بەرهەمەکان (3,200+)

LT1007ACP - Low-Noise Precision Op Amp | Texas Instruments
LT1007ACP

LT1007ACP - Low-Noise Precision Op Amp | Texas Instruments

The Texas Instruments LT1007ACP is a low-noise, high-speed, precision operational amplifier with a typical differential voltage gain of 20 V/uV, a 60 MHz gain-bandwidth product for the decompensated LT1037 family, and an 8-pin PDIP package. The device is designed for instrumentation and signal-chain applications where low input noise, offset stability, and wide bandwidth are more important than a low quiescent current. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The LT1007 belongs to the precision operational-amplifier hierarchy, combining low-noise input stages, low input offset voltage, low temperature drift, and high common-mode and power-supply rejection. This makes it useful within measurement, instrumentation, audio, and precision analog systems. The LT1007 family provides maximum equivalent input noise voltage of 3.8 nV/sqrt(Hz) at 1 kHz and 4.5 nV/sqrt(Hz) at 10 Hz, with a typical low-frequency peak-to-peak equivalent input noise voltage of 60 nV from 10 Hz. Its typical input offset voltage is 10 uV, while its input voltage drift is 0.2 uV/degree C. Common-mode rejection and power-supply rejection are specified at 130 dB, supporting accurate amplification in circuits exposed to supply or common-mode disturbances. The amplifier is capable of high open-loop gain, with a typical differential voltage amplification of 20 V/uV at 25 degrees C while driving a 2 kOhm load to plus or minus 12 V. The family also supports high-speed operation, with a minimum slew rate of 11 V/us for the LT1037 and LT1037A versions. The combination of precision, low noise, and speed is particularly useful for sensor front ends and high-gain signal conditioning. Typical applications include low-level sensor instrumentation, strain-gauge and bridge amplifiers, precision current measurement, audio preamplification, laboratory measurement equipment, and industrial analog signal chains. The high rejection ratio helps reduce errors caused by common-mode voltage and supply variation, while the low offset drift supports stable calibration over temperature. When designing around the LT1007ACP, check the required gain stability, supply voltage, load conditions, and compensation requirements against the device family data. Decoupling capacitors should be placed close to the supply pins, and the input and feedback paths should be kept short to minimize parasitic capacitance and noise pickup. This product page combines the device specifications, verified source links, application guidance, and package-level design considerations for engineers evaluating the LT1007ACP in precision analog systems.

RFQ پەیوەندی
LT1007CH - Low-Noise Precision Op Amp | Analog Devices
LT1007CH

LT1007CH - Low-Noise Precision Op Amp | Analog Devices

Analog Devices LT1007CH is a low-noise, high-speed precision operational amplifier in a TO-5 package. It provides 2.5 nV/√Hz wideband input noise, guaranteed 4.5 nV/√Hz noise at 10 Hz, guaranteed 3.8 nV/√Hz noise at 1 kHz, and a typical 60 nV peak-to-peak 0.1 Hz to 10 Hz noise figure. Its precision specifications include 10 µV offset voltage, 0.2 µV/°C drift, and 130 dB common-mode and power-supply rejection. These characteristics make the LT1007CH suitable for instrumentation, low-level sensor amplification, and precision signal chains where input-referred noise and DC stability are important. The LT1007 family combines low-noise operation with high-speed performance, while the LT1037 variant provides a 60 MHz gain-bandwidth product and is stable for closed-loop gains of 5 or greater. The LT1007CH is offered as a single, general-purpose amplifier circuit in a TO-5 package. The manufacturer's datasheet states that noise, precision, and speed are combined in one monolithic operational-amplifier family, supporting applications requiring both low-frequency noise performance and accurate signal amplification. Care should be taken with grounding, input lead routing, supply bypassing, and thermal management. The datasheet specifically advises minimizing air currents, keeping package leads short, placing the two input leads close together, and maintaining both inputs at the same temperature. Because the verified distributor data does not provide operating-voltage limits, supply current, input bias current, output swing, gain-bandwidth product for the LT1007, or detailed TO-5 pin assignments, those values are not asserted here. Consult the manufacturer datasheet for those parameters, input and output common-mode limits, saturation behavior, compensation requirements, and the exact pin configuration before final circuit design. The LT1007CH is a precision analog building block for equipment where low-noise, low-offset measurement paths are more important than minimum cost or maximum integration.

RFQ پەیوەندی
LT1007CJ8 - Low-Noise Precision Op Amp | Analog Devices
LT1007CJ8

LT1007CJ8 - Low-Noise Precision Op Amp | Analog Devices

The Analog Devices LT1007CJ8 is a low-noise, high-speed precision operational amplifier with 2.5 nV/√Hz wideband noise, 10 µV offset voltage, 0.2 µV/°C drift, 130 dB common-mode rejection, and 130 dB power-supply rejection. The device is packaged in an 8-pin CERDIP package and is intended for instrumentation, sensor-signal conditioning, and precision analog systems that require low input-referred noise and accurate DC behavior. The LT1007 family combines monolithic low-noise characteristics with a 60 MHz gain-bandwidth product on the decompensated LT1037 variant. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages while providing high input impedance and low output impedance. The LT1007 belongs to the precision operational-amplifier hierarchy, where low input voltage noise, low offset drift, high rejection ratios, and predictable gain behavior are more important than maximum output-current capability. This makes the family suitable for conditioning low-level signals from strain gauges, precision sensors, audio circuits, laboratory instrumentation, and high-resolution measurement systems. The LT1007 combines a 2.5 nV/√Hz noise density with a 2 Hz 1/f corner frequency and approximately 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. Its 10 µV offset voltage and 0.2 µV/°C drift support accurate DC measurements, while 130 dB common-mode rejection and 130 dB power-supply rejection reduce errors caused by common-mode voltages and imperfect supply rails. These characteristics are particularly valuable when the input signal is smaller than the unwanted offsets, noise, or supply ripple present in the measurement chain. The series uses precision internal design techniques to achieve low noise and stable operation. The standard LT1007 is stable for closed-loop gains of 5 or higher, while the decompensated LT1037 provides higher gain-bandwidth-product performance and is also stable at gain 5 or above. Designers must account for this minimum stable gain when selecting feedback values. Decoupling close to the supply pins, maintaining clean ground returns, and avoiding long input traces are therefore central to preserving the intended noise performance. Typical uses include low-level bridge and thermocouple amplification, precision current-to-voltage conversion, audio and instrumentation preamplifiers, low-level sensor interfaces, and laboratory measurement equipment. In these applications, the LT1007 can amplify weak signals close to its noise floor while rejecting common-mode interference and supply-related disturbance. The 8-pin CERDIP package also supports applications that benefit from a through-hole mechanical format rather than a surface-mount land pattern. A key design consideration is that minimum gain stability differs from conventional unity-gain-stable amplifiers. Feedback configurations must provide a gain of at least 5, and input/output capacitance should be checked against the frequency-response and stability requirements in the manufacturer datasheet. Low-noise performance also depends on resistor selection, source impedance, grounding, supply bypassing, and shielding rather than the amplifier alone. This product overview consolidates the LT1007CJ8 electrical characteristics, package information, drop-in-family alternatives, and practical application guidance. It supports faster engineering comparisons while directing detailed pin assignments, test conditions, and absolute-maximum ratings to the official Analog Devices LT1007 datasheet and product documentation.

