Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
ADM3202ARNZ - 3.3V RS-232 2/2 Transceiver | Analog Devices (Tape & Reel)
The Analog Devices ADM3202ARNZ is a low-power, 2-driver/2-receiver RS-232 line transceiver that operates from a single +3.3 V supply, supports data rates up to 460 kbps, and uses four external 0.1 uF charge pump capacitors, housed in a 16-lead SOIC_N (3.90 mm width) package supplied on tape and reel. An RS-232 transceiver is an interface IC that converts logic-level UART signals (TTL/CMOS, typically 0 V to 3.3 V) into the wider voltage swings specified by the EIA-232E and CCITT V.28 standards, and vice versa. Within the signal chain hierarchy, it belongs to the transceiver class of drivers/receivers under Interface ICs, bridging microcontrollers, processors, or UARTs to legacy serial ports, industrial equipment, and point-of-sale hardware. Key features include single-supply 3.3 V operation with an on-chip charge pump voltage doubler/inverter, conformance to EIA-232E and V.28 specifications, high-speed operation up to 460 kbps, and small 0.1 uF external charge pump capacitors that reduce board area and bill-of-materials cost compared to older parts requiring 1 uF or larger capacitors. Technically, the ADM3202 integrates two charge pump stages (doubler and inverter) to generate approximately +/-6 V RS-232 rails from the 3.3 V supply. The drivers deliver guaranteed EIA-232E output levels, and the receivers include internal input pull-ups so that unconnected receiver inputs default to a known mark state. The ADM3202 variant has no shutdown pin; the related ADM3222 and ADM1385 add a low-power shutdown facility for battery applications. Typical applications include industrial equipment serial ports, embedded systems with RS-232 debug or console links, point-of-sale terminals, battery-powered portable instrumentation (with ADM3222 variants), and any 3.3 V microcontroller design interfacing to legacy RS-232 equipment. Design considerations: place the four 0.1 uF charge pump capacitors as close as possible to the device pins and observe datasheet polarity for the flying capacitors; ensure the supply can support the transient charge pump current during data transmission. This page synthesizes distributor pricing, drop-in alternatives, pinout, and practical design notes not found in a single manufacturer datasheet, as of 2026-09-13.
ADM3202ARNZ-REEL - 3.3V RS-232 2/2 Transceiver | Analog Devices
The Analog Devices ADM3202ARNZ-REEL is a low-power, 2-driver/2-receiver RS-232 line transceiver that operates from a single +3.3 V supply, supports data rates up to 460 kbps, and uses four external 0.1 uF charge pump capacitors, housed in a 16-lead SOIC_N (3.90 mm width) package supplied on tape and reel. An RS-232 transceiver is an interface IC that converts logic-level UART signals (TTL/CMOS, typically 0 V to 3.3 V) into the wider voltage swings specified by the EIA-232E and CCITT V.28 standards, and vice versa. Within the signal chain hierarchy, it belongs to the transceiver class of drivers/receivers under Interface ICs, bridging microcontrollers, processors, or UARTs to legacy serial ports, industrial equipment, and point-of-sale hardware. Key features include single-supply 3.3 V operation with an on-chip charge pump voltage doubler/inverter, conformance to EIA-232E and V.28 specifications, high-speed operation up to 460 kbps, and small 0.1 uF external charge pump capacitors that reduce board area and bill-of-materials cost compared to older parts requiring 1 uF or larger capacitors. Technically, the ADM3202 integrates two charge pump stages (doubler and inverter) to generate approximately +/-6 V RS-232 rails from the 3.3 V supply. The drivers deliver guaranteed EIA-232E output levels, and the receivers include internal input pull-ups so that unconnected receiver inputs default to a known mark state. The ADM3202 variant has no shutdown pin; the related ADM3222 and ADM1385 add a low-power shutdown facility for battery applications. Typical applications include industrial equipment serial ports, embedded systems with RS-232 debug or console links, point-of-sale terminals, battery-powered portable instrumentation (with ADM3222 variants), and any 3.3 V microcontroller design interfacing to legacy RS-232 equipment. Design considerations: place the four 0.1 uF charge pump capacitors as close as possible to the device pins and observe datasheet polarity for the flying capacitors; ensure the supply can support the transient charge pump current during data transmission. This page synthesizes distributor pricing, drop-in alternatives, pinout, and practical design notes not found in a single manufacturer datasheet, as of 2026-09-13.
ADM3202ARNZ-REEL7 - 3.3V RS-232 2/2 Transceiver 460kbps | ADI
The Analog Devices ADM3202ARNZ-REEL7 is a low-power, 2-driver/2-receiver RS-232/V.28 line transceiver that operates from a single +3.3 V supply, supports data rates up to 460 kbps, and uses only four external 0.1 uF charge pump capacitors, housed in a 16-pin SOIC (0.154 in / 3.90 mm width) package supplied on tape and reel. An RS-232 transceiver is an interface IC that converts logic-level UART signals (TTL/CMOS, typically 0 V to 3.3 V) to the higher voltage swings defined by the EIA-232E and ITU V.28 standards, and vice versa. Within the signal-chain hierarchy, it belongs to the interface IC family alongside RS-485, CAN and USB transceivers, and sits between a microcontroller UART and a physical D-sub serial port. Because RS-232 rails can swing to +/-5 V or more, an integrated charge pump (voltage doubler and inverter) is required when only a single low-voltage supply is available. Key features of the ADM3202 include guaranteed 460 kbps operation for high-speed serial links, operation from a 3 V to 5.5 V supply range per distributor parametric data, EIA-232E/V.28 conformance, and a small external capacitor requirement of only 4 x 0.1 uF, which reduces board area and BOM cost. The complementary ADM3222/ADM1385 family members add a low-power shutdown facility for battery-powered portable instruments. Technically, the device uses CMOS charge-pump technology with integrated driver and receiver channels. The charge doubler generates V+ and the inverter generates V- from the 3.3 V rail, enabling true RS-232 output levels without a dual supply. Receivers incorporate hysteresis and tolerate input voltages up to +/-30 V, improving noise immunity on long cables. Typical applications include industrial point-of-sale equipment, networking and communication equipment serial management ports, embedded systems console/debug ports, and battery-powered portable instruments with RS-232 connectivity. Design considerations: place the four 0.1 uF charge pump capacitors as close as possible to pins 1-6, and use at least 0.1 uF of supply decoupling on VCC; note the ADM3202 itself lacks the shutdown pin available on the ADM3222 variant. This page synthesizes distributor availability, drop-in alternatives, pinout detail and design notes beyond what a single datasheet provides.
