بەرهەمەکان (5,100+)

PCA9703PW/Q900 - 16-bit SPI GPI, 18V Tolerant | NXP
PCA9703PW/Q900

PCA9703PW/Q900 - 16-bit SPI GPI, 18V Tolerant | NXP

The NXP Semiconductors PCA9703PW/Q900,118 is an 18 V tolerant, 16-bit SPI General Purpose Input (GPI) shift register with maskable interrupt output, housed in a 24-pin TSSOP (PW) package rated -40 C to +125 C. It operates as an SPI slave at up to 5 MHz and monitors 16 switch or logic inputs with 18 V input tolerance, making it a low-power solution for high-voltage switch status monitoring in automotive and industrial systems. A GPI (General Purpose Input) shift register is a type of input-only I/O expander within the broader hierarchy of interface ICs -> I/O expanders -> parallel-in serial-out shift registers. Unlike I2C GPIO expanders, SPI GPI shift registers stream input states to a microcontroller as a serial bit field, which minimizes pin count on the host MCU and gives deterministic, fast read-back of many switch contacts. Key features include 16 input-only channels tolerant to 18 V regardless of the device supply, a maskable INT output that flags any change of input state, a 3 V input switching threshold for robust noise immunity, and SPI compatibility up to 5 MHz. The Q900 suffix and /Q900,118 ordering code identify the automotive AEC-Q100 compliant variant with extended -40 C to +125 C operation; NXP states that PCA9703PW/Q900 is AEC-Q100 compliant and PPAP documentation is available via i2c.support@nxp.com. Technically, the PCA9703 samples its 16 GPI inputs into an internal shift register and shifts data out on MISO under host control of CS and SPI clock. Any input change (open, closed, or 12 V/24 V level via divider) triggers the interrupt output, which can be masked to prevent nuisance CPU wake-ups. The low-power CMOS process keeps static consumption minimal, which is critical for always-on battery-backed switch monitoring. Typical applications include automotive switch monitoring (door, window, seat, and steering-column switches), industrial control panels and limit-switch monitoring, and 12 V/24 V system status sensing where contacts ride on battery-level rails the chip inputs directly tolerate. A key design consideration is input threshold scaling: although inputs tolerate 18 V, the 3 V threshold means designers must confirm logic levels and switch pull-up arrangements so that a valid LOW is below threshold and a valid HIGH is safely above it across temperature. This page synthesizes distributor pricing, lifecycle status, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
PCA9703PW/Q900,118 - 16-Bit SPI GPI 18V Tolerant | NXP
PCA9703PW/Q900,118

PCA9703PW/Q900,118 - 16-Bit SPI GPI 18V Tolerant | NXP

The NXP Semiconductors PCA9703PW/Q900,118 is an 18 V tolerant SPI 16-bit General Purpose Input (GPI) shift register with maskable interrupt output, supplied in a 24-pin TSSOP package rated for -40 C to +125 C automotive operation with a 4.5 V to 5.5 V supply and a 5 MHz SPI clock. A general purpose input shift register is a specialized interface IC that converts parallel logic levels from switches or sensors into a serial data stream. In the system hierarchy it sits between raw switch inputs and a microcontroller: instead of dedicating 16 MCU pins to switch monitoring, a single SPI port reads all 16 inputs as a serial word, reducing pin count, wiring harness complexity, and cost in distributed control systems. Key features include 18 V tolerance on all GPI pins, allowing direct connection to automotive battery-nominal rails without level shifting; a maskable interrupt output (INT) with an INT_EN pin that disables the inputs and interrupt to minimize battery drain in cyclically powered systems; and an SDIN pin with pull-down that supports daisy-chaining multiple devices on a single SPI bus for 32, 48, or more inputs. Architecturally, the PCA9703 uses a shift register with a dedicated output enable controlled by CS. The 3 V logic thresholds on the serial interface ensure compatibility with both 3.3 V and 5 V controllers. Switch status is captured in the parallel input register and shifted out MSB-first on SCLK edges, with the interrupt flag readable on the first serial byte so the MCU can branch quickly on any input change. Typical applications include automotive switch monitoring for door, seat, and steering-column controls, body control modules and keypads, and industrial panels requiring isolated or battery-tolerant digital inputs. The 18 V tolerance is the decisive parameter wherever switches are wired to unregulated supply rails. A key design consideration: the GPI inputs require external pull-up or pull-down resistors to the switched rail; the INT_EN pin should be driven low during system sleep to eliminate quiescent current drawn through those resistors. This page synthesizes distributor pricing, drop-in alternative analysis, design notes, and application guidance not found in the manufacturer datasheet, making it a one-stop engineering reference for the PCA9703PW/Q900,118.

RFQ پەیوەندی
PCA9704PW/Q900 - 8-bit SPI GPI 18V Tolerant | NXP
PCA9704PW/Q900

PCA9704PW/Q900 - 8-bit SPI GPI 18V Tolerant | NXP

The NXP Semiconductors PCA9704PW/Q900 is an 8-bit, 18 V tolerant SPI General Purpose Input (GPI) shift register with maskable interrupt, AEC-Q100 qualified for automotive applications, housed in a 16-pin TSSOP (PW) package. It monitors the status of switch inputs and reads them out over a standard SPI interface running at up to 5 MHz. A general-purpose input expander is an interface IC that offloads switch or status-signal monitoring from a microcontroller. In the signal-chain hierarchy, the PCA9704 sits between discrete switch contacts and an MCU's SPI peripheral: GPIO expander -> interface IC -> mixed-signal logic device. Input expanders are used when an MCU lacks sufficient input pins or when switch signals sit at voltages higher than the MCU supply, as is common in automotive 12 V and 24 V electrical systems. Key features include eight input channels each tolerant to 18 V, allowing direct connection to battery-referenced switch contacts without external level shifting or clamping networks. The SPI interface supports read-out at up to 5 MHz, and a maskable interrupt output (INT) alerts the host controller only when inputs change, enabling low-power polled or event-driven system architectures. Technically, the PCA9704 is implemented as a parallel-in serial-out shift register with input latching. When the host asserts the chip-select, the current input state is latched and shifted out on the SPI data line; devices can be cascaded to expand beyond eight inputs on a single SPI bus. The /Q900 suffix denotes NXP's automotive product-line extension with AEC-Q100 compliance and PPAP support, distinguishing it from the commercial-grade PCA9704PW. Typical applications include automotive switch monitoring (door, seat, and key contacts), industrial control-panel status readback, and system diagnostics where battery-level fault or presence signals must be safely captured by a low-voltage controller. Design consideration: although the 18 V tolerance removes the need for input dividers, verify worst-case battery load-dump transients in automotive systems and confirm that the interrupt mask register is initialized before enabling INT to avoid spurious wake-ups at power-up. This page synthesizes distributor data, automotive-grade alternative options, and practical SPI integration notes not found in the manufacturer datasheet, with pricing verified as of 2026-10-19.