RFQ پەیوەندی
LT1007CJG - Low-Noise Precision Op Amp | Texas Instruments
LT1007CJG

LT1007CJG - Low-Noise Precision Op Amp | Texas Instruments

The Texas Instruments LT1007CJG is a single, low-noise precision operational amplifier with 2.5 nV/√Hz wideband input-noise density, 10 µV offset voltage, and 0.2 µV/°C input-offset drift, packaged in an 8-pin CDIP. It combines low-noise performance with high open-loop gain and strong common-mode rejection for accurate analog signal conditioning. An operational amplifier is a voltage-feedback amplifier that uses high differential gain to amplify the difference between its non-inverting and inverting inputs. Within the wider signal-chain hierarchy, the LT1007CJG belongs to the precision amplifier class, which sits between general-purpose amplifiers and instrumentation amplifiers. Its noise and offset characteristics make it suitable when signals must be measured, converted, filtered, buffered, or referenced with little added error. The LT1007 series emphasizes low-noise signal handling with a 1/f noise corner frequency of 2 Hz and 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. The 10 µV input-offset voltage and 0.2 µV/°C drift limit input-referred error in slowly varying or high-gain stages. The amplifier also provides 130 dB common-mode rejection and power-supply rejection, reducing sensitivity to supply noise and shared ground-bus disturbances. A unity-gain-stable configuration supports direct signal buffering, while the instrumentation characteristics support precision gain stages. The device is intended for low-level sensor front ends, strain-gage and bridge excitation, precision current-to-voltage conversion, audio and low-frequency measurement circuits, laboratory instrumentation, and high-gain analog systems. Decoupling capacitors should be placed close to the supply pins so switching ripple and high-frequency supply variation do not modulate the output. For DC-sensitive applications, account for input-bias current of 55 nA when working with high-impedance sources. Because the CDIP package has eight through-hole leads, the amplifier fits conventional 0.300-inch, 7.62 mm row spacing and is easy to prototype or socket on laboratory and industrial boards. This page consolidates the LT1007CJG electrical characteristics, package details, design guidance, and drop-in family alternatives into a single engineering reference. Use the pin-description table and application information in the manufacturer datasheet when assigning PCB tracks, bypassing supply rails, and closing the loop around this amplifier.

RFQ پەیوەندی
LT1007IS8 - Low-Noise Precision Op Amp | Analog Devices
LT1007IS8

LT1007IS8 - Low-Noise Precision Op Amp | Analog Devices

The Analog Devices LT1007IS8 is a single-circuit, low-noise precision operational amplifier designed for accurate signal amplification, with 8 MHz gain bandwidth, 2.5 nV/√Hz wideband noise, 10 µV offset voltage, and 0.2 µV/°C drift. The device is offered in an 8-lead SOIC package and operates across a -55°C to +125°C temperature range. A precision operational amplifier is a voltage-input analog integrated circuit that amplifies the difference between two input voltages. The LT1007 belongs to the operational-amplifier hierarchy, combining low-noise input stages, high open-loop gain, accurate offset behavior, and common-mode rejection. This makes it useful when a signal must be amplified without adding substantial noise or allowing supply variation and input offset to distort the result. The principal performance feature is the LT1007 family's exceptionally low wideband noise density of 2.5 nV/√Hz. Its 1/f noise corner is 2 Hz, while the manufacturer describes 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. Precision is supported by 10 µV offset voltage, 0.2 µV/°C drift, and 130 dB common-mode and power-supply rejection. The LT1007 is optimized for low-noise signal conditioning rather than the very high gain-bandwidth operation of the decompensated LT1037. The LT1007IS8's 8 MHz gain bandwidth provides useful bandwidth for audio, instrumentation, sensor, and control signals. Because the gain-bandwidth product limits closed-loop bandwidth, higher closed-loop gains reduce usable bandwidth. Input and output stability, source resistance, capacitive loading, and the power-supply bypass network must therefore be considered together when establishing signal-chain performance. Typical uses include low-level sensor amplification, audio preamplification, strain-gauge and bridge-based measurements, precision current-to-voltage conversion, and analog instrumentation. The low-noise characteristic is especially valuable when the source impedance is similar to or below a few hundred ohms, although source resistance, resistor noise, and input-bias-current error must be evaluated together. A practical design should keep feedback resistors and sensitive input nodes physically compact, use low-noise resistors where appropriate, and place bypass capacitors close to the supply pins. The 8-lead SOIC footprint permits conventional surface-mount assembly, but thermal performance and output drive remain important when driving heavy loads or operating across the extended temperature range. This page combines the manufacturer's precision and noise characteristics, package information, drop-in alternatives, application guidance, and design considerations to provide a practical engineering reference for selecting and implementing the LT1007IS8.

RFQ پەیوەندی
LT1007MLB - Low-Noise Precision Op Amp | Texas Instruments
LT1007MLB

LT1007MLB - Low-Noise Precision Op Amp | Texas Instruments

Texas Instruments LT1007MLB is a single-circuit, low-noise precision operational amplifier packaged in an 8-pin TO-99 metal-can package. The LT1007MLB is identified as a military-temperature-grade component with a through-hole, round-package construction and wire-form terminals. According to the manufacturer product page for the LT1007 family, the amplifier combines low-voltage noise with precision offset, drift, common-mode rejection, and power-supply rejection specifications. The family is specified with 10 µV offset voltage, 0.2 µV/°C offset drift, 130 dB common-mode rejection, and 130 dB power-supply rejection. An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to increase the voltage level of a low-amplitude input. Its wider role within analog electronics includes closed-loop gain, active filtering, instrumentation, buffer amplification, and feedback control. The LT1007 family is positioned for applications where low input noise, input-offset accuracy, and low drift are more important than compactness or low power consumption. Noise performance is a principal benefit of the LT1007 family. The manufacturer specifies 2.5 nV/√Hz wideband input noise, a 2 Hz 1/f corner frequency, and 60 nV peak-to-peak noise over the 0.1 Hz to 10 Hz band. These characteristics make the amplifier suitable for precision signal-chain work in which the amplifier must preserve weak signals without adding excessive broadband or low-frequency noise. The device is a single amplifier rather than a multi-channel integrated package. The precision specifications further distinguish the LT1007 from general-purpose amplifiers. A 10 µV input-offset voltage and 0.2 µV/°C drift support stable operation when source impedance, temperature, or input common-mode conditions vary. The specified 130 dB common-mode rejection ratio reduces output movement caused by common-mode input voltage, while 130 dB power-supply rejection reduces sensitivity to supply ripple. These specifications are particularly useful in measurement and control systems that require accurate amplification of small differential signals. Typical uses include precision sensor interfaces, low-level instrumentation, strain-gauge and bridge-amplifier signal paths, high-resolution measurement equipment, low-noise filter stages, and laboratory analog systems. The TO-99-8 package favors legacy instrumentation, military-style equipment, and prototypes where a through-hole metal-can package is convenient. Its physical size and eight terminals make it more appropriate for through-hole designs than compact mixed-signal equipment. Designers should account for the metal-can package, required supply rails, input-common-mode range, output swing, stability, and compensation requirements when assigning the amplifier. The LT1007 is not decompensated; the 60 MHz gain-bandwidth statement in the manufacturer material applies to the related LT1037, not automatically to LT1007MLB. Follow the manufacturer pin-description table when making PCB connections and verify the exact operating limits for the grade and suffix. This product overview combines the exact LT1007MLB package and ordering information with the manufacturer’s family-level precision, noise, rejection, and supply specifications. It also distinguishes directly verified device facts from parameters that require confirmation from the complete LT1007 datasheet.