ADM3202ARUZ - 460 kbps Dual RS-232 Transceiver | Analog Devices
Analog Devices ADM3202ARUZ is a high-speed, 2/2-channel RS-232 interface transceiver with a 460 kbps data rate, a single 3.3 V supply, and four external 0.1 µF charge-pump capacitors. The device is packaged in a 16-pin TSSOP and conforms to the EIA-232E and CCITT V.28 specifications. It combines two RS-232 drivers and two receivers for bidirectional serial-port communication in compact industrial, instrumentation, and embedded systems. An RS-232 transceiver is an interface IC that translates between digital logic levels and the voltage-defined, single-ended signaling used by RS-232 equipment. Within the interface hierarchy, the ADM3202 belongs to the RS-232 transceiver family, a line-interface device within interface ICs and broader semiconductor signal-chain systems. It is intended for equipment that requires standards-compatible electrical levels even when the host controller uses a low-voltage CMOS supply. The ADM3202 family supports data rates up to 460 kbps and is specified at 3.3 V. Its integrated charge-pump circuit generates the positive and negative RS-232 levels from one low-voltage supply, while four external 0.1 µF capacitors support operation of the voltage doubler and inverter. The ADM3202 provides a practical alternative to discrete driver and receiver circuitry where board area, component count, and assembly simplicity are priorities. The device uses 2 transmitters and 2 receivers in a 16-TSSOP package. EIA-232E and CCITT V.28 conformity provides a defined signaling framework for point-to-point serial links. The family also supports several package options, and the ADM3202ARUZ specifically uses the 16-pin TSSOP format. Four external capacitors and the regulated supply must be placed close enough to the charge-pump pins to maintain stable operation and limit switching noise. Typical applications include industrial serial adapters, test and measurement equipment, data-acquisition systems, embedded controllers, point-of-sale terminals, and portable instruments. In each case, the two receivers can accommodate two incoming RS-232 signals while the two drivers produce two outgoing signals. The 460 kbps capability is suitable for substantially faster communication than conventional low-speed serial-console links, while operation from 3.3 V simplifies integration with modern control electronics. The primary design consideration is charge-pump capacitor placement. Use the specified 0.1 µF capacitors on the designated pins and maintain a short, direct return path to the device ground. Designers should also preserve the RS-232 driver output levels at the connector and account for the unidirectional nature of individual RS-232 lines when assigning driver and receiver channels. This product overview combines the manufacturer specifications, package details, replacement considerations, interface guidance, and practical application analysis needed to evaluate the ADM3202ARUZ for a new design or an existing 16-TSSOP RS-232 interface.
ADM3202ARW - Dual 3.3V RS-232 Transceiver | Analog Devices
The Analog Devices ADM3202ARW is a dual-channel RS-232 line driver and receiver operating from a single 3.3 V supply in a 16-pin SOIC package. The device supports two transmit channels and two receive channels, conforms to EIA-232E and CCITT V.28 requirements, and operates at data rates up to 230 kbps according to the manufacturer product page. Four external 0.1 µF charge-pump capacitors support the integrated voltage doubler and inverter. An RS-232 transceiver is an interface IC that converts logic-level signals to RS-232 line levels and converts incoming RS-232 signals back to digital logic. In the signal-chain hierarchy, the ADM3202ARW is a dual RS-232 interface transceiver, placing it within interface ICs, communication semiconductors, and broader industrial and embedded control systems. It is useful where a host, instrument, controller, or service port must communicate with legacy RS-232 equipment over a single 3.3 V power rail. Key features include two RS-232 drivers and two RS-232 receivers, operation from a single 3.3 V supply, and support for data rates up to 230 kbps. The four external 0.1 µF charge-pump capacitors simplify implementation of the on-chip voltage generation network. The wide SOIC package supports conventional surface-mount assembly, while its dual-channel arrangement reduces the component count compared with using separate single-channel line-driver and receiver devices. The ADM3202ARW uses charge-pump circuitry to develop the voltage levels required by RS-232 from one low-voltage supply. This architecture suits portable and low-voltage equipment where a 5 V rail is undesirable or unavailable. The EIA-232E and CCITT V.28 conformance provides defined electrical behavior for point-to-point serial links, while the maximum 230 kbps operating rate supports substantially faster communication than commonly required by legacy serial equipment. Typical uses include industrial serial adapters, test and measurement instruments, point-of-sale terminals, embedded controllers, diagnostic consoles, and portable equipment with RS-232 connectivity. The dual-driver, dual-receiver configuration can support either two independent RS-232 links or a split communication arrangement when the system has limited connector or interface resources. The low 3.3 V operating supply also suits battery-powered and portable industrial designs. Place the four 0.1 µF charge-pump capacitors close to their designated pins and route the RS-232 driver and receiver traces away from sensitive clock, sensor, and analog inputs. Confirm the system’s supply tolerance, line-driver load, receiver threshold, and grounding strategy against the manufacturer datasheet before layout release. External protection may also be required when the cable can be exposed to electrostatic discharge or surge conditions outside the device's specified operating environment.
ADM3222AN - 460 kbps Dual RS-232 Transceiver | Analog Devices
The Analog Devices ADM3222AN is a dual-channel RS-232/V.28 interface transceiver rated for data rates up to 460 kbps, operating from a single 3.3 V supply in an 18-pin PDIP package. The device combines two RS-232 line drivers with two receivers, supports low-power shutdown and enable control, and uses four external 0.1 µF charge-pump capacitors to generate the bipolar voltage required by RS-232. An RS-232 transceiver is an interface IC that converts between digital logic levels and the voltage levels used by RS-232 serial links. It belongs to the broader communications-interface hierarchy: RS-232 transceiver → serial-interface IC → interface IC → semiconductor. Such devices bridge UART, UART-over-RS-232, or legacy peripheral ports to cables and equipment using balanced differential signaling. Key features include operation at 460 kbps, compliance with EIA-232E and CCITT V.28 specifications, a 3.3 V single-supply architecture, and ESD protection specified to IEC 1000-4-2. The ADM3222 adds enable and shutdown circuitry for systems where the interface must be placed into a low-consumption state. Its two transmitters and two receivers make it suitable for consolidating two serial channels onto one device. The on-chip charge-pump circuit uses four external 0.1 µF capacitors to develop positive and negative voltage rails for the RS-232 drivers. This architecture permits operation without a dual supply and reduces system complexity. EIA-232E and CCITT V.28 conformance support interoperability with conventional RS-232 equipment, while the 460 kbps maximum data rate provides more bandwidth than the slower legacy communication rates commonly associated with older RS-232 ports. Typical applications include industrial serial-port expansion, instrumentation interfaces, point-of-sale equipment, data acquisition systems, and legacy peripheral connections that must be retained alongside newer low-voltage digital circuitry. The enable and shutdown controls are particularly useful in battery-powered portable instruments where inactive interface current matters. Circuit implementation requires careful capacitor placement near the charge-pump pins, short RS-232 traces, and protection appropriate to the cable environment. Confirm that the host logic levels and selected UART baud rate are compatible with the 3.3 V interface and 460 kbps device capability. This page consolidates interface specifications, application guidance, design considerations, and practical sourcing information for engineers evaluating the ADM3222AN in compact RS-232 implementations.