RFQ پەیوەندی
PCAL6408AHK - 8-Bit I2C I/O Expander, XQFN-16 | NXP
PCAL6408AHK

PCAL6408AHK - 8-Bit I2C I/O Expander, XQFN-16 | NXP

The NXP Semiconductors PCAL6408AHK is a low-voltage translating, 8-bit general-purpose I/O expander with interrupt output, reset, and Agile I/O configuration registers, interfacing to a host microcontroller via I2C-bus/SMBus at up to 400 kHz in a 16-pin XQFN (1.8 x 2.6 mm) package. An I/O expander is a peripheral IC that adds extra general-purpose input/output pins to a microcontroller or embedded processor over a serial bus such as I2C or SMBus. In the system hierarchy, it sits within the interface IC family, under mixed-signal peripheral devices, and complements microcontrollers whose native GPIO count is exhausted. Expanders offload GPIO expansion while consuming only two bus wires (SDA, SCL), conserving processor pins and board routing. Key features include a wide supply range of 1.65 V to 5.5 V, dual power rails for true voltage level translation between logic domains, programmable output drive strength, and latchable inputs. The interrupt output and active-low reset provide robust event-driven and fault-recovery behavior in multi-slave I2C systems. The Agile I/O feature set - configurable output drive, input latch, and pull-up/pull-down enable - allows system designers to tune signal integrity and power per pin, which is significant in mixed-voltage designs where a 1.8 V MCU must safely drive 3.3 V or 5 V peripherals. Open-drain and push-pull operating modes over I2C/SMBus at 400 kHz provide flexible bus integration. Typical applications include GPIO expansion in portable and battery-powered devices, level translation between low-voltage processors and legacy 5 V peripherals, sensor and keypad scanning, LED control, and backplane status monitoring in industrial systems. Design consideration: because the XQFN-16 package measures only 1.8 x 2.6 mm, the exposed pad must be soldered to a grounded PCB land pattern for reliable thermal and mechanical performance; verify land-pattern tolerances before assembly. This page synthesizes distributor pricing context, drop-in alternatives, practical design notes, and AEO-optimized FAQs not found in the NXP datasheet.

RFQ پەیوەندی
PCF85176T/1 - 40x4 LCD Segment Driver I2C TSSOP-56 | NXP
PCF85176T/1

PCF85176T/1 - 40x4 LCD Segment Driver I2C TSSOP-56 | NXP

The NXP Semiconductors PCF85176T/1 is a universal LCD segment driver with 40 segments and 4 backplanes, packaged in a 56-pin TSSOP (TSSOP-56). It interfaces to almost any Liquid Crystal Display (LCD) with low multiplex rates via an I2C-bus and generates the drive signals required for static or multiplexed LCDs up to 4x40. The device supports a frame frequency of 82 Hz and is widely used where cascadable LCD expansion is needed. A segment driver (LCD driver) is a peripheral device that translates digital commands from a microcontroller into the multi-level AC waveforms required to drive a passive-matrix liquid crystal display. LCD segment drivers sit in the display driver hierarchy above simple character LCD modules, providing designers with a low-pin-count way to control custom glass through bias generation, backplane sequencing, and segment latching. The PCF85176T/1 combines on-chip bias generation with a serial I2C interface so an MCU only needs two I/O lines to address 160 individual pixel segments. Key features include 40 segment outputs plus 4 backplane outputs (160 pixel capability), integrated charge-pump-based LCD bias voltage generator, selectable bias modes for static, 2-way, 3-way, and 4-way multiplexing, an I2C-bus interface with hardware-selectable slave addresses for cascading, on-chip oscillator requiring no external components, and a wide logic supply range compatible with 3.3 V and 5 V microcontrollers. The CMOS process and TSSOP-56 footprint keep the part economical for mid-volume industrial and consumer LCD designs. The architecture consists of an I2C slave controller, a display RAM of 80 bits (40 segments x 2 pages), a programmable frame frequency generator, and a segment/backplane driver block tolerant of liquid crystal threshold voltages typically between 3 V and 9 V. The integrated VLCD generator eliminates the need for an external DC-DC converter in many designs, reducing BOM cost and PCB area. Typical applications include point-of-sale (POS) terminals, industrial control panels with character or numeric LCDs, white-goods user interfaces such as washing machines and microwave ovens, automotive instrument cluster sub-displays, medical instrument readouts, and metering equipment (water/gas/electricity meters). Cascading multiple PCF85176T/1 devices enables larger glass panels, supporting display sizes up to 320 segments in a chain. When designing with this part, use the on-chip bias generator to produce VLCD rather than an external rail, and reserve one I2C address bit per cascaded chip. Designers should also enable the internal oscillator unless precise frame frequency synchronization is required by the application.

RFQ پەیوەندی
PCF8562TT/2 - 4x32 I2C LCD Segment Driver | NXP | TSSOP-48
PCF8562TT/2

PCF8562TT/2 - 4x32 I2C LCD Segment Driver | NXP | TSSOP-48

The NXP PCF8562TT/2 is a universal LCD segment driver with 4 backplanes and 32 segments, controlled via the two-line bidirectional I2C-bus, housed in a 48-pin TSSOP (SOT362-1) package. It supports supply voltages of 2.5V, 3.3V, and 5V, a typical frame frequency of 64 Hz, and operating temperatures from -40C to +85C. The CMOS device drives static, 2-way, 3-way, or 4-way multiplexed LCDs with selectable static, 1/2, or 1/3 bias configuration. An LCD segment driver is an integrated circuit that generates the AC voltage waveforms required to drive individual segments of a liquid-crystal display. It sits hierarchically between the microcontroller (which decides what to display) and the LCD glass (which physically renders pixels). The PCF8562 belongs to the LCD driver family, which is a subcategory of display driver ICs, itself part of the broader power management and interface semiconductor landscape. Because it uses I2C and runs from a single low-voltage rail, it is a common choice in battery-powered and embedded designs. Key features include selectable backplane drive configuration (static, 2, 3, or 4 backplane multiplexing), selectable display bias configuration (static, 1/2, or 1/3), and a 64 Hz typical frame frequency that minimizes flicker for direct-driven LCDs. The device integrates charge-pump-based bias generation and can drive up to 128 segments in 4-mux mode (4 backplanes x 32 segments). Automotive-grade variants such as PCF8562TT/S400/2 carry AEC-Q100 compliance, making the family suitable for dashboard clusters and instrument panels. From a technical depth perspective, the PCF8562 uses CMOS technology to minimize quiescent current, supports cascadable I2C clock stretching, and includes an internal oscillator with external resistor adjustment. The architecture separates the I2C slave logic (pins SDA, SCL, SA0) from the high-voltage LCD driver outputs (BP0-BP3, S0-S31), allowing the digital core to operate at logic levels while the segment outputs swing to VLCD. Designers typically pair the PCF8562 with a host MCU such as the LPC family or general-purpose microcontrollers using only two GPIO pins for the entire interface. Typical applications include metering displays (electricity, water, gas meters), white goods front panels, point-of-sale terminals, automotive instrument clusters (with the /S400/2 variant), medical device readouts, and any low-multiplex-rate character or graphic LCD up to 32 segments per chip. Two or more PCF8562 devices can share a single I2C bus by using different SA0 slave-address straps. The 48-pin TSSOP footprint makes it compatible with hand-solderable prototypes and high-density production boards alike. When designing with the PCF8562, ensure VLCD is properly bypassed with a 100 nF ceramic capacitor and that BP0-BP3 traces are kept short to reduce display ghosting. Designers should also verify the slave address selection via the SA0 pin to avoid bus conflicts when cascading multiple drivers. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
PCF8574ADW - 8-Bit 5.5V I2C I/O Expander | Texas Instruments
PCF8574ADW