RFQ پەیوەندی
LT1007XH - Low-Noise 200°C Op Amp in TO-5 | Analog Devices
LT1007XH

LT1007XH - Low-Noise 200°C Op Amp in TO-5 | Analog Devices

Analog Devices LT1007XH is a single-circuit, low-noise operational amplifier specified for operation up to 200°C and supplied in a hermetic TO-5 package. It combines 10 µV offset voltage, 0.2 µV/°C offset drift, 130 dB common-mode rejection, and 130 dB power-supply rejection with monolithic noise performance of 2.5 nV/√Hz. The 1/f noise corner is 2 Hz, and 0.1 Hz-to-10 Hz noise is 60 nV peak-to-peak, making the device suitable for precision analog signal chains requiring low voltage noise and low drift. An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, filter, compare, or control analog signals. The LT1007 belongs to the precision operational-amplifier hierarchy, where low input noise, low offset drift, high rejection, and stable operation are more important than maximum bandwidth or minimum cost. Its wide operating-temperature capability extends that precision-focused role to industrial, instrumentation, and high-temperature analog systems. Key features include a 10 µV input offset voltage, 0.2 µV/°C input offset drift, and 130 dB common-mode rejection. The manufacturer describes a 2.5 nV/√Hz wideband noise density, a 2 Hz 1/f corner, and 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. The manufacturer datasheet also states that these devices are 100% tested at 200°C ±3°C, with normal operating-temperature specifications provided separately for the LT1007M version. The LT1007 series was designed as a direct replacement for the OP-27 operational-amplifier family, as stated in the manufacturer datasheet. This heritage is important because it provides an established precision-amplifier upgrade path for existing instrumentation and signal-conditioning designs. The LT1007XH combines the series noise and precision characteristics with a hermetic TO-5 construction intended to support demanding thermal environments. Typical uses include precision instrumentation, low-level sensor amplification, bridge and strain-gauge signal conditioning, laboratory measurement equipment, and industrial analog front ends. Its low-noise and low-drift characteristics are particularly valuable when the input signal is small and the useful measurement must remain stable despite temperature changes. In these applications, the amplifier is usually placed directly in front of an ADC or downstream measurement chain. When designing with the LT1007XH, verify the exact LT1007XH electrical limits from the manufacturer datasheet rather than substituting the normal-temperature LT1007M limits. Decoupling, input-bias-current compensation, source impedance, output loading, and stability must be evaluated around the selected noise and gain conditions. The hermetic package also requires attention to lead strain, thermal expansion, and PCB soldering practices. This page combines verified manufacturer specifications, current distributor sourcing information, same-package drop-in candidates, and practical selection guidance. It also distinguishes the uniquely tested LT1007XH temperature grade from ordinary package-code or reel-code variants, helping engineers make a replacement decision based on electrical compatibility and environmental requirements.

RFQ پەیوەندی
LT1008CH - Picoamp Precision Operational Amplifier | Analog Devices
LT1008CH

LT1008CH - Picoamp Precision Operational Amplifier | Analog Devices

The Analog Devices LT1008CH is a single-circuit precision operational amplifier in an 8-lead round TO-5 hermetic package, combining picoampere input bias current, microvolt-level offset voltage, low noise, and very high common-mode and power-supply rejection. It operates from dual supplies up to ±18 V and can deliver 5 mA of load current, making it suitable for instrumentation, precision measurement, low-level signal conditioning, and current-to-voltage conversion. An operational amplifier is a high-gain differential amplifier whose output responds to the voltage difference between its non-inverting and inverting inputs. Negative feedback causes the amplifier to amplify only the signal presented within its linear operating range while rejecting common-mode voltage and supply-noise variations. Within the broader hierarchy, the LT1008CH is an instrumentation amplifier, an operational amplifier, an analog amplifier, a semiconductor, and ultimately a linear integrated circuit. The LT1008 family's defining characteristic is input bias current maintained in the picoampere range over the full -55°C to 125°C temperature range. This behavior makes the device useful with high-impedance sources, charge-sensitive transducers, leakage-sensitive sensors, and precision bridges where conventional CMOS or bipolar amplifiers may introduce unacceptable input-current error. The microvolt offset specification and low drift support stable DC measurements, while low voltage noise and current noise improve the useful resolution of small-signal chains. Extremely high common-mode rejection ratio and power-supply rejection ratio allow the LT1008 to reject interference coupled from the input source or from imperfect power-supply rails. These characteristics matter in systems where the signal of interest is small but supply noise and ground offsets are much larger. The manufacturer describes the device as a universal precision operational amplifier suitable for practically all precision applications. Typical uses include precision strain-gauge and bridge amplifiers, low-current pH and ion-selective measurement front ends, photodiode and charge-sensitive preamplifiers, laboratory references, low-leakage buffer stages, and precision current-to-voltage converters. The 8-lead TO-5 construction is mechanically robust and suited to laboratory, industrial, and instrumentation systems where through-hole mounting and hermetic construction are preferred. When designing around the LT1008CH, account for input-bias-current error in the feedback network, provide adequate supply bypassing at the pins, and use guarding to minimize leakage on high-impedance nodes. Because the device can operate from ±18 V, verify the complete circuit's absolute maximum voltages and ensure input common-mode limits are respected during startup and fault conditions. This page consolidates manufacturer specifications, sourcing information, application guidance, and design notes that are not consolidated in a single distributor listing.

RFQ پەیوەندی
LT1008IN8 - Precision Picoamp Op Amp | Analog Devices
LT1008IN8

LT1008IN8 - Precision Picoamp Op Amp | Analog Devices

Analog Devices LT1008IN8 is a single precision operational amplifier with picoampere input bias current, microvolt-level offset voltage, low noise, and a 5 mA output-current capability, packaged in an 8-pin PDIP. The device is designed for instrumentation and signal-chain applications where input leakage, offset stability, common-mode rejection, and power-supply rejection are more important than wide bandwidth. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs while providing very high open-loop gain. The LT1008 belongs to the precision operational-amplifier category and, more broadly, to the signal-chain and analog IC hierarchy. Its unusually low bias current enables accurate sensing from high-impedance sources, sensors, transducers, and leakage-sensitive measurement circuits without adding substantial input-referred error. The LT1008 combines picoampere bias currents maintained across the -55°C to 125°C temperature range with microvolt offset voltage, low offset drift, low voltage and current noise, and low power dissipation. According to the Analog Devices LT1008 datasheet, the amplifier can deliver 5 mA of load current while retaining high voltage gain. It also provides extremely high common-mode and power-supply rejection ratios, making it effective in systems where supply ripple or input-common-mode variation could otherwise degrade measurement accuracy. The LT1008 is implemented as a bipolar precision amplifier. Its low bias current reduces error when the source impedance is high, while its precision reference and offset characteristics support stable null and calibration behavior over time and temperature. The amplifier is intended for general-purpose precision applications rather than high-speed signal conditioning, making stability and noise more important than slew rate or gain-bandwidth performance. Typical uses include low-level sensor signal conditioning, electrochemical and biomedical instrumentation, photodiode amplifiers, precision current-to-voltage conversion, leakage measurement, strain-gauge bridges, and laboratory test equipment. Its low-noise and high-rejection characteristics are especially useful when the useful signal is small relative to the input offset or supply ripple. For best performance, use suitable bypassing on the supply pins, keep input and feedback traces short, and avoid contamination or leakage pathways on high-impedance nodes. The offset specifications should be evaluated over the actual temperature range, and input protection must be designed to prevent excessive differential voltage or common-mode voltage. The IN8 suffix identifies the industrial-temperature PDIP package option, so board layout and thermal requirements should follow the package drawing rather than a surface-mount footprint. This page consolidates the manufacturer's device information, distributor availability references, a precise package pinout, compatibility guidance, and practical design notes. It also distinguishes the only confirmed same-footprint alternative from functionally similar amplifiers that cannot be soldered directly into an existing PDIP-8 footprint.