ADM3222ANZ - 460 kbps 3.3 V RS-232 Transceiver | Analog Devices
Analog Devices ADM3222ANZ is a two-channel RS-232 transceiver with one driver and one receiver per channel, a maximum data rate of 460 kbps, and a single 3.3 V supply. The device is offered in an 18-pin PDIP package and includes low-power shutdown and enable control. Four external 0.1 µF charge-pump capacitors support its on-chip voltage-doubler and inverter functions. An RS-232 transceiver is an interface IC that translates logic-level signals into RS-232-compatible line levels and converts received line signals back into digital logic. In the broader semiconductor hierarchy, the ADM3222ANZ belongs to the interface IC family and connects host controllers or programmable logic to serial equipment using the EIA-232E and CCITT V.28 signaling conventions. Key features include a 460 kbps data rate, operation from a single 3.3 V supply, two transmit and two receive channels, 0.1 µF charge-pump capacitors, and low-power shutdown. The Analog Devices ADM3222 datasheet also identifies enhanced ESD protection to IEC 1000-4-2. These characteristics make the device suitable for industrial control links, portable equipment, data acquisition systems, and embedded serial ports that require a compact multi-channel RS-232 interface. The internal charge-pump topology generates the positive and negative voltages required by RS-232 from the single low-voltage supply. Four external capacitors are required for the voltage doubler and inverter, while the enable and shutdown circuitry supports controlled power management. Because the interface maintains separate transmit and receive channels, two RS-232 ports can be implemented in a compact system. Typical uses include configuration interfaces for industrial equipment, service and control ports on test systems, communication links between embedded controllers and legacy peripherals, and isolated or multi-port data acquisition equipment. The 460 kbps capability provides ample margin for common asynchronous serial protocols when the attached equipment supports the corresponding line rate. PCB implementation should place the four charge-pump capacitors close to their associated device pins and preserve the recommended routing around the RS-232 driver outputs. Confirm line protection, cable length, ground-reference strategy, and signal-integrity requirements at the connector because logic-level specifications alone do not determine reliable behavior over an external RS-232 cable. This product overview organizes the ADM3222ANZ electrical capabilities, package information, sourcing details, interface applications, and design guidance into one engineering reference. It also distinguishes verified drop-in alternatives from parts that differ in package, data rate, supply voltage, or shutdown behavior.
ADM3222ARU - 3.3V Dual RS-232 Transceiver | Analog Devices
Analog Devices ADM3222ARU is a dual-channel RS-232 transceiver with two drivers and two receivers, operating from a single 3.3 V supply at data rates up to 230 kbps and housed in a 20-lead TSSOP package. The device conforms to the EIA-232E and CCITT V.28 specifications, making it suitable for legacy serial-port equipment, industrial control links, and portable data-acquisition systems. An RS-232 transceiver is an interface IC that converts logic-level transmit and receive signals into RS-232 line levels and converts incoming RS-232 signals back into CMOS-compatible logic. Within the interface hierarchy, the ADM3222ARU is an RS-232 transceiver, a serial-interface IC, and ultimately a general-purpose semiconductor. Its integrated voltage-doubling and inverter charge-pump circuitry eliminates a separate bipolar power supply when the system already has 3.3 V power. Key features include two transmit channels, two receive channels, operation from one 3.3 V supply, external 0.1 µF charge-pump capacitors, and integrated enable and shutdown circuitry. The charge-pump approach supports portable and battery-operated equipment by avoiding external RS-232 line-power generation. The interface is intended for data rates up to 230 kbps according to the Analog Devices product page. The ADM3222 receives and transmits through its charge-pump-generated RS-232 levels, while the enable and shutdown functions provide control over operating state. Four external 0.1 µF capacitors are required for the voltage doubler and inverter. The device is also described as an upgrade path for MAX3222 and MAX3232 designs, with enhanced electrostatic-discharge protection rated to IEC 1000-4-2. Typical applications include industrial serial adapters, portable test equipment, point-of-sale terminals, instrument-control links, and embedded systems that retain an RS-232 port for compatibility with legacy peripherals. Its single 3.3 V supply is especially useful where a modern controller operates from 3.3 V and adding positive and negative RS-232 rails would increase design complexity. Place all four 0.1 µF charge-pump capacitors close to their designated pins, keep the RS-232 signal traces away from sensitive analog or high-speed digital paths, and provide local supply decoupling near the device. Confirm the transmitter output levels and receiver thresholds at the system interface because cable length, grounding, and ESD exposure determine whether additional protection or isolation is required. This page combines the manufacturer's electrical specifications with package-level guidance, interface applications, verified cross-references, and practical layout considerations for engineers evaluating the ADM3222ARU or planning a pin-compatible replacement.
ADM3222ARWZ - 230kbps 3.3V RS-232 Transceiver | Analog Devices
The Analog Devices ADM3222ARWZ is a two-driver, two-receiver RS-232 transceiver designed for 3.3 V single-supply operation, with data rates up to 230 kbps in an 18-lead SOIC package. Its integrated charge-pump circuitry supports EIA-232E and CCITT V.28 interfaces while reducing the external component count. An RS-232 transceiver is a semiconductor interface that converts logic-level signals into RS-232 line levels and receives RS-232 signals back into logic-compatible levels. It belongs to the interface IC hierarchy, connecting UART, UART-over-USB, and embedded systems to legacy RS-232 equipment. The ADM3222ARWZ provides bidirectional conversion through two driver channels and two receiver channels. Principal features include operation from a single 3.3 V supply, low-power shutdown circuitry, four external 0.1 µF charge-pump capacitors, and support for portable instrumentation. The manufacturer product page specifies data rates up to 230 kbps. One distributor specification listing also identifies a 3 V to 5.5 V supply range, allowing the interface to operate across common low-voltage systems. The charge-pump voltage doubler and inverter generate the bipolar voltage required by RS-232 from one low-voltage supply. Four external capacitors stabilize these rails, while the receiver channels translate the remote line voltage into CMOS-compatible signals. The separate transmit and receive channels permit simultaneous full-duplex operation on two ports. Typical uses include battery-powered portable instruments, industrial data-acquisition equipment, point-of-sale terminals, service interfaces, and embedded systems that must communicate with RS-232 equipment. The 18-lead SOIC package is suitable for compact surface-mounted assemblies requiring two RS-232 ports. PCB design must reserve the four charge-pump capacitor connections and place the capacitors close to their associated pins. A solid ground plane, short return paths, and controlled routing of exposed RS-232 cable-side nets help reduce radiated emissions and susceptibility to external interference. This page combines interface specifications, application guidance, pin-compatible family options, and design notes to support component selection, schematic review, PCB implementation, and sourcing decisions for the ADM3222ARWZ.