PCF8574ADW - 8-Bit 5.5V I2C I/O Expander | Texas Instruments

Texas Instruments PCF8574ADW is an 8-bit I2C/SMBus input/output expander operating from 2.5 V to 5.5 V, supporting I2C communication at 100 kHz in a 16-pin SOIC (DW) package. It adds eight quasi-bidirectional I/O ports and an interrupt output to a host controller, reducing the number of GPIO pins required by embedded systems. An I/O expander is an interface IC that extends the input/output capacity of a host such as a microcontroller or application processor. The PCF8574 belongs to the I2C I/O expander hierarchy and uses the two-wire bus for command and status transfers. Eight ports can be individually configured as inputs or outputs, while address pins allow multiple expanders to coexist on the same bus. Key features include eight I/O lines, a 2.5 V to 5.5 V operating range, 100 kHz I2C operation, and an open-drain interrupt output. The interrupt output allows the connected processor to respond when a change occurs on an input port rather than continuously polling all eight lines. The SOIC-16 package supports conventional surface-mount assembly and is available in a -40 °C to +85 °C temperature grade. The PCF8574A architecture uses quasi-bidirectional ports capable of both input and output operation. Each port can be driven low or released high, while an external pull-up resistor is normally required to establish the high state. The three address inputs select one of eight device addresses, allowing several PCF8574 devices to share common SCL and SDA nets. Power-on behavior depends on the external pull-up network and must be considered when defining system defaults. Typical uses include reading control buttons and switches, driving discrete LEDs, monitoring digital status signals, and expanding the GPIO capacity of industrial controllers, test equipment, access-control panels, and compact embedded products. The interrupt line is especially useful in systems where periodic I2C polling would waste processor time or create unnecessary bus activity. Design the interface around the device's open-drain bus architecture. Place pull-up resistors on SDA and SCL close to the bus master, confirm address-strapping levels before enabling the device, and account for the port high-current limitations when driving capacitive or LED loads. The manufacturer datasheet is the controlling reference for pinout, timing, output-current limits, and electrical characteristics.

RFQ پەیوەندی
PCF8574ADWR - 8-Bit 5.5V I2C I/O Expander | Texas Instruments (Tape & Reel)
PCF8574ADWR

PCF8574ADWR - 8-Bit 5.5V I2C I/O Expander | Texas Instruments (Tape & Reel)

Texas Instruments PCF8574ADWR is an 8-bit I2C/SMBus input/output expander operating from 2.5 V to 5.5 V, supporting I2C communication at 100 kHz in a 16-pin SOIC (DW) package. It adds eight quasi-bidirectional I/O ports and an interrupt output to a host controller, reducing the number of GPIO pins required by embedded systems. An I/O expander is an interface IC that extends the input/output capacity of a host such as a microcontroller or application processor. The PCF8574 belongs to the I2C I/O expander hierarchy and uses the two-wire bus for command and status transfers. Eight ports can be individually configured as inputs or outputs, while address pins allow multiple expanders to coexist on the same bus. Key features include eight I/O lines, a 2.5 V to 5.5 V operating range, 100 kHz I2C operation, and an open-drain interrupt output. The interrupt output allows the connected processor to respond when a change occurs on an input port rather than continuously polling all eight lines. The SOIC-16 package supports conventional surface-mount assembly and is available in a -40 °C to +85 °C temperature grade. The PCF8574A architecture uses quasi-bidirectional ports capable of both input and output operation. Each port can be driven low or released high, while an external pull-up resistor is normally required to establish the high state. The three address inputs select one of eight device addresses, allowing several PCF8574 devices to share common SCL and SDA nets. Power-on behavior depends on the external pull-up network and must be considered when defining system defaults. Typical uses include reading control buttons and switches, driving discrete LEDs, monitoring digital status signals, and expanding the GPIO capacity of industrial controllers, test equipment, access-control panels, and compact embedded products. The interrupt line is especially useful in systems where periodic I2C polling would waste processor time or create unnecessary bus activity. Design the interface around the device's open-drain bus architecture. Place pull-up resistors on SDA and SCL close to the bus master, confirm address-strapping levels before enabling the device, and account for the port high-current limitations when driving capacitive or LED loads. The manufacturer datasheet is the controlling reference for pinout, timing, output-current limits, and electrical characteristics.

RFQ پەیوەندی
PCF8574AN - 8-Bit I/O Expander | Texas Instruments | DIP
PCF8574AN

PCF8574AN - 8-Bit I/O Expander | Texas Instruments | DIP

The Texas Instruments PCF8574AN is an 8-bit remote I/O expander intended for digital input and output expansion in embedded systems. The device communicates with a host controller through a two-wire serial interface and provides eight separately addressable I/O lines. It is supplied in a 16-pin dual in-line package, with the AN order suffix identifying the packaged variant. This addressable I/O architecture places the PCF8574AN in the interface IC hierarchy: serial interface controller, I/O expander, embedded-system interface, and semiconductor. A remote I/O expander reduces the number of general-purpose I/O pins required on a microcontroller, programmable logic controller, or other embedded controller. Eight digital lines can be distributed across a remote circuit board, allowing buttons, indicators, logic inputs, or other digital signals to connect to a shared two-wire bus. The PCF8574AN therefore reduces package size and routing complexity when a design requires more digital interface lines than the host controller provides directly. The verified dataset supplied for this product contains no manufacturer-document specifications or distributor records. Consequently, operating voltage, address range, output-drive capability, clock frequency, logic thresholds, quiescent current, and environmental ratings are not asserted on this page. These parameters must be confirmed from the applicable Texas Instruments manufacturer datasheet before the IC is used in a new schematic, PCB layout, firmware configuration, or safety- and reliability-critical design. The PCF8574AN is typically associated with 5 V and 3.3 V embedded systems, but the actual supported supply range and interface levels are deliberately left unspecified here because no verified manufacturer data was provided. Logic-level compatibility must be evaluated using the authoritative input thresholds, output leakage, and output-driver specifications rather than nominal rail voltage alone. Typical design candidates include general-purpose microcontroller I/O expansion, programmable controller input modules, front-panel button and indicator handling, and simple industrial control boards. An I2C or other two-wire host bus may be shared by multiple expanders only after address allocation, electrical loading, pull-up requirements, and bus-speed limits have been verified. The primary layout concern is the two-wire bus. Place pull-up resistors and decoupling capacitors close to the appropriate bus endpoints, keep the clock and data traces short, and confirm that every connected device can tolerate the selected voltage and clock rate. Firmware must also establish the device address and configure each line as input or output before external hardware is energized. This page combines an authenticity-first specification record with procurement, replacement, selection, and design-intent guidance. Because the retrieved distributor and cross-reference searches returned no records, market pricing, lifecycle availability, exact pin naming, and additional drop-in alternatives remain explicitly unverified rather than being inferred from similar devices.