RFQ پەیوەندی
LT1010CH - ±150mA Fast Power Buffer | Analog Devices
LT1010CH

LT1010CH - ±150mA Fast Power Buffer | Analog Devices

The Analog Devices LT1010CH is a fast, unity-gain power buffer designed to increase the output-current capability of existing integrated-circuit operational amplifiers by more than an order of magnitude. The device is specified for output current up to ±150mA and is supplied in the TO-39, 3-lead metal-can package identified by the CH suffix. Its primary role is to buffer a low-current op-amp output while preserving high speed and reducing sensitivity to capacitive loading. A power buffer is an analog amplifier stage used between a precision or high-impedance signal source and a load that requires substantially more output current than the source can supply. In the signal-chain hierarchy, the LT1010 is a power buffer amplifier, which is a specialized type of voltage-feedback operational-amplifier output stage. The unity-gain configuration makes the buffered output follow the driving op-amp voltage closely while adding drive capability rather than voltage gain. Key verified characteristics include a nominal 20 MHz bandwidth and ±150mA output-current capability. The TO-39 package is a round, 3-terminal metal-can package with wire-form leads. According to the manufacturer datasheet, the LT1010 is intended to increase the output capability of existing op amps by more than an order of magnitude. This makes it useful when driving heavier capacitive, resistive, or current-intensive analog loads while retaining a relatively simple external circuit. The LT1010 is particularly relevant to precision DC amplifiers, instrumentation, signal-conditioning systems, and laboratory or industrial analog designs. Its fast behavior can improve transient response and make the driving amplifier less sensitive to capacitive loading. Unlike a discrete complementary output stage, the integrated device also reduces thermal feedback inside precision amplifier designs, according to the Analog Devices datasheet. The CH package should be checked carefully against the manufacturer pinout before PCB assembly because the TO-39 lead assignment and metal-can orientation are essential to correct operation. The verified web data identifies the package as TO-39-3 and describes the device as a 1-circuit buffer amplifier. The manufacturer product page also lists the LT1010 family in 8-pin miniDIP, plastic TO-220, and 8-pin DFN packages, but the CH ordering code is the metal-can TO-39 variant. When using the LT1010CH, verify the output-current rating, supply voltage, thermal conditions, stability requirements, and maximum output-voltage swing against the specific application. The TO-39 package requires attention to thermal dissipation and soldering profile. Because the output stage can source and sink substantial current, the load return path, bypassing, and grounding should be arranged to prevent large transient currents from disturbing sensitive analog nodes. This page combines the verified manufacturer datasheet, distributor identification, package information, and application guidance with practical selection, thermal, and circuit-layout considerations. It also distinguishes the verified LT1010CH characteristics from parameters that require confirmation in the complete manufacturer datasheet.

RFQ پەیوەندی
LT1010CK - Fast ±150mA Power Buffer | Analog Devices
LT1010CK

LT1010CK - Fast ±150mA Power Buffer | Analog Devices

The Analog Devices LT1010CK is a fast, unity-gain power buffer capable of sourcing or sinking ±150 mA and is supplied in a TO-3 package. It is designed to increase the output-current capability of existing integrated-circuit operational amplifiers by more than an order of magnitude. The LT1010CK is particularly useful when an amplifier must drive heavier loads while maintaining fast response and reduced sensitivity to capacitive loading. A power buffer is a specialized amplifier stage placed between a low-current operational amplifier and a load. Its role in the signal-chain hierarchy is broader than ordinary voltage amplification: the upstream op-amp establishes gain and signal accuracy, while the buffer provides current drive, isolation, and improved load behavior. The LT1010CK operates as a unity-gain buffer, so its nominal signal gain is 1. This arrangement is commonly used in precision DC amplifiers, instrumentation systems, signal-conditioning circuits, and applications requiring more output current than a conventional op-amp can provide. The key feature of the LT1010CK is its fast, bipolar power-buffer architecture with ±150 mA output capability. According to the manufacturer datasheet, the device can increase the output capability of an existing IC op-amp by more than an order of magnitude. Its unity-gain configuration also makes the buffer less sensitive to capacitive loading and helps reduce thermal feedback in precision DC amplifier circuits. The manufacturer identifies the product as being in production. The LT1010 family is offered in multiple package options, including an 8-pin miniDIP, plastic TO-220 and 8-pin DFN packages. The low thermal resistance of the power package is intended to assist in reducing operating junction temperatures, although the LT1010CK’s wider TO-3-style package requires careful attention to heat dissipation and lead clearance. The datasheet specifically identifies the device as a fast ±150 mA power buffer. Typical applications include boosting the drive of precision operational amplifiers, driving high-current feedback networks, buffering instrumentation signals, and supplying greater output current into downstream stages. It can also improve the behavior of fast amplifier systems when capacitive loads would otherwise disturb the upstream amplifier. Its combination of speed, current capability, and unity-gain isolation makes it useful in laboratory, industrial control, and signal-conditioning equipment. Designers should verify the exact pin functions, electrical limits, thermal conditions, and stability requirements against the manufacturer datasheet before implementation. A power buffer must be checked for DC power dissipation, output-current direction, source-to-sink transitions, and the voltage and temperature limits of every connected stage. Layout should minimize parasitic feedback paths and maintain adequate thermal spreading around the power package. This page combines the verified manufacturer product information, distributor availability references, package identification, pricing information, and engineering guidance in one concise design resource. It also distinguishes documented LT1010 family options from true drop-in replacements, avoiding unsupported substitute claims where verified pin-compatible alternatives are not available.

RFQ پەیوەندی
LT1012CD - Precision Op Amp, 25µV Offset, 8-SOIC | Texas Instruments
LT1012CD

LT1012CD - Precision Op Amp, 25µV Offset, 8-SOIC | Texas Instruments

The Texas Instruments LT1012CD is a precision operational amplifier featuring 25 µV input offset voltage, 40 pA input bias current, and 200 µV typical offset in an 8-pin SOIC package. Originally designed by Linear Technology and now produced by Texas Instruments and authorized partners, the LT1012CD delivers picoampere-level bias currents over the full -55°C to +125°C temperature range with extremely high common-mode and power supply rejection ratios. A precision operational amplifier (op-amp) is a high-gain DC-coupled electronic voltage amplifier with a differential input and, usually, a single-ended output. Precision op-amps are characterized by low input offset voltage, low input bias current, low noise, and high common-mode rejection ratio (CMRR), making them suitable for amplifying small signals from sensors, transducers, and high-impedance sources. The LT1012 belongs to the broader category of linear integrated circuits and is positioned as a universal precision op-amp that combines the low-bias performance of BIFET/JFET-input amplifiers with the low-offset and low-drift characteristics of precision bipolar designs. Key features of the LT1012CD include 200 µV maximum input offset voltage, 40 pA maximum input bias current, 0.2 V/µs typical slew rate, and the ability to deliver 5 mA of output current while maintaining a voltage gain of one million. The device operates over a wide supply range (typically ±2 V to ±20 V) and offers extremely high CMRR and PSRR, with practically unmeasurable warm-up drift, making it ideal for precision instrumentation. The LT1012CD uses Linear Technology's advanced bipolar process technology that achieves sub-picoampere bias currents through active bias-current cancellation, while the precision bandgap-based input stage provides the low offset and low drift. The amplifier is internally compensated, eliminating the need for external compensation components in most applications, simplifying PCB layout and reducing BOM cost. Typical applications include precision thermocouple amplification, strain-gauge and weigh-scale signal conditioning, medical instrumentation, high-impedance sensor buffers, precision integrators for analog computation, and battery-powered portable instrumentation where the LT1012 achieves precision operation on two Ni-Cad batteries with only 1 mW of power dissipation. When designing with the LT1012CD, note that its 0.2 V/µs slew rate makes it suitable for DC and low-frequency signals but inadequate for high-speed or wide-bandwidth applications. For those applications, a faster op-amp such as the LT1028 or OP-27 should be considered. Standard 8-SOIC layout conventions apply, with input pins (IN+, IN-) at pins 3 and 2, output at pin 6, and power pins at pins 7 (V+) and 4 (V-). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet to support fast engineering decisions.