ADM3251EARWZ - 2.5kV Isolated RS-232 Transceiver, 460kbps | ADI
The Analog Devices ADM3251EARWZ is a 2.5 kV rms fully isolated, single-channel RS-232/V.28 transceiver housed in a 20-pin SOIC (7.5 mm body width) wide-body package with integrated isoPower dc-to-dc converter. It operates from a single 5 V supply, supports data rates up to 460 kbps, and delivers 25 kV/µs common-mode transient immunity (CMTI) across the reinforced isolation barrier. An RS-232 transceiver is a line interface IC that converts CMOS/TTL logic levels (0-5 V) into EIA/TIA-232E voltage swings (±5 V to ±15 V) required by legacy serial-port peripherals such as industrial PLCs, point-of-sale terminals, and instrumentation. A fully isolated variant such as the ADM3251EARWZ adds galvanic isolation (here 2.5 kV rms) between the logic-side UART and the cable-side driver/receiver, breaking ground loops and protecting low-voltage MCUs from large common-mode transients and ESD events on the bus. Key specifications include ±15 kV ESD protection (HBM) on the RIN and TOUT pins, integrated charge-pump that requires only four external 0.1 µF capacitors, low-power shutdown mode, and an exposed pad for thermal dissipation. The chip conforms to EIA/TIA-232E and ITU-T V.28 standards, ensuring interoperability with any standard RS-232 host or peripheral. Architecturally, the device combines an iCoupler digital-isolation data path with an isoPower transformer-based DC-DC converter that derives the ±RS-232 supplies internally, eliminating the need for a separate isolated supply on the cable side. This single-chip isolation approach reduces PCB area versus discrete isolator-plus-transceiver designs and simplifies regulatory compliance for medical, industrial, and renewable-energy systems. Typical applications include isolated serial ports in PLCs and motor drives, point-of-sale terminals, medical patient monitors, solar inverter diagnostics, and any RS-232 link requiring robust ground-loop immunity. When designing with this device, allocate the four 0.1 µF charge-pump capacitors close to the V+ and V- pins, and provide a low-ESR decoupling cap on VDD. Verify creepage and clearance on the PCB to maintain the 2.5 kV rms rating. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet.
ADM3483ARZ - 3.3V 250kbps RS-485 Transceiver | Analog Devices
The Analog Devices ADM3483ARZ is a 3.3 V, low-power, half-duplex RS-485/RS-422 transceiver rated for data rates up to 250 kbps and housed in an 8-pin SOIC package. It combines one differential driver and one differential receiver with separate driver-enable and receiver-enable control, making it suitable for multipoint industrial communication networks. Its slew-rate-limited outputs reduce electromagnetic interference, while shutdown operation supports systems that need a low-power state. An RS-485 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over longer cables and noisy environments. The RS-485/RS-422 transceiver category belongs to the broader interface-IC hierarchy and enables multiple nodes to share a two-wire bus while improving noise immunity, grounding flexibility, and common-mode tolerance compared with single-ended signaling. The ADM3483ARZ operates from a single 3.3 V supply and supports the standard low-power 3.3 V operating range of 3.0 V to 3.6 V. Key features include a maximum data rate of 250 kbps, reduced slew rates for low EMI, and support for as many as 32 transceivers on one bus. The device also tolerates bus voltages up to +12 V according to the product description. The half-duplex architecture allows the same differential pair to carry transmitted or received data, but only one direction can be active at a time. Driver-enable and receiver-enable inputs provide local control of bus direction and receiver state. This arrangement reduces external interface logic when a connected microcontroller or host controller needs to switch between driving a command and listening for a response. Typical applications include industrial automation controllers, building-automation equipment, remote sensor interfaces, instrumentation links, and low-power embedded communications modules. A 250 kbps rate is appropriate for moderate-speed control and monitoring rather than high-bandwidth factory protocols. The device is particularly useful where low EMI, a 3.3 V supply, and multipoint bus capability matter more than maximum line rate. Design the bus with a symmetric differential trace geometry, controlled impedance, proper termination, and a common-mode strategy appropriate to the installation. Keep transceiver and connector ground references consistent, and account for cable delay when determining whether the selected data rate is safe for the total bus length. This page combines manufacturer specifications, drop-in replacement information, interface-design guidance, and application-focused comparisons to support component selection and PCB implementation beyond the basic ordering information.
ADM3485EAN - 3.3V 20Mbps RS-485/422 Transceiver | ADI
Analog Devices ADM3485EAN is a 3.3 V low-power RS-485/RS-422 differential data transceiver with a maximum data rate of 20 Mbps, 15 kV ESD protection, and an 8-pin SOIC package. It is designed for balanced, half-duplex communication over multipoint bus transmission lines and provides integrated driver and receiver functions for industrial, communications, and instrumentation systems. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over longer cables. A differential receiver rejects common-mode noise, while the transceiver family connects equipment through bidirectional bus wiring. The ADM3485E belongs to the broader line-driver and receiver hierarchy within interface ICs, providing physical-layer signaling for multipoint networks. Key features include operation from a 3.3 V supply, a 20 Mbps maximum data rate, 15 kV ESD protection, and compliance with TIA/EIA RS-422 and RS-485 standards over the full common-mode range. The device supports half-duplex operation and a 19 kΩ input impedance, allowing up to 19 transceivers on a bus. Low-power operation is important in distributed equipment because each node continuously contributes to the total bus loading. The ADM3485E architecture combines a differential driver, differential receiver, driver-enable control, and receiver-enable control in one package. Driver and receiver enables support directional control on half-duplex networks. Short-circuit protection improves robustness when a bus driver drives into a fault condition, while the specified ESD protection helps protect the transceiver pins during handling and cable-side transients. Typical applications include industrial RS-485 buses, building and factory automation networks, instrumentation links, industrial gateways, and embedded communications equipment. The 20 Mbps capability supports high-speed short-distance links, while the balanced interface and 19 kΩ input impedance are useful when multiple nodes share a bus. External protection may still be required for severe industrial surge environments. For PCB design, place the transceiver close to the connector and bus interface, keep differential traces closely coupled, and provide the bypass capacitance and termination required by the bus topology. Avoid adding excessive capacitance to driver and receiver inputs. Do not substitute the RS-422 and RS-485 termination or biasing arrangements without checking the bus configuration. This product page combines the Analog Devices device description, package information, cross-reference candidates, practical bus-design guidance, and parameter-level comparisons to simplify transceiver selection and PCB implementation.
ADM3485EAR - 12 Mbps 3.3 V RS-485 Transceiver | Analog Devices
The Analog Devices ADM3485EAR is a 3.3 V, low-power RS-485/RS-422 half-duplex transceiver rated for data rates up to 12 Mbps, with ±15 kV ESD protection on the RS-485 input and output pins. The device is packaged in an 8-pin SOIC and supports balanced differential communication on multipoint bus transmission lines. One transmitter and one receiver are integrated into each package, allowing a compact two-wire industrial communications interface. An RS-485 transceiver is an interface IC that converts logic-level serial data into balanced differential signals for reliable communication over longer cables and noisy environments. The corresponding receiver converts differential bus voltage back into a logic-level signal. Together, these devices form the physical-layer link between a controller and remote nodes, with RS-422 providing balanced point-to-point signaling and RS-485 supporting multipoint buses. Key features include TIA/EIA RS-485 and RS-422 compliance, a maximum data rate of 12 Mbps, ±15 kV ESD protection, and operation on a single 3.3 V supply. The half-duplex configuration shares the driver and receiver bus connections, reducing board area and external switching requirements. A fail-safe receiver is designed to provide a defined output when the bus is open-circuit, while the low-power shutdown function supports systems that need to reduce consumption when the interface is inactive. The ADM3485E family combines a low-power 3.3 V architecture with high-speed differential signaling. Its 12 Mbps capability suits short-distance, high-speed industrial links, while multipoint operation accommodates systems with as many as 32 nodes. The 8-pin SOIC package supports conventional surface-mount assembly, and the same compact footprint simplifies comparison with other 8-pin half-duplex line transceivers. Typical uses include industrial control networks, factory automation equipment, instrumentation, motor-control subsystems, and embedded serial buses. The device can also serve as a robust physical-layer interface between a host controller and remotely located sensors, actuators, or data-acquisition modules where 3.3 V logic levels and multidrop capability are required. Designers should preserve the transceiver's common-mode range and termination requirements when laying out the bus. Place the differential line pair with continuous ground reference, route the pair as a coupled transmission-line structure, and position termination only at designated bus endpoints. Add suitable surge protection and verify that system grounding and cable length remain compatible with the operating data rate. This page combines electrical characteristics, package details, application guidance, parameter comparisons, and verified drop-in alternatives. It also highlights design trade-offs involving data rate, bus direction control, ESD protection, termination, and multipoint operation so engineers can select the correct interface IC before layout begins.
