and note that the two channels share a common ground and a common supply pin. Because the output is open collector, the device cannot source current; any load must be referenced to the same ground as the device. This page combines manufacturer specification details, package and pin-level guidance, drop-in replacement options, and practical design notes so that engineers can evaluate the LM393APG4 alongside modern low-power alternatives without re-reading multiple documents.

RFQ پەیوەندی