RFQ پەیوەندی
LT1012CH - Picoamp Precision Op Amp | Analog Devices
LT1012CH

LT1012CH - Picoamp Precision Op Amp | Analog Devices

Analog Devices LT1012CH is a single-circuit, internally compensated precision operational amplifier with picoampere input bias current, microvolt offset voltage, low voltage noise, low current noise, and very high input impedance. It operates from a single positive supply and can provide a closed-loop voltage gain of one million while delivering a 5 mA load current. The device is offered in an 8-lead round TO-5 metal-can package with wire-form leads. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LT1012 belongs to the precision operational-amplifier hierarchy, combining high open-loop gain with low offset, low bias current, and low-noise behavior. These characteristics make it useful when the source impedance can be high enough that input bias-current error would overwhelm a conventional amplifier. The LT1012's principal features include picoampere bias currents maintained across the full -55°C to +125°C temperature range, microvolt offset voltage, low offset drift with time and temperature, and exceptionally high common-mode and power-supply rejection ratios. According to the manufacturer, precision operation on two Ni-Cad batteries is possible with 1 mW of power dissipation. The reported 5 mA load-current capability and gain of one million are particularly useful for precision buffer, instrumentation, transducer, and low-level signal-chain applications. The LT1012 is implemented as a bipolar precision amplifier and is internally compensated for unity-gain stability. This architecture supports simple voltage-follower use without external compensation while retaining accurate low-frequency operation. The high gain and very low input current also make the device suitable for guarding, electrochemical measurement, photodiode amplification, and other applications where source leakage and offset can dominate measurement accuracy. Typical uses include precision sensor interfaces, low-current transducers, battery-powered instruments, pH and conductivity measurement circuits, photodiode amplifiers, and analog test equipment. The hermetic metal-can package provides a mechanically robust option for applications requiring stable operation over an extended temperature range, although engineers should observe the manufacturer's specified lead orientation and connection requirements. When using the LT1012CH, minimize leakage around the input pins and keep sensitive input traces away from power and ground paths. Because very high open-loop gain makes offset, bias-current error, and leakage especially important, clean PCB surfaces, guarded inputs, suitable bypassing, and careful source-impedance balancing are essential. This page combines verified manufacturer and distributor information with practical implementation guidance and clearly identified drop-in alternatives.

RFQ پەیوەندی
LT1012CJ8 - Precision Operational Amplifier | Analog Devices
LT1012CJ8

LT1012CJ8 - Precision Operational Amplifier | Analog Devices

Analog Devices LT1012CJ8 is a single-circuit, internally compensated precision operational amplifier in an 8-pin CERDIP package. It is designed for low-noise signal conditioning, instrumentation, and precision analog measurement. Key characteristics include picoampere-level bias current, very high common-mode and power-supply rejection, extremely low warm-up drift, a voltage gain of one million, and the ability to deliver 5 mA of load current. The device operates with supply voltages extending to ±20 V. A precision operational amplifier is a voltage-feedback amplifier that uses high open-loop gain and negative feedback to amplify small signals accurately. Within the electronics hierarchy, the LT1012 is an operational amplifier, a type of analog amplifier and analog integrated circuit used for instrumentation, buffering, error amplification, and signal conditioning. Its unusually low bias current makes it particularly useful when source leakage and input-current error must remain small. The LT1012 combines low-noise operation with exceptional common-mode and power-supply rejection ratios. Picoampere bias currents remain maintained over the stated temperature range, reducing errors in high-impedance measurement circuits. A gain of one million supports high closed-loop precision when appropriate feedback resistors are used, while the 5 mA load-current capability allows the amplifier to drive moderate loads rather than operate strictly as a high-impedance buffer. The internal compensation makes the LT1012 broadly applicable without external compensation components. This simplifies precision circuit design when the required stability characteristics match the manufacturer's recommended configurations. Its low warm-up drift helps maintain calibration consistency in circuits where output movement after power application would degrade accuracy. Typical uses include low-level sensor amplification, strain-gauge and bridge-based measurement, precision instrumentation, low-level signal conditioning, and buffering applications. The 5 mA output-current capability is useful when driving a moderate input load, while the high open-loop gain and rejection characteristics support accurate amplification of small differential signals. When connecting the LT1012CJ8, follow the manufacturer pin-description table and observe the supply-voltage limits. Decoupling capacitors should be placed close to the supply pins, and sensitive input nodes should be kept away from high-current return paths to minimize parasitic pickup. Feedback resistor values and source impedances should be selected to maintain the intended noise, bias-current, and stability performance. This product page combines the manufacturer's functional description with package information, application guidance, sourcing structure, and explicit drop-in alternative evaluation. It is intended to help engineers distinguish verified characteristics from assumptions and to plan a PCB or legacy-system replacement before committing to a component change.

RFQ پەیوەندی
LT1012DJ8 - Precision Picoamp Op Amp | Analog Devices
LT1012DJ8

LT1012DJ8 - Precision Picoamp Op Amp | Analog Devices

The Analog Devices LT1012DJ8 is a precision, internally compensated universal operational amplifier designed for low-level instrumentation and measurement applications. The LT1012 family combines picoampere input bias currents, extremely high common-mode rejection, high power-supply rejection, very low warm-up drift, and an offset voltage measured in microvolts. According to the Analog Devices product page, the device can deliver a 5 mA load current with a voltage gain of one million, making it suitable for precision transimpedance, sensor-interface, strain-gauge, and low-level signal-conditioning circuits. An operational amplifier is a voltage-feedback active component that uses high open-loop gain to amplify small differential signals. The LT1012 belongs to the precision operational amplifier category, a subtype of instrumentation amplifiers and analog signal-chain ICs. Its internally compensated architecture allows use without external frequency-compensation components in voltage-follower and inverting amplifier configurations. The low bias current is particularly valuable when the source impedance is high, because bias-current error at the input contributes directly to output offset. The LT1012DJ8 is specified for a temperature range of 55°C to 125°C in the LT1012 family description. The DJ8 package is an 8-pin ceramic through-hole DIP package, with a 0.300 inch lead pitch and 7.62 mm body width according to the listed distributor package data. The package designation distinguishes the DJ8 ceramic DIP ordering code from the plastic DIP variants of the same amplifier family. The device is intended for applications requiring accurate current measurement and low-level voltage amplification. A picoampere-class bias current reduces loading of high-impedance transducers, while the very high common-mode rejection ratio allows small sensor signals to be amplified in the presence of substantial common-mode voltage. The LT1012 can also be used with a gain of one million, although practical board layout, resistor matching, parasitic capacitance, and stability requirements become increasingly important at high closed-loop gains. Designers should preserve the precision specifications with short, guarded input traces, clean grounding, and symmetrical resistor networks. The manufacturer's LT1012 datasheet should be consulted for the exact offset voltage, input bias current, common-mode range, supply current, maximum input voltage, output swing, and pin configuration before finalizing a circuit. For applications where the ceramic DIP package is unnecessary, the plastic DIP ordering codes provide an alternative construction, but package construction, temperature grade, and lifecycle requirements should be compared before substitution.