RFQ پەیوەندی
PCF8574ANG4 - 8-Bit 100kHz I2C I/O Expander | Texas Instruments
PCF8574ANG4

PCF8574ANG4 - 8-Bit 100kHz I2C I/O Expander | Texas Instruments

Texas Instruments PCF8574ANG4 is an 8-bit I2C I/O expander operating at a 100 kHz bus frequency and packaged in a 16-pin PDIP enclosure measuring 0.300 inches with 7.62 mm lead spacing. It adds eight general-purpose input/output lines to a host controller while using an I2C connection for register communication. An I/O expander is a semiconductor interface device that extends the number of digital lines available to a microcontroller or other embedded controller. It belongs to the I/O expander category within interface ICs, where the device translates serial bus commands into parallel input or output states. This approach reduces direct GPIO requirements and is especially useful when a host controller has limited connector pins. The PCF8574ANG4 provides eight I/O positions and uses a two-wire I2C interface with a maximum stated bus frequency of 100 kHz. Its 16-pin PDIP package supports conventional through-hole PCB assembly and is identifiable by its 0.300-inch body width and 7.62 mm lead pitch. These mechanical dimensions help engineers match the component to an existing footprint and connector arrangement. Operationally, the expander is intended to read or control external digital lines while the host processor manages address selection, register access, and application behavior. I2C communication allows the host to update output states or sample input states over the serial bus, reducing the number of wires needed between the controller and remote digital hardware. The 100 kHz operating limit should be considered when designing the bus topology. Typical uses include keypad and control-panel interfaces, relay and indicator outputs, digital sensor gathering, industrial automation modules, embedded control boards, and compact consumer accessories. The eight available lines make the device especially practical where modest GPIO expansion is required rather than a large bank of isolated inputs or high-speed outputs. For PCB implementation, confirm the 16-pin PDIP footprint and 7.62 mm pitch against the mechanical drawing before layout. I2C pull-up requirements, bus capacitance, address configuration, and the maximum supported bus frequency must be evaluated in the complete circuit. This page combines package, interface, application, replacement, and design information for faster component selection.

RFQ پەیوەندی
PCF8574APW - 8-Bit I2C I/O Expander | Texas Instruments
PCF8574APW

PCF8574APW - 8-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCF8574APW is an 8-bit I2C/SMBus remote I/O expander with interrupt support, a 2.5 V to 5.5 V operating-voltage range, and a 20-pin TSSOP package. It adds eight quasi-bidirectional port lines to a host microcontroller through a two-wire serial interface, making it useful when a controller has insufficient general-purpose I/O pins. An I/O expander is an interface IC that translates serial bus commands into parallel digital input and output access. The PCF8574A family belongs to the I/O expander category within interface ICs, interface semiconductors, and electronic components. Its remote port can connect to buttons, indicators, logic inputs, control signals, and other digital peripherals while the host processor retains access through the I2C bus. The device provides eight quasi-bidirectional I/O pins, an interrupt output, three hardware address inputs, and operation from 2.5 V to 5.5 V. According to the Texas Instruments PCF8574A product page, the device supports both I2C and SMBus communication. The manufacturer datasheet also identifies a maximum standby-current consumption of 10 microamperes, supporting designs where standby power is an important consideration. The A designation identifies the address-selectable version of the PCF8574 family. Each device offers three address inputs, allowing multiple expanders to share one serial bus when suitable bus addresses are assigned. The interrupt output provides a hardware indication that input-port state has changed, reducing the need for the host controller to poll every port continuously. Typical uses include expanding microcontroller GPIO for human-interface controls, monitoring switches and keypads, driving LEDs or logic-enable signals, controlling discrete system inputs, and supporting industrial interface modules. It can also reduce the number of I/O pins required on a microcontroller, processor, or programmable logic controller. A hardware design should treat the quasi-bidirectional port outputs carefully because each line may be weakly driven high and can be pulled low by an external device. Designers should review the port architecture, address pins, bus pull-up requirements, and interrupt behavior in the manufacturer datasheet before finalizing the circuit. This product page combines the manufacturer electrical characteristics, interface details, application guidance, pin assignment information, and verified substitute analysis. It also highlights the limits of direct replacement: identical pin count and package dimensions alone do not guarantee that two I/O expanders use identical addressing, interrupt, electrical, or qualification behavior.

RFQ پەیوەندی
PCF8574AT/3,518 - 8-bit I2C I/O Expander | NXP SOIC-16
PCF8574AT/3,518

PCF8574AT/3,518 - 8-bit I2C I/O Expander | NXP SOIC-16

The NXP PCF8574AT/3,518 is an 8-bit I/O expander with quasi-bidirectional I/O pins, an I2C-bus interface operating up to 100 kHz, and an open-drain interrupt output, housed in a 16-pin SO (SOIC-16, MS-013/SOT-162-1) plastic package. It operates from 2.5 V to 6 V supply, supports three hardware address pins (A0-A2), and provides a different fixed I2C address base than the PCF8574 (0x3F for the PCF8574A family vs 0x20 for the PCF8574A base, allowing up to eight of each on the same bus). The CMOS silicon-gate design draws low quiescent current (typ. 40 uA) and supports a maximum of 16 PCF8574/PCF8574A devices on one shared I2C-bus, expanding up to 128 I/Os. An I/O expander is a class of digital peripheral IC that extends the limited GPIO count of a host microcontroller through a serial bus, allowing additional inputs, outputs, keypads, LED indicators, and signal-conditioning lines without increasing pin count on the MCU. Within the hierarchy of interface ICs (also called bus expanders or GPIO extenders), the PCF8574AT belongs to the I2C-bus parallel-port family, positioned between simple shift-register expanders (which lack interrupt capability) and full SPI/I2C port-mapped devices. This category sits under digital logic and interface ICs in broader semiconductor taxonomy, supporting both consumer and industrial designs where MCU pin count is constrained. Key features include quasi-bidirectional I/O that can directly drive LEDs without external pull-ups (sinking capability of up to 25 mA per pin, max 100 mA total), an active-low interrupt output (INT) that signals the host when any input state changes, and 400 kHz Fast-mode I2C capability on the PCF8574A/PCF8574AT family variants. The device integrates a noise filter on the SCL/SDA lines and supports clock stretching as a slave device. The PCF8574AT uses a CMOS silicon-gate architecture with latched output registers and input latches on every I/O pin. The quasi-bidirectional design uses a weak pull-up (typically 100 uA current source) to drive outputs high; pulling low requires the pin to actively sink current. This architecture eliminates the need for external pull-up resistors on outputs while maintaining low standby current. Typical applications include driving LED arrays, LCD segment interfaces, keypad matrix scanning, fan-speed monitoring, relay control boards, and general-purpose I2C slave peripheral expansion in industrial control, consumer electronics, and embedded systems. Engineers commonly pair the PCF8574AT with low-power MCUs (such as the LPC1100 or PIC16F families) to add 8-bit digital I/O over only two signal wires. When designing with this part, note that the quasi-bidirectional I/O pins have an asymmetric drive capability - they source weakly (100 uA) but sink strongly (25 mA per pin). This makes them ideal for LED-driving (sink mode) but less suitable as push-pull signal drivers. Always respect the absolute maximum of 100 mA total current through the VDD/GND pins to avoid latch-up. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone, including cross-references for the very similar PCF8574T/3 (different I2C address range).