ADM3488ARZN - 250 kbps Full-Duplex RS-485 Transceiver | Analog Devices
The Analog Devices ADM3488ARZN is a 3.3 V, low-power differential line transceiver with a maximum data rate of 250 kbps, full-duplex RS-485/RS-422 operation, slew-rate-limited signaling, and an 8-pin SOIC package. It combines one differential driver and one differential receiver in a single package, making it suitable for bidirectional industrial communication links that require low power and controlled edge rates. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable transmission over longer cable runs. The differential signaling improves noise immunity by comparing the voltage between two conductors rather than referencing the signal to ground. In the system hierarchy, the ADM3488 belongs to interface ICs, line transceivers, physical-layer communication devices, and ultimately semiconductor components. The ADM3488 family operates from a single 3.3 V supply, emphasizing low power consumption for industrial, instrumentation, and embedded systems. Its 250 kbps maximum signaling rate supports moderate-speed data rather than the multi-megabit rates used by high-speed RS-485 links. The slew-rate-limited driver reduces high-frequency harmonics and ringing on long cables, improving electromagnetic compatibility without requiring a higher data rate. Analog Devices identifies the ADM3488 as a production full-duplex RS-485/RS-422 transceiver. The 8-SOIC format supports conventional surface-mount assembly and is smaller than many older leaded interface packages. Because the device supports full-duplex communication, the driver and receiver paths can operate simultaneously, allowing dedicated transmit and receive pairs on a bus design. Typical uses include industrial automation equipment, motor controllers, test and measurement instruments, building automation interfaces, and embedded serial links. The controlled transition rate is especially useful where cable length, ringing, or emissions must be managed. Applications that need greater bus speed, galvanic isolation, automatic direction control, or integrated termination should be evaluated against devices designed for those specific functions. PCB implementation should preserve the differential path from the transceiver to the connector and minimize stubs. Place the interface IC near the connector and route the differential pair as a tightly coupled pair over a continuous reference plane. Decoupling capacitance must be positioned close to the supply pins, while external protection components should be selected to handle the cable-side voltage and surge environment. This product page combines device specifications, pin-compatible replacement guidance, application analysis, and practical PCB considerations. It helps engineers distinguish the ADM3488 from half-duplex transceivers, electrically similar but pin-incompatible interface ICs, and higher-speed or enhanced-protection alternatives before committing a board design.
ADM3490ARZ - 10Mbps RS-485/422 Transceiver | Analog Devices
The Analog Devices ADM3490ARZ is a 3.3 V differential line transceiver supporting RS-485 and RS-422 operation at data rates up to 10 Mbps, with one driver and one receiver in an 8-pin SOIC package. Its reduced-slew-rate design lowers electromagnetic interference while maintaining the throughput required for industrial communication links. The device also supports 5 V logic interoperability and operates across the full common-mode range specified for EIA RS-422 and RS-485 networks. A differential line transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable transmission over noisy interconnects. The ADM3490ARZ belongs to the RS-485/RS-422 transceiver hierarchy, combining a line driver, a differential receiver, and an interface supply in one device. Balanced signaling improves noise immunity by rejecting common-mode voltage, while the receiver reconstructs the intended logic state from the difference between two signal conductors. The principal features include operation from a single 3.3 V supply, a maximum data rate of 10 Mbps, reduced slew rates for low EMI, half- and full-duplex family options, and interoperability with 5 V logic. Its receiver input impedance is 12 kΩ, allowing up to 32 transceivers on a bus. A shutdown function supports low-power operation, while thermal-shutdown protection helps prevent excessive internal heating from sustained fault conditions. The ADM3490ARZ is designed around a differential driver and differential receiver suitable for point-to-point, multipoint, and multidrop RS-485 networks. The reduced edge rate spreads high-frequency energy more broadly and reduces ringing and radiated emissions compared with an unrestricted 10 Mbps edge rate. Logic-compatible receiver output and driver input interfaces simplify connection to 3.3 V controllers while permitting interoperability with systems containing 5 V logic. Typical applications include industrial automation, factory equipment, building controls, instrumentation links, and embedded RS-485 networks. It is particularly useful when a design needs more speed than the 250 kbps ADM3483 and ADM3488 class while retaining reduced-slew-rate behavior for electromagnetic compatibility. The SOIC-8 footprint also supports conventional surface-mount assembly and copper-based thermal dissipation. For robust bus implementation, place the transceiver close to the connector and route the differential pair as a tightly coupled trace over a continuous reference plane.Termination, biasing, and protection components should be placed where they can be changed or inspected without disturbing the signal pair. The manufacturer datasheet should be used to confirm the exact pin assignments, input thresholds, timing limits, and bus loading conditions for the selected system. This page combines the manufacturer's device characteristics with practical interface guidance, a parameter-focused comparison against same-footprint alternatives, and design notes for PCB routing, termination, and fault protection. These engineering details help distinguish a genuinely drop-in replacement from a transceiver that is only functionally similar but incompatible with the existing ADM3490ARZ footprint.