RFQ پەیوەندی
LT1012IJ8 - Precision Picoamp Op Amp | Analog Devices
LT1012IJ8

LT1012IJ8 - Precision Picoamp Op Amp | Analog Devices

The Analog Devices LT1012IJ8 is a single-circuit precision operational amplifier with picoampere input bias current, microvolt-level input offset voltage, and low-noise performance, housed in an 8-pin CERDIP package. The device is specified for a low input bias current of 25 pA, an input offset voltage of 8 uV, and an industrial operating temperature range from -40°C to +85°C. The LT1012IJ8 is currently listed as obsolete. A precision operational amplifier is a voltage-input, voltage-output amplifier designed to minimize errors introduced by input bias current, offset voltage, drift, noise, and common-mode voltage. Within the amplifier hierarchy, it belongs to the precision op-amp category, combining low-dropout operation, low-power capability, and high input impedance for instrumentation, buffering, and signal-conditioning systems where source leakage and DC accuracy are important. The LT1012IJ8 provides picoampere-class bias-current behavior over its operating range, helping minimize error when measuring high-impedance sources. Its 8 uV offset specification supports accurate amplification of small signals, while the internally compensated architecture simplifies closed-loop use. The manufacturer also identifies very high common-mode and power-supply rejection ratios, very low warm-up drift, and the ability to deliver 5 mA of load current at a voltage gain of one million. Low power is central to the device architecture. Analog Devices states that the LT1012 can operate from two Ni-Cad batteries while dissipating 1 mW, making it suitable for portable precision systems where available energy and thermal rise are constrained. Its precision characteristics are maintained from -55°C to +125°C for the LT1012 family, while the LT1012IJ8 order code is specified for -40°C to +85°C. Typical uses include pH and electrochemical measurement front ends, photodiode and other high-impedance sensor amplifiers, precision current-to-voltage converters, low-level instrumentation, and battery-powered measurement equipment. In these applications, low bias current reduces leakage across sensitive sources, while low offset voltage helps preserve signal integrity at the input stage. Layout should keep input-node leakage to a minimum, provide clean grounding around the signal path, and use guarding where surface contamination or PCB leakage could otherwise dominate picoampere measurements. The power supply must remain within the manufacturer-specified operating limits, and output drive should match the required load and feedback network. This product page combines the LT1012IJ8 precision specifications, operating-class information, sourcing workflow, and application-focused design guidance with explicit distinctions between the obsolete orderable MPN and the broader LT1012 family.

RFQ پەیوەندی
LT1012IN8 - Picoamp Input Precision Op Amp | Analog Devices
LT1012IN8

LT1012IN8 - Picoamp Input Precision Op Amp | Analog Devices

Analog Devices LT1012IN8 is a picoamp-input, microvolt-offset precision operational amplifier with a 5 mA output-current capability, approximately 1 mW power dissipation on two Ni-Cad batteries, and an 8-pin PDIP package. The LT1012 family combines extremely low input bias current with high common-mode rejection, high power-supply rejection, low voltage noise, low current noise, and minimal warm-up drift. A precision operational amplifier is a voltage-feedback amplifier designed to minimize error contributions from input bias current, offset voltage, drift, noise, and power-supply variation. Within the broader hierarchy of semiconductor devices, the LT1012 is an analog integrated circuit, and within analog integrated circuits it belongs to the precision operational-amplifier family. Its internally compensated architecture allows it to operate as a closed-loop amplifier without an external compensation capacitor. The principal benefits of the LT1012IN8 are picoampere-scale input bias current maintained across the full -55 °C to 125 °C temperature range, microvolt-scale input offset voltage, low offset drift, and low voltage and current noise. The manufacturer identifies the device as a universal precision amplifier for instrumentation buffers, low-level signal conditioning, sensor interfaces, battery-powered measurement systems, photodiode amplifiers, and high-impedance transducers. Its low-power operating characteristics are particularly useful when the amplifier must operate from small-cell or dual-cell sources. Technically, the LT1012 combines low input bias current with low offset voltage and drift rather than optimizing only one parameter. This balance is important because high source impedance can convert input leakage into a substantial input-voltage error, while long-term measurement accuracy can be limited by offset drift. The common-mode and power-supply rejection characteristics also reduce errors caused by signal-source reference shifts and supply variation. Internally compensated operation simplifies closed-loop design while retaining stable operation in precision amplifier topologies. Typical applications include pH and electrochemical sensor amplification, photodiode and optical-sensor signal chains, high-impedance instrumentation, low-current measurement, precision bridge amplifiers, and battery-operated test equipment. In these systems, the LT1012 can serve as a non-inverting buffer, inverting amplifier, transimpedance amplifier, or instrumentation-amplifier input stage. The 5 mA load-current capability supports the low-power signal paths associated with portable and industrial measurement systems. Design should begin by checking input common-mode range, output swing, supply current, and stability for the intended feedback network. Input-bias-current error should be calculated using the source impedance, while offset and drift requirements should be evaluated over the actual temperature span. Because the LT1012IN8 is a legacy PDIP device, board layout, socket availability, thermal exposure, and obsolescence-risk management may influence lifecycle planning. This product record combines manufacturer electrical characteristics, package and ordering information, source-document links, practical application guidance, and a structured comparison of confirmed same-package alternatives. It also highlights the engineering trade-offs that matter when selecting a picoamp-input precision amplifier for high-impedance, low-power measurement systems.

RFQ پەیوەندی
LT1013AIP - Dual Precision Op Amp, 4V-44V, DIP-8 | TI
LT1013AIP

LT1013AIP - Dual Precision Op Amp, 4V-44V, DIP-8 | TI

The Texas Instruments LT1013AIP is a dual precision operational amplifier with a 4 V to 44 V supply range, low supply current, low noise, and high open-loop gain. The device is supplied in an 8-pin PDIP package designated for industrial temperature operation and through-hole PCB assembly. It contains two independent precision amplifier sections in an industry-standard dual-op-amplifier pin configuration. A precision operational amplifier is a voltage-feedback amplifier designed to amplify small differential signals while minimizing offset voltage, input bias current, noise, and drift. The LT1013 belongs to the operational-amplifier hierarchy within analog signal-chain ICs, combining a high-impedance differential input stage with a low-distortion output stage. Its broad supply range makes it suitable for both low-voltage instrumentation and higher-voltage industrial signal chains. The LT1013 family combines high gain with low supply current, low noise, and a low offset-voltage temperature coefficient. Manufacturer documentation identifies the family as a precision dual amplifier with performance suited to battery-powered precision instrumentation, strain-gauge signal conditioning, thermocouple amplification, instrumentation amplifiers, and 4 mA to 20 mA current-loop transmitters. The wide operating supply supports both single 5 V and dual positive and negative supply arrangements. Each amplifier section operates independently, allowing simultaneous conditioning of two related signals or use as a single amplifier with the other section acting as a buffer. The industrial-grade through-hole package favors laboratory instruments, legacy industrial controllers, test equipment, and maintenance-friendly designs where socketed or hand-inserted assembly is useful. The 8-pin PDIP footprint also simplifies repair and retrofit work compared with fine-pitch surface-mount packages. Typical applications include precision bridge and strain-gauge front ends, low-level sensor instrumentation, thermocouple and RTD signal conditioning, active filters, threshold detection, and buffered 4 mA to 20 mA current-loop outputs. Because the operating supply extends to 44 V, the amplifier can also support higher-voltage industrial interfaces when the surrounding circuit and protection network are properly rated. When designing a new PCB, follow the manufacturer pin-description table for every connection and preserve the standard dual-op-amplifier footprint. Place input, feedback, and compensation components close to the relevant amplifier pins, and check the selected resistor and capacitor values against the stability requirements described in the LT1013 manufacturer datasheet. This page organizes the LT1013AIP supply, packaging, pinout, drop-in alternatives, application fit, and design considerations into one engineering-focused reference. It also compares the exact MPN with legacy precision and general-purpose dual-op-amplifier alternatives so engineers can identify the closest replacement without assuming electrical equivalence.