RFQ پەیوەندی
PCF8574DW - 8-Bit 100kHz I2C I/O Expander | Texas Instruments
PCF8574DW

PCF8574DW - 8-Bit 100kHz I2C I/O Expander | Texas Instruments

Texas Instruments PCF8574DW is an 8-bit I2C I/O expander with a 100 kHz bus, eight quasi-bidirectional ports, and an interrupt output, supplied in a 16-SOIC package. According to the manufacturer product page, it supports 2.5 V to 5.5 V operation, while the manufacturer datasheet search result describes 2.5 V to 6 V VCC operation. The device adds eight parallel digital lines to a host microcontroller without consuming eight dedicated GPIO pins. An I/O expander is an interface IC that translates serial I2C commands into parallel digital inputs or outputs. The PCF8574 belongs to the parallel-port expansion and I2C interface hierarchy. It uses two bus lines, SCL and SDA, to receive configuration and port-state data from a microcontroller, then presents P0 through P7 as individually controlled digital ports. Its interrupt output allows a host to react when an input condition changes without continuously polling the bus. The principal features include eight I/O ports, a maximum I2C clock frequency of 100 kHz, a 2.5 V to 6 V VCC operating range stated in the datasheet, and low standby-current consumption with a listed maximum standby current of 10 µA. The open-drain interrupt output is compatible with common microcontroller interrupt inputs. The 16-SOIC package is a surface-mount SOIC-16 footprint, and the DWR tape-and-reel ordering code must not be confused with the DW tube ordering code. The quasi-bidirectional port architecture makes the PCF8574 useful for simple control and status signals. A port can be written as an output or sampled as an input, but the electrical behavior and pull-up implementation require care when driving external loads. The interrupt pin provides an event-oriented alternative to periodic reads when one or more input lines change state. Firmware must also verify the device address and bus pull-up arrangement when multiple expanders share the same two-wire bus. Typical applications include keypad and control-panel scanning, relay or solenoid control, LED indication, sensor and switch input aggregation, industrial control modules, and general embedded systems where a microcontroller has too few GPIO pins. The expander is particularly useful when the required signals are simple logic levels and the bus is already present. It is less suitable when high-speed edge-sensitive inputs, high-current output drive, or strong isolation requirements are present. Designers should verify pull-up resistors on SDA and SCL, ensure that all connected devices use compatible voltage levels, and account for total bus capacitance. Port pins intended as inputs should not be forced into incompatible logic states, while output loads should remain within verified current and voltage limits. This page combines the supplied manufacturer and distributor data with practical design guidance, comparison parameters, and sourcing information.

RFQ پەیوەندی
PCF8574DWE4 - 8-Bit I2C I/O Expander | Texas Instruments
PCF8574DWE4

PCF8574DWE4 - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments PCF8574DWE4 is an 8-bit remote input/output expander for the two-wire bidirectional I2C bus, operating from 2.5 V to 6 V VCC with eight quasi-bidirectional I/O lines and a 100 kHz I2C interface. The device is supplied in a 16-pin SOIC package with a 1.27 mm terminal pitch. An I2C I/O expander is an interface IC that increases the number of general-purpose input and output pins available to a host microcontroller or processor. It belongs to the parallel I/O port hierarchy, extends the I2C interface family, and reduces the number of GPIO pins required on the controlling device. Each port pin can be selected as an input or output through the device register interface, while the open-drain INT output can notify the host of an input state change. The PCF8574DWE4 provides eight individually controlled I/O lines, operation across a 2.5 V to 6 V supply range, and I2C communication at up to 100 kHz. Its low standby-current consumption is 10 µA maximum. The three external address inputs permit multiple expanders to share an I2C bus when their hardware addresses are configured differently, while the package supports conventional surface-mount PCB assembly. The device uses quasi-bidirectional port architecture, allowing each P0 through P7 line to operate as an input or output under software control. Pull-up resistors are normally required for open-drain bus signals. Because the I2C pins also support 3-state operation, a port can be disconnected temporarily to support bus communication involving devices that detect a target address on the same bus. Typical applications include industrial control panels, sensor and relay interfaces, LED status indicators, keyboard scanners, programmable logic controllers, and compact embedded systems. The 8-bit port width is particularly useful when a controller must monitor discrete switches or command several actuators without allocating eight dedicated GPIO pins to every function. PCB design should preserve short I2C routing, provide pull-up resistors on SDA and SCL, and keep the address-strapping tracks accessible if multiple device addresses are required. Validate the controller voltage, peripheral voltage, and logic thresholds when the expander operates from a supply different from the I2C bus pull-up level. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks. This product page organizes the operating limits, interface details, package information, replacement candidates, and practical implementation considerations needed to evaluate the PCF8574DWE4 in an embedded I2C design.

RFQ پەیوەندی
PCF8574DWR - 8-Bit 100kHz I2C I/O Expander | Texas Instruments (Tape & Reel)
PCF8574DWR

PCF8574DWR - 8-Bit 100kHz I2C I/O Expander | Texas Instruments (Tape & Reel)

Texas Instruments PCF8574DWR is an 8-bit I2C I/O expander with a 100 kHz bus, eight quasi-bidirectional ports, and an interrupt output, supplied in a 16-SOIC package. According to the manufacturer product page, it supports 2.5 V to 5.5 V operation, while the manufacturer datasheet search result describes 2.5 V to 6 V VCC operation. The device adds eight parallel digital lines to a host microcontroller without consuming eight dedicated GPIO pins. An I/O expander is an interface IC that translates serial I2C commands into parallel digital inputs or outputs. The PCF8574 belongs to the parallel-port expansion and I2C interface hierarchy. It uses two bus lines, SCL and SDA, to receive configuration and port-state data from a microcontroller, then presents P0 through P7 as individually controlled digital ports. Its interrupt output allows a host to react when an input condition changes without continuously polling the bus. The principal features include eight I/O ports, a maximum I2C clock frequency of 100 kHz, a 2.5 V to 6 V VCC operating range stated in the datasheet, and low standby-current consumption with a listed maximum standby current of 10 µA. The open-drain interrupt output is compatible with common microcontroller interrupt inputs. The 16-SOIC package is a surface-mount SOIC-16 footprint, and the DWR tape-and-reel ordering code must not be confused with the DW tube ordering code. The quasi-bidirectional port architecture makes the PCF8574 useful for simple control and status signals. A port can be written as an output or sampled as an input, but the electrical behavior and pull-up implementation require care when driving external loads. The interrupt pin provides an event-oriented alternative to periodic reads when one or more input lines change state. Firmware must also verify the device address and bus pull-up arrangement when multiple expanders share the same two-wire bus. Typical applications include keypad and control-panel scanning, relay or solenoid control, LED indication, sensor and switch input aggregation, industrial control modules, and general embedded systems where a microcontroller has too few GPIO pins. The expander is particularly useful when the required signals are simple logic levels and the bus is already present. It is less suitable when high-speed edge-sensitive inputs, high-current output drive, or strong isolation requirements are present. Designers should verify pull-up resistors on SDA and SCL, ensure that all connected devices use compatible voltage levels, and account for total bus capacitance. Port pins intended as inputs should not be forced into incompatible logic states, while output loads should remain within verified current and voltage limits. This page combines the supplied manufacturer and distributor data with practical design guidance, comparison parameters, and sourcing information.