ADM3491AN - 3.3V 20Mbps RS-485 Transceiver | Analog Devices
The Analog Devices ADM3491AN is a 3.3 V, full-duplex differential line transceiver capable of 20 Mbps data rates, with 840 µA supply current and a 12-pin PDIP package. Designed for multipoint transmission lines, it supports EIA RS-485 and RS-422 communication while providing short-circuit protection, thermal shutdown, and interoperability with 5 V logic. An RS-485 transceiver is an interface integrated circuit that converts logic-level signals into balanced differential signals for reliable communication over longer cables and electrically noisy environments. The differential signaling method improves noise immunity by comparing the two conductors rather than relying on a single-ended voltage. The ADM3491AN belongs to the RS-485 transceiver category, where it combines a transmitter, receiver, and bus-driver circuitry in one low-power device for industrial and embedded data links. Low power consumption is central to the ADM3491AN design. Its 840 µA operating supply current suits battery-powered and power-sensitive instruments, while the shutdown mode reduces supply current to 2 nA. A 20 Mbps maximum data rate supports high-speed point-to-point or multipoint links, and the receiver input impedance of 19 kΩ permits up to 50 transceivers on a bus. Interoperability with 5 V logic allows the device to connect to controllers operating above its nominal 3.3 V supply level. The ADM3491 family provides a combination of low-power operation, common-mode range, and transient robustness. Analog Devices specifies operation with a 3.3 V supply across a ±0.3 V tolerance. Its electrical characteristics are specified over the full device temperature range, and the integrated thermal shutdown mechanism provides protection when the output driver is subjected to fault conditions. An 8 ns transmitter skew specification helps preserve timing relationships between complementary differential outputs. Typical uses include industrial RS-485 links, instrumentation equipment, building controls, factory automation networks, and low-power embedded communications. The device is particularly appropriate where a compact multipoint bus must operate from a 3.3 V supply and where low standby current matters. Its transmitter can also be used in full-duplex point-to-point configurations when separate differential pairs are available. The principal design consideration is that the 12-pin PDIP package occupies more board area than leadless surface-mount alternatives. Place the transceiver close to the connector and bus interface, maintain the differential pair as a tightly coupled route, and provide the termination and biasing required by the RS-485 network. Keep the logic side and cable-side return paths separated to avoid introducing ground potential differences into the differential receiver. This page combines the manufacturer's key electrical ratings with practical guidance for RS-485 bus implementation, package selection, transient protection, and power management. It also identifies the temperature-grade ADM3491AN-1 as a same-package option for design continuity when its specified operating grade matches the system requirements.
ADM3491AN-1 - 3.3V 20Mbps RS-485/RS-422 Transceiver | Analog Devices
The Analog Devices ADM3491AN-1 is a low-power differential line transceiver operating from a single 3.3 V supply, with a maximum data rate of 20 Mbps in a 14-lead SOIC package. It combines a differential line driver and differential line receiver for balanced RS-485 and RS-422 communication, while a shutdown mode helps reduce consumption in power-sensitive systems. A differential line transceiver is an interface IC that transmits data across balanced, noise-resistant lines while receiving signals with high common-mode rejection. RS-485 supports robust multipoint communication over relatively long cable runs, whereas RS-422 emphasizes full-duplex point-to-point links. Within the interface hierarchy, the ADM3491AN-1 belongs to the RS-485/RS-422 transceiver class, connects digital controllers to physical communication lines, and operates as part of a broader industrial communications system. Key features include a single 3.3 V power supply, low-power operation, full-duplex communication, and a shutdown function. The identified low-power figure is 840 uA, while the cited data rate reaches 20 Mbps. Its differential driver and receiver architecture provides a practical balance between communication throughput, power consumption, and system complexity. The separate driver and receiver paths support simultaneous transmission and reception in full-duplex RS-422 networks. The ADM3491 family is intended for balanced data transmission and supports both Electronic Industries Association RS-485 and RS-422 interfaces. Communication protocols can use the transceiver as the physical-layer interface beneath UART, industrial automation, instrumentation, or industrial Ethernet equipment. The 3.3 V supply also allows direct integration with modern low-voltage controllers, reducing the need for level-shift or separate line-driver circuitry. Typical uses include industrial control links, factory automation nodes, sensor and instrumentation networks, building-control equipment, and data-acquisition systems. In these applications, the balanced line helps reject common-mode noise encountered near motors, relays, and long cables. The 20 Mbps capability is useful for links that require higher throughput than conventional low-speed RS-485 nodes while retaining the simplicity of a serial differential interface. PCB design should preserve the differential signal path, use a continuous ground reference, and place termination and protection components near the line interface. The shutdown control should be driven only after the transmitter and receiver signals are placed in a safe state. Operating temperature, enable polarity, receiver fail-safe behavior, and electrical limits should be confirmed against the manufacturer datasheet before production release. This page combines the device function, verified operating characteristics, package information, interface-design guidance, and comparison criteria for evaluating the ADM3491 family against compatible interface transceivers.
ADM3491ARZ - 3.3V Full-Duplex RS-485/RS-422 | Analog Devices
The Analog Devices ADM3491ARZ is a low-power differential line transceiver designed for operation from a single +3.3 V power supply. It supports 10 Mbps data rates, full-duplex RS-422 and RS-485 communication, 5 V logic interoperability, short-circuit protection, and a low 840 µA supply current. The device is offered in a 14-lead SOIC package for industrial data links and multipoint transmission systems. A differential line transceiver is an interface integrated circuit that combines a transmitter and receiver to communicate over balanced, differential pairs. RS-422 is commonly used for point-to-point links, while RS-485 supports multipoint buses. These standards belong to the broader wired-data-interface hierarchy, where transceivers connect low-voltage digital logic to external cables carrying larger-amplitude differential signals. Key features include a 3.3 V operating supply, 10 Mbps maximum signaling rate, 19 kΩ receiver input impedance, and support for up to 50 transceivers on a bus. The receiver remains compatible with 5 V logic, which simplifies interfaces between newer 3.3 V systems and older digital controllers. A shutdown mode reduces supply current to 2 nA, making the device suitable for power-sensitive systems that are intermittently active. The ADM3491 family provides EIA RS-422 and RS-485 compliance across the full common-mode range. Its 8 ns transmit skew supports balanced timing between differential outputs, while reduced slew rates on related family members address electromagnetic-interference requirements. Short-circuit protection and thermal shutdown improve robustness when a driver encounters an abnormal bus condition. Typical uses include industrial automation links, data acquisition equipment, building-control systems, instrumentation, and communications equipment requiring a full-duplex balanced interface. The 10 Mbps capability is appropriate for factory-floor links, while the 19 kΩ input impedance permits multiple receivers on a bus without excessive loading. PCB design should preserve the differential signal path and provide a controlled return route. Place input and output bypassing capacitors close to their associated supply pins, and keep connector and protection-device return currents from crossing the differential pair. Confirm the exact pin names and exposed connections in the manufacturer datasheet before assigning PCB nets. This page combines application guidance, engineering design notes, and structured cross-reference information to support faster transceiver selection and board bring-up. The ADM3491ARZ is suited to engineers who need a compact, low-power, 3.3 V full-duplex RS-422 or RS-485 interface with 10 Mbps operation.