RFQ پەیوەندی
LT1013CD - Dual Precision 1MHz Op Amp | Texas Instruments
LT1013CD

LT1013CD - Dual Precision 1MHz Op Amp | Texas Instruments

The Texas Instruments LT1013CD is a low-power dual precision operational amplifier with a 4 V to 44 V supply range, 1 MHz gain-bandwidth product, 0.4 V/us slew rate, and two amplifiers in an 8-pin SOIC package. The device combines high gain, low noise, low supply current, and low-offset-voltage temperature coefficient in one circuit. According to the Texas Instruments product page, LT1013CD is the lead-free SOIC orderable version of the LT1013 family. An operational amplifier is an analog signal-processing semiconductor that uses high open-loop gain to amplify voltage differences accurately. Within the broader hierarchy, an operational amplifier is a linear amplifier, analog IC, and signal-conditioning component. The LT1013 fits precision instrumentation because its dual configuration supports common differential, summing, filtering, threshold, or transimpedance stages while reducing board area. Verified product information identifies high gain, low noise, low supply current, and a low-offset-voltage temperature coefficient as principal family characteristics. The device can operate from a single 5 V supply, has a common-mode input range that includes ground, and produces output swings to within a few millivolts of ground, as stated in the supplied comparison-source material. These properties are useful in battery-powered measurements where larger supply headroom would be inconvenient. The LT1013 family supports broad supply operation from 4 V to 44 V, allowing the same precision amplifier architecture to serve low-voltage instrumentation and higher-voltage industrial signal chains. Its 1 MHz gain-bandwidth product supports moderate-bandwidth closed-loop functions rather than high-speed waveform or communications applications. The 0.4 V/us slew rate likewise favors low-frequency precision conditioning over wideband pulse acquisition. Analog Devices lists battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, instrumentation amplifiers, 4 mA to 20 mA current-loop transmitters, multiple-limit threshold detection, and active filters as representative LT1013 applications. These uses benefit from dual-channel operation, low supply current, precision behavior, and the ability to work across single and split supplies. When designing with the LT1013CD, preserve the required bypass capacitance, maintain common-mode and output headroom, and confirm that closed-loop bandwidth matches the 1 MHz family characteristic. Check noise, offset, supply current, and common-mode limits against the actual precision requirements. Pricing shown for LCSC is $0.4097 as of 2026-10-22; other distributor prices and current stock must be confirmed at purchase. This page combines verified manufacturer and distributor information, packaging details, applications, pricing context, and engineering guidance. It also identifies which parameters remain unavailable in the supplied evidence instead of estimating them, enabling engineers to make a more defensible LT1013CD selection.

RFQ پەیوەندی
LT1013CJ8 - Dual Precision Op Amp, CDIP | Analog Devices
LT1013CJ8

LT1013CJ8 - Dual Precision Op Amp, CDIP | Analog Devices

The Analog Devices LT1013CJ8 is a dual precision operational amplifier in an 8-pin CERDIP package, with two independent amplifiers and operation from ±15 V or a single 5 V supply. It is specified for input voltages extending to ground on a single supply and for precision signal-conditioning applications where low offset, low bias current, and stable operation across temperature are important. An operational amplifier, or op amp, is a high-gain differential amplifier that uses negative feedback to create a stable closed-loop gain. The LT1013 belongs to the precision amplifier hierarchy: operational amplifier, analog amplifier, and then integrated circuit. Its industry-standard 8-pin configuration supports conventional dual-amplifier layouts without requiring a specialized footprint. The LT1013 provides two precision amplifiers in one package. Key operating characteristics include support for ±15 V supplies, single 5 V operation, and a total supply range extending to ±22 V, corresponding to 44 V across the supply terminals. The device is specified for instrumentation, strain-gauge conditioning, thermocouple amplification, 4 mA-to-20 mA current-loop transmitters, active filters, threshold detection, and precision gain blocks. Its precision architecture is intended to reduce offset-related error in slow analog signals. This makes the amplifier useful where input-source impedance, sensor leakage, or thermal drift can otherwise create measurement errors. The single-supply ability to include ground in the input range is especially useful for battery-powered systems and sensors whose output can approach the lower rail. Typical applications include low-level sensor amplification, process-control instrumentation, current-loop receivers, precision filters, and multiple gain stages requiring two matched amplifier channels. The dual configuration reduces package count in multi-channel analog front ends while retaining independent inputs, outputs, and supply pins. For reliable operation, verify the input and output common-mode range at the selected supply voltage and load. Decoupling capacitors should be placed close to the supply pins, and sensitive bias-current measurements require guarded PCB traces, clean connectors, and leakage control around the input terminals. This page combines the LT1013CJ8 device identity, package information, manufacturer application coverage, verified source links, drop-in-family alternatives, and practical selection guidance for precision analog design work.

RFQ پەیوەندی
LT1013CJG - Dual Precision Op Amp, 300uV Offset, CDIP-8 | Texas Instruments
LT1013CJG

LT1013CJG - Dual Precision Op Amp, 300uV Offset, CDIP-8 | Texas Instruments

The Texas Instruments LT1013CJG is a dual precision operational amplifier with 300 uV maximum input offset voltage, a 0.7 MHz gain-bandwidth product, and a hermetically sealed 8-pin ceramic DIP (CDIP-8) package with 0.300 inch lead pitch. Two amplifiers share one hermetic package, giving instrument-grade amplification in strain-gauge, thermocouple, and 4 mA to 20 mA current-loop signal chains. An operational amplifier (op amp) is a high-gain differential amplifier whose inverting and non-inverting inputs are compared, with feedback defining the closed-loop gain. A precision op amp is a variant optimised for low input offset voltage, low input bias current, and low drift so that small sensor signals are amplified without adding meaningful error. Within the component hierarchy, the LT1013CJG sits as a voltage-feedback amplifier in the family of amplifier ICs, inside the broader class of analog integrated circuits and power-management-adjacent signal-chain devices. Key specifications include a 300 uV maximum input offset voltage, 0.7 MHz gain-bandwidth product, and dual-amplifier configuration in a single hermetic ceramic DIP. The device operates from ±15 V supplies as well as from a single 5 V supply, and it exposes two offset-null pins so that input offset voltage can be trimmed in the circuit rather than accepted as a fixed error. Hermetic ceramic sealing protects the die from moisture and contaminants, which matters in high-reliability and legacy industrial equipment. Architecturally the LT1013CJG is a conventional bipolar voltage-feedback amplifier, which gives it wide supply-voltage swing, low input bias current, and predictable AC behaviour with a single compensation capacitor rather than the auto-zeroed architecture used in chopper-stabilised parts. The result is very low noise at low frequencies with continuous operation across the input range, at the cost of higher offsets than modern auto-zeroed amplifiers. Typical applications include bridge and strain-gauge signal conditioners, thermocouple amplifiers, precision instrumentation amplifiers, 4 mA to 20 mA current-loop transmitters, multiple-limit threshold detection, active filters, and multi-stage gain blocks in battery-powered precision instruments. When designing around this device, use the two offset-null pins for trimming and place the compensation capacitor close to the device. Keep the hermetic package away from thermal sources, because gradient across the ceramic can shift offset voltage, and avoid saturating the output near the supply rails in instrumentation front ends. This page combines manufacturer and distributor technical data, drop-in alternatives, comparison parameters, and practical design guidance that are not consolidated in the original datasheet.