RFQ پەیوەندی
PCF8574N - 8-Bit 100kHz I2C I/O Expander | Texas Instruments
PCF8574N

PCF8574N - 8-Bit 100kHz I2C I/O Expander | Texas Instruments

The Texas Instruments PCF8574N is an 8-bit bidirectional I/O expander for the I2C bus, operating from 2.5V to 6V with a 100kHz interface and housed in a 16-pin PDIP package. It adds eight quasi-bidirectional remote I/O lines to a host microcontroller while providing open-drain interrupt signaling. The device is designed for general-purpose expansion across embedded control, communications, and embedded accessory designs. What is an I2C I/O expander? An I/O expander is an interface IC that translates serial bus commands into parallel digital signals. The PCF8574N belongs to the I/O-expander class, which sits within interface ICs and broader semiconductor systems. It helps a controller with too few GPIO pins operate additional buttons, indicators, relays, or other digital peripherals while preserving a shared SDA and SCL bus. Key features include eight I/O ports, 100kHz I2C operation, a 2.5V to 6V supply range, and an interrupt output. Its quasi-bidirectional ports can be configured as inputs or outputs, while power-on behavior and external pull-up requirements must be considered in the system design. The verified distributor listing identifies the PCF8574N as an 8-bit, 100kHz I/O expander in a PDIP package. The device uses the PCF8574 family architecture in which the host communicates over the two-wire I2C bus and reads or writes the remote port state. Because the ports are quasi-bidirectional rather than independently powered high-impedance inputs and outputs, firmware and external circuitry should avoid contention scenarios. The interrupt line provides a hardware indication that input data has changed, reducing unnecessary serial polling when the application supports it. Typical applications include microcontroller GPIO expansion, keypad and control panels, relay or indicator interfaces, industrial automation modules, communications equipment, and embedded systems using the site-listed STM32, ATMEGA, MSP430, or other microcontroller families. The same I2C bus can support multiple addressed peripherals, subject to the device address configuration and bus capacitance requirements. Designers should follow the manufacturer datasheet for pull-up resistor selection, address strapping, decoupling, input/output polarity, and interrupt handling. Confirm the available voltage range against the connected bus and peripherals, and verify absolute maximum ratings before using the device in systems with long cables or exposed connectors. The 16-pin PDIP package favors through-hole prototyping rather than compact surface-mount production. This page combines the verified manufacturer and distributor information for PCF8574N with package, selection, design, and application guidance. It is intended to help engineers identify whether the part fits a particular I2C expansion requirement before comparing alternatives or requesting supply.

RFQ پەیوەندی
PCF8574NG4 - 8-Bit I2C I/O Expander | Texas Instruments
PCF8574NG4

PCF8574NG4 - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments PCF8574NG4 is an 8-bit I/O expander for the two-line bidirectional I2C bus, operating from 2.5 V to 6 V VCC at a maximum bus frequency of 100 kHz. It is housed in a 16-pin PDIP package measuring 0.300 inches with 7.62 mm lead spacing. The device expands one I2C controller into eight quasi-bidirectional GPIO lines for sensors, relays, switches, logic controls, and other external interfaces. An I/O expander is an interface IC that extends the number of general-purpose inputs and outputs available to a microcontroller or other host processor. The I2C interface uses serial clock and serial data lines to transfer address and port information, while the parallel port provides individual connections to external hardware. This hierarchy places the PCF8574 within I2C interface controllers, interface ICs, and semiconductor-based system expansion components. The PCF8574 combines an 8-bit quasi-bidirectional port with an I2C interface. Quasi-bidirectional operation means each port can be used for input or output, with output drivers capable of sinking current while the input state can be detected. An interrupt output provides a way for the host to react when a changing input condition is detected, reducing the need for continuous I2C polling in suitable designs. The 2.5 V to 6 V VCC range allows the device to operate with both 3.3 V and 5 V system rails. Its 100 kHz I2C maximum supports conventional standard-mode bus operation and broad compatibility with embedded processors. The remote port also reduces the number of GPIO pins required from the host controller, which can simplify pin allocation in compact embedded systems. Typical uses include relay and solenoid control, keypad and switch sensing, LED or indicator interfaces, sensor input collection, and industrial control panels. The same electrical interface is useful when the remote equipment is physically separated from the host because the PCF8574 communicates through the bus while exposing local input and output connections at the port. Design with the port's quasi-bidirectional characteristics and the electrical limits in the manufacturer datasheet in mind. Pull-up requirements, address selection, bus capacitance, output-driver topology, and reset behavior must be checked against the specific system. Do not assume that every quasi-bidirectional port can source the same current that it can sink. This page combines the manufacturer electrical operating range, package details, pin-level guidance, and application-oriented analysis with a focused comparison of verified same-package alternatives. It also identifies design trade-offs that are not obvious from a distributor category listing, helping engineers determine whether the 16-pin PCF8574NG4 remains suitable for a new embedded interface design.

RFQ پەیوەندی
PCF8574P - 8-Bit 100kHz I2C I/O Expander | NXP
PCF8574P

PCF8574P - 8-Bit 100kHz I2C I/O Expander | NXP

The NXP Semiconductors PCF8574P is an 8-bit remote I/O expander for the two-wire bidirectional I2C-bus, with a 100 kHz bus interface, three hardware address inputs, eight quasi-bidirectional ports, and an interrupt output in a 16-pin DIP package. It operates from a 2.5 V to 6 V supply. An I/O expander is an interface IC that increases the number of general-purpose input and output pins available to a host microcontroller. The PCF8574P uses serial clock and serial data lines to transfer port data over I2C, while the eight parallel port pins connect directly to switches, LEDs, indicators, keypads, or other external circuitry. Its place in the component hierarchy is interface IC, then I/O expander, then peripheral expansion device. The PCF8574P provides 8-bit port control, 100 kHz I2C operation, three address-selection inputs, and an active-low open-drain interrupt output. The three address inputs allow multiple expanders to share the same SDA and SCL bus. The interrupt output lets a controller identify a change on an input port without continuously polling every expander. These features suit systems that need additional GPIO but have limited direct pins on the host controller. The device consists of an 8-bit quasi-bidirectional port and an I2C interface. Each quasi-bidirectional port can be configured as an input or output, although outputs have a limited drive capability compared with general-purpose push-pull microcontroller pins. Pull-up resistors are required for open-drain I2C lines, and the external bus design must account for capacitance, pull-up strength, voltage compatibility, and the number of connected devices. Typical applications include Arduino-compatible control boards, ESP32-based IoT controllers, LED and key-matrix interfaces, relay-control modules, industrial automation equipment, and embedded products requiring eight additional GPIO lines. The PCF8574P is especially useful when adding a modest number of pins is preferable to selecting a host microcontroller with a larger pin count or redesigning the main board. For reliable operation, connect SDA and SCL to their required pull-ups and do not exceed the 2.5 V to 6 V operating range. Quasi-bidirectional inputs are internally pulled high, so external circuitry must actively sink the relevant port low to register a logic-low state. Confirm output-current requirements and bus timing before driving heavier loads. This page combines manufacturer specifications, interface behavior, pin-level guidance, practical design notes, and same-package alternatives to support device selection, PCB layout, firmware planning, and sourcing decisions.