ADM483ARZ - 250 kbps RS-485/RS-422 Transceiver | Analog Devices
The Analog Devices ADM483ARZ is a 5 V, slew-rate-limited, low-power half-duplex differential line transceiver rated for 250 kbps data rates and packaged in an 8-pin SOIC. It supports RS-485 and RS-422 communication over multipoint buses, combining a differential line driver and differential receiver in one package. Key operating characteristics include a 5 V supply, 250 kbps maximum signaling rate, 120 uA low-power consumption, and a -7 V to +12 V bus common-mode range. An RS-485/RS-422 transceiver is an interface IC that converts logic-level transmit and receive signals into balanced differential signals suitable for reliable communication over wired buses. RS-485 supports multipoint, half-duplex networks, while RS-422 provides a differential signaling foundation for point-to-point links. The ADM483 belongs to the broader interface IC hierarchy alongside UARTs, isolated transceivers, CAN transceivers, and other wired-communication interface devices. The ADM483’s principal feature is its controlled slew rate. Slowing the driver edge rate reduces electromagnetic interference and ringing on slow or terminated cabling while preserving operation at up to 250 kbps. The device also supports high-impedance driver output when disabled or powered off, thermal shutdown, and short-circuit protection. These characteristics are useful in industrial equipment, building controls, and instrumentation where cable length, grounding, and reflected signals can affect reliability. The receiver operates across a -7 V to +12 V common-mode range, allowing the bus pins to tolerate significant differential signal offset without immediately losing receiver function. Up to 32 transceivers can share one bus according to the Analog Devices data sheet. The ADM483ARZ is specified from -40°C to +85°C, making it suitable for industrial temperature environments when the wider commercial operating range is insufficient. Typical uses include RS-485 instrument buses, factory-floor controllers, remote sensor nodes, building automation equipment, and RS-422 links between a controller and a peripheral. In a half-duplex design, the driver and receiver paths share the same pair of bus conductors, so the DE and RE controls must be coordinated to avoid contention. The low 120 uA supply current also benefits compact systems where bus-node power consumption affects the overall power budget. For implementation, follow the manufacturer’s recommended decoupling and termination arrangement. Place the supply capacitor close to VCC, connect the differential pair with tightly matched routing, and apply termination only where the cable topology requires it. Confirm driver-enable timing, bus-idle state, grounding strategy, and fault behavior before releasing the transceiver into a live multidrop network. This product page combines the ADM483ARZ operating limits, interface behavior, package information, and application guidance with drop-in replacement analysis. The comparison table highlights electrical and mechanical trade-offs so engineers can select a replacement based on verified similarity rather than package name alone.
ADM483EAR - 250 kbps RS-485 Transceiver | Analog Devices
Analog Devices ADM483EAR is a low-power, slew-rate-limited RS-485/RS-422 half-duplex transceiver rated for 250 kbps data transmission, supplied from a single 5 V rail and offered in an 8-pin SOIC package. The device combines one differential driver and one differential receiver, supports balanced multipoint bus communication, and provides ±15 kV ESD protection on its bus-facing pins. Its reduced slew rate is intended to limit electromagnetic interference on long or poorly terminated interconnects. An RS-485 transceiver is an interface IC that converts logic-level serial data into a differential physical signal for communication over balanced cabling. It belongs to the transceiver hierarchy within RS-485 and RS-422 interface ICs, where a differential driver transmits logic states onto a twisted-pair bus and a differential receiver converts the returning differential signal into CMOS-compatible logic. The ADM483EAR is designed for half-duplex systems in which the same pair of conductors carries data in either direction, but only one transmitter is active at a time. The ADM483EAR supports operation from a single 4.5 V to 5.5 V supply, a 250 kbps maximum signaling rate, and a ±12 V common-mode range on the bus. These characteristics make it appropriate for industrial equipment, building controls, instrumentation, and embedded systems using balanced multipoint buses. Its ±15 kV ESD protection improves robustness at connector locations where cables can be attached or disconnected, while the reduced slew rate helps reduce edge-related EMI compared with unrestricted-speed line drivers. The receiver incorporates communication-rate and slew-rate limiting to control bus behavior. These functions are especially useful in multipoint networks because they reduce the amount of high-frequency energy placed onto the cable. The device can participate in buses containing up to 32 transceivers, according to the manufacturer datasheet. Because its driver is intended for half-duplex operation, the design must control the driver-enable and receiver-enable inputs so that the bus is not driven during reception. Typical applications include industrial RS-485 links between controllers and sensors, factory-floor equipment, remote I/O modules, building-automation nodes, and instrumentation connected over long shielded or unshielded twisted-pair cables. In these systems, the low 250 kbps rate provides useful tolerance for wiring, propagation delay, reflections, and electromagnetic coupling. The ±12 V bus common-mode capability also helps the receiver tolerate voltage differences between grounded systems connected through the communication cable. PCB design should provide a continuous return path between the transceiver ground and the system ground, keep the differential pair route short where possible, and place termination and protection components near the bus connector. A common-mode choke can reduce conducted emissions when required, but it should be selected for the actual data rate and cable impedance. The supply bypass capacitor should be placed close to the VCC and GND pins to minimize high-frequency supply impedance. This page combines the manufacturer’s electrical limits, interface guidance, verified lifecycle information, package details, drop-in alternatives, and application-oriented design notes. It is intended to help engineers assess protocol compatibility, bus topology, protection strategy, and PCB implementation before integrating the ADM483EAR into an RS-485 or RS-422 design.
ADM483EARZ-REEL - 5V ±15kV ESD RS-485 Transceiver | Analog Devices
The Analog Devices ADM483EARZ-REEL is a 5 V, slew-rate-limited, half-duplex RS-485/RS-422 transceiver with ±15 kV ESD protection on the bus pins, supplied in an 8-pin SOIC_N (SO-8) package. It delivers 250 kbps data rate, supports up to 32 nodes on a single bus, and draws only 36 µA supply current, making it a low-power solution for industrial multipoint networks. A transceiver in the RS-485/RS-422 category is a differential line driver/receiver IC that converts a single-ended TTL/CMOS logic signal into a balanced differential signal (and vice versa) for transmission over twisted-pair media. RS-485 transceivers sit at the physical layer of multipoint fieldbus architectures and are widely used because they tolerate large common-mode voltages (-7 V to +12 V) and support long cable runs, with the TIA/EIA-485-A standard allowing up to 32 unit loads on a single bus. Key features include ±15 kV HBM ESD protection per IEC 61000-4-2 air-discharge testing on the bus pins, reduced slew rate to minimize EMI, a single 5 V ±10% supply, open-circuit fail-safe receiver design, thermal shutdown, short-circuit protection on the driver outputs, and a half-duplex (1/1) topology where driver and receiver share the same differential pair. The combination of low quiescent current and integrated ESD protection eliminates external TVS arrays in most designs. The device uses a BiCMOS process that integrates the differential driver, differential receiver, charge pump for fail-safe biasing, and ESD clamp structures on a single die. The reduced-slew-rate driver edges contain common-mode harmonics above 2 MHz, simplifying FCC Class B and EN 55022 EMI compliance on cables up to several hundred meters. Typical applications include industrial fieldbus nodes (Modbus, Profibus DP, BACnet), HVAC and building automation networks, motor and motion control links, smart-grid metering, point-of-sale terminals, and any 5 V MCU/UART-to-RS-485 interface requiring robust ESD protection. Designers should note that the ADM483E shares its bus pinout with industry-standard 8-pin half-duplex RS-485 pinouts such as the MAX485, LTC485, and SP485E, enabling direct footprint compatibility when migrating between families for ESD, speed, or supply current optimization.