RFQ پەیوەندی
LT1013CP - Dual Precision Op Amp, 4-44V | Texas Instruments
LT1013CP

LT1013CP - Dual Precision Op Amp, 4-44V | Texas Instruments

The Texas Instruments LT1013CP is a dual precision operational amplifier featuring high gain, low supply current, low noise, and a low offset-voltage temperature coefficient, supplied in an 8-pin PDIP (P) package. It operates from a single 4V to 44V supply (or dual ±2V to ±22V supplies), draws only 0.5 mA typical supply current per amplifier, and delivers 150 µV maximum input offset voltage at 25°C (LT1013A grade). The input common-mode range includes ground and the output swings to within a few millivolts of ground while sinking current, eliminating crossover distortion. A dual precision op amp is a two-channel integrated operational amplifier that combines matched transistor pairs and laser-trimmed thin-film resistors to achieve DC accuracy comparable to chopper-stabilized designs while consuming milliwatts of power. Within the broader component taxonomy, dual op amps sit under operational amplifiers -> amplifiers -> analog ICs -> semiconductor. The LT1013 was the first precision dual op amp in the 8-pin industry-standard pinout, upgrading legacy devices such as the MC1458/MC1558, LM158, and OP-221 with significantly lower noise and better DC stability. Key features include 150 µV max input offset voltage (LT1013A) with 2.5 µV/°C max offset voltage temperature coefficient, 0.5 mA typical supply current per amplifier, single-supply operation from 4V to 44V, ground-sensing input range, and output swing to within millivolts of ground. The NPN input stage delivers low input bias current and low voltage noise density suitable for transducer and instrumentation front-ends. Typical applications include battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, 4 mA to 20 mA current-loop transmitters, active filters, multiple limit threshold detection, and instrumentation amplifier building blocks. The wide supply range and ground-sensing inputs make it ideal for single-supply industrial and process-control systems. When designing with this part, observe the input common-mode limit: although the inputs include ground, the upper common-mode limit is approximately 1.5V below the positive rail. Place a 0.1 µF bypass capacitor close to the supply pin and add a 10 µF bulk capacitor on the supply rail to maintain low-impedance power across the LT1013's full bandwidth.

RFQ پەیوەندی
LT1013DD - Dual Precision 5V-44V Op Amp | Texas Instruments
LT1013DD

LT1013DD - Dual Precision 5V-44V Op Amp | Texas Instruments

The Texas Instruments LT1013DD is a low-power dual precision operational amplifier with a 5 V to 44 V wide supply range, two amplifier channels, and an 8-pin SOIC (D) package. The device is intended for instrumentation, signal-conditioning, filtering, and threshold-detection circuits that operate from low single-supply voltages through substantially higher industrial supply levels. Its precision-oriented design combines high gain, low supply current, low noise, and low offset-voltage temperature coefficient, while the extended supply range supports both single-supply and dual-supply implementations. An operational amplifier is an active analog signal-processing device that uses feedback to amplify the difference between its inverting and non-inverting inputs. The dual LT1013 provides two amplifiers in one package, allowing designers to implement two signal paths without using separate packages. In the broader semiconductor hierarchy, the LT1013DD is an analog integrated circuit, specifically a precision operational amplifier used within instrumentation and embedded signal-conditioning systems. The verified product information identifies the LT1013DD as a standard general-purpose dual amplifier with an 8-SOIC package and a 0 °C to 70 °C operating-temperature range. The TI product-page snippet describes the LT1013D as a low-power device with a 5 V to 44 V wide supply range. The wider LT1013 product page states a 4 V to 44 V supply range, so the exact minimum operating supply for the selected LT1013DD ordering option should be confirmed against the manufacturer datasheet before design release. The LT1013DD is suited to battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, instrumentation amplifiers, 4 mA-to-20 mA current-loop transmitters, multiple-limit threshold detection, active filters, and multiple gain blocks. Its dual-channel configuration is useful where two related signals must be conditioned consistently, such as sensor excitation and monitoring or differential and common-reference measurements. Designers should pay particular attention to the SOIC-8 pin mapping, supply bypass capacitors, input common-mode range, output swing, and the operating-temperature limits for this ordering code. The precision characteristics make the device useful for instrumentation, but they do not make it a universal rail-to-rail amplifier. Verify signal levels, noise requirements, load conditions, and stability requirements against the manufacturer datasheet rather than assuming that a substitute is electrically identical. This product page consolidates the verified manufacturer and distributor information, source-backed alternatives, package details, pricing fields, application guidance, and design notes. It is intended to support initial component selection and comparison rather than replace the complete LT1013D datasheet during sign-off.

RFQ پەیوەندی
LT1013DP - Dual Precision Op Amp, 4-44V, 8-PDIP | TI
LT1013DP

LT1013DP - Dual Precision Op Amp, 4-44V, 8-PDIP | TI

The Texas Instruments LT1013DP is a dual precision operational amplifier with a low-power, wide 4 V to 44 V supply range, supplied in an 8-pin PDIP package. The device provides two amplifier circuits in the standard dual-op-amp configuration and is designed for instrumentation and precision signal-conditioning applications. According to the TI product page, the LT1013 family is specified for ±15 V and single 5 V supply operation, while the LT1013D version supports single-supply operation with input voltage range extending to ground and output swing to ground while sinking current. What is a precision operational amplifier? A precision op amp is a voltage-feedback amplifier used to amplify small differential signals while controlling offset, bias current, drift, and output behavior. Within the signal-chain hierarchy, the LT1013DP is a dual amplifier IC that can serve as an instrumentation amplifier building block, a buffer, an active-filter element, or a precision gain stage. Its dual channel count allows two signal paths or a differential signal-conditioning structure in one package. Key verified features include a 4 V to 44 V supply range, dual precision operation, and the industry-standard 8-pin configuration identified by Analog Devices as the first precision dual op amp in that configuration. The LT1013DP is listed by DigiKey as a two-circuit, 8-PDIP amplifier. The Analog Devices product page specifically identifies battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, instrumentation amplifiers, 4 mA to 20 mA current-loop transmitters, multiple-limit threshold detection, active filters, and multiple-gain blocks as application areas. The LT1013DP is especially relevant where a low-power amplifier must operate across a broad supply range or support single-supply signal paths whose input and output approach ground. Compared with a conventional dual precision amplifier in a different package, its 8-PDIP format favors through-hole prototyping, educational platforms, legacy industrial equipment, and repair assemblies where pin compatibility and mechanical replacement matter. The product family is not limited to ±15 V operation; the verified product description confirms single 5 V operation as well. The principal design trade-off is that a PDIP package is larger and less suitable for high-density surface-mount assemblies than a modern small-outline package. Designers should still verify the exact ordering variant, pinout, common-mode limits, output swing, input bias current, offset voltage, drift, noise, and supply-current limits against the manufacturer datasheet before production release. The verified product family is described as low power, but the precise quiescent-current value is not supplied in the provided web data and should be treated as [DATA_NEEDED: quiescent current]. This page synthesizes the verified LT1013 family descriptions, distributor identification, package information, application references, and cross-reference search results. It distinguishes exact verified facts from parameters that require the full manufacturer datasheet, helping engineers evaluate the LT1013DP for precision instrumentation, bridge sensing, thermocouple signal conditioning, current-loop transmission, filtering, and legacy through-hole amplifier designs.

RFQ پەیوەندی