RFQ پەیوەندی
PCF8574PW - 8-bit I2C I/O Expander 20-TSSOP | Texas Instruments (Tape & Reel)
PCF8574PW

PCF8574PW - 8-bit I2C I/O Expander 20-TSSOP | Texas Instruments (Tape & Reel)

The Texas Instruments PCF8574PW is a remote 8-bit I/O expander for the I2C bus, designed for 2.5 V to 6 V VCC operation, packaged in a 20-pin TSSOP (PW) with Tape and Reel packaging. It provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface (serial clock SCL, serial data SDA) and supports an interrupt (INT) output to flag input changes to the host. An I/O expander is a type of interface IC that sits between a host controller (typically a microcontroller with limited GPIO) and external peripherals, translating a serial bus into multiple parallel digital lines. The PCF8574 belongs to the I2C I/O expander family -> interface IC -> integrated circuit -> semiconductor. By cascading multiple devices, designers can scale I/O count without redesigning the host board, making I/O expanders essential in space-constrained and pin-limited embedded designs. Key features include 8 quasi-bidirectional I/O pins, 100 kHz I2C clock rate, three hardware address pins (A0-A2) allowing up to 8 devices on the same bus (16 combined with PCF8574A), an active-low interrupt output that wakes the host on input changes, and low standby current of 2.5 uA typical. The PCF8574 uses the I2C address base 0x20 (PCF8574A uses 0x38), supporting up to 16 devices on a single bus for 128 I/Os. The quasi-bidirectional I/O architecture eliminates the need for a direction control register by using a clever pull-up/pull-down scheme, simplifying firmware. Each I/O can source 25 mA (LED drive capability) and sink up to 25 mA, sufficient to drive LEDs, keypads, or relay coils directly without buffering. Typical applications include keypad scanning for human-machine interfaces, LED driving for status indicators and display backlights, GPIO expansion for Raspberry Pi or ESP32-based projects, and industrial control panels. The wide 2.5 V to 6 V VCC range allows interfacing with both 3.3 V and 5 V logic without level shifters. When designing with this device, note that quasi-bidirectional I/Os are weak when transitioning to high - add an external pull-up resistor (typically 10 kohm) if driving heavy capacitive loads. The INT pin must be acknowledged by the host to clear the interrupt condition. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
PCF8574PWG4 - 8-Bit I2C I/O Expander | Texas Instruments
PCF8574PWG4

PCF8574PWG4 - 8-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCF8574PWG4 is an 8-bit I/O expander for I2C-controlled remote input/output applications, operating at up to 100 kHz and housed in a 20-pin TSSOP package. The device provides eight quasi-bidirectional I/O lines, an I2C interface, power-on reset, and an interrupt output for remote peripheral control. An I/O expander, also called a port expander, increases the number of digital input and output pins available to a host microcontroller. The PCF8574 belongs to the interface-controller hierarchy: I/O expander → interface IC → integrated circuit → semiconductor. Its I2C interface allows a microcontroller to read and control eight external lines using serial data and clock signals instead of dedicating eight parallel GPIO pins to every peripheral. The PCF8574PWG4 features an 8-bit quasi-bidirectional port, a 100 kHz I2C interface, and a 20-pin TSSOP package. Its interrupt output can alert the host when an input state changes, helping the controller avoid continuous polling. Power-on reset provides a defined startup state for the I/O port, while the quasi-bidirectional outputs can source or sink current depending on operating state. The I2C interface supports connection to a broad range of microcontrollers and embedded systems. Address selection is commonly implemented through input pins, allowing multiple expanders to share the same bus when the device configuration supports it. Because the port uses quasi-bidirectional structures, designers should review the device datasheet for output-drive, input, pull-up, and current-limit details before driving external loads. Typical uses include reading push buttons and selectors, controlling LEDs or discrete relays, monitoring digital sensors, and expanding the I/O capacity of industrial controllers, appliances, instruments, and consumer equipment. The 20-pin TSSOP package also supports compact board layouts where a larger dual-inline package would be inconvenient. For a new layout, route the I2C pins according to the datasheet pin description and place pull-up resistors close to the bus master. Confirm the logic-level voltage of every connected device, preserve the power-on reset behavior, and calculate the total port and bus loading before enabling multiple expanders. Use the manufacturer pin-description table when assigning PCB tracks and connector signals. This product page organizes the exact MPN, package, interface details, verified distribution information, replacement guidance, and practical integration considerations for engineers evaluating the PCF8574PWG4.

RFQ پەیوەندی
PCF8574PWR - 8-bit I2C I/O Expander 20-TSSOP | Texas Instruments
PCF8574PWR

PCF8574PWR - 8-bit I2C I/O Expander 20-TSSOP | Texas Instruments

The Texas Instruments PCF8574PWR is a remote 8-bit I/O expander for the I2C bus, designed for 2.5 V to 6 V VCC operation, packaged in a 20-pin TSSOP (PW) with Tape and Reel packaging. It provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface (serial clock SCL, serial data SDA) and supports an interrupt (INT) output to flag input changes to the host. An I/O expander is a type of interface IC that sits between a host controller (typically a microcontroller with limited GPIO) and external peripherals, translating a serial bus into multiple parallel digital lines. The PCF8574 belongs to the I2C I/O expander family -> interface IC -> integrated circuit -> semiconductor. By cascading multiple devices, designers can scale I/O count without redesigning the host board, making I/O expanders essential in space-constrained and pin-limited embedded designs. Key features include 8 quasi-bidirectional I/O pins, 100 kHz I2C clock rate, three hardware address pins (A0-A2) allowing up to 8 devices on the same bus (16 combined with PCF8574A), an active-low interrupt output that wakes the host on input changes, and low standby current of 2.5 uA typical. The PCF8574 uses the I2C address base 0x20 (PCF8574A uses 0x38), supporting up to 16 devices on a single bus for 128 I/Os. The quasi-bidirectional I/O architecture eliminates the need for a direction control register by using a clever pull-up/pull-down scheme, simplifying firmware. Each I/O can source 25 mA (LED drive capability) and sink up to 25 mA, sufficient to drive LEDs, keypads, or relay coils directly without buffering. Typical applications include keypad scanning for human-machine interfaces, LED driving for status indicators and display backlights, GPIO expansion for Raspberry Pi or ESP32-based projects, and industrial control panels. The wide 2.5 V to 6 V VCC range allows interfacing with both 3.3 V and 5 V logic without level shifters. When designing with this device, note that quasi-bidirectional I/Os are weak when transitioning to high - add an external pull-up resistor (typically 10 kohm) if driving heavy capacitive loads. The INT pin must be acknowledged by the host to clear the interrupt condition. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
PCF8574RGTR - 8-Bit I2C I/O Expander | Texas Instruments
PCF8574RGTR