ADM483JR - 250kbps Low-Power RS-485/RS-422 IC | Analog Devices
The Analog Devices ADM483JR is a 5 V, low-power, slew-rate-limited half-duplex RS-485/RS-422 differential line transceiver rated for data rates up to 250 kbps and housed in an 8-lead SOIC package. Its principal specifications are 120 µA typical operating supply current, 100 nA shutdown supply current, and a -7 V to +12 V bus common-mode range. According to the manufacturer product page and datasheet information, the ADM483 family is designed for low-power multipoint bus communication. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over longer cables and noisy environments. The ADM483 combines a differential line driver, differential receiver, and driver-enable control in one package. It sits within the hierarchy of interface IC, communications transceiver, differential line driver and receiver, and semiconductor. Its differential signaling improves noise immunity while supporting half-duplex operation on multipoint buses. The device supports EIA RS-485 and RS-422 operation, data rates to 250 kbps, and as many as 32 transceivers on one bus. Slew-rate limiting reduces electromagnetic interference, while high-impedance outputs when disabled or powered off help prevent bus contention. Thermal shutdown and short-circuit protection improve robustness, and the specified operating-temperature range is -40°C to +85°C. The ADM483 architecture supports low-power communication links where a lower data rate is acceptable and reduced switching activity is valuable. Its 120 µA supply current is suitable for low-power instrumentation and control links, while the 100 nA shutdown current supports power-sensitive systems. The 8-lead SOIC format supports conventional surface-mount assembly and easy transition from through-hole prototype boards to compact production designs. Typical uses include industrial control networks, building-automation equipment, instrumentation, low-speed data acquisition, and RS-485/RS-422 links between distributed modules. The device is particularly appropriate where low EMI, low standby consumption, and a moderate 250 kbps data rate are more important than maximum throughput. It is not intended as a substitute for a high-speed RS-485 transceiver when the application requires data rates above its stated limit. Designers should verify termination, biasing, protection, and grounding in the completed bus. Place the transceiver near the connector, provide a continuous ground reference, and use appropriate surge protection when cables leave the board. The 8-pin SOIC footprint allows straightforward layout, but input and output filtering should be evaluated alongside cable length and external transients. This page combines the verified ADM483 family specifications, sourcing links, practical design guidance, and same-package alternatives to help engineers evaluate a 250 kbps low-power RS-485/RS-422 transceiver.
ADM483JRZ - 250 kbps RS-485/RS-422 Transceiver | Analog Devices
The Analog Devices ADM483JRZ is a 5 V, low-power RS-485/RS-422 differential line transceiver supporting data rates up to 250 kbps in an 8-SOIC package. It combines one driver and one receiver for half-duplex multipoint communications, operates from a 4.75 V to 5.25 V supply, and uses slew-rate-limited edges to reduce electromagnetic interference. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and receives differential signals back into logic-level outputs. The RS-485 standard supports multipoint, half-duplex buses, while RS-422 provides balanced point-to-point or multidrop signaling. These differential interface ICs belong to the broader transceiver and interface IC hierarchy used to connect controllers, sensors, meters, industrial equipment, and communications systems over cables longer than ordinary logic interconnects. Key features include a maximum data rate of 250 kbps, low shutdown supply current of 100 nA, and low operating supply current of 120 µA. The device provides a -7 V to +12 V bus common-mode range and can support up to 32 transceivers on one bus. Driver outputs become high impedance when disabled or powered off, while thermal shutdown and short-circuit protection improve robustness in demanding wired networks. The ADM483 is designed for balanced data transmission over multipoint bus lines and complies with EIA RS-485 and RS-422 interfaces. Its slew-rate-limited output reduces EMI by slowing edge transitions, an important consideration in industrial environments containing clocks, motors, switching supplies, and long cable runs. The receiver provides differential signaling, allowing common-mode voltage differences on the bus to be rejected rather than appearing as noise at the logic interface. Typical applications include industrial control networks, building automation, instrumentation, security equipment, industrial modems, and low-speed data acquisition systems. The 250 kbps rate is appropriate for supervisory communications and control traffic rather than high-bandwidth Ethernet or video transport. Half-duplex operation also requires the system controller to arbitrate bus direction so that only one transmitter drives the pair at a time. For PCB implementation, place the device near the connector and route the differential bus as a controlled-impedance pair. Keep the ground reference close to the signal path and provide low-ESR bypass capacitance at the supply pins. Confirm termination, biasing, protection, and cable-length requirements for the selected RS-485 network because the transceiver alone does not determine the completed bus topology. This page consolidates the ADM483JRZ electrical characteristics, verified package information, drop-in cross-references, interface selection guidance, and practical PCB considerations into a procurement-oriented engineering reference.
ADM4850AR - 115 kbps RS-485/RS-422 Transceiver | Analog Devices
The Analog Devices ADM4850AR is a 5 V, slew-rate-limited differential line transceiver supporting RS-485 and RS-422 communication at data rates up to 115 kbps. The device is available in an 8-lead SOIC package and supports half-duplex and full-duplex line configurations. Its controlled output slew rate reduces electromagnetic interference, while the integrated receiver includes a true fail-safe function for improved bus behavior when the driver is disabled. A differential line transceiver converts between logic-level digital signals and balanced RS-485 or RS-422 signals. RS-485 is commonly used for multipoint industrial buses because differential signaling improves noise immunity and allows multiple nodes to share a two-wire bus when the system includes proper termination and biasing. RS-422 provides a balanced differential interface commonly used for point-to-point and legacy industrial communication links. The ADM4850AR belongs to the interface IC hierarchy and is positioned where a host UART or other controller must communicate over a physical bus. The principal feature of the ADM4850AR is its reduced slew rate. Slower signal-edge transitions lower the high-frequency content radiated by the driver and can reduce EMI problems in cables, connectors, and surrounding circuitry. The maximum data rate is 115 kbps, making the device appropriate for low- and moderate-speed factory automation, building-control, instrumentation, and embedded equipment links rather than high-speed backplane or storage networking. The ADM4850AR family includes multiple data-rate options, but the ADM4850 is the 115 kbps member. Half-duplex operation shares the driver and receiver path on the same bus pair, whereas full-duplex operation uses separate transmit and receive channels where the circuit topology permits it. Direction control and bus termination must be implemented correctly in the surrounding circuit, especially when the transceiver is used on a multipoint network with multiple drivers. Typical applications include industrial RS-485 links between controllers and sensors, building-automation equipment, remote instrumentation, and embedded data-acquisition systems. The limited data rate and slew rate are useful when long cables, modest connector spacing, and mixed industrial equipment make high-edge-rate drivers less attractive. Firmware should also avoid relying on the transceiver as a termination element because line termination belongs in the external network. For PCB design, place the transceiver close to the connector and bus interface, provide a solid ground reference, and keep differential traces routed as a closely coupled pair. The external network should follow the applicable RS-485 or RS-422 termination and biasing strategy. Confirm the complete pin assignment and operating limits in the manufacturer datasheet before finalizing a layout, especially when changing between half- and full-duplex configurations. This page combines the ADM4850AR interface description, verified product links, practical bus-layout guidance, and carefully scoped replacement criteria. It emphasizes the electrical roles that determine whether an RS-485 transceiver can be substituted without changing the PCB or degrading signal integrity.