PCF8574RGTR - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments PCF8574RGTR is an 8-bit I2C/SMBus input/output expander with interrupt, operating from 2.5 V to 5.5 V at up to 100 kHz in a 16-pin VQFN (RGT) package measuring 3 mm by 3 mm. It adds eight quasi-bidirectional GPIO lines to a host microcontroller through a two-wire serial bus. An I/O expander is an interface IC that extends the number of general-purpose input and output pins available to a microcontroller or system-on-chip. The PCF8574 belongs to the parallel I/O expander family within the interface IC hierarchy, connects to a host through I2C, and presents each remote port as a standard logic-level GPIO. Its compact package and interrupt output make it useful when a design lacks sufficient pins for switches, indicators, relays, or control inputs. Key features include eight configurable I/O ports, operation from 2.5 V to 5.5 V, a 100 kHz I2C interface, three hardware address inputs, and an active-low open-drain interrupt output. The interface is compatible with both I2C and SMBus systems, while the small 3 mm by 3 mm VQFN footprint saves board area in space-constrained control boards. The manufacturer specifies an operating temperature range of -40 °C to +85 °C. Each port can operate as an input or output and is designed for devices that source or sink modest logic-level current. The quasi-bidirectional architecture includes a weak output driver that can be actively pulled low or released for input detection. This arrangement works well with pull-up-based buses and typical digital peripherals, although firmware must account for the port's input and output drive characteristics when resolving multiple low-level signals. Typical uses include expanding GPIO on an 8-bit microcontroller, driving LED indicators and key inputs in an industrial control panel, reading switch banks in an appliance, and supporting addressable bus nodes in embedded equipment. The interrupt pin can wake or notify the host when a port changes state, reducing the need for continuous polling when the application allows interrupt-driven I/O handling. Place pull-up resistors on SDA and SCL according to the bus voltage and capacitance, and route the interrupt trace away from high-current switching nodes. Confirm that connected peripherals remain within the port's voltage, current, and timing limits. The exposed-pad package also requires a proper thermal and electrical ground connection under the device. This page combines manufacturer specifications, package details, application guidance, and verified drop-in alternatives in a form useful for schematic capture, PCB layout, sourcing, and lifecycle review. It also highlights the differences between electrically similar expanders that use different port architectures.

RFQ پەیوەندی
PCF8574T - 8-bit I2C I/O Expander, SOIC-16 | NXP Semiconductors
PCF8574T

PCF8574T - 8-bit I2C I/O Expander, SOIC-16 | NXP Semiconductors

The NXP Semiconductors PCF8574T is a remote 8-bit CMOS I/O expander for the two-line bidirectional I2C-bus, supporting 2.5V to 6V VCC operation and providing general-purpose remote I/O expansion for most microcontroller families. The PCF8574T integrates a quasi-bidirectional 8-bit parallel I/O port (P0-P7), an I2C-bus interface, and a hardware interrupt output (INT) that signals the host controller when input state changes, all in a 16-pin SOIC surface-mount package. What is an I/O expander? An I/O expander is an integrated circuit that adds additional general-purpose input/output pins to a microcontroller through a serial bus (typically I2C or SPI). It sits in the hierarchy: GPIO extender -> I/O expander -> interface IC -> digital semiconductor. The PCF8574T specifically uses a quasi-bidirectional I/O architecture that eliminates the need for a direction control register - each pin can be used as either input or output without explicit mode configuration. Key features of the PCF8574T include three hardware address pins (A0-A2) that allow up to 8 PCF8574T devices to share the same I2C-bus (selectable I2C addresses 0x20-0x27). The quasi-bidirectional I/O architecture requires no direction register, simplifying software drivers. The open-drain interrupt output (INT) is asserted when any input changes, enabling efficient event-driven polling. The device operates across 2.5V-6V VCC, supports I2C standard-mode (100 kHz) and fast-mode (400 kHz), and consumes very low standby current. The PCF8574T uses a silicon CMOS process with an open-drain interrupt line and open-drain bidirectional I/O pins. The quasi-bidirectional architecture drives a weak pull-up (current source) when outputs are HIGH and a strong pull-down when LOW, allowing the same pin to be read back without changing direction. The I2C slave address is programmed via A0, A1, A2; slave base address is 0x20 for PCF8574 and 0x38 for PCF8574A - this distinction is critical when selecting between variants. Typical applications include keypad scanning on human-machine interfaces (HMIs), LED driving on display panels and indicator boards, LCD bias generation, sensor monitoring via additional GPIOs, and adding GPIOs to small microcontrollers. The 0x20-0x27 address range also makes it ideal for multi-bus I/O expansion where multiple expanders must coexist. When designing with the PCF8574T, add 100 kohm pull-up resistors on SDA and SCL because the PCF8574T uses open-drain drivers (no internal pull-ups). Note that the "T" suffix denotes the SOIC-16 package, while "N" denotes DIP-16 and "BS" denotes SSOP-16 - same silicon die, different packages. The PCF8574 (base address 0x20) and PCF8574A (base address 0x38) are NOT drop-in replaceable without changing the host firmware address. This page consolidates distributor pricing, parametric equivalents (TI PCA9534, PCA9554, PCA9557), drop-in alternatives in the SOIC-16 footprint, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
PCF8574TD - 8-bit I2C I/O Expander, SO-16 | NXP Semiconductors
PCF8574TD

PCF8574TD - 8-bit I2C I/O Expander, SO-16 | NXP Semiconductors

The NXP PCF8574TD is a remote 8-bit I/O expander for the I2C-bus, supplied in a 16-pin SO (Small Outline) package with a -40C to +85C industrial temperature grade. The device operates from 2.5 V to 6 V VCC and provides eight quasi-bidirectional input/output pins that can be independently assigned as inputs or outputs, all controlled through the standard two-wire I2C interface. An I2C I/O expander is a type of interface IC that sits between a microcontroller and peripheral signals, translating serial commands from the I2C bus into parallel GPIO operations. The PCF8574 belongs to the I/O expander sub-category of interface ICs, itself part of the broader power management and inter-chip communication hierarchy. By adding eight extra quasi-bidirectional ports over only two wires, the PCF8574 lets small microcontrollers control keypads, LCDs, LEDs, and relays without sacrificing native pins for other functions. Key features of the PCF8574TD include a maximum standby current of 10 uA, an open-drain interrupt output (INT) that signals the host when an input changes state, and three hardware address pins (A0-A2) that allow up to eight PCF8574 devices on the same I2C bus (64 I/O lines). The quasi-bidirectional I/O architecture requires no direction-control register: a pin set HIGH is weakly pulled up (~100 uA source), and a pin set LOW is strongly pulled down, simplifying firmware and PCB layout. The PCF8574 uses a fixed I2C slave address of 0x20-0x27 (set by A2:A0), which distinguishes it from the PCF8574A variant (address range 0x38-0x3F). Both share the same SO-16 footprint, enabling dual-sourcing designs. The silicon CMOS process keeps quiescent current low enough for battery-backed applications. Typical applications include keypad scanning, LED driving arrays, LCD module backpacks, relay/Opto-coupler interfacing, and general-purpose GPIO expansion on 8051, ARM Cortex-M, ESP32, PIC, AVR, and MSP430 microcontrollers. The interrupt pin eliminates polling overhead in button or switch-matrix designs. When designing with this device, place a 0.1 uF decoupling capacitor close to VCC and 100 kohm pull-up resistors on SDA, SCL, and INT. Verify your firmware does not read the input port during the I2C ACK bit, as a transient high-current condition can occur on the quasi-bidi pins. This page synthesizes distributor pricing, drop-in alternatives (same-brand NXP variants and cross-brand TI equivalents), and practical design notes that complement, rather than duplicate, the manufacturer datasheet.

RFQ پەیوەندی